Buscar en el registro

EE WAS CUTTING RUBBER WITH A RAZOR KNIFE WHEN KNIFE SLIPPED AND CUT HIS LEFT HAND ABOVE THE LEFT THUMB.

EES WERE ATTEMPTING TO UNCHOKE #2 CLAY SILO BY USING A PRYBAR & HAMMER WHEN EE STRUCK BAR WITH HAMMER A FOREIGN OBJECT FLEW INTO HIS LEFT EYE.

EE WAS SWINGING A 16 LB SLEDGEHAMMER ON AN UNEVEN SURFACE WHEN HE TWISTED HIS RIGHT KNEE.

EMPLOYEE WAS TRYING TO BEND A BAR BY WEDGING IT BETWEEN 2 STATIONARY OBJECTS. THE BAR BENT SOME AND THEN THE BAR SLIPPED AND HIT HIM IN THE FACE. RIGHT SIDE OF UPPER EYE.

TWO EES WERE REMOVING LINER BOLTS FROM AN FLS BALL MILL WITH A HAMMER AND PUNCH. HAMMER WAS DEFLECTED BY AN ADJACENT HAND RAIL. INJURED WAS STRUCK BY HAMMER ON TIP OF RH MIDDLE FINGER REQUIRIN G APPROXIMATELY 20 STITCHES.

EE WAS USING A PRY BAR TO OPEN A VALVE TO SILO. WHILE APPLYING SUBSTANTIAL PRESSURE, EE STRAINEDHIS RIGHT SHOULDER.

HE WAS TRYING TO SAW A BLOCK OF WOOD TO PROP UP A PRINTER HOOD. THE SAW SLIPPED AND LACERATED HIS THUMB.

SHOVELING TAIL PULLEY OF CONVEYOR. IMPOPER FOOTING. FELT STRAIN IN LOWER BACK.

EE WAS SWINGING SLEDGE HAMMER, FAILED TO CONNECT WITH TARGET AND OVEREXTENDED LEFT WRIST RESULTING IN A SPRAIN.

RATTLING BOLTS ON THE IRON ON TOP & TWISTED BACK

EE WAS USING PRY BAR ATTEMPTING TO UNCHOKE CHUTEWHEN PRY BAR SLIPPED SMASHING FINGER AGAINST CHUTE

CREW WAS CLEANING MATERIAL FROM #2 CLINKER COOLER GRATES. A CHUNK OF BRICK/CASTIBLE FELL OFF WALL OF KILN HOOD AND HIT EMPLOYEE ON HARD HAT.

WHILE CHANGING OUT BELT CLIP, EMPLOYEE USED A HAMMER AS A BACKING AND HIT CLIP WITH OTHER HAMMER, CAUSING SOMETHING TO FLY AND STRIKE HIS LEFT EYE.

EE WAS REPAIRING PUMP. THE HANDLE ON RUBBER HAMMER HE WAS USING TWISTED. THIS RESULTED IN HIS FINGER BEING PINCHED ON A PIECE OF METAL. RIPPED OFF NAIL OF LEFT MIDDLE FINGER AND CUT TO BONE.

INJURED WAS HANGING REBAR INSIDE DOME...IN MAN-BASKET OF P&H 50 TON CRANE. THE GROUND UNDER CRANES LEFT FRONT OUTRIGGER SUBSIDED AND THE CRANE LURCHED FORWARD, CAUSING BASKET TO EE UP AND DOWN . INJURED STRUCK HIS FACE ON STACK OF REBAR IN BASKET.

EMPLOYEE WAS PULLING ON A PIPE WRENCH TO FREE A PUMP RUNNER. WHEN THE RUNNER BROKE FREE, THE RESULTING JOLT INJURED EMPLOYEE'S SHOULDER.

EMPLOYEE WAS USING BAR AND SLEDGE HAMMER TO REMOVE BUILD-UP FROM ISNIDE A PREHEATER VESSEL. HAMMER HIT BAR A GLANCING BLOW RESULTING IN FINGER BEING PINCHED BETWEEN HAMMER HANDLE AND AIR BLAS TER.

EE WAS HITTING SEPARATOR WITH 12 LB HAMMER SEPARATOR WAS PLUGGED.

