Buscar en el registro

Employee was using a grinder and slipped and lost balance while grinding. Employee received an injury to right index finger which required 3 stitches.

Maintenance employee was rebuilding a pump, using an impact gun and noticed pain in EE's right wrist/hand.

Employee was on a Vermeer walk behind machine performing clean up tasks in the wet plant area of Utica 3. EE was pulling material out near the surge bin when a finger became wedged between a pipe and the toggle on the machine controls. EE sustained a fracture on the left hand ring finger tip.

While using a grinder, a maintenance mechanic received a laceration on the thumb when the disc caught the bolt being cut and kicked back into EE's left hand, cutting through the leather glove EE was wearing.

Employee ran into parked railcars while operating a trackmobile. EE was thrown from the seat which resulted in a fractured nose and fractured sternum. Contributing factors to the incident were inattention and the employee failed to wear the seatbelt.

Employee was thawing out bridged material above BC-107 and a large piece broke off. Employee pulled the torch back that EE was running and in doing so twisted shoulder. Required no medical attention at the time. 8 months after the incident EE was having issues with the shoulder and went to the doctor for an examination.

Maintenance employee was fabricating mounting bracket for oxy/acy. cylinders to be mounted upright in new Ford shop truck. A pipe hanger was being modified into a mount when the S.S. Disk on grinder became entangled with uniform shirt pulling itself into their lower right abdomen, resulting in a laceration needing 8 sutures at ER.

An Employee was drilling a bracket with left hand and a drill with right hand when the drill bit snagged spinning the bracket around into Employee's palm. The spinning action resulted in the latch ripping through Employee's leather glove and into the tissue in Employee's palm. The Employee was taken to the hospital to get checked and ended up receiving 3 stitches in hand.

While hoisting an unloaded electric chain hoist to move it out of the way, the hoist hook briefly caught/bound on a piece of machinery, popped loose, and struck the worker in the lip causing a laceration. Both upper front teeth were also chipped along the inner edge.

Employee was grinding with hand held grinder wearing safety glasses and face shield. The next day employee's eye felt irritated employee went to the clinic and they removed a small piece of metal, employee received ointment prescription for eye. Employee did not miss any time.

Employee was operating the scraper when ee hit a pot hole and felt a sharp pain in back. Employee called the supervisor and notified ee of the incident. The employee was taken to the clinic where ee was diagnosed with acute lower back pain. Employee was given prescription medication and restrictions.

While using an angle grinder the grinder kicked back hard enough to come loose from the operators left hand and the cut off wheel nicked left thumb as it passed. This resulted in a minor cut between the first and second knuckles of the left thumb which was repaired with 3 stitches. The operator returned to work and finished shift with no restrictions from the doctor.

Employee was holding angle for welder to tack up in hopper. From 11:30PM to 6AM. Employee was closing eyes as welder was welding. Employee went home and woke up with burning eyes.

Employee was cutting steel with angle grinder. Steel was not supported properly and pinched cutting wheel. Cutting wheel disintegrated with debris reaching employee's eye despite dual eye PPE. Debris was removed by doctor and employee was returned to regular work

Employee was welding and grinding and felt irritation in his right eye. He was wearing all necessary PPE but conditions were windy and work was occurring on the floor above. A small piece of metal was removed by the eye doctor and a prescription antibiotic was given.

Employee was cutting a door on the RTO in half to create a safer access into the exhaust plenum. While cutting the door using a 4" grinder, the grinding wheel got bound up and kicked back striking the employee in the left forearm. The employee suffered a laceration on his arm which required 11 stitches to close.

Employee tried to clean shavings off of a drill bit that was in a running drill press. The drill bit then got tangled with his glove and wrapped his left hand up in the drill bit thus, dislocating his left index finger.

EE operating excavator-back pain at lunch, told FM, but didn't know what happened worked to end of shift, came in Monday 11/17/14 - wanted to seek medical attention - taken to clinic as precaution.

EE was using a 4 1/2" grinder with wearing gloves, the grinder also did not have a guard on it and he was not wearing the required PPE to protect his eyes. He ended up injuring his finger / requiring stitches - he was suspended for 3 days.

Employee was holding a piece of sheet poly in place as another person was drilling a hole in it to bolt it in place. The bit nicked his arm causing a cut.

Employee was helping two welder repair crusher during a schedule shutdown. The EE was exposed to the light from the welding operation that was going. The EE had the access to the correct PPE but chose not to wear it. The EE was seen by the local Dr on 11/22/13 and giving perspiration medicine for his eyes. The EE is doing fine and returned to work the same day.

Injured employee was pushing bottom of a bolt up with hand during removal of a loader bucket cutting edge. Bolt was not fully inserted into the square catch of the cutting edge. A second employee using an impact wrench on the nut started and the bolt turned, cutting the right hand and finger of injured employee. Employee required 15 stitches to close the wound.

Employee was using a grinder to cut a 12" piece of angled steel, when the angle started to move he removed his left hand from the handle of the grinder and proceeded to use his hand to hold the angle in place instead of a vise or clamp. At this point the grinder got bound up causing the grinder to jump and hit the employee on his left hand/thumb area leaving a laceration.

EE was welding and a piece of metal got into his eye.

On 04/17/2012 at approximately 8:15 am. EE was allegedly lifting up on the diffuser bar on the VS302 and he felt pain and a pop in his right shoulder. He was taken to the hospital for medical evaluation and was given an X-Ray that was negative for breaks and other signs of trauma.He had a medical procedure on 05/30/2012 that made this incident MSHA reportable.

