Mine operator twisted ankle while exiting a transport van. Medical examination assigned work restrictions. Operator returned to work next shift but declined to perform restricted duties. Operator reports ongoing physical therapy for injury and has not returned to site in any capacity.
Employee was stepping over a pipe when EE struck EE's right knee on the flange connection and cut through EE's pants, cutting EE's knee.
Two employees were working together to clean up some using a forklift to maneuver drill steels. The employee on the ground had their hand on top of a drill steel when another shifted and moved towards the other steel catching their finger between the two drill steels and crushing it.
Operator was walking on uneven ground and felt pain in their knee. After evaluation employee was placed out of work by the medical provider beginning on 12/10/2025.
Mechanic was moving a loader cutting edge from a pallet onto the forks of a forklift and when dropping it onto the fork EE's finger was caught smashing EE's right index finger and causing a laceration which required sutures.
A Mobile Maintenance Mechanic was removing cutting edges off of a forklift, as they set it down to flip it over their finger got caught between the cutting edge and corner of forklift smashing their finger, employee received sutures to close wound.
A Haul Truck Operator was climbing from truck to the ground using the handrails and 3-step boarding ladder when they fell from the second step to the ground. They were transported to the hospital for evaluation and was placed out of work for a suspected concussion. Their first shift of lost time was 10/19/2025.
The victim was preparing the area to lower a vulcanizing hot press down to the lower level by removing grates on the 2nd floor of the number 2 ball mill feeder belt. In the process, the victim, who was not wearing fall protection, fell 10 feet to the lower level.
Employee was cutting flex using a utility knife. Employees knee slipped causing them to make contact with upper right knee, causing about a 1inch laceration.
A maintenance mechanic was inside the discharge chute of Ball Mill #5 and was using a 12-pound sledgehammer to break a chute liner loose when EE's footing slipped mid swing and the hammer hit EE's right knee causing a chip fracture.
A Lube Technician was dismounting a dozer in the pit after servicing it, when stepping down they felt pain in their ankle and felt a pop. EE was sent to a provider for evaluation on 09/11/2025 and was diagnosed with a sprain injury and placed on crutches, first day of lost time was 09/12/2025.
A mechanic was stepping onto a barge from the ground when their muddy rubber boots caused them to lose footing and slip and caught themselves by grabbing the handrail and hurting their right shoulder.
A production loader operator was coming off the boarding ladder of the loader when EE stepped on a rock and felt pain in EE's leg. On evaluation EE was diagnosed with a muscle strain and issued restricted duty, EE's first shift of restricted duty was 09/05/2025.
A haul truck operator noticed redness and swelling on EE's forearm assumed to be from an insect bite or sting, on evaluation EE was referred to medical evaluation for a possible allergic reaction. EE was was diagnosed with an acute, localized reaction and prescribed a steroid and light duty for the course of medication.
THE DRIVER WAS HAVING TROUBLE REMOVING THE HOSE AND THEY PULLED ON THE HOSE, THAT WAS WHEN THE HOSE WENT STRAIGHT TO THEIR BOTTOM LIP, IT CUT BOTTOM LIP, PUSHING THE BOTTOM TOOTH INSIDE, CAUSING BLEEDING AND PAIN.
While waiting for the shift to begin the employee sat in a chair next to a cork board mounted on a wall. The cork board fell and struck the employee on the left shoulder.
Employee was replacing a drive sprocket on a excavator. While attempting to install the sprocket fell off of the forklift and landed on ankle. Took employee to the emergency room and had x rays taken. Results were no broken bones or torn ligaments. Ankle is fine just some swelling and bruising.
While waiting for shift to start employee was rubbing eyes when they felt a sharp pain in their eye after touching welding jacket. Employee was seen at the ER where a foreign object was removed from their eye.
As The operator was dismounting the haul truck, right hand stuck to the handrail as their foot reached the ground. At that time they felt a sharp pain from the front of right shoulder. Issued 2 lb lift restriction, no driving, no operating equipment, no climbing ladders. Began restricted duty on 06/13/2025.
Operator of dozer was starting a new slot and as the material fall away ahead of the blade, the dozer operator quickly reversed and tracked over the previous slot embankment edge. The dozer laid over onto its left side, operator was wearing their seatbelt and was able to self-extricate. Operator was then sent for evaluation at an off-site clinic where they were issued restrictions.
