Buscar en el registro

EMPLOYEE WAS TRYING TO BEND A BAR BY WEDGING IT BETWEEN 2 STATIONARY OBJECTS. THE BAR BENT SOME AND THEN THE BAR SLIPPED AND HIT HIM IN THE FACE. RIGHT SIDE OF UPPER EYE.

TWO EES WERE REMOVING LINER BOLTS FROM AN FLS BALL MILL WITH A HAMMER AND PUNCH. HAMMER WAS DEFLECTED BY AN ADJACENT HAND RAIL. INJURED WAS STRUCK BY HAMMER ON TIP OF RH MIDDLE FINGER REQUIRIN G APPROXIMATELY 20 STITCHES.

HE WAS TRYING TO SAW A BLOCK OF WOOD TO PROP UP A PRINTER HOOD. THE SAW SLIPPED AND LACERATED HIS THUMB.

EE WAS SWINGING SLEDGE HAMMER, FAILED TO CONNECT WITH TARGET AND OVEREXTENDED LEFT WRIST RESULTING IN A SPRAIN.

WHILE CHANGING OUT BELT CLIP, EMPLOYEE USED A HAMMER AS A BACKING AND HIT CLIP WITH OTHER HAMMER, CAUSING SOMETHING TO FLY AND STRIKE HIS LEFT EYE.

EE WAS REPAIRING PUMP. THE HANDLE ON RUBBER HAMMER HE WAS USING TWISTED. THIS RESULTED IN HIS FINGER BEING PINCHED ON A PIECE OF METAL. RIPPED OFF NAIL OF LEFT MIDDLE FINGER AND CUT TO BONE.

EMPLOYEE WAS USING BAR AND SLEDGE HAMMER TO REMOVE BUILD-UP FROM ISNIDE A PREHEATER VESSEL. HAMMER HIT BAR A GLANCING BLOW RESULTING IN FINGER BEING PINCHED BETWEEN HAMMER HANDLE AND AIR BLAS TER.

EMPLOYEE WAS REMOVING GRINDING BALLS FROM BALL MILL SCREENS USING A PRY BAR AND HAMMER. HE WAS STRUCK IN LEFT EYE BY BALL WHEN HE HIT IT WITH HAMMER. FROM ALL INDICATIONS, HE WAS NOT WEARING PPE (SAFETY GLASSES OR GOGGLES).

EE WAS REMOVING SHIMS FROM A WOODEN CONTAINER CUT HIS FINGER ON LOOSE S41M.

EE WAS ATTEMPTING TO REMOVE A ROCK THAT WAS LODGED BETWEEN THE DUAL WHEELS ON THE MACK WATER TRUCK. HE FIRST USED A PRY BAR TO TRY TO REMOVE THE ROCK AND WAS UNSUCCESSFUL. HE THEN TRIED TO BRE AK THE ROCK WITH A HAMMER. THE TIRE BLEW WHEN HE STRUCK THE ROCK WITH THE HAMMER AND IT THREW THE HAMMER OUT OF HIS HAND AND SENT HIM HURTLING APPROX 8'. BREAKING HIS THUMB, REQUIRING SURGERY

EE WENT TO CLEAN CHUTE THAT STOPPED UP AT 610 PLANT EE WAS USING A BAR (METAL BAR APPROX 6'LONG APPROX 15LBS IN WT ONE END IS FLATTENEND SPAD TO&OTHER IS TAMPING END)TO CLEAN HOLE. UPON COMPLE TION HE PUT BAR DOWN WITH SPADE END DOWN WITH R IGHT HAND AS HE LET GO BAR SLID THRU BARGRATING FLOOR BEFORE STOPPING THE BAR CAUGHT RIGHT PINKLFINGER AGAINST HANDRAIL CUTTING SKIN

EMPLOYEE WAS SETTING A COMPRESSOR MOTOR, MOTOR BECAME HUNG UP ON DOWEL PIN, EMPLOYEE USED A PAIR OF CHANNEL LOCKS AS A PRY BAR, MOTOR FREED ITSELF WHILE EMPLOYEE PRYED IT AND DROPPED DOWN, CA TCHING HIS LEFT INDEX FINGER BETWEEN BASE AND CHANNEL LOCKS.

EE WAS WORKING TO DISLODGE LUMPS IN WEIGH FEEDER ROTARY VALVE DOGLEG FROM WHICH GYPSUM IS DISCHARGED. UPON OPENING AN 8" INSPECTION PORT, HE OBSERVED SEVERAL LUMPS CHOCKING ROTARY VALVE INLET. EE USED A BAR TO DISLODGE LUMPS WHEN THE SILO FLUSHED CAUSING MATERIAL TO ENGULF EMPLOYEE.

