Esta búsqueda
Envíame un correo cuando un nuevo incidente coincida con estos filtros. Un correo de confirmación; cancela la suscripción cuando quieras.
WHILE OPERATING BLADE, EE DIRECTED HIS ATTENTIONAWAY FROM THE DIRECTION OF TRAVEL. DURING THIS BRIEF PERIOD OF TIME, THE EQUIPMENT STRUCK AN EMBANKMENT, JARRING HIM UNEXPECTEDLY, RESULTING IN A PULLED BACK MUSCLE.
EE WAS PACKING CEMENT WHEN BAG BLEW UP AND CEMENT GOT UNDERNEATH SAFTEY GLASSES INTO LEFT EYE. EE ALSO TURNED BACK WHEN GETTING UP AND HURT BACK. EMPLOYEE'S EYE IS OK BUT IS ON RESTRICTED DUT Y OF NO LIFTING FOR 4 WEEKS.
WHILE ATTEMPTING TO REPOSITION A PNEUMATIC BAG CHAIR EMPLOYEE BUMPED THE BAGGER START BUTTON & MADE THE BAG CHAIR CYCLE DOWN PINCHING & CUTTINGHIS RIGHT THUMB & FOREFINGER.
SEVERAL EES WERE GRINDING OVERHEAD IN A CONFINED SPACE. PARTICLES OF METAL WILL FALL FROM EQUIPMENT DURING THIS PROCESS. AS A RESULT, A PIECE OF THE METAL GOT UNDER THE WELDING HOOD AND BECAME EMBEDDED IN THE LEFT EYE.
WHILE EMPLOYEE WAS ATTEMPTING TO REPLACE A BAD BEARING, THE TRIGGER ON A 3/4" DRIVE AIR IMPACT WRENCH HUNG IN THE RUN POSITION, CAUSING HIS HAND TO BE CAUGHT AGAINST A PIECE OF UNISTRUT.
HE WAS USING A GRINDER TO GRIND ON A PIECE OF PIPE. HE WEDGED THE GRINDER BETWEEN 2 PIECES OF PIPE, WHICH CAUSED THE GRINDING WHEEL TO KICK BACK & STRIKE HIS RIGHT KNEE.
EE WAS WEARING PANTS INSIDE BOOTS THEREFORE ALLOWING HOT METAL TO GET INSIDE BOOT.
EE HAS BEEN BAGGING CEMENT AS HE EXITED PACKER, A SPROUT ON HIS BAGGING SYSTEM INADVERTENTLY ACTIVATED, CAUSING CEMENT TO DEFLECT INTO EE'S EYE. NOTE: HE WAS WEARING A FACE SHIELD AT THE TIME OF THE ACCIDENT
EMPLOYEE WAS GRINDING A PIECE OF STEEL ON A PEDASTAL GRINDER, STEEL GOT CAUGHT BETWEEN GRINDING WHEEL AND GUARD AND SLAMMED DOWN ON THE GRINDER REST, CATCHING EMPLOYEE'S LEFT INDEX FINGER BETW EEN STEEL AND GRINDER REST.
EE WAS ASSISTING WELDER ON WORK WITH PAGE 740 BUCKET. EE WAS SUPPOSED TO TURN HIS HEAD AND NOT LOOK AT THE WELDING ARC IN PROGRESS. EE CLAIMS HE COULD NOT TURN HIS HEAD IN TIME ON SEVERAL OCCA SIONS. LATER THAT NIGHT HIS VISION BLURRED AND HIS EYES BECAME IRRITATED.
EE HAD JUST FINISHED CLEANING OUT MIXER HE RAN IT TO MAKE SURE IT WOULD RUN HE THEN SHUT IT DOWN, LOCKED IT OUT AGAIN AND WENT TO IT TO SEE IF IT NEEDED MORE CLEANING. HE DID NOT WAIT FOR IT T O COAST TO A STOP BEFORE HE PUT HIS HAND IN THE OUTLET CHUTE. A PADDLE JUST BARELY CAUGHT THE TIP OF HIS RIGHT INDEX FINGER.
