Buscar en el registro

EE WAS REASSEMBLING A BROKEN SANDLINE IN QUARRY. WHILE TIGHTENING BOLTS ON FLANGES, HE SLIPPED AND FELT PAIN IN HIS RIGHT GROIN AREA.

EMPLOYEE WAS ON BREAK, EATING LUNCH. HE WAS CUTTING ASAUSAGE WHEN THE KNIFE SLIPPED AND PUNCTURED HIS LEFT HAND. FOUR STITCHES WERE REQUIRED.

EMPLOYEE WAS CLOSING THE BOTTOM DOOR ON A RAIL CAR. THE DOOR WAS HARD TO CLOSE AND HE WAS USING A LONG TRACK BAR TO PULL THE DOOR CLOSED. WHILE PULLING ON THE BAR, HE FELT A PULL IN HIS LOWER BACK.

EE WAS CUTTING EXPANDED METAL AND CUT HIS INDEX FINGER ON THE EDGE OF THE METAL. STICHES WERE REQUIRED FOUR.

THE EMPLOYEE WAS LAYING ON THE GRATING BY THE DREDGE PUMP TO TIGHTEN THE BOTTOM CASING BOLTS. HE WAS PUSHING THE WRENCH IN AN UPWARD DIRECTION WHEN HE PULLED A MUSCLE IN IS NECK. HEAT PADS AND MEDICATION WERE REQUIRED TO RELIEVE THE STIFFNESS.

WHILE TRYING TO MOVE A SAND CAR BY USING A RAIL CAR JACK. EE STRAINED HIS BACK.

EMPLOYEE WAS USING A NAIL PULLER TO REMOVE NAILS FROM SIGN BOARDS. NAILS WERE AT HEAD HEIGHT. NAIL HEAD BROKE OFF AND PULLER STRUCK EMPLOYEE IN UPPER LIP.

EMPLOYEE WAS WORKING ON A RAILCAR TO UNJAM A DOOR WHEN HE STRAINED HIS STOMACH.

EMPLOYEE WAS TIGHTENING A DRILL BIT WITH A DRILLCHUCK. THE CHUCK SLIPPED AND HE STRUCK THE BIT WITH HIS FINGERS. HE CUT HIS MIDDLE FINGER REQUIRING FOUR STITCHES.

THIS IS REOCCURENCE OF AN OLD INJURY. HE WAS SWINGING A 3# HAMMER TO UNPLUG A PIPE. HE HIT A GLANCING BLOW AND CAUSED A PROBLEM WITH HIS NECK AND BACK.

EE WAS USING A CHISEL AND HAMMER TO CUT THE HEAD OFF OF A SMALL BOLT. A SLIVER OF METAL STUCK HIS LEFT ARM ABOVE THE ELBOW IN THE MUSCLE AREA. NOTE: I WAS UNAWARE OF STITCHES UNTIL SEPT. 29, 1 994.

WHILE WORKING IN AN ELECTRICAL BOX THE WRENCH SLIPPED & CUT KNUCKLE RT HAND

EE WAS HELPING A CREW WORK ON 5 MILL TWO SCREW JACKS ARE USED UNDER A SADDLE OT LIFT THE MILL IN ORDER TO POUR THE BEARINGS. HE WAS WORKING ONE JACK WHILE ANOTHER EE WAS ONT HE OTHER JACK. WHE N LIFTING THE MILL IT TAKE 100 TO 150 LBS OF PULLL OR WEIGHT TO OPERATE THE JACK UNDER THE LOAD.

WHILE TIGHTENING A 4" PIPE BUSHING WITH A 36" PIPE WRENCH, THE WRENCH SLIPPED AND STRUCK EMPLOYEE IN THE RIB AREA, RIGHT SIDE.

HE WAS TIGHTENING BOLTS ON FLANGE TO LINE FROM ATTRITION CELL PLATFORM TO GALIGHER SUMP BOX WHEN THE RATCHET SLIPPED AND HIS MOUTH HIT THE FLANGE KNOCKING OUT HIS FRONT TOOTH. HE WAS SITTING O N A PIPE AT THE TIME.

SWINGING A SLEDGE HAMMER AND FELT PAIN IN LOWER BACK.

EE WAS TIGHTENING THE BRAKE ON A RAILCAR BY TURNING THE BRAKE WHEEL HIS RIGHT HAND SLIPPED OFF THE BRAKE WHEEL STRIKING AGAINST A STEEL SUPPORT DIRECTLY BEHIND THE BRAKE WHEEL CAUSING A STRAIN TO HIS RIGHT WRIST.

