CENTRAL SHOPS Metal/Non-Metal

EMPLOYEE WAS LIFTING A PORTAL POWER (78LBS) ONTO THICKENER DRIVE FELT A BURNING SENSATION IN ABDOMEN RADIATING TO HIS BACK BEGAN VOMITING WENT HOME FROM WORK BUT HIS WIFE BROUGHT HIM TO HOSPIT AL HAD EMERGENCY SURGERY FOR HERNIA

EE WAS PAINTING A 12" X 20' CHANNEL IRON. HE ATTEMPTED TO ROLL THE STEEL OVER TO PAINT THE OTHER SIDE USING A STEEL PRY BAR. THE STEEL ROLLED BACK ON HIS RIGHT FOOT CAUSING A BRUISE ON THE MET ATARSAL AREA.

EMPLOYEE WAS INSTALLING A HOIST RELEASE CABLE IN THE CAB OF 65-TON CRANE. HE WAS WORKING ON HIS HANDS AND KNEES IN A TIGHT AREA AND HE FELT A PULL IN HIS BACK.

WHILE INSTALLING SIDE PLATES ON 8' VIBRATING SCREEN, EMPLOYEE TWISTED HIS BODY WHEN LIFTING IN IN PLACE. HE TWISTED HIS LEFT KNEE. CONTINUED TO WORK UNTIL JULY 8, 1994. SCHEDULED FOR KNEE SURG ERY JULY 11, 1994.

TWO EMPLOYEES WERE WELDING INSIDE OF A TROMMETL & THE FLASH FROM WIRE FEED WELDER BURNED ATHE RIGHT NECK & EAR.

EMPLOYEE WAS ASSISTING WELDER BY HOLDING METAL RINGS TOGETHER FOR JACK WELDING HE RECEIVED ARC FLASHES TO HIS LEFT EYE

CARPAL TUNNEL SYNDRONE. SURGERY SCHEDULED FOR 7/18/93.

EMPLOYEE WAS HELPING EMPLOYEE LIFT 4" CHANNEL ONTO THE SAW. HE SLIPPED ON PIPE LAYING ON FLOOR, CAUSING HIM TO TWIST AND FELL TO THE FLOOR. HE STRUCK HIS RIBS ON STEEL RACK AS HE FELL. HE HAD SORE RIBS AND SORE LOWER BACK.

INJURED WAS BEING TESTED ON BRODEX MACHINE BY U.S. BUREAU OF MINES PERSONNEL (HEALTH STUDY). AFTER FIRST SESSION, HE FELT PAIN IN HIS ABDOMEN. ON HIS SECOND ATTEMPT, HE FELT ACUTE ABDOMINAL PAIN.

EMPLOYEE WAS MOVING LOAD ON JIB CRANE, WHILE PULLING THE LOAD, HE SLIPPED ON A WELDING ROD, (DID NOT FALL) TWISTING HIS BACK. REPORTED A SORE BACK, BUT INJURY DID NOT REQUIRE TREATMENT UNTIL 7 /9/93 WHEN HE WAS AUTHORIZED TO SEE A DOCTOR.

WHILE REMOVING A BABBIT BEARING, THE PLUG SLIPPED OFF THE METAL AND THE HAMMER STRUCK HIS FINGER AGAINST THE END BALL.

EMPLOYEE WAS MACHINING A PIECE OF 5 1/2" ROUND STOCK 36" LONG. HE WAS ROLLING THE STOCK BY HAND IN A V-BLOCK. WHILE ROLLING THE STOCK, IT BEGAN CLIMBING OUT OF THE V-BLOCK. HE TRIED TO STOP TH E PIECE FROM FALLING BUT DUE TO THE WEIGHT (APPROX 250 LBS) HE WAS UNABLE TO STOP IT. IT CAUGHT HIS FINGERS BETWEEN THE MACHINE BED AND THE STOCK.

LOCATION-MACHINE SHOP. EMPLOYEE WAS USING A 3'6" LONG PIECE OF EMERY DAPER TO POLISH A SHAFT. HE WASN'T USING THE MIDDLE OF THE PAPAER, BUT THE END. THE PAPER WRAPPED AROUND THE SHAFT CATCH ING HIS GLOVE AND PULLING HIS HAND INTO THE BED THE MACHINE. INJURED WAS BROUGHT AND TO BELL HOSPITAL EMERGENCY ROOM FOR MEDICAL TREATMENT. CONTUSION TO RIGHT HAND.