EMPLOYEE WAS LIGHTING OXYLACETYLENE TORCH. TORCH SLIPPED AFTER BEING LIT. EMPLOYEE'S LEFT GLOVE HAD A HOLE BETWEEN INDEX AND MIDDLE FINGERS. RESULTS WERE BURNS BETWEEN INDEX AND MIDDLE FINGERS
EE WAS WORKING AT CEMENT BAGGING PACKER BAGGING CEMENT. THE BAG BURST ON THE SPOUT, BLOWING CEMENT UPWARD. THIS SURPRISED THE EE. HE RAISED HIS ARM, KNOCKING OFF HIS FACE SHIELD. THE CEMENT DU ST ENTERED HIS EYES. EE WAS WEARING A FULL FACE SHIELD AT THE TIME OF THE ACCIDENT.
EE WAS OBSERVING AN AUGER ON THE SECONDAR CRUSHER THAT HAD RECENTLY BEEN UNPLUGGED. HE RESTED HIS HAND ON THE AUGER HOUSING AND HIS GLOVE-COVERED HAND CONTACTED THE ROTATING AUGER. HIS GLOVE A ND FINGER WERE CUT ON THE SHAPR EDGES OF THE AUGER. HE RECEIVED STITCHES TO HIS THIRD RIGHT FINGER.
HIGHWALL GAVE WAY UNDER A PORTION OF THE MACHINE WHICH CAUSED THE MACHINE TO SLIDE INTO THE PIT AND OVERTURN.
HIGHWALL GAVE WAY UNDER A PORTION OF THE MACHINE WHICH CAUSED IT TO SLIDE INTO THE PIT AND OVERTURN.
EMPLOYEE WAS JACKHAMMERING BUILDUP FROM THE EASTSIDE OF THE UPPER FEED HOOD OF THE PREHEATER. WHEN THE LARGE PIECE OF BUILDUP CAME LOOSE AND FELL IT FORCED THE END OF THE 6 FT JACKHAMMER BIT DOWN WHICH CAUSED THE HANDLE TO FLY UP CATCHING EMPLOYEE UNDER THE RIGHT ARM INJURING THAT SHOULDER. EMPLOYEE MISSED TWO DAYS BEFORE HE ACTUALLYSOUGHT MEDICAL TREATMENT. ON RESTRICTED DUTY.
AFTER USING THE DRILL PRESS, EMPLOYEE MOVED PRESS TO ONE SIDE AND STARTED TO USE THE VISE. WHILE ATTEMPTING TO THREAD HOLE IN THE STEEL PLATE, THE WRENCH GAVE WAY FROM UNDUE PRESSURE, SLIPPING ,WHICH HIS MIDDLE RIGHT FINGER HIT DRILL, CUTTING FINGER.
EE WAS WORKING AT #1 PLANT ON THE #1-41/4' CRUSHER WHILE REMOVING BOWL, EE WAS USING ADJUSTMENT CYLINDER TO TURN THE BOWL. THE CYLINDER HEAD WEDGE MISSED THE NOTCH IN THE BOWL SO EE ASKED F OR CYLINDER TO BE RETRACTED. AT THIS TIME EE GRABBED HOLD OF CYLINDER WITH HIS HANDS AS CYLINDER RETRACTED HIS LEFT INDEX FINGER WAS PINCHED AGAINST CYLINDER
EMPLOYEE WAS ASSISTING CONTRACTOR WHO WAS WELDING AND RECEIVED FLASH BURNS TO HIS EYES.
EE WAS RUNNING A BALL SORTER FOR THE FINISH MILLS, THE DRUM OVERFLOWED AND HE WAS TRYING TO SHUT THE SORTER OFF WHEN A 3" BALL FELL OUT AND HIT THE EE ON TOP OF RIGHT FOOT BREAKING HIS LITTLE TOE.
