Winifrede Surface Mine Coal

When standing from a kneeling position employee felt popping in his left knee. Strain to left knee. Employee began missing work 12/5/2014 (arthroscopic knee surgery).

CLAIM FILED FOR PNEUMOCONIOSIS. X-RAY READ DATE 6/7/14. TERMINATION DATE OF 10/8/2010

The employee was installing a conveyor motor on a 14-15 JOY continuous miner using a hoist and a nylon strap. As the mechanic was repositioning the motor in the miner pan, it started to slip, he had his hand on the motor to guide it and his left pinky finger got caught between the nylon strap and the motor. As a result this cut his finger above the first joint.

An employee of Maxxim Rebuild Co, LLC an affiliate of ALPHA Natural Resources, who works at the shop adjacent to the pre plant, was outside in the storage area of the shop, conducting an inspection on a piece of belt line for thickness. As the employee bent over to conduct the inspection, a stick poked him in the left eye, scratching the eye. He was wearing safety glasses.

EE was welding angle braces to the load out conveyor truss due to structural deficiencies. He was working from a temporary platform. EE was wearing a harness & had 2 lanyards attached to the structure. For an unknown reason, he unharnessed the lanyard from his harness & slipped from the platform & fell approx. 25' to the ground below fracturing his leg, pelvis & a vertebrae.

While removing fuse from fuse holder the fuse fell off the hot stick approximately 50' striking the employees right index finger causing a laceration.

Employee was removing a rub rail from a continuous miner at the rebuild shop. After removing the pins that hold it place, the rail dropped and caught three of left fingers between the rail and the water spray unit. This resulted in 7 stitches used to close a cut on his left middle finger. The other two fingers were only bruised.

EE was unloading a piece of 3" conduit from a truck and dropped it on his right hand, fracturing the tip of his finger.

EE was washing the 1st floor of the plant, when he tripped on the wash down hose and fell, injuring his knee and lower back.

R-3 refuse belt caught fire due to a faulty bearing and could not be extinguished within 30 minutes. The belt was broken and the fire was extinguished with no injuries.

Helping move scaffold to work area, developed pain in low back area. Saw Dr. on 9-30-08, taken off work until 10-13-08.

Employee was helping close doors on empty coal cars. He was holding door in closed position, ready to roll down latch, his bar slipped causing him to fall. As he fell he twisted to the right injuring his right knee and ankle.

Employee cleaning rock from catwalk of mids belt. Something fell from plant feed belt, struck him on the head. Taken to E.R. for treatment, stitches used to close the wound.

Helping replace #1 CM dryer chute 2nd floor of plant, chute caught on edge of hopper. Using #2 hoist to pull #1 chute, using slate bar to pinch chute over hopper, with pressure on chute it came across hopper, struck employee in face causing injury. Employee had scheduled days off and did not start to miss work until 7-21-2008.

Employee helping carry castings primary vessel on 5th floor, 65-70 lb each. Injured 4-18-08, kept working until saw doctor on 6-10-08, had surgery 7-28-08, return to work 8-11-08. 8-11-08 First time Safety Dept notified.

Bending down beside CM frame in shop. Stepped on hyd.hose attached to jack, pulled jack down onto his left hand causing injury. X-ray positive, fracture to had behind left pinky finger.

Threading nut onto all thread with impact wrench, injured left hand. Taken to E.R. for treatment, used stitches to close wound.

Employee was shoveling material from tailpiece at R-4 refuse belt. About 8:30 P.M. he developed pain in the low back radiating down around the left groin area. He was taken to the Williamson Memorial E.R. for treatment. Attending doctor determined he had low back muscle strain.

Employee was replacing flights in the primary vessel on 5th floor. While lifting them out and onto the floor he developed pain in abdomen. E.R. exam revealed small hernia in abdominal area.

Employee was removing a piece of beltline from the #1 reclaim belt; pulling through the HD & take-up, out of the idlers. During this job he developed burning in lower right abdominal area. He continued to work, but now has had hernia surgery on 8/4/06, and has begun to miss work on 8/1/2006.

Working on grid coupling #46 screen, dropped bolt, reached to pick up bolt, flop gate fell onto left hand, pinching it between gate and metal frame of screen.

Employee is a raw coal dozer operator who was helping the welder this day. He bent over to pick up a chain fall & experienced pain in his lower abdomen. He completed the day & began his 4 days off (works 4 on & 4 off). Saw the Dr. on 4/25/06, had surgery on his left side 5/23/06 & on his rt. side 7/24/06. We learned of LTA 8/15/06 when Supt. called to ask the employee.