INJURED WAS POLISHING 1" SHAFTING IN LATHE AND WAS WEARING GLOVES. EMERY CAUGHT AND PULLED FINGERS INTO PIECE. THIRD AND FOURTH FINGERS ON RIGHT HAND WERE DISLOCATED AND BRUISED. HE WAS TAK EN TO HOSPITAL FOR TREATMENT.

REMOVING BURNER MOTOR FROM #2 BOILER MATHER A USING MANUAL CHAIN HOIST. HOIST WAS HUNG FROM PIPE INSERTED IN BOILER TUBE. EMPL WAS OPERATING HOIST FROM STAIR PLATFORM AND GAVE SLACK TO LOWER B MOTOR TO FLOOR. PIPE MOVED OUT OF TUBE AND STRUCK EMPL ON LEFT SIDE OF HEAD. CUTS TO EAR REQUIRING MEDICAL ATTENTION AT BELL HOSPITAL EMERG RM.

INJURED WAS OPERATING SUB/ARC WELDER WELDING A PULVERIZER ROLL.SILVER GLASS FLEW INTO HIS EYE(RIGHT)WHILE HE WAS STANDING APPROX 6' FROM PULVERIZER ROLL.INJURED WAS BROUGHT TO BELL MEMORAIL HO SPITAL FOR TREATMENT TO HIS EYE AND THEN RETURNED TO WORK.

EE WAS LINING UP A PULLEY IN THE L-101 LATHE WHILE ROTATING THE CHUCK BY HAND AND WATCHING THE DIAL INDECIATOR HE PINCHED HIS RIGHT RING FINGER BETWEEN THE CHUCK AND THE TOOL STEAD REST. THE O RIGINAL DIAGNOSIS OF HIS INJURY WAS SOFT TISSUE INJURY BUT UPON REEXAMINATION ON 10-12-92 IT WAS DISCOVERED THAT HIS FINGER HAD A SMALL FRACTURE HENCE THE DELAY IN FILING THIS REPORT.

HE WAS REMOVING A CARTON OF KIMWIPES FROM A STACK OF CARTONS ON A PALLET. THE CARTON WAS ABOUT 7 1/2 FEET OFF THE FLOOR AND WEIGHED ABOUT 30 LBS. WHILE REMOVING THE CARTON HE EXPERIENCED A PAI N IN THE CENTER OF HIS UPPER BACK. HE BEGAN TO LOSE TIME ON 9-17-92.

MOVING WHEEL EXPER PAIN IN LOWER BACK

PICKING UP PC OF STEEL PLATE EXPER PAIN INLOWER BACK

LOADING GRATE WHEEL IT SLIPPED OUT OF CHUCK PINCHED R FOREARM

EE WAS USING A LARGE PLATE SHEAR TO REMOVE 1/2INCH PIECE OF ONE SIDE OF 1/4 X 1 X1 AGNLE IRONS. HE HAD COMPLETED 516 PIECES AND WAS WORKING ON THE LAST ONE WHEN HE FAILED TO REMOVE HIS HAND AF TER POSITIONING THE PIECE. WHEN HE ACTIVATED THEFOOT PEDAL ONE OF THE HOLD DOWN PADS PINCHED HIS LEFT LITTLE FINGER.

EE WAS USING A VERTICLE HYDRAULIC PRESS TO PRESS OUT AN OLD BUSHING FROM AN IDLER. WHEN THE BUSHING WAS ALLMOST OUT HE REACHED IN BEHIND THE GUARD DOORS TO CATCH THE PUSHER BLOCK BEFORE IT FEL L. AT THIS TIME THE LOWER PORTION OF THE CYLINDER CASTING BROKE OFF AND THE CASTIN AND OR THE PISTON SPRING STRUCK HIS LEFT HAND.

INJURED HAD FILLED A 5 GAL PAIL WITH WATER,AND AS HE PICKED UP THE PAIL TO CARRY IT TO THE DRILL HE EXPERIENCED A PAIN IN HIS RIGHT SHOULDER AND RIGHT SIDE OF HIS NECK.WGT 40# MAX.INJURED BEGA N TO LOSE TIME ON WED 03-18-92.