EE WAS WASHING UNDER LOADER WHEN SOAP/WATER MIST FROM PRESSURE WASHER SPRAYED BACK AT EE AND FLOWED AROUND SAFETY GLASSES, FOAMING IN CONTACT WITH EYES.
EMPLOYEE DISCOVERED AN INPECTION/CLEANOUT DOOR SLIGHTLY OPEN ON THE RETURN PIPE OF THE BYPASS. HE ASSUMED THE AIR BLASTER HAD BEEN TURNED OFF AND ATTEMPTED TO CLOSE AND SECURE THE DOOR. AS HE CLOSED THE DOOR, THE BLASTER TURNED ON, BLOWING HOT GAS AND MATERIAL ON THE ARM AND CHEST, AND LEFT SIDE OF FACE. HE WAS NOT WEARING PROTECTIVE EQUIPMENT AT THE TIME.
HE SAID HE TOLD OUTSIDE MAN TO CUTOFF BOTTLES OUTSIDE. HE FIGURED THAT BOTTLES WERE OFF SO HE STARTED UNDOING HOSES FROM TORCH BARRELL. AT TIME HE REALIZED BOTTLES WERE NOT OFF SPARKS FROM WOR KER ABOVE DROPPED TO HIS LEVEL AND IGNITED ACTYLENE AND OXYGEN IN WHICH BURNT INSIDE KNEES AND AROUND THIGHT.
INJURED AND THREE OTHERS WERE MOVING A STAIR STRINGER THAT WAS LYING ACROSS THE TOP OF SEVERAL I BEAMS THAT WERE STANDING UP WHILE MOVING STAIR STRINGER ONE OF THE BEAMS FELL OVER CATCHING HIS RIGHT FOOT UNDER EDGE OF BEAM CRANE HUNG HOOKEDTO STRINGER, THEY UNHOOKED AND HOOKED UP TO BEAM THAT WAS ON HIS FOOT SO IT COULD BE REMOVED.NO BROKEN BONES BUT LCERATION TO BOTTOM OF FOOT.
EES WERE WORKING INSIDE BAGHOUSE AT AN ELEVATION OF 70'. AN AERIAL LIFT WAS BEING USED TO GAIN ACCESS TO THE BAGHOUSE DOORS. PROCEDURE CALLED FOR LIFT BASKET TO BE POSITIONED AT THE OPENING TO ALLOW FOR SAFE ACCESS FROM THE BASKET GATE. BEFORE BASKET WAS FULLY INTO POSITION, EE DISCONNECTED HIS HARNER LANYARD, REACHED OUTSIDE OF THE BASKET AND GRABBED THE OVERHEAD DUCT FLANGE. HE T
EMPLOYEE WAS WORKING AT RECLAIM HOPPER AT QUARRY CHANGING SKIRT RUBBER ON RECLAIM BELT. WHILE USING AN ELECTRIC IMPACTOR WRENCH, SOMETHING FLEW UP AND HIT HIM ON THE CHEEK AND ENTERED HIS RIG HT EYE.
EE HAD BEEN WEARING A FACE SHIELD 5 MINS PRIOR TO ACCIDENT WHILE USING WATER BLASTER. WAS USINGA SPUD BAR WHEN THE PREHEATER WENT POSITIVE. EE WAS WEARING SAFETY GLASSES HOT DUST CAME OUT OF INSPECTION PORT & BLEW INTO INJ'S EYE & FACE
EE WAS CHIPPING BUILD-UP FROM GSC 59. WHEN HE FINISHED HE RAISED HIS PROTECTIVE FACE SHIELD AND PARTICLES OF MATERIALS FELL FROM SHIELD AND/OR HARD HAT INTO EYES.