Employee broke utility knife blade. Remainder of blade caused laceration to left knee. He was taken to williamson memorial for treatment, received stitches to close wound.

INSTALLING TURN TABLE PINS W/BOOM UPSIDE DOWN, HELD WITH RAILROAD JACK. RELEASED JACK, WEIGHT OF BOOM CAUSED LEFT HAND TO BE CAUGHT BETWEEN JACK LEVER & TURNTABLE.

EE WAS TRYING TO FREE A STUCK TAILGATE ON A COAL TRUCK. AN OBJECT EJECTED FROM THE TRUCK AND STRUCK EE OVER HIS LEFT EYE. EE WAS TAKEN TO ER FOR TREATMENT. STITCHES WERE USED TO CLOSE THE WOUND.

EMPLOYEE BURNED RIGHT ARM WHILE WELDING BUT DID NOT REPORT INJURY UNTIL 8/14/04 WHEN MIDICAL BILL CAME IN AND HE DECIDED TO FILE UNDER WORKER'S COMP.

EE WAS ASSISTING WITH CHANGE OUT OF A TRANSFORMER.DISCONNECT WAS LOCKED & TAGGED OUT. THE DISCONNECT MALFUNCTIONED, LEAVING TRANSFORMER ENERGIZED. EE CAME IN CONTACT WITH POWER.

EE's hand was grasping the chain sling from an overhead crane while attempting to raise equip. When the crane took slack out, his thum was smashed between sling and equipment.

EE WAS REMOVING LARGE PIECE OF METAL FROM BELT & MASHED FINGER BETWEEN METAL & BELT STRUCTURE REQUIRING STITCHES.

EE WAS INSTALLING BELT HANGER ON SILO BELT WHEN BELT CAUGHT WRENCH AND LACERATED RIGHT HAND, REQUIRING STITCHES.

MEMBER WAS USING BANDING TOOL TO APPLY END TO WATER HOSE. AFTER HOSE WAS BANDED HE WAS TRYING TO REMOVE AN EXCESS PIECE OF BANDING MATERIAL FROM THE TOOL AND IN THE PROCESS HE LACERATED HIS HAND REQUIRING STITCHES.

MEMBER WAS CUTTING A PIECE OF BELT OUT OF A ROLLER WITH A UTILITY KNIFE AND LACERATED HIS INDEX FINGER REQUIRING STITCHES.

MEMBER WAS MOVING LARGE ROCK BETWEEN BELT AND STRUCTURE AND CAUGHT FINGER BETWEEN ROCK & STRUCTURE CAUSING LACERATION.

EE WAS GETTING RAILROAD JACK OUT OF BACK OF TRUCK AND WAS STANDING ON SIDE STEP WHEN HIS FEET SLIPPED OFF STEP CAUSING HIS THUMB TO BE CAUGHT BETWEEN JACK AND CORNER OF BED CAUSING A LACERATIO N THAT REQUIRED STITCHES.

MEMBER WAS WALKING DOWN STEPS FROM 2ND FLOOR TO 1ST FLOOR AND SLIPPED AND FELL INJURING BACK. MEMBER DID NOT START MISSING WORK UNTIL 3/7/-3 DUE TO HIS WORK SCHEDULE.

EE AND CO-WORKER WERE SENT TO UNPLUG THE REFUSE CHUTE. EE WAS USING A SLATE BAR IN AN EFFORT TO UNPLUG THE CHUTE. ON ONE OF THE SWINGS THE BAR GLANCED OFF A ROCK AND EE LOST HIS FOOTING, STRAI NING HIS BACK.

EE WAS PICKING UP BELT IDLERS & THROWING INTO BACK OF PU WHEN HE FELT A POP IN HIS RIGHT SHOULDER & FELT PAIN. EE DID NOT START MISSING WORK UNTIL 3/5/03 WHERE SURGERY WAS PERFORMED TO REPA IR SHOULDER

EE WAS SERVICING HIS COAL TRUCK. HE WAS STANDING ON THE FUEL TANK STEP CHANGING AN AIR FILTER WHEN HE SLIPPED AND FELL STRIKING HIS LEFT ELBOW AGAINST THE GROUND. HE DID NOT SEEK MEDICAL ATTEN EITON UNTIL LATER IN THE DAY AT WHICH TIME HE WENT TO THE WILLIAMSON MEMORIAL HOSPITAL. X-RAYS REVEALED A HAIRLINE FRACTURE TO HIS ELBOW. EE WAS TAKEN AWAY FROM WORK UNTIL 7/29/2002.