I NAME WAS WALKING ALONGSIDE A LOW-BOY TRAILER THAT WAS PARKED IN THE WELD SHOP HE CAUGHT HIS LEFT FOOT BETWEEN A TIRE ON THE LOWBOY & A LARGE TIMBER ON THE SHOP FLOOR TWISTING HIS LEFT KNEE I NAME CONTINUED WORKING UNTIL 03-24-92 & BEGAN TO LOSE TIME ON 03-25-92

INJURED'S FOOT SLIPPED OFF THE EDGE OF A WOODEN FLOOR MAT(DUCKBOARD) WHICH WAS ABOUT 1 1/2" HIGH.HE EXPERIENCED A PAIN IN HIS LOWER BACK.INJURED BEGAN TO LOSE TIME ON 12-31-91.

INJURED WAS WALKING THOUGH THE #19 SHOVEL HOUSE(AT EMPIRE MINE) WHEN HE STRUCK HIS RIGHT KNEE ON A PIPE PLUG.INJURED CONTINUED TO WORK UNTIL 12-27-91 AND BEGAN TO LOSE TIME ON 12-30-91.

INJURED WAS BENDING OVER TIPPING UP A ROLL OF BANDING TAPE(60# 3/4" METAL TAPE) PREPARATORY TO PUTTING THE ROLL ONTO THE BANDING MACHINE.HE WAS NOT LIFTING THE TAPE ONLY TIPPING IT UP TO A VER TICAL POSITION.

I.NAME MACHINING PUMP SHAFT.LONG METAL STRING WAS COMING OFF SHAFT,PUT LEATHER WORK GLOVES ON AND BROKE STRING,IT SLICED THROUGH GLOVES CUTTING RIGHT INDEX FINGER.

I NAME HAD BEEN CUTTING GRASS & WEEDS FOR APPROX 5 HRS WITH A SNAPPER WEEDEATER TRIMMER AT THE END OF THE SHIFT HE COMPLAINED OF A SORE BACK UNIT WEIGHS ABOUT 20#

HE WAS CLEANING UP SMALL PIECES OF SCRAP METAL BEHIND THE METAL SHEARS. AS HE BEGAN TO STRAIGHTEN UP HE EXPERIENCED A PAIN IN HIS LOWER BACK.

I NAME WAS DRILLING A HOLE IN A STEEL PLATE METAL SHAVINGS WERE WINDING AROUND THE DRILL BIT & AS I NAME ATTEMPTED TO REMOVE THE SHAVINGS ONE OF THE SHAVINGS CUT HIS LEFT INDEX FINER HE WAS WE ARING LEATHER WORK GLOVES AT THE TIME

HE WAS LEAVING THE WLED SHOP VIA THE NORT MANDOOR. HIS FOOT SLIPPED ON THE ICE. HE DID NOT FALL BUT WHEN HE CAUGHT HIMSELF HE EXPERIENCED A PAIN IN HIS LOWER BACK. THE ENTIRE AREA WAS SLIP PERY DUE TO A RAINFALL ON FRIDAY 3-1-91. THE AREA HAD BEEN SANDED PRIOR TO THE START OF THE SHIFT.

HE STRUCK HIS RIGHT KNEE AGAINST A MOTOR GUARD ON THE LATHE HE WAS OPERATING. HE CONTINUED WORKING UNTIL FRIDAY 12-14-90. ON 12-16-90 HIS KNEE WAS QUITE SORE SO HE WENT TO THE EMERGENCY ROOM

HE AND HIS PARTNER WERE SPREADING 10 CU. YDS. OF REDI-MIX CONCRETE, POURING A CONCRETE PAD FOR A BUILDING. AT THE END OF THE SHIFT, HE COMPLAINED THAT HIS BACK WAS SORE.