EE WAS WORKING AT THE 8' BENCH GRINDER. HE WAS USING THE BUFFING WHEEL OF THE GRINDER TO BUFF RUST OFF OF AN OLD PAIR OF PLIERS. HE PLACED THE PLIERS AGAINST THE BUFFING WHEEL WITH HIS RIGHT H AND. HIS LEFT HAND WAS NEAR THE REST. AS HE BEGAN TO BUFF THE PLIERS, THE BUFFING WHEEL GRABBED THE PLIERS WHICH IN TURN CAUGH HIS FINGER OF LEFT HAND BETWEEN THE TOOL REST AND PLIERS.
EE'S SAFETY GLASSES HAD FOGGED. HE REMOVED GLASSES TO CLEAR THEM. WITH GLASSES OFF, HE LOOKED UP AS HE FELT XXXX HARD HAT SLIPPING AND A PIECE OF STONE FELL FROM GRATING UNDER WHICH EE WAS STA NDING AND HIT HIM IN THE LEFT EYE CAUSING INJURY.
EMPLOYEE WAS JACKHAMMERING A CHUNCK OUT OF SILO ABOVE DISCHARGE GATES WHEN THE SILO FLUSHED, STRIKING HIM IN THE FACE AND KNOCKING HIS GOGGLES AND GLASSES OFF.
THE EE WAS CUTTING BOLTS FROM 316 DIFFUSER WITH A TORCH, WHICH IS A TIGHT AREA, HE REPOSITIONED HIMSELF & LOST HIS FOOTING & BURNT HIS LEFT ARM WITH THE TORCH.
EE IS A SUMMER TEM LABORER AND HAS BEEN JACKHAMMERING ON THE PRHEATER TOWER. ON 7/31 WHEN TAKINGA BREAK HE REALIZED THAT HE HAD LOST HIS RANGE OF MOTION WITH LEFT ARM AND FELT SHARP IN IN THE ELBOW AREA.
EE WAS JACKHAMMERING WITH A 14 LB JACKHAMMER. HE WAS SCALING THE COOLER FLOOR AND THE BIT JUMPED UP AND SLID FORWARD, CATCHING MORE MATERIAL. WHEN IT CAUGHT, EE TWISTED HIS WRIST (RIGHT). THE EE HAD HIS BODY WEIGHT ON JACKHAMMER, WHICH IS NOT STANDARD PRACTICE.
EMPLOYEE REMOVED INSPECTION COVER ABOVE THE ROTARY LOCK FOR F133 DUST COLLECTOR & REACHED INSIDE TO REMOVE A CHUNK. EMPLOYEE IS NOT SURE IF HE PULLED THE SWITCH AND LOCKED EQUIPMENT OUT. SYS TEM IS INTERLOCKED AND WAS FOUND RUNNING AFTER ACCIDENT REPORTED.
EE IS AN EE OF PROTEMP STAFFING SERVICES. EE ALLEGEDLY AGGRAVATED A PRIOR BACK INJURY WHILE WORKING ON SOUTHDOWN KNOXVILLE CEMENT PLANT PROPERTYEE STATED HIS INITIAL INJURY OCCURRED IN 1987 WH EN HE WAS INVOLVED IN A MOTORCYCLE/TRUCK ACCIDENT. HE THEN STATES BACK INJURY WAS ALLEGEDLY AGGRAVATED ON 10-3-96 AND ALSO APPROX. ONE MONTH AGOWHEN HE OPERATED A JACKHAMMER & RIDING LAWN MOW
EMP WAS WASHING #2 KILN FEED SHELF WHEN ONE OF THE AIR BLASTERS DISCHARGED CAUSING HOT GASES ANDMATERIAL TO BLOW OUT OF THE 10" WEST PORT ONTO HIS RIGHT FOREARM AND FOREHEAD.
EE WAS PACKING MASONRY CEMENT AND ONE OF THE BAGS HE WAS LOADING BURST. WHEN THE BAG BURST, CEMENT WAS BLOWN INTO THE RIGHT SIDE OF HIS FACE. ALTHOUGH THE EE WAS WEARING SAFETY GOGGLES, THE CE MENT PARTICLES ENTERED THE GOGGLES THROUGH THE AIR VENTS AND CAUSED A CHEMICAL BURN TO HIS EYE.