EE WAS REMOVING THE DISCHARGE LINE FROM A PUMP. WHEN THE VICTROLIC COUPLING WAS REMOVED SCALDINGWATER SPRAYED ON HIS HANDS CAUSING SECOND DEGREEBURNS.

EMPLOYEE WAS USING AN IMPACT WRENCH TO REMOVE AHYDRAULIC PUMP WHEN THE SOCKET BURST LACERATING HIS HAND. STITCHES WERE REQUIRED TO CLOSE THE WOUND.

EE WAS REPAIRING A TRAINING MODEL SELF RESCUER. WHILE USING A POCKET KNIFE TO REMOVE A MOISTURE INDICATOR, THE KNIFE SLIPPED STRIKING & CUTTING HIS LEFT HAND BETWEEN THUMB & FINGER. STITCHES.

EE WAS ATTEMPTING TO UNSTOP THE CLEAN COAL SAMPLER. HE DID NOT DISCONNECT THE POWER TO THE SECONDARY CUTTER ON THE SAMPLER. YIS FOREHEAD CAME IN CONTACT WITH THE SWEEP ARM CAUSING A LACERATION THAT REQUIRED STITCHES.

EE WAS USING A 1/2" DRILL WHEN THE DRILL BIT CAUGHT FOUL. THE DRILL TWISTED HIS HAND CAUSING A FRACTURE TO A SMALL BONE IN HIS LEFT HAND.

EE WAS UNPLUGGING THE #2 RECLAIM SHUTE. THE AREA WAS WET AND SLIPPERY. EE SLIPPED AND TWISTED HIS KNEE.

EMPLOYEE WAS PREPAIRING TO SERVICE A DOZER ON THE IMPOUNDMENT. WHEN HE OPENED THE DOOR TO THE TOOLBOX ON THE SERVICE TRUCK TO RETRIEVE GREASE RACKS, AN 18 LB SLEDGE HAMMER FELL FROM THE TOP SHELF AND STRUCK HIM BETWEEN THE EYES. HE SUSTAINED A LACERATION REQUIRING STITCHES.

ON APRIL 10, 2000, DUE TO AND OCCUPATIONAL ILLNESS, AS SUBSTANTIATED BY MEDICAL RECORDS AND REPORTS, EMPLOYEE BECAME UNABLE TO WORK BECAUSE OF THE AILMENTS DESCRIBED IN THE MEDICAL REPORTS. TH IS WAS NOT DUE TO A SINGLE EVENT AT THE MINE.

EE WAS USING AN ALLEN WRENCH. HE WAS REMOVING A WEAR PLATE FROM INSIDE THE #2 SLOPE, SLURRY PUMP. THE WRENCH SLIPPED AND EE S HAND STRUCK THE EDGE OF THE VOLUTE LINER ON THE PUMP. THE EDGE OF THE LINER WAS EXTREMELY SHARP AND IT CUT THROUGHHIS GLOVE AND CAUSED A LACERATION TO HIS RIGHT THUMB. EE RECEIVED STITICHES.

EMPLOYEE WAS MOUNTING A D10N DOZER WHEN HE LOST HIS FOOTING ON THE WET TRACK AND FELL. EMPLOYEE STRUCK HIS RIGHT ELBOW ON THE TRACK CAUSING A FRACTURE TO THE RADIUS.

EMPLOYEE WAS ATTEMPTING TO RIDE DOWN THE MANLIFT FROM THE 5TH FLOOR OF THE PLANT CARRYING A SMALL STEP LADDER BETWEEN HIM AND THE MANLIFT BELT. AS THE EMPLOYEE STEPPED ONTO THE MANLIFT AND STA RTED DOWN FROM THE 5TH FLOOR, HIS LIGHT GOT CAUGHT ON THE EDGE OF THE FLOOR GRATING WHICH PULLED HIM OFF THE LIFT STEP AND ALLOWED HIM TO FALL APPROX. 19 FT. FROM THE 5TH FLOOR TO THE 4TH FLO

EMPLOYEE WAS CUTTING THE BOTTOM DECK OUT OF A FEEDER WHEN THE WELD ON THE DECK BROKE, ALLOWING THE METAL TO FALL ENTRAPPING HIS LEFT HAND AND FRACTURING 3 OF HIS FINGERS.