WAS PERFORMING ROUTINE DUTIES. OPENING SLIDE ON BOTTOM OF RAILCAR WITH TRACK BAR AND THE BAR SLIPPED OUT. HE HIT HIS HAND ON RAILROAD TIE AND BENT THUMB (RIGHT) BACKWARDS.

EMPLOYEE WAS CUTTING A NYLON STRAP, FOR PAKCING WITH A STRAIGHT KNIFE. THE KNIFE SLIPPED AND CUT HIM ON THE INDEX FINGER.

WHILE TIGHTENING A FITTING ON A DUST LINE THE PIPE WRENCH SLIPPED AND SMASHED HIS THUMB.

EMPLOYEE WAS CLEANING UP WASTE MATERIAL AROUND THE CALCINE BAGGING MACHINE AT SMALL BELT. WHILE SHOVELING, HE CAUGHT RIGHT FINGER BETWEEN THE SHOVEL HANDLE AND THE GUARD CUTTING HIS LITTLE FIN GER AND NAIL. STITCHES WERE PUT IN THE FINGER AND 1/2 OF THE FINGER NAIL WAS REMOVED.

EMPLOYEE WAS WORKING ON D8K TRACK LINK IN SHOP.WHEN TRYING TO PUT TOGETHER,HE WAS HOLDING PIECE TOGETHER AND ANOTHER EMPLOYEE WAS USING A HAMMER.IN DOING SO HE HIT INJURED'S HAND.THE RIGHT THU MB WAS CONTUSED AND FRACTURED.

54736YEE WAS USING A 6' LONG PRY BAR TO LIFT A DART VALVE.WHEN REMOVING TIRE BAR HE STRUCK HIS RIGHT ELBOW ON A HANDRAIL.

EMPLOYEE WAS REMOVING A BEARING FROM A PUMP SHAFT WITHA COLAD CHISEL AND HAMMER. A PIECE OF STEEL FLEW FROM EITHER THE BEARING OR THE CHISEL AND STRUCK THE EMPLOYEE UNDER THE LEFT EYE.

A CHIP OF CHISEL HEAD IMBEDED IN THUMB ON LEFT HAND WHILE HITTING CHISEL WITH HAMMER.

BUCKET CAME OFF ELEVATOR.PLUGGED UP THE CHUTE.HE TOOK A BROOM HANDLE AND PULLED UP TO THE SIDE DOOR AND PULLED IT OUT.

EE WAS REPLACING PIN ON CENTER SHAFT WHILE TIGHTENING BOLT THE WRENCH SLIPPED, HITTING HIS LEFT HAND CAUSING HIS FINGE TO SWELL. ICE WAS APPLIED. EMPLOYEE DID NOT WANT TO GO TO DOCTOR. ON 4-10 -91 EMPLOYEE REQUESTED TO GOT TO DOCTOR, AFTER X-RAYED IT WAS FOUND TO BE FRACTURED.

EMPLOYEE WAS STRIKING A 8" PIPE WITH A 3# HAMMER BECAUSE IT WAS PLUGGED. HE SWUNG ANDHIT A GLANCING BLOW ON THE PIPE WHICH HE FELT CAUSED A PROBLEM WITH HIS NECK. AND SHOULDER.

EMPLOYEE WAS HELPING ROLAND'S ROAD SERVICE MECHANICS REPAIR THE TRACK ON A KOMATSU BULLDOZER.THE SERVICE MECHANICS WERE DRIVING A CENTER PIN THROUGH THE TRACK TO FASTEN THE TRACK,WITH A SLEDGE HAMMER WHEN A PIECE OF METAL SHEARED FROM THE PIN AND STRUCK THE EMPLOYEE ON HIS LEFT LEG BELOW THE KNEE CAP.THE METAL PUNCTURED AND STUCK IN EMPLOYEES LEG.

RIGGING ON HOPPER SLIPPED RESULTING IN THE HOPPER FALLING ON THE EMPLOYEE'S HEAD.

WHILE USING A COME-A-LONG TO LOWER AN EXHAUST FAN THE CABLE SLIPPED CUT OF THE HOOK HOLDING IT AND THE COME-A-LONG STRUCK HIM THE MOUTH. A PARTIAL PLATE WAS BROKEN IN HIS MOUTH.

EMPLOYEE WAS USING WIRE BRUSH PREPARING STEEL FOR PAINTING. STRUCK FINGER ON SHARP EDGE OF STEEL THAT WAS NOT GROUND OFF. CUT INDEX FIGNER OF RIGHT HAND.