I NAME WAS CLEANING UP HIS EQUIPMENT AFTER INSTALLING AN AIR DUCT AS HE REACHED DOWN TO PICK UPA 6FT FIBERGLASS STEPLADDER HE EXPERIENCED A PAIN IN HIS LOWER BACK

HE AND HIS PARTNER WERE ASSEMBLING DUCTWORK IN THE SHEETMETAL SHOP. HIS PARTNER WAS GRINDING ON A WELD AND HE FELT SOMETHING ENTER HIS LEFT EYE. HE WAS WEARING SAFETY GLASSES WITH SIDE SHIELDS AT THE TIME OF THE INCIDENT.

I.NAME AND HIS PARTNER WERE PRESSING BUSHINGS OUT OF GRATE RETURN ROLLERS. THE ROLLERS WEIGHED ABOUT 80# EACH, SO TWO MEN WERE ASSIGNED TO THE JOB. I.NAME WORKED ON SAT 3/17/90 BUT DID NOT REP ORT ANYTHING TO HIS SUPERVISOR. ON MONDAY AM 3/19/90 HE CALLED COMPLAINING OF A SORE BACK AND FELT THAT HANDLING THE ROLLERS WAS THE CAUSE OF THE DISCOMFORT HE WAS EXPERIENCING.

I.NAME REPAIRING CONVEYOR HEAD PULLEY.PULLING ON WRENCH EXPERIENCED PAIN IN GROIN.CONTINUED WORKING UNTIL BEGAN LOSING TIME 5-14-91 AND HAS SURGERY SCHEDULED 5-23-91

EMPL WAS PULING MOTOR FIELD COIL INTO SOTRAGE ROOM WHEN HE EXPERIENCED PAIN IN LOWER BACK. COIL WEIGHS APPROX 90#. FLOOR WAS SMOOTH CONCRETE & FREE OF OBSTRUCTIONS.

INJURED WAS TURNING A CONTROL LEVER ON AN ELECTRICAL PANEL TO THE OFF POSITION WHEN HIS LEFT INDEX FINGER WAS PINCHED BETWEEN THE HANDLE AND THE LOCK-OUT BRACKET.

EMPL WAS GUDING & HOLDING TENSION ON HOIST CABLE FOR O HEAD CRANE SO CABLE WOULD WRAP ONTO DRUM CORRECTLY. LEFT INDEX FINGER WAS DRAWN INTO POINT SHEAVE & PINCHED.

EMPL WAS STEPPING OUT OF DISPATCHER SHACK THAT HE WAS CONSTRUCTING. AS HE STEPPED ON METAL BEAM FOOT SLIPPED HE EXPERIENCED PAIN IN LOWER BACK.

CHAIN SAW KICKED BACK WHILE SAWING OFF A TREE BRANCH SORE SHOULDER.

COUPLING BROKE ON STEAM CLEANING WAND, & STEAM TBURNED LEFT FOREARM.

I.NAME PASSING SLING UNDER ROTOR AND LEFT RING FINGER WAS PINCHED BETWEEN SLING HOOK AND ROTOR.

EMPL WAS STEPPING FROM PITMAN CRANE TRUCK TO LOW BOY TRAILER TRACTOR. UNITS WERE SIDE BY SIDE AS HE STEPPED CRANE OPER. MOVED TRACK CRANE FORWARD & EMPL WAS PINCED BETWEEN TRUCK CRANE & OPER. CAB DOOR OF TRAILER TRACTOR.

THE INJURED WAS PULLING ON A WRENCH TO LOOSEN A COUPLING.WHEN THE COUPLING SUDDENLY LOOSENED HE EXPERIENCED A PAIN IN HIS NECK.

I,NAME WAS WELDING WHEN ANOTHER EMPLOYEE PT A PIECE OF HOT EQUIPMENT INTO A CONTAINER OF LOOSE INSULATION THAT IS USED TO CONTROL THE COOLING POROCESS. SOME OF THE LOOSE MATERIAL GOT ON HIS SL IM AND AT THE END OF THE SHIFT HIS SKIN WAS ITCHING AND BEGINGING TO RASH.

HE STRUCK HIS HEAD AGAINST A RUBBER LINED SUPPORT PIPE WHILE INSTALLING BOLTS IN THE SIDE PLATE OF A SHAKER SCREEN. HE COMPLANNED OF SORE NECK.

I.NAME WAS CONNECTING A 600 AMP WELDER. HIS FOOT SLIPPED AND HE TWISTED HIS RIGHT KNEE.