Employee was using a 6"" grinder with a cut off wheel cutting flat plate on a set of stands when the grinder grabbed and kicked back toward the individual making contact with EE's left mid to upper thigh resulting in a laceration and 11 stitches.
Employee was walking from the Main Gate to the Administration building and there was a pickup next to the gate, they walked around the pickup and turned to talk to the driver. As they turned back to continue walking, they stepped into a dip in the pavement, twisted an ankle, and fell resulting in an ankle fracture.
Operator went to fuel island and the pump 2 hose had been rolled back up. In the process of pulling hose back to the east side of fuel island, operator went to get more hose out of reel and in doing so strained their back as they were turning their body. First missed shift was 04/25/2025.
Operator of drill 557 was leaving tie down attempting to go down ramp to Castle dome pit, during that walk Haul truck 531 was attempting to pass drill, When haul truck attempted to pass it struck rear of drill mast causing damage to both and injuring the drill operator. First missed shift was 05/30/2025.
Employee was attempting to retrieve tools from the back of employee's pickup and cut right hand on an exposed, sharp, piece of metal located at the top of the tailgate. Employee received a cut to the top of right hand above the thumb which required 5 sutures.
While removing the wear caps on a loader bucket, they struck the cap with a hammer which caused a metal fragment to fly off and embed in this left hand between the thumb and index fingers through a leather glove and the embedded metal had to be surgically removed. First missed shift occurred on 04/02/2025.
Employee was operating a haul truck and was being loaded by the production loader and felt some discomfort in their back, the employee was reassigned to a different loading unit and finished the shift but after leaving the following morning, called their Supervisor and reported that they needed to visit the ER. The restrictions would not allow return to work for the next shift.
Employee was backing a dozer on the main dump and contacted a rock with the back of the dozer, this caused a sudden stop which jarred EE and caused neck pain. First day of work missed 02/19/2025.
As the employee was dismounting the haul truck, EE stepped off the last rung of the ladder and stepped on an unseen small rock and rolled EE's knee inward. First day of missed work was 02/06/2025, following revised restrictions from a follow-up visit.
Employee was priming holes, as employee moved to push wire down the lath / stake a splinter came from the wood and entered employee's hand between the thumb and pointer finger, it then pushed back into the back of the hand.
Employee was cutting a bolt off with a DeWalt portable bandsaw. When the saw cut through the bolt, it dropped down coming into contact with the left thumb causing a laceration.
While installing Feed pipe to the #2 skid at TSF4 an excavator was being used to position the pipe in place. With the stored energy left in the pipe it swung back approximately 10 feet striking the employee in the lower right leg.
Employee was helping to adjust the gap on Crusher #5 using a hydraulic ram. When the ram began to retract, it slipped off of the crusher tooth and the employee grabbed it, crushing their Right ring and pinky finger between the ram body and head.
Maintenance employee was working to install a bearing on a conveyor pulley and cut the second knuckle on EE's right hand middle finger.
Maintenance employee was placing a training idler onto a conveyor cartridge that was being rebuilt. While placing the idler into the frame, it shifted catching employee's pinky finger on left hand between the idler and frame.
Employee was removing an inline valve on the tailing pump discharge line and when the last bolt was removed, the valve shifted releasing pressurized tailings slurry which got in employee's face/eyes.
EE was tightening bolts on a rebuilt pump when EE felt a pain in EE's back.
Employee was removing brush and weeds while standing on a pallet and slipped causing EE to fall to EE's knee. New restrictions issued on 10/14/2024, first missed shift is 10/16/2024.
Employee was loosening a bolt with an impact gun and had hand on the socket while activating the impact when a sliver of steel caught EE's finger causing a laceration.
Employee was boarding employee's haul truck and for an unknown reason, chose to utilize the emergency egress ladder rather than the normal boarding ladder/stairs. EE reached the third rung from the top when EE fell approximately 11 feet to the ground. EE received a head laceration, fractured right thumb, fractured collarbone, and fractured C6 lamina.
Employee was climbing Scaffolding felt a pop and sharp pain in the left knee. Employee was diagnosed at medical facility with strain/sprain to the knee. Was referred to physician for further evaluation.
Employee reported back strain after climbing the boarding ladder/stairs of employee's haul truck. Pain reported the following day on 07/05/2024. Employee issued restrictions of no driving, stairs, or uneven ground by medical provider.