Work was being done to remove a section of the railroad track, two excavators were in use. Excavator #1 moved into position and was directed to stop. Excavator #2 mirrored movement of excavator #1 without direction and because it did not stop as it should have, it pulled the rail towards itself and struck the leg of employee.

Employee was in a JLG boom lift. As he moved to the left the boom dropped. Employee lost balance and had his foot caught in the pedal housing causing a dislocation of right ankle and fracture of 5th toe

The employee was using a table saw to cut pieces of PVC blocks. With the saw running, he reached under it, and his right middle finger was struck by the rotating blade. He sustained a laceration and damaged distal phalanx bone. Prior to the task the supervisor had a meeting with the three employees that were assigned to do the task about the safety issues with the job.

Employee was grinding welds with a grinder while wearing safety glasses and a full face shield. It appeared some of the grind must have bounced off the metal wall behind him and entered from the side.

EE was using a hand grinder with a cutting wheel when he was struck in the eye with a piece of debris. The EE was taken to a doctor where no damage was found.

Putting an agitator in place. Lifting with a winch and shaft of agitator moved. The employee grabbed the shaft to control it and it yanked his left arm.

Employee was operating a boom truck when the auto kick out on cable got in a bind. When he attempted to free the auto kick out it slipped and mashed his left ring finger.

EE was using a wire brush attached to a power drill to clean teeter pipes. His left glove became entangled in the chuck attachment while operating the tool and twisted his thumb. The thumb was bruised and suffered some ligament damage.

Employee was greasing equipment with a pressure grease gun. The hose on the grease gun failed (pin hole in hose) and injected grease into employees right index finger

EE was cleaning clogged kaolin out the #6 roller mill feed bin. As he was removing the clay from the interior wall, he mashed his finger against the door of the feed hopper. This resulted in a laceration and a broken finger tip on his left ring finger.

While lifting a jaw crusher toggle block, an electric hoist chain swung and mashed a maintenance mechanic's left thumb against a nearby beam of the crusher frame. The mechanic was guiding the block through the frame when the block cleared the jaw and swung free. The incident resulted in a laceration requiring 9 stitches, loss of thumbnail and broken tip of the bone.

A Front End Loader Operator was greasing his loader at the end of his shift. He was at the grease shed using a pneumatic grease gun to do this. The grease gun slipped off the zerk and the grease came out at extremely high pressure which cut into his left thumb.

The employee was replacing a sleeve on a rotating screen when he cut his hand on the feed cone. The feed cone had become very sharp due to normal ware.

Two employees were welding inside of a loader bucket when one of the employees received flash burns to his eyes.

The miner was attempting to loosen the bar bolts on a chainsaw when the bar wrench handle broke and the miners' hand struck the chainsaw chain which cut through his glove and cut the middle finger on his left hand.

BUCKET ELEVATOR BELT BROKE AND FELL. A CRANE WAS USED TO LIFT THE BELTING AND RE-LOOP IT OVER THE HEAD PULLEY INTO HOUSING. EMPLOYEE DIRECTING THE CRANE USED NYLON STRAP AS A CHOKER. WHEN THE BELT HAD BEEN LIFTED 30 FT THE NYLON STRAP PINCHED THROUGH BELT CAUSING IT TO FALL. THE EMPLOYEE GUIDING THE BELT WAS STRUCK IN THE HARD HAT AND BACK BY THE BELTING AND BUCKETS.

The employee was attempting to break a rock that was plugging the front of a feeder going into the primary crusher using a jackhammer. When the jackhammer broke through the rock, the operator lost control of the hammer causing the hammer to pinch his thumb between itself and the guardrail.

Employee was putting a bag on the bagger discharge spout. The bag got caught on a burr on the spout. He reached around the spout at an awkward angle to pull the bag off and felt pain in his right shoulder. He was taken to a doctor and placed on light duty.

During inspection of dust collector baghouse, employee got dust in left eye. Employee was wearing proper PPE provised for performing this procedure. Employee was wearing half mack respirator nstead of full face respirator provided. *Accident not reported until 8/19/08.*

Employee was replacing the bolts on the cutting edge of the dozer blade. The round, flush mount bolt rotated as it was engaged by the pneumatic impact wrench causing a laceration to the employees left index finger.

Employee was cutting expanded metal for guard and jammed his thumb into the metal causing a laceration.

Employee was welding the edges of a roll crusher, while adjusting his welding hood he exposed himself to welding flash from surrounding equipment.

Employee was cleaning a wet scrubber drain using a rotary drain cleaner when the cutting edge encountered hard mud causing the cleaning coil to twist striking the empolyee on the tip of his left ring finger, fracturing the end digit.

Employee had cut off the air to the bagger and locked it out before he began to tighten a plate on it. While tightening the plate, he had his finger in the pinching mechanism and pushed the button to activate it at the same time. The pinching mechanism cut the tip off his middle finger on his right hand (flesh only - no bone involved).

EE WAS CHECKING BEARINGS ON THE #6 DRYER. HE BRUSHED SOME SAND OFF OF A BEARING WITH HIS RIGHT HAND. WITH THIS MOTION, HE CONTACTED THE DRIVE BELT AND PULLEY. THE MIDDLE FINGER OF HIS RIGHT HAND WAS CAUGHT BY THE PULLEY, BREAKING THE BONE AND CUTTING THE TIP OF THE FINGER.