EMPLOYEE WAS CLIMBING LADDER ON TRUCK TO CHECK AUTOMATIC TARP FOR MALFUNCTION. HIS FOOT SLIPPED, HE FELL OFF TRUCK ONTO BLACKTOP FRACTURING FOOT.

EE HAD CUT A SMALL HOLE THROUGH THE EXTERIOR WALL OF THE MCC 3 RM FOR THE DISCHARGE END OF THE VACCUM. HE WAS ATTEMPTING TO BEND SOME ROUGH EDGES AROUND THE HOLE IN THE METAL SHEETING WHEN HE CUT HIMSELF. THE EE SUFFERED A SMALL LACERATION TO THE BACKSIDE OF HIS LEFT HAND THAT REQUIRED 4 STITCHES.

ONCE EE CROSSED OVER THE ELEVATED BRIDGE THAT LEADS TO THE GUARD SHACK FROM THE PARKING LOT, HISFOOTING SLIPPED AS HE DESCENDED THE STAIRCASE. HE FELL APPROX 5 STEPS BEFORE GAINING CONTROL OF HIMSELF. EE SUFFERED FRACTURED TAILBONE DUE TO THIS ACCIDENT.

THE EE WAS UTILIZING A HAND GRINDER TO GRIND DOWN WELDS ON A CHUTE WHEN THE GRINDER KICKED BACK AND STRUCK HIM IN THE RIGHT LEG. THIS RESULTED IN A LACERATION TO HIS RIGHT LEG AND FORTY STITCH ES WERE REQUIRED TO CLOSE THE WOUND.

THE EMPLOYEE DISCOVERED A LEAK IN A PIPE ON THE SECONDARY VESSEL RETURN LINE. HE PROCEEDED TO THE 2 1/2 FLOOR, WHERE HE CRAWLED UNDER THE HANDRAIL AND WALKED 15 FEET OUT ON A BEAM TO THE PIPE. HE TAPED THE PIPE AND TURNED TO WALK BACK WHEN HE SLIPPED AND FELL ONTO THE LOWER FLOOR. THE EMPLOYEE SUFFERED SIX BROKEN RIBS ON HIS RIGHT AS A RESULT OF THIS ACCIDENT.

EE WAS PREPARING TO WELD A 7"X7" PLATE ONTO THE MIDDLINGS CHUTE WHEN THE ACCIDENT OCCURRED. HE CARRIED THE PLATE UP A LADDER AND PLACED IT ON THE CHUTE. HE CLIMBED DOWN THE LADDER TO GET A WEL DING ROD. AS HE CLIMBED BACK UP THE LADDER THE PLATE VIBRATED OFF THE CHUTE AND STRUCK HIM OVER HIS RIGHT EYE. THIS CAUSED A LACERATION THAT REQUIRED SIX STITCHES.

A NON-INJURY ACC OCCURED AT THE NO.2 RAW COAL STOCKPILE OF THIS PREPARATION PLANT. A DOZER OPERATOR WAS ENTRAPPED FOR APPROX ONE HR & 40 MINS WHEN THE COAL PILE COLLAPSED, COVERING THE DOZER

INJURED WAS REPLACING THE COVER ON A CMI DRYER WHEN HIS THUMB [RIGHT THUMB] WAS PINCHED BETWEEN THE COVER & DRYER FLANGE. THIS RESULTED IN A FRACTURE OF HIS RIGHT THUMB.

USING A CUTTING TORCH. FIRE IGNITED IN THE LINE. CO-WORKER CLAMPED OFF LINE AND LEFT TO TURN OFF THE VALVE AND FIRE IGNITED AGAIN. EMPLOYEE TRIED TO GET AWAY FROM THE FLAME AND FELL OFF A 8 TO 10' WALL INTO A THICKNER SLUDGE POND.

INJURED WAS USING A BAR TO CLOSE DOORS ON COAL CARS WHEN THE BAR SLIPPED, CAUSING HIM TO FALL TO FALL TO THE GROUND. THIS ACCIDENT RESULTED IN A FRACTURE OF HIS LEFT ANKLE.

INJURED WAS REMOVING GATE FROM RAW COAL FEED CHUTE WHEN HIS FINGERS ON THE LEFT HAND WERE CAUGHT IN A PINCH POINT. THIS RESULTED IN A LACERATION ON THE RING FINGER ON HIS LEFT HAND THAT REQUIR ED 3 STITCHES.