Tire technician was removing a lock ring from a haul truck tire when the lock ring pinched EE's fingertip. *EE was diagnosed with a secondary infection due to improper wound care during a follow-up visit on 8/5/24 resulting in restricted duty work beginning 08/05/2024. Restrictions listed as wear splint, keep hand clean/dry, no lifting/push/pull over 10 pounds.
Employee was walking down a conveyor walkway and slipped on debris.
While operator was going to move plastic pallet from table to set up for next day starter sheets as operator was moving the pallet it slid of table causing employee to lose balance falling back and hitting lower left triceps, causing a laceration requiring sutures, and a bruise and swelling on elbow area.
Employee was harvesting cathodes in the tank house and had a dropped sheet inside of the cell. While trying to fish the sheet out with a handled hook, EE pulled to lift the sheet and it snagged on the side and dropped off the hook and felt a pull in EE's back and radiating down left leg. Employee was given restrictions of 5 lb lifting, no stairs, no squatting.
Employee was operating a road grader and noticed the transmission was not working correctly. Operator was inspecting for leaks, when they opened the engine compartment door the transmission fluid cap popped off causing them to be splashed with oil which got in their eyes.
Employee was performing semi annual service an HT518, was headed to back of the motor to cut zip ties on the detection line after stepped on tubing, foot slipped and worker's leg caught a bracket which cut calf on right leg.
Twisted right knee while exiting the truck.
Moving material to clear belt, smashed fingers on right hand.
Plate slipped off the rope falling onto employee's hand causing a laceration
EE was pouring some chemicals into a tube and a small amount got onto EE's arm creating a small burn.
Driver was placing lid on copper concentrate container and needed to slide it over. While using bar, lid shifted causing wrist to twist. Tweaked right wrist and felt a pop.
Installation of new silo components (feeder tube), when a bolt broke and the tube fell approximately 5 ft onto employees right foot (above steel toe). 2 fractures diagnosed, employee given a walking boot, crutches, restrictions of no weight bearing on right leg.
Employee was standing on loose gravel near the facility, installing signage. Employee lost footing while using prybar, causing employee to fall to the gravel and striking left knee. Employee was evaluated by a care professional and required sutures and follow-up visit. No other care required. No lost time required. Returned to full duty on next scheduled workday.
The condition contributing was a highwall failure. Employee was extracted out of right window of the piece of equipment. Employee had used their right arm and shoulder trying to break the window causing an injury.
Person was bracing against pipe with right knee, when a bobcat hit the pipe into EE's knee.
Injured Right knee and did not report until 7/7/2023 and then EE was out on EE's 7 days off and will become a lost time on 7-14-23.
Employee was using a metal shear and when activated the plate popped up catching employee's left thumb between the plate and the body of the machine.
Tripped and fell on grating injuring EE's finger
Employee was using the striker lighting a torch when it ignited it burned through a hole in employee's glove causing a burn to the index finger.
struck hand with a hammer while setting clamp in groove
Rolled ankle on rock hidden in mud on Drill steps Date of incident was 1/2/2023 date EE became a lost time is 02/23/23
helping with a cyclone feed pump and smashed EE's right ring finger while removing belts from the motor side
Installing 16"" casing and employee's finger was caught between mainline and bolt on elevator dog ear latch.
Operator was walking from the piece of equipment to the restroom when EE tripped over EE's feet causing EE to fall to the ground. Employee is being treated for a shoulder fracture. Employee was initially injured on June 24th however the fracture was not found until the follow up appt. on July 21st making it reportable. Employee has not lost any days.
Person was injured June 9th and worked until results showed a fracture. Is now out as of 7-7-22. Fracture was not found until 7-7-22 and has become a lost time. Employee had been released for work as part of normal job duties prior to the diagnosis.
Employee tripped while making rounds fell and cut left hand.
While inspecting crush cavity on #1 crusher employee pushed open the rubber skirt to look in and was struck with a rock on the finger.
Jostled while being loaded causing lower back pain
Involved in a single light vehicle accident on the haul road, vehicle came to a sudden stop. Person was sitting in the back seat of the vehicle
2 Employees were cutting 1"" thick steel plate that was placed on stand making sure to pay extra attention to orientation of plate so that it did not fall after being cut. While placing a piece of angle iron on the plate the stand tipped over and the steel plate landed on EE's foot causing a laceration. The injury required 4 stitches.
Driver stared shift at 10:30 pm on 04/07/2021. While placing a seal on a container the driver was stepping from catwalk onto the container and rolled EE's ankle. EE required assistance at this point.