EMPLOYEE WAS REMOVING GRINDING BALLS FROM BALL MILL SCREENS USING A PRY BAR AND HAMMER. HE WAS STRUCK IN LEFT EYE BY BALL WHEN HE HIT IT WITH HAMMER. FROM ALL INDICATIONS, HE WAS NOT WEARING PPE (SAFETY GLASSES OR GOGGLES).

EE WAS USING A SLEEVER BAR TO BREAK STEEL BAND ON PALLET. AS BAND BROKE, EE STUCK SELF IN (L) FOREARM WITH SHARP END OF SLEEVER BAR.

EMPLOYEE WAS INSTALLING BOLTS IN SLIP FLANGE OF SCREW CONVEYOR. AS HE WAS TIGHTENING THE BOLTS WITH A WRENCH, THE UPPER CONVEYOR'S WEIGHT SHIFTED, CAUSING THE SLIP FLANGE TO COLLAPSE, PINCHIN G EMPLOYEE'S LEFT HAND.

EE WAS ADJUSTING KILN BULL GEAR WITH HAMMER WRENCH & 4# HAMMER AND STRUCK LITTLE FINGER WITH HAMMER.

IMPROPER PLACEMENT OF HAND - BUILDING WOODEN FORMS USING HAMMER & NAILS TO SECURE WOOD.

EE WAS REMOVING SHIMS FROM A WOODEN CONTAINER CUT HIS FINGER ON LOOSE S41M.

EE WAS ASSISTING IN THE INSTALLATION OF DUST COLLECTION CHUTE FOR K-1152 AS THE CHUTE WAS BEING LIFTED IT CAME OFF THE COME-ALONG HOOK AND FELL ABOUT 8' TO THE DECK BELOW. AS THE CHUTE FELL, T HE FLANGED END CONTACTED EE'S (L) FOREARM, CAUSING A LACERATION.

EE WAS SWINGING A HAMMER WHEN IT BOUNCED BACK FROM THE WORK AND STRUCK HIM THE FOREHEAD.

EE WAS ATTEMPTING TO REMOVE A ROCK THAT WAS LODGED BETWEEN THE DUAL WHEELS ON THE MACK WATER TRUCK. HE FIRST USED A PRY BAR TO TRY TO REMOVE THE ROCK AND WAS UNSUCCESSFUL. HE THEN TRIED TO BRE AK THE ROCK WITH A HAMMER. THE TIRE BLEW WHEN HE STRUCK THE ROCK WITH THE HAMMER AND IT THREW THE HAMMER OUT OF HIS HAND AND SENT HIM HURTLING APPROX 8'. BREAKING HIS THUMB, REQUIRING SURGERY

EE WENT TO CLEAN CHUTE THAT STOPPED UP AT 610 PLANT EE WAS USING A BAR (METAL BAR APPROX 6'LONG APPROX 15LBS IN WT ONE END IS FLATTENEND SPAD TO&OTHER IS TAMPING END)TO CLEAN HOLE. UPON COMPLE TION HE PUT BAR DOWN WITH SPADE END DOWN WITH R IGHT HAND AS HE LET GO BAR SLID THRU BARGRATING FLOOR BEFORE STOPPING THE BAR CAUGHT RIGHT PINKLFINGER AGAINST HANDRAIL CUTTING SKIN

EMPLOYEE WAS SETTING A COMPRESSOR MOTOR, MOTOR BECAME HUNG UP ON DOWEL PIN, EMPLOYEE USED A PAIR OF CHANNEL LOCKS AS A PRY BAR, MOTOR FREED ITSELF WHILE EMPLOYEE PRYED IT AND DROPPED DOWN, CA TCHING HIS LEFT INDEX FINGER BETWEEN BASE AND CHANNEL LOCKS.

EE WAS WORKING TO DISLODGE LUMPS IN WEIGH FEEDER ROTARY VALVE DOGLEG FROM WHICH GYPSUM IS DISCHARGED. UPON OPENING AN 8" INSPECTION PORT, HE OBSERVED SEVERAL LUMPS CHOCKING ROTARY VALVE INLET. EE USED A BAR TO DISLODGE LUMPS WHEN THE SILO FLUSHED CAUSING MATERIAL TO ENGULF EMPLOYEE.

EE WAS USING METAL BAR TO OPEN AND CLOSE RAIL CAR DOORS. BAR SLIPPED STRIKING EE ABOVE LEFT EYEBROW. CUT REQUIRED 3 TO 4 STITCHES. EE RETURNED TO WORK.