EE WAS DRIVING A WHEEL LOADER UP THE HILL. THE LOADER BEGAN GOING BACKWARDS OVER AN IMPOUNDMENT APPROX 1000'FT. THE LOADER HIT A LOADED COAL TRAIN.

EMPLOYEE WAS IN PROCESS OF INSTALLING A ELECTRIC HEATER WHEN IT FELL STRIKIGN HIS LEFT HAND RESULTING IN A LACERATION TO HIS LEFT THUMB. THIS LACERATION REQUIRED STITCHES.

EMPLOYEE WAS ON A LADDER WELDING ON PREP PLANT FIRST FLOOR. HE WAS VERY WET WITH SWEAT DUE TO HUMIDITY. HE WAS SHOCKED BY THE WELDING LEAD AND FELL OFF THE LADDER. HE WAS CAUGHT BY A CO-WORKER WHO WORKS FOR ANOTHER CONTRACTOR.

EMPLOYEE WAS WALKING THROUGH PLANT, SLIPEPD AND FELL ON FLOOR, ALLEGED THAT HE INJURED HIS BACK.

INJURED WAS USING A HAND GRINDER ON A PIECE OF METAL WHEN IT SLIPPED AND STRUCK HIS LEFT ARM CAUSING A LACERATION.

PERSON WAS ON THE 6TH FLOOR OF THE PREP PLANT TRYING TO GET A FLOP GATE TO THROW. THE GATE BECAME FOULED, WHILE HE WAS TRYING TO GET IT UNFOULED THE PIN CAME OUT OF THE JACK & CAUSED HIS FINGE RS TO GET CAUGHT BETWEEN THE GATE & CHUTE. THIS RESULTED IN 2 FRACTURED FINGERS OF THE RIGHT HAND.

WAS ROLLING ABOUT 3FT PIECE OF PIPE OFF BOTTOM FLOOR PREPPLANT FELT PAIN IN LOWER BACK THAT WOULD NOT GO AWAY

REMOVE AIR HOSE FROM TANK. FROZE UP TO REMOVE ICE BROKE LOOSE KNOCKING HARD HAT AND GLASSES OFF, SHUT VALVE TO STOP FLOW. STILL HAD PRESSURE ON LINE. LINE STARTED JUMPING AROUND THROWING ICE H ITTING HIM IN RIGHT SIDE FACE AND EYE, ABRASION TO EYE, SMALL INCISION TO FACE AROUND EYE.

I WAS SQUIRTING DIESEL WITH A ROSE GUN ONTO BELT ROLLERS WHICH WERE FROZEN DUE TO THE FRIGID TEMP. FUEL SPLASHED BACK INTO RIGHT EYE.

INSTALLING A TRANSMISSION IN A 14G MOTOR GRADER, UNDER WET & MUDDY CONDITIONS, EMPLOYEE PUSHING ON THE TRANSMISSION WITH HIS LEFT LEG, CAUSING A MUSCLE SPRAIN.

JAMES WAS PUSHING COAL ON #1 CLEAN COAL PILE WHEN D9N DOZER BACKED UP AND FELL IN FEEDER HOLE, ENTRAPING DOZER AND OPERATOR FOR ONE HOUR.

TWO INDIVIDUALS SUPRISED EACH IN DOORWAY. ONE PERSON RAISED HIS ARMS UP WITH OPEN RAZOR KNIFE STILL IN HIS HAND. OTHER PERSON RAISED HIS ARMS ALSO. RIGHT FOREARM CAME IN CONTACT WITH BLADE RES ULTING IN CUT.

WHILE CROSSING STOCKPILE, FRONT OF DOZER DROPPED SUDDENLY OVER OUTSIDE EDGE THROWING OPERATOR FORWARD WITH MOUTH HITTING RADIO MOUNTED ON DASH.

EE WAS STEPPING ONTO THE FIRST STEP ENTRING THE GUARD SHACK WHEN HE SLIPPED HE TRIED TO LEGAIN HIS BALANCE AND FELL ON TO THE NEXT SET OF STEPS INJURING HIS ARM.

HE WAS TAKING #32 CYCLONE WHOSE SCREEN OUT OF SERVICE, WHEN A SMALL (DUST LIKE) PIECE OF METAL LODGED IN HIS RIGHT EYE.