EE WAS USING METAL BAR TO OPEN AND CLOSE RAIL CAR DOORS. BAR SLIPPED STRIKING EE ABOVE LEFT EYEBROW. CUT REQUIRED 3 TO 4 STITCHES. EE RETURNED TO WORK.

EMPLOYEE WAS TAPPING LINERS IN #2 FINISH MILL TO LINE THEM UP WHEN A PIECE BROKE OFF AND PUNCTURED RIGHT CHEEK. STITCHES 2.

EE SMASHED HIS THUMB WHILE TRYING TO BUST UP A LUMP IN THE ROCK HOPPER, WITH HIS HAMMER.

REPAIRMAN WAS USING A PRYBAR TO HELP PUT A COVER BACK ON THE ALKALI CHOPPER SCREWS. THE BAR SLIPPED AND THE EE'S PINKY FINGER ON HIS LEFT HAND WAS MASHED BETWEEN A HANDRAIL AND SPUD BAR. DID N OT SEEK MEDICAL ATTENTION UNTIL 12/13/99. FINGER WAS LATER DIAGNOSED AS FRACTURED. I DID NOT RECEIVE NOTIFICATION UNTIL 1/3/00.

EE WAS CROUCHED DOWN TO HOLD A GROUND ROD FOR A CONVEYOR, WHEN EE WAS POSITIONING THE GROUND ROD DRIVER AND IT SLIPPED FROM HIS HANDS DUE TO THE COLD WEATHER, AND THE DRIVER STRUCK EE IN THE M OUTH.

EMPLOYEE CUT RT HAND MIDDLE FINGER, CUTTING BELTWITH UTILITY KNIFE 5 STITCHES.

EE WAS SHOVELING FROM UNDER CONVEYOR AND LOADING ONTO CONVEYOR. SHOVEL CAUGHT BETWEEN CONVEYOR BELT AND RETURN ROLLER BRACKET RESULTING IN LACERATION REQUIRING 11 STITCHES AND FRACTURE TO LEFT THUMB.

WHILE USING A SLEDGE HAMMER TO REMOVE THE LINER FROM A DISMANTLED CRUSHER, THE HEAD CAME LOOSE FROM THE HANDLE CAUSING THE EE TO LOSE HIS BALANCE, HITTING HIS HAND ON THE CRUSHER. THE RESULTIN G CUT REQUIRED 7 STITCHES, BUT NO LOST TIME.

EMPLOYEE WAS TRYING TO MOVE A 1/2" PIECE OF PLASTIC MATERIAL. THE WRENCH SLIPPED AND CUT HIS RIGHT EYE, RESULTING IN 5 STITCHES.

WHILE MAKINE UP A NEW 02 PROBES, EE WAS CUTTING "LIVE" RUBBER WITH A RAZOR (BOX) KNIFE. MATERIAL TEXTURE WAS FIRM AND KNNIFE SLIPPED, CUTTING LEFT THUMB. LACERATION REQUIRED FOUR STITCHES.

EE WAS WATERBLASTING ORIFICE OF PREHEATER WHEN ABIG CHUNK OF MATERIAL FELL & HIT THE GUN CAUSINGTHE PIECE OF EQUIPMENT TO TWIST IN HIS HAND

EMPLOYEE WAS WORKING IN THE MAINTENANCE DEPT ON THE DISCHARGE SCREW AT THE RAW MILL REPLACINGTHE GUDGEON SHAFT. HE WAS USING A PUNCH AND HAMMER TO KNOCK THE BOLTS OUT. WHEN HE ATTEMPTED TO HIT THE PUNCH WITH A HAMMER, HE HIT HIS LEFT HAND INSTEAD.