EMPLOYEE WAS TAPPING LINERS IN #2 FINISH MILL TO LINE THEM UP WHEN A PIECE BROKE OFF AND PUNCTURED RIGHT CHEEK. STITCHES 2.

EMPLOYEE WAS USING A BAR TO REMOVE CEMENT FROM AN OVERHEAD SCREW CONVEYOR. AS HE STRUCK THE CASING WITH THE END OF THE BAR, HE FELT A BURN- ING SENSATION IN HIS GROIN. THIS INJURY WAS DETERMINED WORK-RELATED ON 5/2/2000.

EE SMASHED HIS THUMB WHILE TRYING TO BUST UP A LUMP IN THE ROCK HOPPER, WITH HIS HAMMER.

EE WAS ATTEMPTING TO CHANGE POSITION OF CLAM SHELL GET, PRYING ON GATE WITH BAR. PINCHED RT INDEX FINGER BETWEEN BAR AND EDGE OF STEEL SKIRTING.

TRIMMING CONVEY9OR BELT CUT TOWARDS BODY. CUT LEFT PALM OF HAND REQUIRED 7 STITCHES, NO IMPAIRMENT.

EMPLOYEE WAS USING AN ADJUSTABLE WRENCH TO TIGHTEN A BOLT. THE WRENCH SLIPPED AND STRUCK HIM, HITTING HIS LOWER LIP.

INJURED EE WAS IN THE PROCESS OF ALIGNING AND SHIMMING ON ELECTRICAL MOTOR THE PRY BAR HIS PARTNER WAS USING SLIPPED, HIS FINGER WAS CAUGHT BETWEEN THE PRY BAR AND THE MOTOR SHIM PACK PINCHING IT AND CAUSING A LACERATION. SUTURES WERE REQUIRED.

EMPLOYEE CLAIMS WHILE PULLING ON CUMOLONG EE HURT HIS SHOULDER.

EE CLAIM RIGHT HAND HURTING FOR ABOUT TWO WEEKS. BELIEVES WHILE USING PICK AND SHOVEL TO HIT ROOTS CLEANING AROUND YARD HURT HAND.

EMPLOYEE WAS POKING A CHUNK OF CEMENT INTO MILL WITH BAR AND THE BAR GOT CAUGHT AND STRUCK THE EMPLOYEE ON THE HAND.

EE WAS USING A SPIKE HAMMER TO INSTALL NEW RAIL IN TRACKS. HAD PREVIOUSLY INJURED SAME ARM/ELBOW. THIS TASK CAUSED NEW INJURY.

EE WAS TIGHTENING BOLTS WITH A WRENCH & FELT A PULL IN HIS BACK [PULLED MUSCLE]. [INCIDENT WAS NOT REPORTED TO SUPERVISOR UNTIL 4/22/98].

EE WAS SWINGING A 10# SLEDGE HAMMER. HE MISSED THE WORK DURING A SWING AND HIS ARM WAS CAUGHT BETWEEN THE HAMMER HANDLE AND A STEEL RAIL WRIST REQUIRED SPLINT

WHILE CHANGING HIS SHOES, EMPLOYEE USED A POCKETKNIFE TO OPEN EYELET ON SHOES. KNIFE BLADE COLLAPSED AND EMPLOYEE WAS CUT ON RIGHT MIDDLE FINGER.

EE DROPPED 30" RATCHET EXTENSION ON RIGHT FOOT [JUST BEYOND STEEL TOE CAP].

EE WAS SQUATTING TO SERVICE A BEARING WHEN HE FELT PAIN.

EE WAS USING A STEEL BAR AND SLEDGE HAMMER TO REMOVE A MATERIAL BUILDUP FROM AN ELEVATOR FEED CHUTE. THE SLEDGE HAMMER SLIPPED, THE EE'S FINGER WAS CAUGHT BETWEEN THE HAMMER HANDLE AND THE BAR . FRACTURE WAS DIAGNOSED ON 9-18-97.

EMPLOYEE USED A BAR TO MOVE A CUTTING TORCH EDGE INTO POSTION, WHILE MOVING SUDDENLY FELT SHARP PAIN IN LOWER BACK.

EE'S FINGER WAS CAUGHT BETWEEN A STEEL BAR, WHICH HE WAS USING TO OPEN RAILCAR DOORS, AND THE GROUND.