Buscar en el registro

Employee was cleaning up a large amount of spilled dust, sweeping and shoveling approximately 4000 lbs. Noticed a pain in her left hip. Not better on Tuesday, April 2 (her next reporting day). Went to Doctor, diagnosed as lumbar strain.

Employee was splicing telephone wire and employee cut his left hand and required 4 sutures. Employee was wearing gloves and was using the right knife for the job a splicing knife. Employee stated that the knife came loose of the splice and contacted his lift hand.

The employee was using a pipe and a hammer to break up clumps of material in an outside hopper. The employee put one end of the pipe on a clump and went to strike the other end of the pipe. The hammer head glanced off the end of the pipe and the employee's hand that was holding the hammer hit the end of the pipe. The employee broke the second digit on his right index finger.

Employee was installing the ductwork and was tightening down a nut when his ratchet slipped off of the nut. The employee lost his balance and fell backwards. The employee impacted a handrail support that tore through two layers of clothing and left two deep wounds in his upper right thigh.

Employee was assigned the task of removing the liner from a furnace. Castable frefractory had formed around the bottom of liner and employee was using a hammer and chisel to loosen this and also a cum-a-long. Employee got up to get a drink of water when he had a sharp pain in his chest. He was sent to the medical clinic and was given muscle relaxers.

Mechanic was repairing defective links in chain on bucket elevator. He was using a steel punch to unlodge the pins; the steel punch got stuck in the groove and when he jerked it out, the blunt end hit him in the lip. He received 4 stitches on the outside of his lip and 1 on the inside.

Heavy Equipment/Diesel Mechanic with over three years of experience was using a pry bar approximately 5 feet long to straighten a mirror bracket on an end loader. The bar slipped out of the bracket and struck the employee in the lip. Employee's lip was lacerated requiring stitches and lost time away from work.

EE WAS INSTALLING STAINLESS STEEL BANDING ON PIPE. EE WAS GOING TO CUT OFF EXCESS WITH SIDE CUTTERS WHEN THE SIDE CUTTERS SLIPPED, CAUSING EE TO STRIKE HIS RIGHT FOREARM ON THE STAINLESS STEEL BAND - 1 1/2" LACERATION TO THE RIGHT FOREARM.

Two employees were in the process of setting the tension. The other was holding tension on spring with spanner wrench. EE was preparing to put a locking pin which holds spring in place, began to place the pin; wrench broke allowing the spring to release tension. Bolt cut through his glove causing a laceration on right hand in the fleshy area below the thumb. 8 sutures.

While employee was performing a maintenance activity at a height of approx 8 ft, the ee used a retractable tape measure as a pointing device. While pointing at a damaged roller, the tape became entangled resulting in laceration of right index finger, requiring six sutures.

EE WAS TIGHTENING BOLT ON A SCREW. AS WEIGHT WAS APPLIED TO WRENCH IT SLIPPED CAUSING EE TO CUT UNDERSIDE OF RIGHT FOREARM ON BLADE OF SCREW.

EE STRAINED LEFT SHOULDER WHILE USING A "POKE POLE TO DISLODGE KAOLIN CLAY WHICH HAD BRIDGED OVER IN A SHREDDER HOPPER. THE "POKE POLE" IS A PIECE OF 3/4" IRON PIPE ABOUT 10' LONG. IN ORDER TO DISLODGE THE KAOLIN, THE POLE MUST BE LIFTED UP AND DOWN. EE INJURED HIS SHOULDER WHILE DOING THIS.

EE WAS CUTTING A STEEL BAND WHICH HELD THE COVER OVER A BOX OF EMPTY SUPER SACKS. WHEN THE BAND WAS CUT IT SPRANG BACK STRIKING EE S LEFT FOREARM RESULTING IN A LACERATION REQUIRING FIVE STITC HES.

EMPLOYEE WAS REMOVING A BEARING FROM A SHAFT USING A 2# MACHINE HAMME AND 3/4" X 3/8" PUNCH. A SMALL FRAGMENT OF METAL SHEARED FROM SMALL END OF PUNCH, STRIKINGEMPLOYEE IN UPPER LEFT STOMACH AREA. THE FRAGMENT OF METAL EMBEDDE DUNDER THE SKIN AND WAS REMOVED BY THE DR.

HE WAS REMOVING CLAY FROM UNDER A SHAKER SCREEN TO REPAIR A BROKEN ELECTRICAL WIRE WITH A 3' X 1" BAR. WHILE ATTEMPTING TO REMOVE THE CLAY BUILD-UP HE STRUCK HIS RIGHT HAND AGAINST A PIPE CLAM P FROM THE SCREEN REJECT PIPE CAUSING A CUT BETWEEN THE INDEX FINGER AND MIDDLE FINGER.

EMPLOYEE WAS LEANING OVER HANDRAIL CLEANING OUT OVERFLOW TROUGH ON DUST TANK. HAND TOOL HE WAS USING SLIPPED AND MASHED FINGER BETWEEN TOOL HANDLE AND TOP OF DUST TANK.