EE WAS WORKING ON A PAYHAULER PH-350 WHEN HE STEPPED OFF THE TRUCK ONTO A CRIB BLOCK TWISTING HIS ANKLE AND CAUSING THE INJURY.

EE WAS CHANGING SKIRT BOARD RUBBER ON LEFT SIDE OF BELT HE SAID HE WAS LOSING BELTS WHEN ONE BELT CAME LOOSE CAUSED HIM TO SLIP ON LADDER JAMMING HIS LEFT UPPER ARM BETWEEN A BELT IDLER & AN A NGLE BRACE

INJURED WAS HOLDING SOCKET ON IMPACT WRENCH WHEN THE PIN THAT HOLDS ALLEN WRENCH IN SOCKET CAME LOOSE AND CUT HIS LEFT THUMB.

WHILE TRYING TO DISLODGE A TIMBER FROM A CHUTE WITH A SLATE BAR THE BAR SLIPPED OFF EE HIT HIS RIGHT HAND ON HAND RAIL.

EE WAS ATTEMPTING TO CLEAR A BLOCKED CHUTE WHEN HE WAS STRUCK FROM BEHIND BY A PIECE ROCK.

EE WAS UNLOADING A FLAT BED TRUCK THAT HAD SNAP ON BINDER OVER ITS LOAD WHILE RELEASING THE BINDER WITH A CHEATER PIPE THE PIPE SLIPPED STRIKING HIM OVER THE RIGHT EYE

55061S BRINGING A PIECE OF EQUIPMENT FROM THE OLD IMPOUNDMENT TO THE PREPARATION PLANT WHEN HE LOST CONTROL OF THE 950 CATLOADER HE WAS ABLE TO STEER INTO THE BERM BEFORE OVERTURNING EE RECEIV 54031CERATIONS ON HIS LEFT ARM & BACK WHEN THE LOADER OVERTURNED

EMPLOYEE WA OPERATING A CONCRETE CURE DRILL WHENTHE DRILL BIT "HUNG UP" IN THE CONCRETE SLAB CAUSING THE DRILL TO TWIST AND HIT THE EMPLOYEES LEG.

HE WAS UNLOADING A METAL BOX FROM A CART AND GOT HIS HAND BETWEEN BOX AND CART AND MASHED HIS HAND.

COMING INTO REFUSE BIN TRUCK HIT HOLE IN ROAD CAUSING IT TO BOUNCE TWISTING NECK & SHOULDER CAUSING PAIN IN NECK & RT ARM

STEPPED ON RAZOR IN BATH HOUSE CUTTING LEFT FOOT.

CHANGING BELTS ON NO. 1 TUNNEL VENT FAN. RAISED MOTOR BASE WITH BAR TO PUT ADJUSTING BOLT IN PLACE BAR SLIPPED OUT CATCHING LEFT INDEX FINGER BETWEEN BASE AND FAN HOUSING.

EE WAS SHOVELING AT THE FACE OF THE RECLAIM TUNNEL WHEN A PIECE OF ROCK FALL FROM A BELT LINE RUNNING OVER HEAD IT APPEARS THE ROCK WAS DISCHARGED FROM THE COAL SAMPLER.

EMPLOYEE WAS WORKING ON TOP OF A TRUCK-CUTTING SCRAP METAL. THE LOAD SHIFTED KNOCKING HIM OFF THE TRUCK. HE LANDED ON HIS RT. FOOT, BREAKING HIS HEEL.

HE WAS CLIMBING OUT OF THE TRUCK CAB WHEN HIS FOOT SLIPPED FROM THE FIRST STEP CUASING HIM TO FALL TO THE GROUND INJURING HIS BACK AMD LEFT LEG.

STEPPED ON PIECE OF FLOOR DRAIN PIPING,PIPE FLIPPED,CAUSING INJURED TO FALL STRIKING HEAD,BACK AND THUMB.

REMOVING COVER FROM R/C RECLAIM #1 PAIN IN CHEST MUSCLE FROM LIFTING COVER -5 LB .

MOVING 02/ACTY BURNING CART & HURT BACK

RAN D7 DOZER OVER BIG ROCK.

HAD BEEN WORKIN1 IN A JOHN BOAT IN THE PLANTS THICKNER AFTER ABOUT ONE HOUR OF SITTING BENT OVER HE STARTED TO CLIMB OUT OF THE THICKNER AT WHICH TIME HE FELT A PAIN IN HIS LOWER BACK