Employee states cleaning muck off the table and adjusting easier skirt with a hammer while belt was running. Hammer slipped and went into roller and took EE's hand in. Damages broken bones in right hand and swelling of the arm which lead to skin graphing.
Fell into open hole in grating that required stitches.
Changing bolts on G.E.T replacement. Cutting edge fell on right knee
EE was using a Hytorc wrench to tighten mill shell bolts. EE's left ring finger tip was caught between the mill shell and the wrench.
Employee was using a metal bar to move plates to set a truck frame on stands. The bar came out of the employees hands and landed on the top of employees foot.
EE was walking in some mud while carrying weight and EE's ankle gave out/twisted.
The employee injured their wrist when they fell from the truck during dismount.
Cut finger while connecting to a trailer.
EE was affected by a spill from a valve that was bumped and opened on a level up above.
Employee was assisting moving a lifter toward the center of the mill to fit in the required location. Another employee was hitting the lifter with a sledgehammer to push a bolt out of the bolt holes and the first employee's thumb got in the way causing it to be hit with the sledgehammer.
Stumbled and fell on hands required stitches.
An employee was pulling the last set of cathodes in a cell at the SXEW and tried to grab a copper bar while holding the strongback. The employee felt a shock go through their body to their hand. Seen by site First Responders and flown to a hospital in Phoenix for further evaluation.
On 12/11/2018 we received notice from our workers compensation insurance company that this employee has been diagnosed with biopsy proven anthrasilicosis secondary to dust inhalation. The date of illness is 2-11-2014.
An employee was travelling in the outlying area, got out to check something on their light vehicle, then tripped and fell approximately seven feet down a hill side. They struck a cactus and received abrasions on their torso and a laceration on their hand that required stitches.
IE claims ee was struck in the face (left cheek) while attempting to open #2 standard crusher feed box in the fine crushing plant. Alleged incident occurred on 10/17/2018, the employees dentist appointment on 10/22/18 put ee off work 10/23/2018. The mine is controverting this as work related injury.
Steel bracket was on top of the bucket, when the bucket was tilted it fell off and struck the technician on the shoulder, and arm.
employee had pain in back while reaching for a hose, tripped and fell striking EE's chin on a rock.
an employee was walking across mill parking area, lost EE's footing on the uneven surface causing an ankle sprain.
employee felt a sharp pain in abdomen area while lifting a drill bit. Umbilical hernia with out obstruction or gangrene
While replacing an oil filter in the fine crusher plant, employee struck hand on a pipe causing fracture to right little finger.
While closing the valve at the mine water stand it started to free spin. Employee grabbed it and the handle struck right hand causing bruising.
While washing down slurry from the lip of the number 6 ball mill cyclone underflow box, employee was splashed with slurry mixture in the left eye.
While stacking filter plates on a pallet, employee caught middle finger on right hand in-between 2 filter plates resulting in 10 stitches.
EE pulled the Tractor Trailer w/container up to seal placement rack. When on top of the rack there is a ""trap-door' in the catwalk. EE said EE placed the security hook to trap door to prevent it from falling. As EE was placing the seal lock on the manhole cover, the trap door fell down. the trap door hit EE in the back of EE's head pushing EE's forehead into the catwalk.
While installing and checking alignment on a dust collector belt, employee received a laceration on right index finger requiring stitches.
While cutting angle iron with a 4"" grinder, employee lacerated right index finger and required eight stitches.
Employee was kneeling down, when employee stood up felt a pull/sharp pain on left knee.
While rotating tires on a haul truck, employee's left hand was pinched in the tire lock ring and received a laceration between the thumb and first finger requiring 8 stitches.
Employees were installing cyclone feed pump into lower floor of mill area, employee was guiding a bolt into the base of pump, bolt hung up smashing right hand middle finger resulting in partial amputation between 1st and 2nd knuckle.
Employee was welding a bracket on a drill in the pit and felt pain in right shoulder.
Employee was sprayed in the face with flotation reagent after hose from pump discharge fell off. Antibiotics prescribed by eye doctor.
Haul Truck down shifted after hitting bump while driver was reaching for their lunch box causing employee to feel stinger in lower back.
While re-stacking hydraulic cylinders from wooden pallet to plastic pallet, employee pinched finger between two cylinders when they shifted.
Mechanic was going to fuel drill at the bottom of east ramp when EE lost the brakes and rode truck down to bottom of pit where the truck flipped onto its left side.