INJURED WAS TRYING TO TAP A SCREEN IN PLACE WHENHE STRUCK HIS RIGHT INDEX FINGER WITH THE HAMMER

JOEL WAS USING A 2 LB. HAMMER TO BREAK LOOSE THE OUTSIDE SHOES OF THE CRUSHER WHEN A PIECE OF THE HAMMER HEAD BROKE & STRUCK HIM IN THE MIDDLE OF THE FOREHEAD. ON 12-20-93 JOEL REPORTED THAT A PIECE OF METAL MIGHT STILL BE STUCK IN HIS FOREHEAD.

EE HAD TIED 2 SUPER SACKS OF CLAY TOGETHER DOUBLE STACKED ON PALLETS WITH 1/4 INCH SASH CORD. HE WAS IN THE PROCESS OF CUTTING THE EXCESS OF CORD WITH A BOX CUTTER. THE CUTTER SLIPPED ON THE C ORD AND HE CUT THE TOP PART OF HIS LEFT THUMB REQUIRING SIX SUTURES.

EE WAS TRYING TO USE A POCKET KNIFE TO CUT HOLE IN A MUD FLAP HE WAS TRYING TO FIX. KNIFE SLIPPED AND EE CUT HIS RIGHT INDEX FINGER.

EMPLOYEE WAS REMOVING ABOUT 8" OF INSULATION FROM PIPE TO PERFORM WORK ON PIPE. HE HAD CUT AROUND THE PIPE AND DOWN REQUIRED LENGTH AND WAS USING THE KNIFE TO REMOVE INSULATION. KNIFE SLIPPED AND PUNCTURED LEG. REQUIRED SUTURES.

EMPLOYEE WAS CUTTING BAGS TOWARD HIMSELF, BLADE SLIPPED AND HE STABBED HIS FOREARM.

EE WAS WORKING ON 2 FILTER DISCHARGE GEARBOX GUARD. HE WAS CLEANING CLAY OFF AN OLD GUARD WITH A SCREWDRIVER AND SAND GOT IN HIS LEFT EYE. HE WAS WEARING SAFETY GLASSES.

54736YEE WAS REMOVING BOLTS FROLMA PIPE FITTING. WHEN HE REMOVED THE LAST BOLT, PIPE CAME UP HITTING HIM IN UPPER LIP.

54730USING 8 LB HAMMER TO REMOVE TAPE BUSHING ON SLICER-SPEED-REDUCER SHAFT. EMPL STRAIN BACK DURING THIS PROCESS OF REMOVING BUSHING.

WHILE REMOVING PILLOW BLOCK BEARING FROM IDLER SHAFT ON DRAG BOX USING A HAMMER AND COLD ROLL PUNCH, APIECE OF THE BEARING CAME OFF HITTING INJURED IN THE LEFT CHEEK.FOREIGN BODY REMOVED -SUTU RES REQUIRED.

CUT HAND WHILE CUTTING PLASTIC VACUUM LINE WITH RAZOR KNIFE.

EE AND ANOTHER EE WERE GOING TO TURN A BEARING HOUSING WHICH WAS IN A VICE. HE LOOSENED THE VISE TO TURN THE HOUSING AND IT SLID DOWN ONTO HIS LEFT INDEX FINGER CAUSING ALACERATION.

WHILE REPAIRING TANK CAR DOEM LID BOLT AND NUT, HE USED 18" PIPE WRENCH. WRENCH SLIPPED, HIT NEXT BOLT AND THEN HIT AND CUT EMPLOYEE'S RIGHT WRIST, REQUIRING SUTURES.

EMPLOYEE CUT LEFT WRIST WHILE CUTTING TOP OUT OF A 5 GALLON PLASTIC BUCKET. THE KNIFE SLIPPED, CAUSING EMPLOYEE TO CUT HIS WRIST.

USING A 24" PIPE WRENCH TO TAKE APART A 2" PIPE UNION.SMASHED LEFT LITTLE FINGER BETWEEN A WRENCH AND A BASKET.

KNOCKING SLIDE BACK ON ROCK CHUTE FOR THE RAYMOND MILL. WAS USING A 20# SLEDGE HAMMER. HIS HAND WAS SWEATY. HANDLE SLID DOWN BETWEEN HAND, SMASHING TIP OF RIGHT INDEX FINGER.

A ROCK FELL OUT OF THE ELEVATOR HE WAS WORKING ON AND HIT HIM IN THE MOUTH CHIPPING HIS TWO FRONT TEETH.

OPENING SLIDE GATE UNDER THE UNIT 3 ROCK DUMP WITH A SLIDE HAMMER WHEN FINGER GOT BETWEEN THE SLIDE BAR AND THE END OF SLIDE HAMMER.

