Buscar en el registro

WHILE UNDOING BOLTS FROM MACHINE, A PIECE OF A RUSTY METAL BOLT GOT INTO THE EMPLOYEES RIGHT EYE.

EE STRUCK HAND WITH HAMMER WHILE HITTING A DRIVE SHAFT.

EE WAS CUTTING BAND ON A BUNDLE OF EMPTY BAGS. HE WAS PULLING THE KNIFE TOWARDS HIM. WHEN HE CUT THROUGH THE STRAP THE KNIFE CONTINUED ON AND HE STABBED HIMSELF ON THE INSIDE OF HIS LEFT THIGH .

WHILE ON CATWALK TIGHTENING BOLT ON APRON PAN EE LEANED OVER A PIECE OF I-BEAM SUPPORT WHILE PULLING ON A WRENCH HE FORCED HIS LOWER LEFT RIBS AGAINST THE I-BEAM RESULTING IN BRUISED RIB

EE STRUCK HIS HEAD AGAINST A BOLT ON A BRACKET WHEN THE WRENCH HE WAS USING TO FREE A PTO CABLEUNDER A STOCK TRUCK SLIPPED. HE JERKED HIS HEAD TO AVOID BEING STRUCK BY THE WRENCH, BUT STRUCK HIS HEAD AGAINST THE BOLT.

EE'S HAND WAS CAUGHT BETWEEN A STEEL BAR AND A CRUSHER PLATOFRM WHILE CLEARING A HANGUP. FIRST MEDICAL TREATMENT ON 7-17-02.

EE WAS CUTTING BUT HAD HIS LEFT HAND DIRECTLY ACROSS FROM HIM. THE CUTTING UTENSIL SLIPPED AND HE CUT HIS LEFT THUMB. (THE DELAY IN REPORTING THIS WAS NOTED DURING AN INTERAL AUDIT).

EE WAS HEATING UP COUPLING WITH A ROSE BUD TORCH SO THAT THE COUPLING COULD BE REMOVED. 2 OTHER EES WERE STRIKING THE COUPLING WITH 20# DEAD BLOW MALLETS. ONE OF THE MALLETS GLANCED OFF OF THE COUPLING STRIKING EE ON THE RIGHT SIDE OF HIS FACE.

WHILE ATTEMPTING TO KNOCK A TOOTH OUT OF A LOADER BUCKET A METAL FRAGMENT PUNCTURED HIS RIGHT ARM.

WHILE HAMMERING METAL WITH A SLEDGE HAMMER A PIECE OF METAL FLEW OFF AND STRUCK HIS RIGHT LOWER LEG CAUSING A PUNCTURE WOUND.

EE WAS REPLACING THE COUPLING BETWEEN THE CUTTER HEAD MOTOR AND GEAR BOX. WHILE DRIVING THE COUPLING ON W/ A HAMMER, HIS HAND SLIPPED AND HE STRUCK HI LEFT THUMB.

OUTSIDE/SWINGING A SLEDGE HAMMER TO DRIVE A PULLEY SHAFT BACK INTO BEARING HOUSING #3 FEED WEIGHT DISPLACED ON LEFT LEG/HEARD AND FELT KNEE SNAP/IMMEDIATE PAIN TIGHT ENCLOSED AREA.

EMPLOYEE WAS UNPLUGGING A CHUTE.

OVERSHOT FELL OUT OF THE MAST AND STRUCK EMPLOYEE ON THE HEAD, EMPLOYEE WAS WEARING A HARD HAT.

A FUEL/LUBE TRUCK DRIVER WAS CHANGING THE TEETH ON A 990 LOADER, USING A HAMMER 3 LB WHEN UPON STRIKING THE PIN A METAL PIECE HIT HIS UPPER LEFT LEG.

EE WAS CUTTING A PIECE OF RUBBER BELTING WITH A RAZOR KNIFE. WHILE PULLING THE KNIFE TOWARD HIM IT SLIPPED AND HE STABBED HIMSELF IN THE LEFT FOREARM.

EE WAS USING A CHISEL BRAND NEW TO SPREAD LINKS ON A TRACK SYSTEM. THE CHISEL SNAPPED IN HALF AND CUT HIM ABOVE THE RIGHT EYEBROW.

EMPLOYEE AND TWO OTHER EMPLOYEE'S WERE INSTALLING A WERA SLEEVE ON SHAFT WITH A HAMMER AND A PIECE OF BRASS. WHILE THE OTHER EE HIT THE BRASS PIECE ON ONE SIDE, IT SLIPPED AND HIT EE'S RIGHT T HUMB.

PULLING HARD ON A RATCHET TO BREAK A NUT LOOSE ON THE PLANT. ACUTE LS STRAIN

WHILE PRYING WITH PRY BAR AT THE 4X8" CHUTE, UNLOADING ROCK FROM THE CHUTE, ANOTHER ROCK HIT BARTHEN HIT EMPLOYEE'S RIGHT WRIST.

EE WAS TYING REBAR WHEN THE PLIERS SLIPPED OFF THE WIRE AND STRUCK HIM IN THE LOWER LIP.

EMPLOYEE WAS SWINGING A SLEDGE HAMMER WHILE DOING MAINTENANCE IN THE PLANT AND STRAINED HIS RIB CAGE.