EE WAS WORKING ON WASH SCREEN PUTTING IN WEDGES WITH 2-3# HAMMER USING LEFT HAND. WHEN HE MISSEDONE HE TRIED TO STOP QUICK WHEN FELT A SNAP BUT NOTHING BAD. HE CONT TO WORK THAT DAY & THE NEXT THEN ON 6/7/99 HE WAS CARRYING A PIECE OF 8" FLAT METAL (1/4" THICK) UPSTAIRS AT THE #3 PLANT WHEN IT SLIPPED. HE TRIED TO GRAB IT QUICKLY WHEN HE FELT A SNAP OR PINCH ON LEFT WRIST

EE WAS SHOOTING A TREE CLINKER BUILD UP IN CLINKER COOLER. THE TREE WAS LOCATED IN THE FRONT OF THE #3 KILN COOLER WHERE CLINKER IS DISCHARGED INTO THE COOLER. WHILE SHOOTING IN #3 COOLER, EE HAD JUST SHOT A SHELL & IMMEDIATELY FELT PAIN IN RT ARM LACERATION WENT TO ER

WORKERS WERE SLIDDING A 22" BEAM 8'8" LONG INSIDE THE WEBB OF OTHER BEAMS WHEN IT BECAME WEDGED AGAINST FLOOR ABOVE, WORKER ON OTHER END OF BEAM HIT IT WITH A HAMMER CAUSING IT TO LOOSEN AND R OTATE ENOUGH TO HIT HIS SAFETY GLASSES IN WHICH HIT CORNER OF RIGHT EYE.

EE WAS CHANGING DRY FLOW PUMP REMOVING BOLTS FROM PIPE FLANGE WHEN LAST BOLT WAS REMOVED PIPE DROPPED & PINNED FINGERS BETWEN FLANGE & ANGLE IRON REQUIRED 7 STITCHES

EE WAS REMOVING JOURNAL BEARING FROM #2 FINISH MILL WHEN BOLT BROKE THAT COMALONG WAS HOOKED TO3/4 TON 1" BOLT HIT IN CHEEK LACERATION CLOSED WITH 5 STITCHES

EE CALLED ASSISTANT PLANT SUPERINTENDANT ON 3/14/99 AND STATED HE BELIEVES HE PULLED A MUSCLE IN HIS BACK ON 3/11/99 WHILE USING A CHAIN PULLER TO PULL THE KILN HOOD BACK.

HE WAS CONNECTING A DUCT BRACE TO DUCT WORK. WHILE LOSENING NUTS ON TUBE THE INSIDE TUBE SLID DOWN HITTING FINGER ON LEFT HAND BETWEEN BASE PLATE ON TUBE AND SUPPORT FRAME.

INJURED WAS USING UTILITY KNIFE TO OPEN CARDBOARD BOX. KNIFE SLIPPED AND STRUCK INJURIED IN LEFT PALM CAUSING LACERATION REQUIRES SUTURE.

WHILE TIGHTENING FITTINGS WITH A WRENCH IN TIGHTQUARTERS, EE STRAINED HIS BACK (LOWER)

WHILE KNOCKING BUILDUP OUT OF CHALK STACKER SHUTE, USING A 12 FOOT BAR, THE BAR SLIPPED OFF THE BUILDUP CAUSING THE EMPLOYEE TO STRAIN HIS RIGHT SHOULDER. WENT TO DR ON 1-19-99. DR SENT HIM FOR PHYSICAL THERAPY AT BRYAN WHITFIELD HOSPITAL.

WHILE TRYING TO DISLODGE A ROCK FROM A CHUTE, EE MIS-JUDGED THE SIZE OF THE ROCK. WHEN IT BROKE LOOSE, IT DROPPED ONTO HIS FINGERS ON HIS LEFT HAND, BRUISING BOTH HIS INDEX AND MIDDLE FINGERS AND CUTTING HIS MIDDLE FINGER REQUIRING 4 STITCHES.

EE WAS USING STEEL BAR TO OPEN BOTTOM UNLOADING GATE FOR RAIL CAR. HE HAD OPENED 6 CARS PRIOR TO THIS ONE AND FELT TIGHTNESS IN HER RIGHT SIDE.

EE WAS PRYING ON DOOR LEVER AT 610 PLANT WITH PRYBAR. PRYBAR SLIPPED & HIT EE ON RT. SIDE OF FACE BELOW EYE. LACERATION, FRACTURE BONE & BROKEN BONE. WILL REQUIRE SURGERY.

EE WAS INSTALLING ELECTRICAL SWITCH GEAR (HARDWARE FOR HOLD ON AIR CONDITION UNIT) WHEN HAMMERING ON A PUNCH, A PIECE OF METAL CHIPPED OFF AND STRUCK HIS LEFT HAND LODGING ITSELF INSIDE THE HA ND BETWEEN THE THUMB AND INDEX FINGER. NO STITCHES WERE GIVEN AND THE FOREIGN BODY WAS LEFT IN THE HAND. MODIFIED DUTY WITH LIMITED USE OF LEFT HAND.