EMPL WAS PULLING DOOR SHUT & HE PINCHED 3RD FINGER OF RT HAND BETWEEN EDGE OF DOOR & DOOR JAMB.

HE HAD FINISHED TIGHTENING THE NUT ON THE ALORI'S TOOL POST WITH A BOX END WRENCH. HE STRUCK THE WRENCH AND IT FLIPPED OFF THE NUT STRIKING HIM IN THE MOUTH CHIPPING HIS FRONT TOOTH.

I NAME WAS HELPING TO MOVE A NEW BOILER SECTION INTO PLACE THE SECTION MOVED UNEXPECTEDLY STRAINING HIS LEFT ELBOW.

I.NAME PINCHED HIS LEFT LITTLE FINGER BETWEEN 2 CO2 TANKS WHILE PLACING TANKS ON STORAGE RACK

I.NAME DROPPED A PIECE OF ROUND STOCK ON THE FLOOR AS HE BENT OVER TO PICK UP THE PIECE HE STRUCK HIS HEAD ON A HYD.PRESS

INJ WAS USING A PC. OF 3/4" PLYWOOD AS A STAGE PLANK THE PLYWOOD BROKE HE FEL STRIKING HIS LEFT BUTTOCK AGAINST AN ANGLE IRON BRACKET.

EMPL WAS REMOVING WORN GRIZZLY BAR SECTIONS (75-804) WHEN HE EXPERIENCED PAIN IN HIS LOWER BACK.

HE WAS DISCONNECTING LEADS IN A 440 V MOTOR CONTROL CENTER. HE THOUGHT THE UNIT WAS DE-ENERGIZED BUT IT WASN'T. HIS PLIERS SHORTED ACROSS THE LEADS RESULTING IN HIS BEING BURNED.

HE STRUCK HIS RIGHT THIGH AGAINST THE EDGE OF A PIECE OF STEEL PLATE CAUSING A PAIN ON HIS LOWER BACK.

HE WAS LIFTING A WOODEN PAD TO PLACE IT UNDER THE CRANE OUTRIGGER AND WHEN HE EXPERIENCED APAIN IN HIS UPPER BACK.

I.NAME WAS SHEARING 4 X 8 SHEETS OF STEEL INTO SMALLER PIECES HE WAS USING A OVERHEAD CRANE FOR THE LARGE PIECES AND HANDLING THE SMALLER PIECES BY HAND AT THE END OF THE SHIFT HE COMPLAINED O F A SORE LOWER BACK THERE WAS NO SLIP TRIP OR FALL INVOLVED

I.NAME WAS REWINDING A 50 HP ELEC MOTOR AND WAS TRIMMING THE PHASE PAPER HE MOVED A GROUP OF LOOSE WIRES ASIDE WHEN ONE OF THE WIRES BROKE LOOSE AND STRUCK HIS LEFT EYE

I.NAME WAS WALKING BY T HE TESTIARY CRUSHER KHYDRAULIC TANK & PUMP STAND ON THE REPUBLIC MINE SECONDARY CRUSHER BLDG.HE STRUCK HIS LEFT KNEE AGAINST THE METAL TANK STAND HE WAS ENTERING A DARK AREA FROM THE OUTSIDE OF THE BLDG.

THE INJURED HAS3EXPERIENCED PAIN IN HIS RIGHT HAND FOR 2-3 WEEKS. ON 02/11/88 HE VISITED THE MINE NURSE WHO RECOMMENDED THAT HE SEE A DOCTOR.THE DOCTOR DIAGNOSED CARPAL TUNNEL SYNDROME AND TH AT IT IS WORK R9LATED.SURGERY IS SCHEDULED.

I NAME WAS MOVING A CAST IRON HOUSING SO HE COULD CLEAN UP HIS WORK AREA. THE EXPERIENCED PAIN IN RT SIDE. THE HOUSING WEIGHED APPROX 50# THERE WAS NO SLIP OR FALL INVOLVED. HE VISITED OUR DR ON 2 19 88 AND WAS PLACED ON LIGHT DUTY FOR APPROX 3 WEEKS

HE WAS REPORTED3THAT DURING THE SHIFT HE HAD TO PERIODICALLY BEND OVER TO OBSERTVE WIRE FEED WELDING MACHINE. AT THE END OF THESHIFT HE COMPLAINED OF A SORE BACK. THERE WAS NO SLIP OR FALL I NVOLVED AND NO 5IFTING INVOLVED.