Employee was putting rigging into mantle while lining up eye bolt, crane hook drifted down and smashed left thumb, nail was removed and 3 stitches applied.
While using a pipe wrench to move a bolt on a conveyor belt, the wrench slipped and employee's hand struck the floor causing pain in left wrist.
Employee was packing down shim box and aligning tools on incline and felt right knee twist.
Employee hit hand on beam while holding end of pipe causing laceration to right index finger requiring sutures.
Loader operator activated fire suppression system after flames were noticed and suppressant got in operator's eyes.
While carrying a pressure washer, employee slipped and fell on knees and hands. Diagnosed with fracture of thumb on 5/3/17.
While turning the master key switch on haul truck, employee hurt right wrist. Brace was issued by doctor.
Steel liners fell from a set of springs and landed on employee's left foot.
Employee picked up handles of wheel barrow when sharp pain shot down right wrist to fingers.
Employee was walking down stairs and left knee gave out and ee fell down three steps to stair landing.
Employee states slipped on mud and felt a tweak in left knee.
While adding Hydraulic and Transmission Oil to LD#998, the employee saw that the lube truck was leaking oil, and in the process of running over to push the E-Stop Button, employee strained right calf muscle.
Employee was struck by a dropped object from upper level.
Truck operator reported that EE was having back pain and difficulty breathing after hitting a rough spot in the road.
Hard hat fell off, employee stood up striking head on the cross tube section of the haul truck.
Employee was checking the Moly Vacuum Pump directly outside of the Moly Boiler Room when ee discovered flames coming from the Thermal Fluid Expansion Tank and material dripping onto the tank.
Operator was climbing on water truck and became dizzy and light headed, then fell off step to the ground injuring left shoulder, head and right knee.
Wind blew door of truck shut, pinching the employee's fingers.
While removing pin from adapter on shovel, employee struck left knee with 4 lb hammer causing bruise.
While changing bolts on slurry pump, the bar being used slipped, causing the employee to fall backward and trip over a conduit on the ground landing on left wrist.
Employee walked around loader, tripped over rock and fell to ground landing on elbow and hip.
Employee struck lip protector on shovel and a piece of metal broke off and struck EE in the leg.
While using overhead crane to lift a bearing over a handrail, the employee's hand was pinched between load and handrail.
Employee strained right thumb and forearm while unloading three 2"" diaphragm pumps from the rear of a flatbed truck.
Employee was using a 6' air lance to un-choke launder line and felt a strain in the upper back between the shoulder blades.
Removing bolts from a valve when finger got caught between wrench and pipe flange taking off tip of finger.
While scouting a path for equipment operators to access a downed power line, employee slipped and fell, twisting left knee.
Shovel operator made contact with bed of haul truck, jolting the haul truck driver.
While preparing mine drill samples and after lifting a Pot out of a pulverizer, EE turned around to perform another task and felt a sharp pain in back.
While installing guard on #3 ball mill cyclone feed pump, employee pushed guard and pinched left hand resulting in fracture to left middle finger.
Filling up hydraulic tank on crusher units hose came off and hose clamp was put on hose and it came off and sprayed employee and got in eyes.
While removing a cover to enter #22CV04 the cover was pulled toward Employee and the Rear fell to Belt and pinched Right Thumb between the Cover and a Angle Iron support.
An employee was starting to cut out a bearing on a pump barrel when the grease flashed in the bearing and a fire ball of grease shot out of the bearing and deflected off the face shield of the employee cutting the bearing and struck another employee standing nearby in the facial area with hot grease.
Employee was torqueing bolts on a 789 front suspension. During the torqueing process the tooling slipped, this caused the reaction arm of the gun to come around and contact one of his fingers. He sustained a cut of the fingertip and fractured the tip of the bone.
Employee attempted to stand from the sitting position and felt sharp pain in his lower back.
After washing down haul truck employee slipped on wet surface causing groin strain.
Employee was hit in the ankle when steel rail was bumped by forklift and slipped off wear metal.
Employee attempting to unstick ladder from haul truck to dismount fell back on his wrist
Employee strained left shoulder when nut came loose and impact fell back off socket. The doc checked him out and gave him a full duty release. It was still hurting him so we took him to a shoulder specialist on 10/2/15 who gave him light duty
Employee felt strain in chest muscle when attempting to turn pump sheave
Employee using excavator to clean highwall and boulder hit cab shattering right window getting glass in R eye
Employee jammed his right pinky finger when pushing broom.