EMPLOYEE WAS SHOVELING UP A SAND SPILL WHEN HE STRUCK HIS KNEE THIS CASUSED HIM TO FALL BACKWARD & THE SHOVEL HANDLE STRUCK HIS THUMB A LIGHT BULB WAS BURNT OUT & TH4E EMPLOYEE DID NOT SEE A M ETAL BEAM THAT HE STRUCK THE SHOVEL ON AT THE TIME OF THE ASCCIDENT THE EMPLOYEE WAS TAKEN TO THE DOC HE WAS DIAGNOSED CONTUSION TO THE KNEE & A SPRAINED THUMB A FOLLOW UP VISIT WAS ON 05-11-

WORKING WITH COME A LONG, PUTTING IMPELLLOR UP ON PLATFORM L SHOULDER SLIPPED OUT OF JOINT AND THEN SLIPPED BACK

EMPL WAS DISLODGING BOULDERS IN CRUSHER HOPPER WITH PRY BAR & PULLED MUSCLE IN SHOULDER.

HELPING CREW WORK ON MILL 5. SCREW JACKS USED UNDER SADDLE TO LIFT THE MILL IN ORDER TO POUR BEARINGS WORKING ONE JACK WHILE ANOTHER EMP ON OTHER JACK LIFTING THE MILL IT TAKES 100 - 150 LBS O F PLL OR WT TO OPER JACK UNDER THE LOAD

EMPLOYEE IRRITATED SHOULDER MUSCLES BY TIGHTENING BOLTS IN AN AKWARD POSITION FOR A LENGTHY PERIOD OF TIME.

EE STATED THAT HE WAS TIGHTENING A NUT AND HIS WRENCH SLIPPED, CAUSING HIM TO LOSE HIS BLANACE HE THEN FELT A SHARP PAIN IN HIS LOWER BACK.

INSTALLING SEAL STRUCK HIS FINGER W ITH HAMEMR DURING PROCESS. INCURRED FRACTURE TO L FOREFINGER DISTAL

2 EMPL WORKING TOGETHER.ONE WAS POUNDING RUBBER LINING IN PLACE,ONE WAS ASSISTING.ONE JPLACED HAND ON LINING TO CHECK FIT AT SAME TIME THE OTHER EMPL STRUCK LINING WITH HAMMER.

EMPLOYEE WAS IN AWKWARD POSTION WHILE REASSEMBLING PUMP.HE STRAINED HIS SHOULDER AND BACK WHEN HE TIGHTENED HOUSING BELTS.

EMPLOYEE WAS REPAIRING A 5 MICRON SEPARATOR THE WRENCH SLIPPED CAUSING HIM TO JAM THE SHARP POINT OF AIR VALVE IN HIS RT HAND BELOW THE KNUCKLE

EMPLOYEE WAS REPLACING A TAIL PULLEY BARING HE APPLIED HEAT AND WAS STRIKING WITH A HAMMER WHEN A METAL PIECE BROKE LOOSE

EMPLOYEE WAS HITTING BOARD WITH HAMMER BOARD SLIPPED HAMMER FLEW OUT OF HAND CLAWS ON HAMMER STRUCK EMPLOYEES FOREHEAD CAUSING LACERATION 3 SUTURES REQUIRED

TAKING OFF NUT ON REVERSING VALVE WHEN HUT BROKE LOOSE RT THUMB HIT STORAGE CABINET

EMPLOYEE WAS US3NG A PRY BAR TO INSTALL A CHAIN ON A 623B SCRAPER.THE BAR SLIPED AND STRUCK EMPLOYEE ON CHEEKBONE NEAR HIS EYE.

EMPLOYEE WAS LOOSENING BOLT. WRENCH SLIPPED OFF BOLT. EMPLOYEE FELL BACK AND HIT RIGHT ELBOW ON A FLANGE.

EMPLOYEE WAS HO5DING PIPE WRENCH AS ANOTHER EMPLOYEE TURNED A BOLT. THE PIPE WRENCH SLIPPED.

EMP WAS POUNDIN1 IN FENCE POSTS AND PINCHED HIS FINGER BETWEEN THE DRIVER AND THE POST

THE EMPLOYEE WA8 REMOVING THE LOWER SEAL FROM THE TRUNNION HOUSING ON #6 MILL.CHANNEL LOCKS SLIPPED AND STRUCK HIM IN THE CHIN CAUSING A LACERATION THAT REQUIRED 3 STITCHES.