I.NAME WAS HOOK3NG UP A CHAIN SLING TO A LIFTING EYE ON A DRAY THE CRANE OPERATOR MOVED THE CRANE AND HIS LEFT MIDDLE FINGER WAS PINCHED BETWEEN HOOK AND DRAY RUNNER POOR COMMUNICATION BETWEEN CRANE OPERATOR3AND HELPER

HE HAD BEEN LIF7ING RAKE SECTIONS WITH HIS PARTNER (WT 60 LBS). LATER HE BENT OVER TO PICK UP A STRAIGHT-EDGE OFF OF FLOOR, WHEN HE EXPERIENCED A PAIN IN HIS LOWER BACK.

I.NAME REPORTED3THAT HE EXPERIENCED A PAIN IN HIS LOWER BACK AS HE LIFTED HIS TOOL BOX (WT.30#) INTO BOX OF A TRK.HE HAD TO LIFT THE BOX APPROX.4102FT OFF THE GROUND

I.NAME MOVING S9CTION OF SAFEWAY SCAFFOLDING SLIDING IT ALONG FLOOR AND HE STEPPED INTO OPEN MANHOLE INJURING LEFT KNEE.

HE WAS ATTEMPTI3G TO CUT SOME CARDBOARD FROM A TUBE WITH A POCKET KNIFE. HE WAS PUSHING THE POINT OF THE KNIFE INTO THE CARDBOARD WHEN THE BLADE CLOSED AND CUT HIS RIGHT INDEX FINGER.

HE WAS REMOVING3CHIPS AND SHAVINGS FROM UNDER HIS LATHE. AS HE PULLED ON SOME SHAVINGS HE CUT THE TIPS OF HIS FINGERS. HE WAS NOT WEARING GLOVES AT THE TIME. HE WAS USING A PAIR OF PLIERS T O REMOVE THE SH5VINGS AND CHIPS.

HE WAS DRILLING3A 3/4" HOLE IN A PIECE OF STEEL WITH A VETICAL DRILL PRESS.DRILL BIT STUCK IN THE STEEL..HE SHUT THE DRILL OFF TO ATTEMPT TO FREE THE BIT.WHEN HE TURNED THE DRILL ON AGAIN, TH E BIT BROKE AND3THE PIECE OF STEEL FLEW OFF THE TABLE STRIKING HIM IN THE RIGHT GROIN.

I,NAME WAS FIGH7ENING BOLTS WHITH A 9/16" SOCKET & RATCHET WRENCH. HE EXPERIENCED A CRAMP IN HIS NECK. THE PAIN DISSAPPAVED IN A VERY SHORT TIME, BUT WAS DIZZY & HAD TROUBLE MAINTAINING HIS BALANCE. 3

I.NAME'S FOOT S5IPPED OFF A BAR GUARD WHILE WORKING ON A CONVEYOR DUST COLLECTOR DUCT. HE FELL STRIKING HIS RIGHT RIB CAGE AGAINST A HANDRAIL.

I NAME LEFT SLE9VE CAUGHT ON ROTATING PIECE IN A LATHE. HIS ARM WAS PULLED AGAINST THE PIECE RESULTING IN MULTIPLE LACERATIONS A CONTUSIOUS TO LEFT FOREARM.

I NAME SENT OVE9 TO PICK UP A PARTS PAIN WHEN HE EXPERENCE A PAIN IN HIS LOWER BACK. THERE WAS NO SLIP OR FALL INVOLVED THE PARTS PAN WEIGHTED ABOUT 25 LB.

I.NAME WAS BEGI3NING TO OUT A PIECE OF BAR STOCK. HE FAILED TO CLAMP DOWN THE PIECE. THE PIECE MOVED & HE PINCHED HIS LEFT INDEX FINGER BETWEEN THE PIECE HE WAS CUTTING3& ANOTHER PIECE OF TUBING ON THE TABLE.