LODGED ROCK IN JAW CRUSHER INJURED ATTEMPTED TO DISLODGE ROCK WITH PRY BAR

EE WAS WORKING ON A CRUSHER. HE GOT A PRYBAR STUCK TRYING TO REMOVE A CHIPPING HAMMER. HE COULD NOT GET HAMMER OUT SO HE THREW PRYBAR DOWN ON GROUND. WHEN HE THROW PRYBAR DOWN A PIECE OF METAL WENT INTO TO HIS LEFT EYE. NO SAFETY GLASSES BEING WORN AT TIME.

EE WAS SWINGING A SLEDGE HAMMER TO REMOVE SOME ROCK FROM A TAIL PULLEY. HE WAS STANDING ON ICE GRAVEL, & MUD ON A CONCRETE PAD. HE LOST HIS FOOTING & HIT HIS ELBOW ON A HOOK USED TO HOLD A GU ARD IN PLACE. CONTUSION TO LEFT ELBOW

EE SUSTAINED A SEVERE LACERATION TO HIS FACE WHEN TIGHTENING A BOLT WITH A WRENCH AND IT SLIPPEDSTRIKING HIS FACE.

EE WAS USING A HAMMER, MISSED AND HIT HIS RIGHT INDEX FINGER.

EE WAS SPLICING BELT AND FELT IRRITATION IN RT EYE.

EE WAS STRIKING A SHAFT WITH A SLEDGEHAMMER WHEN A PIECE OF METAL CHIPPED OFF AND EMBEDDED IN HIS ARM.

EMPLOYEE WAS USING HANDSCALING BAR WHEN HE STRAINED HIS RIGHT UPPER BACK AND SHOULDER.

CLEANING BUILD UP AT OF THE 9 HEAD BOX. HIT HIS HAND ON A METAL PLATE WHILE SWINGING A HAMMER.

EE WAS ADJUSTING IDLER ON CONVEYOR WITH HAMMER WHEN HE SWUNG HAMMER AND MISSED, STRAINING HIS BICEP.

EMPLOYEE WAS CLEANING MATERIAL BUILD UP FROM THESPLITTER CHUTERS ABOVE THE SCREEN DECK.

WHILE LINING BEARING BOLT HOLES ON A CONVEYOR WITH A DRIFT PUNCH EE WAS STANDING BY COWORKER TO PUT BOLT IN HOLE. COWORKER HAD THE DRIFT PUNCH IN ONE OF THE BOLT HOLES. THE DRIFT PUNCH SLIPPED OFF OF THE BOLT HOLE AND STRUCK EE UNDER HIS RIGHT NOSTRIL OF HIS NOSE.

EE WAS CUTTING SOME SKIRT RUBBER WHEN KNIFE SLIPPED AND CUT HIS THUMB. THUMB REQUIRED TWO STITCHES.

EMPLOYEE WAS TIGHTENING BOLT WITH A WRENCH WHEN HAND SLIPPED AND STRUCK METAL-LACERATING HAND.

EMPLOYEE WAS CUTTING WIRE WITH A KNIFE, THE KNIFE SLIPPED RESULTING IN LACERATION OF LEFT HAND.

EE WAS ATTEMPTING TO GET A BEARING OUT OF ITS PACKAGING BY HITTING THE BOX WITH A HAMMER. UPON DOIN SO, A FRAGMENT OF METAL SHOT OUT AND STRUCK HIM IN THE RIGHT LEG. IT WAS EMBEDDED IN HIS RIG HT SHIN BONE.

USING A METAL BAR, CLEANING OUT CHUTE, STRUCK HAND ON PIECE OF METAL

EMPLOYEE WAS SHIFTING A PIECE OF RAIL WITH A PRY BAR AND STRAINED HIS LOWER BACK.

USING SLEDGE HAMMER TO CLEAN DUST CHUTE.

EE WAS DRIVING A PIN ON THE BACKHOE TRACK AND A PIECE OF METAL FROM THE PIN WENT INTO HIS SKIN. FOREIGN OBJECT REMOVAL FROM A DOCTOR.

EE WAS CUTTING OLD CONVEYOR BELT WHEN THE BLADE CAME OUT OF THE UTILITY KNIFE CAUSING HIM TO RUN HIS FINGER OVER THE BLADE.

EE WAS CLEANING ROCKS FROM GRIZZLE BARS USING A SLEDGE HAMMER TO BREAK THE ROCKS. A CHIP FLEW UNDER EE'S SAFETY GGLASSES STRIKING HIM IN HIS LEFT EYE

MAINTENANCE ON DRAGLINE.

WAS LIFTING FLOOR WITH HAMMER, HE MISSED AND HIT SIDE OF BOX WITH LEFT ELBOW.

WGUKE CUTTING CONVEYOR BELT WITH UTILITY KNIFE, THE KNIFE SLIPPED AND CUT UPPER RIGHT KNEE.

EE WAS BEATING ON THE KILN DISCHARGE SCREW HOPPER WITH A 10FT PIECE OF HEAVY STEEL. HE HAD BEEN INSTRUCTED TO WAIT UNTIL THE PROPER TOOL HAD BEEN BROUGHT (SLEDGE HAMMER). HE REACHED OVER HIS H EAD AND PULLED A MUSCHLE.

CLEANING MUD FROM DRY FEEDER, PRY BAR BOUNCED BACK AND HIT LEFT SHIN.

TIGHTENING BOLTS