EE WAS LIGHTING A GAS TORCH AND A PORTION OF THE COTTON MATERIAL USED TO GINITE THE FLAME CAME BACK INTO HIS HAND.
EMPLOYEE BENT OVER TO REMOVE STUCK BAG UNDER PACKING MACHINE. PACKING MACHINE WAS NOT SHUT DOWN.ANOTHER BAG FILLED AND RELEASED. DUST CONTINUED TO FLOW OUT OF THE SPOUT AND INTO THE EMP'S FACE . HE WAS WEARING EYE GLASSES.
EMPLOYEE WAS WORKING ON REPLACING JEFFREY HAMMERS. GRINDING ON HAMMER WHEN A PIECE OF MEETAL HIT CHEEK AND INTO EYE LID.
EE HAD FLAME CUT BEARING FROM SHAFT. REMOVED GLOVES AND KNOCKED SHAFT THRU DRUM ROLLER. FAILED TO PUT GLOVES BACK ON AND GRABBED SHAFT TO PULL IT OUT OF ROLLER.
EE WAS WELDING ON #3124 DISCHARGE CHUTE, HOT SLAG FELL ON HIS CROTCH AREA. BURNT THROUGH HIS PANTS ONTO HIS GENITAL AREA. 2ND DEGREE BURNS.
THE OPERATOR TURNED THE KILN ABOUT 3/4 OF A TURN. HE STOPPED THE DONKEY AND REQUESTED BY RADIO THAT WEDGES BE INSERTED IN THE TRUNNON ROLLS AS STOPS. DUE TO THE HEAVY LOAD BEING OFF CENTER, TH E KILN ROLLED BACK CRUSHING THE WOODEN STOPS AND OVER REVVING THE CLUTCH ASSEMBLY ON THE DONKEY DRIVE. WHEN THIS OCCURRED, THE CLUTCH ASSEMBLY TORE APART DUE TO CENTRIFUGALFORCE AND SHATTERED
INJURED WAS USING A PROPANE ROSEBUD TORCH TO THAW OUT FROZEN GYPSUM IN NORTH GYPSUM TANK. THE MATERIAL BROKE LOOSE AND CAUSED A BLOW BACK INTO THE EE FACE. INJURED SUFFERED FIRST AND SECOND DE GREE BURNS TO FACE, MOSTLY AT LOWER NOSE AND UP.
INJURED WAS OPERATING PAVEMENT BREAKER (JACK HAMMER) TO REMOVE MATERIAL BUILD UP & DROPPED TOOL ON RIGHT FOOT INJURED SUFFERED BRUISE TO TOP OF FOOT
EE WAS ON SWEEPER, HE WAS GOING AROUND CORNER ON NORTH SIDE OF ADMINISTRATION BUILDING AND MATERIAL FLEW INTO HIS RIGHT EYE.
EMPLOYEE WAS REMOVING BUILD UP IN DROP OUT DUCTS ON PREHEATER TOWER USING A JACKHAMMER THESYSTEM TURNED POSITIVE & BLEW HOT SULFUR GAS & DUST OUT& SOME BLEW INTO EMPLOYEES RIGHT EYE EMPLOYEE CONTINUED TO WORK HIS REGULAR DUTIES THROUGH 07-09-95 HE WAS RESTRICTED FOR WORK ON 07-10-& 07-11 DUE TO INFECTION IN EYE
EE WAS AT EXTERIOR AREA OR PROPERTIONARY AREA AT SOUTH FEED BELTLINE REMOVING BUILDUP OF CLINKER. AT TIME OF INCIDENT, EE WAS JACKHAMMERING WHEN MATERIAL FELL STRIKING EE IN HEAD. EE LOOKED UP AND PIECE OF MATERIAL STRUCK EE IN LEFT FRONT CHIN CAUSING LACERATION. EE RECEIVED 5 SUTURES.