I NAME WAS LIFT3NG A 100 LB BAG OF FLUX TO DUMP INTO A HOPPER ABOUT 3 1/2 INCH ABOVE THE SHOP FLOOR. HE EXPERIENCED A PAIN IN HIS LOWER BACK.

I,NAME WAS WALK3NG ACROSS PARKING LOT TOWARD CHANGE HOUSE PRIOR TO HIS SHIFT. SLIPPED & FELL SPRAMMING LEFT WRIST. VERY SLIPPERY CONDITIONS. ABOUT 27F & DRIZZLING. LOT WAS PROWED & SANDED PRIO R TO 6:30AM. 3

I NAME WAS ROLL3NG A LARGE BEARING OVER ON THE SHOP FLOOR. HE EXPERIENCED A PAIN IN HIS LOWER BACK. THERE WAS NO SLIP TRIP OR FALL INVOLVED IN THE ACCIDENT.

I,NAME WAS WELD3NG BLOCKS ON THE LIP OF A SHOVEL BUCKET. AS HE LEANED OVER TO BEETTER POSITION HIMSELF, HE STRUCK HIS LEFT ELBOW ON ONE OF THE WELDER BLOCKS.

I.NAME WAS USIN1 A CHUCK WRENCH TO TIGHTEN THE CHUCK ON HIS LATHE. HE EXPERIENCED A PAIN IN HIS RIGHT SHOULDER WHILE PULLING ON THE WRENCH.

I.NAME WAS RETU9NING TO WELD SHOP AFTER EATING LUNCH HIS RT FOOT SLIPPED OFF STEP HE EXPERIENCED PAIN IN HIS UPPER RT LEG HIP AREA HE DIDNOT FALL STEPS WERE IN GOOD SHAPE & HANDRAILS WERE PROV IDED NOTE I.NAM9 BEGAN LOSING TIME ON 122385

WHILE ATTEMPTING TO TURN MOTOR SHAFT USING THE DRIVE PINION, THE INJUREDS FINGERS BECAME LODGED BETWEEN THE PINION AND PINION GUARD.

THE INJURED WAS USING A STRIP OF EMERY CLOTH TO CLEAN UP A SHAFT, THAT WAS TURNING ON A LATHE. THE EMERY CLOTH GRABBED ONTO THE SHAFT AND PULLED OUT OF HIS HAND CUTTING HIS SEFT PALM. TWO CUTS (5 C.M. AND 2 C.M.) IN LEFT PALM.

THE INJURED WAS WALKING THRU THE YARD TO THE COMPRESSOR ROOM WHEN HE SLIPPED ON THE ICE.

INJURED WAS PULLING A LARGE WHEEL OFF SHAFT WITH PORTA POWER AND PULLER. HE WASSTANDING BETWEEN THE NON-WORKING ARMS OF PULLER WHEN THE SAFETY CHAIN HOOK BROKE AND THE ARMS SLIPPED OFF THE WHE EL BENG PULLED PINCHING HIM BETWEEN THE ARMS OF THE PULLER.

INJ WAS IN THE PROCESS OF ALIGNING AND BALANCING AN MG SET TEMPORARY WEIGHTS WERE BEING TAPED ON A WEIGHT BROKE LOOSE AND STRUCK HIM IN T HE CHIN AND NECK

INJ EMP WAS DISASSEMBLING AN WXCITER HE WAS PRYING ON THE BEARING CAP USING A 24 IN PRY BAR THE BAR SLIPPED AND STRUCK HIM ABOVE THE LEFT EYE 4 STITCHES WERE REQUIRED

INJ WAS IN PROCESS OF INSTALLING WORK PIECE IN LATHE CHUCK HE HAD A PIPE EXTENSION ON WRENCH HANDLE PROBABLY ENGAGED 1 OR 2 INCHES PIPE SLIPPED OFF WRENCH INJ LOST HIS BALANCE HIS WRIST CONTAC CONTACTED SHARP EDGE OF MATERIAL STACKED BY LATHE 3 SUTURES

INJURED WAS ON THE ROADWAY HIS RIGHT FOOT SLIPPED OUT FROM UNDER HIM AS HE CAUGHT HIS BALANCE HE WRENCHED HIS BACK HE CONTINUED WORKING THE REST OF THE SHIFT