EMPL BUMPED RIGHT WRIST ON TOTE BIN WHILE CLEANING LOOSE CLAY FROM UNDER MILL. HE WAS USING SHOVEL TO MOVE CLAY.

EMPL TIGHTENING DOME BOLTS ON TANK CAR USING BOTH HANDS ON 18" ADJUSTABLE WRENCH.WRENCH SLIPPED PINNING LEFT THUMB AGAINST DOME PLATFORM.

LIFTED 2 SHEETS OF HEAVY METAL USING IRON BAR BAR SLIPPED STRAIGHTENED BACK AND FELT PAIN IN LOWER BACK

BAGGER CHAIN BROKE WHILE TIGHTENING CHAIN NUT BOLTS WITH WRENCH SLIPPED AND POPPED UPWARD HITTING FACE AND THE BRIDGE OF NOSE

HE WAS IN PROCESS OF CUTTING AND FITTING CARDBOARD PATTERN FOR SHORT AUGER BEING INSTALLED FROMC ATWALK TO INSIDE OF IRON SULFATE DRYER. HE WAS LAYING DOWN ON CATWALK IN ORDER TO REACH UP UND ER AUGER. NEEDING TO TRIM MORE OFF OF PATTERN HE SAT UP AND PROCEEDED TO TRIM CARBOARD AT WHICH TIME RAZOR KNIFE SLIPPED AND HE CUT UPPER OUTSIDE OF RIGHT THIGH.

SQUATTED DOWN TO TIGHTEN UP BOLT ON SPRINGS OF DUMP TRUCK

I NAME WAS MOUNTING A MOTOR VERTICAL ON THE TURBINE WHIZZER AT MILL #2 HE WAS HOLDING IT UP WITH A COMALONG HE HAD TOLIFT ONE SIDE OF THE MOTOR TO ALINE THE BOLTS AND STRAINED HIS BACK

I NAME WAS CUTTING A PIECE OF 3/16" THICK RUBBER USING A PIECE OF STEEL AS A STRAIGHT EDGE THE KNIFE SLIPPED AND CUT HIS L THUMB AND REQUIRED STITCHES

EMPLOYEE CHECKED A LEAK IN AN ALUM LINE AND THOUGHT A NIPPLE AT A VALVE WAS LEAKING. HE STARTED TO TIGHTEN THE NIPPLE AND THE REDUCING BUSHING THE NIPPLE WAS SCREWED INTO CAME APART. ALUM BLEW OUT ONTO HIS CHEST AND FACE GETTING INTO HIS EYES. HE WAS WEARING SAFETY GLASSES AT THE TIME.

EMPL WAS REPLACING A BEARING IN THE PALLETIZER ELEVATOR HE OVEREXERTED WHILE PULLING ON A CROWBAR TO LINE UP BOLT HOLES NOTE DR ON 10/18/89 PRESCRIPTION

HE WAS CHANGING OIL IN #36 TRACTOR. WRENCH SLIPPED OFF OIL PLUG AND HIS RIGHT HAND HIT SOMETHING ON ENGINE AND CUT MIDDLE FINGER ON RIGHT HAND, REQUIRING 5 SUTURES.

USING SLEDGE HAMER TO FLATTEN ENDS OF IRON PIPE PIPE BING USED TO BUILD HANDRAILS PULLED R SHOULDER WHILE SWING ING HAMMER

THE INJURED WAS WELDING CLOSE TO THE FLOOR AND WAS LAYING ON THE FLOOR.HE WAS CHIPPING OFF THE SLAG AND A PICE WENT BEHIND HIS SAFETY GLASSES AND BURNED HIS LEFT EYE LID.DID NOT GO TO DOCTOR T ILL 05-31-89,CHANGED TO MEDICAL TREATMENT 05-31-89.

EMPL USING BANDING TOOL TO ATTACH RUBBER HOSE TO FITTING.END OF BAND WAS STICKING OUT OF TOOL.WHEN EMPL TURNED HANDLE OF TOOL HAND SLIPPED AND HIT SHARP END OF BAND CUTTING RIGHT THUMB.EMPL WA S WORKING FROM BOAT IN WASTE POND.

I.NAME WAS REMOVING A PLASTIC LID FROM A 5 GALLON PLASTIC PAIL. WHEN USING A POCKET KNIFE TO CUT THE LID FOR REMOVAL WITH A PRY TOOL THE KNIFE SLIPPED AND SLIT THE MIDDLE FINGER ON THE LEFT HA ND REQUIRING SUTURES.

I NAME AND ANOTHER EMPL WERE AT THE IRON SULFATE PLAN REMOVING AN AUGER THE SHAFT WAS STUCK AND I NAME WAS USING A PIPE WRENCH TO ROTATE THE SHAFT TO LOOSEN IT SO IT COULD BE REMOVED THE PIPE WRENCH SLIPPED LOOSE AND I NAME FELL BACKWARDS AND LANDED ON HIS L LEG