INJURED WAS USING SHOP HAMMER TO DRIVE BEARING OFF ELEVATOR TRACTION SHAFT. A SMALL PIECE OF METAL FLEW OFF THE BEARING AND ENTERED INJURED'S LEFT FOREARM. AN UNSUCCESSFUL ATTEMPT WAS MADE TO REMOVE METAL AND FOUR SUTURES WERE REQUIRED TO CLOSE INCISION.

USING A BOX CUTTER SLIPPED AND CUT LEFT THUMB, REQUIRING 6 STITCHES.

INJURED AND FELLOW EE WERE MOVING SPROCKET TO LOWER PLATFORM BY USING CHAIN FALLS TO LOWER THE SPROCKET WHILE AT THE SAME TIME USING RATCHET FALLS TO PULL THE SPROCKET TOWARD LOWER PLATFORM. T HE SPROCKET WAS LOWERED TO WHERE IT RESTED ON STEPS ALLOWING IT TO TIP OVER AND CHAIN BECAME UNHOOKED CAUSING IT TO SLIDE DOWN STEPS AND STRIKE INJURED'S RT. LEG AND FOOT.

WHILE EMPLOYEE WAS CLEANING THE PREHEATER WITH A 6' BAR A LARGE PIECE OF MATERIAL BROKE LOOSE HITTING THE BAR. THE BAR STRUCK WMPLOYEE' FACE SHIELD AND THE FACE SHIELD BRACKET CUT EE ABOVE THE EYEBROW.

EMPLOYEE WAS POKING THE PREHEATER TOWER WITH TOWER BAR. WHEN THE MATERIAL GAVE WAY THE MOMENTUM OF THE BAR PULLED HIM FORWARD CONTACTING HIS HAND WITH THE OPEN PORT. EMPLOYEE'S RIGHT THUMB WAS SMASHED RESULTING IN LACERATION, BROKEN BONES AND PARTIAL AVULSION OF THUMB NAIL. REQUIRED STITCHES AND SPLINT WAS ADMINISTERED.

INJURED WAS USING UTILITY KNIFE TO CUT RUBBER VACUUM HOSE. KNIFE SLIPPED AND STUCK INTO LEFT WRIST CAUSING LACERATION REQUIRING TWO STITCHES.

EE WAS REPLACING BELT AT NORTH CLINKER CONVEYOR. WHEN HE PLACED THE CABLE CHOCKER ON THE BELT AND BEGAN PULLING AND TIGHTENING IT, HE FELT CHEST PAINS.

HE WAS USING A 5' BAR TO UNCHOKE THE AUXILIARY BELT WHEN HE CUT 3 FINGERS ON LEFT HAND. AREA IS VERY TIGHT TO WORK IN. HE WAS TRYING TO LOOSEN MATERIAL BY USING A STABBING MOTION WITH THE BAR. HE WAS WORKING BETWEEN THE FEED CHUTE AND THE DUST COLLECTOR PICK UP POINT FOR THE AUXILIARY BELT AND HIS FINGERS CAME IN CONTACVT WITH THE FLANGE TO THE DUST COLLECTOR. HE WAS NOT WEARING GL

HE WAS CUTTING FOAM INSULATION FOR THE FEED CHUTE TO THE HAMER PACKAGING MACHINE WHEN HE CUT HIS LEFT INDEX FINGER. HE WAS USING A METAL STRAIGHT EDGE CUTTILNG THE FOAM ON THE GROUND. THE KNIF E WAS NOT LONG ENOUGH TO CUT ALL THE WAY THROUGH TO MAKE THE FINAL CUTS, HE LIFTED THE FOAM WAIST HIGH HOLDING THE FOAM WITH HIS LEFT HAND CUTTING WITH HIS RIGHT. HE WAS CUTTING TOWARDS HIMSE

EE WAS IN THE PROCESS OF INSTALLING REFRACTORY BROCK IN THE KILN. AS HE WAS SHIMMING A BRICK, HE MISSED AND HIT HIS HAND WITH THE HAMMER CAUSING A LACERATION FROM THE SHIM. LACERATION REQUIRED STITCHES.

EE WAS REPALCING WATER PIPING ON CEMENT COOLER. HE WAS REMOVING A PIPE COUPLING WITH A PIPE WRENCH. HE WAS AT FLOOR LEVEL AND REACHING UP AND WHILE TWISTING WRENCH FELT HE TWISTED BACK WRONG A ND INJURED LEFT SIDE.