Employee tasked with troubleshooting 480v belt drive motor due to poor connection at termination. As he attempted to remove splice covering to visually inspect, the knife slipped and contacted left thumb knuckle resulting in a minor laceration. Medical treatment administered, sutures were applied to close the wound.
Employee walked into a low hanging light fixture hitting his head and causing neck strain
Employee was not used to working under smaller haul trucks and stood up and hit his head causing back pain
Employee slipped on water while walking to the Lime Plant and he fell backwards hitting his head on the cement slab.
Another contractor's truck was backing up and his rear bumper struck our worker's right leg/hip. Worker was taken to local hospital for x-rays/tests. All x-rays/tests came back clear. No broken bones or injuries sustained, only bruising. Worker was released to full work duty on June 29, 2015.
Employee was instructed to install a new high voltage feed to power a pump. The cable was heavy and he sprained his shoulder when positioning the cable.
Closing 2C cyclone and stepped up on the beam to reach airline. When stepping down, did not place foot all the way on the ground, and slipped on the beam causing her to twist her right ankle. Requested no further medical attention at this time.
Employee walked through regrind water with Lime in it and burned her foot and leg
Employee smashed left thumb between ripper pin and pin hole.
Employee was mixing chemicals in 30ml vile when she dropped it and the mixture containing small % HCl and small % H2SO4 splashed in her eyes.
Employee was swinging a steel bar trying to break a nut loose and strained shoulder. ***On the 28th the doctor returned him to full duty with no restrictions and scheduled an MRI. After the MRI the doctor reviewed him again and on 5/21/2015 put employee on work restrictions thus this report.
While moving 4"" X 20' piece of Drisco pipe, employee stumbled over small windrow of tailings and fell to his knees causing muscle strain on lower back.
Employee strained left foot ligaments when he stepped on the feed cart rail.
Employee took shortcut through muddy puddle while carrying 3 empty 1 gallon tanks and slipped causing a strain on his left knee
EE's were installing a tramp cylinder on cone crusher. Cylinder was placed on the spring tower. One EE was raising cylinder support plate other EE was holding the tramp cylinder. Cylinder slipped off the tower catching the EE's hand between the tramp cylinder and the main frame leg support bolt.
Employee pinched right thumb between wrench and screw causing laceration.
EE was attempting to line up an 18 inch pipe elbow. EE placed his left arm between the pipe elbow and a bracket as the elbow was being lowered resulting in his arm being caught between the pipe elbow and the bracket.
Employee lost footing coming off 993 loader ladder and fell approximately 4 feet landing on left shoulder
Employee operating crane stepped off 3"" drop in flooring and hyper extended R knee.
Employee was shoveling and hit the idler table beam jamming his R wrist.
Employee's foot slipped off the step when dismounting the rubber tire and cut her R knee.
Trackhoe was pulling 4"" HDP pipe out of ground and it was hung up so employee was freeing it with a shovel and the pipe sprung up out of the ground striking him in the left leg causing a knee strain.
Employee slipped off headerline while changing valve and strained his left knee
Employee pushing cart with stacked metal when a piece of metal fell off slicing his right thumb.
Employee was moving gas bottles from carrier to storage rack when he tipped one over and it landed on his knee causing a cruise on his left knee
Employee opened the upper cabinet in the restroom and pulled the entire cabinet off the wall striking her in the head.
Employee was gapping crusher when she took a step back and her foot got caught on some metal falling backwards breaking her fall with her arm.
Employee got slurry in his eyes when he walked by the slurry tank vent pipe.
Employee strained shoulder when climbing ladder onto dozer
Employee was climbing onto drill when he moved the handrail it came loose and cut his finger
Employee was jolted in haul truck while being loaded with material and strained her back
Employee was using a cordless hand drill in an awkward position and the drill got caught up on a piece of metal snagging the drill and quickly twisting his arm.
Employee was filling a container with oil when the air powered pump hose broke and sprayed oil in employee's face and eyes.
Employee working in tunnel got overheated and dehydrated. Heat Stroke
Employee was shoveling and wheeling wheel barrow and experienced numbness and tingling down right leg and foot.
Employee was leaning over to get something and fell on his knee cap
During first responder training the employee was changing O2 bottle on SCBA in bent over position and when he stood up with this SCBA pack on his back he felt a strain in his groin.