Amrize Presque Isle Aggregates Metal/Non-Metal

Two millwrights were trying to remove a metal plate from the conveyor by inserting pry bars. As the part broke free, EE's hand was pulled with the pry bar and pinched between the bar and the conveyor roller assembly causing a fracture of the distal phalanx of the left little finger.

(1st day of Treatment 1/13/23) Bending over to tie in the shot and felt low back give out.

While cleaning material out from under Conveyor S4 employee pinched the tip of right pinky finger between the handle of the shovel & the leg of the conveyor causing a small cut that required glue to close.

While changing a bit on the DTH drill a supplier was unscrewing the chuck and bit from the bottom of the hammer, the bit slipped and while trying to stabilize it the supplier's small finger moved in between the chuck and the top shoulder of the bit. The chuck came down on the smallest finger of the left hand causing a laceration under the glove.

Employee was attempting to pull a section of belt back together with a chain puller for a splice. Because the belt was under tension the handle pulled hard, due to slack in the belt it very quickly went much easier causing the handle to loosen, when that happened it slammed down and pinched right thumb between the handle and the chain. This broke the nail and cut the thumb.

The employee was blowing the chutes on the first floor screens. As employee was doing this task EE had piece a dirt get in EE's eye. EE was wearing all PPE including safety glasses.

Employee was shoveling near the tail section of D7A conveyor, the shovel made contact with a steel shim under the structural channel of the conveyor, the sudden/abrupt stop caused the shovel to twist to the left. This twisting motion combined with the force applied caused the employees knee to "give out" or buckle in a sideways motion.

Employee was attempting to remove snow and ice from between the wheels of a radial stacker. The employee was working from an elevated position due to built up material (snow/ice/sand mix), this awkward position likely caused an overexertion and led to the employee's back "locking up."

Employee was operating a haul truck in adverse weather conditions (extreme freeze/thaw) that caused the haul roads to become rougher than normal. The employee experienced lower back pain.

Miners were working to clear the jammed primary gyratory crusher. 2 miners were working to remove stone from the bowl, one miner was working farther down in the bowl using an air hammer to break up a large rock when suddenly another rock became dislodged and pinned the miner's feet down, several rocks and finer material slid down as well entrapping the employee below the knees.

Miner was carrying a piece of debris when ee tripped over an outstretched hose and dropped down to one knee.

Employee sustained a hernia as a result of lifting a machine component weighing 100 lbs.

Dozer operator was ripping on the quarry floor with a CAT D-10 when they hit a large rock, due to the nature of the ripped material the dozer was on uneven ground and the employee jarred their neck and mid back due to the side to side motion. The employee was diagnosed with a neck strain and thoracic back pain, they were prescribed medication and given modified work duty.

Operator was loading a production haul truck with a large wheel loader. As EE backed away from the truck (bucket still in the air), EE drove over a basketball size rock that had unknowingly rolled behind loader. Right after EE drove over the rock, the employee experienced pain in back.

While chipping material build in chute, a portion of the material fell in front of the employee, causing them fall backward and striking head/helmet agianst the opposite wall. Employee lost conscious for a minute. EE's work partner helped EE exited the chute under their own power. EE and partner reported immediately to their supervisor and first aid was provided

Employee slipped on the ice and noticed soreness in shoulder and was instructed to administer self-care. Employee was placed on restricted duty after MRI on 2/23/16. During the week of February 22nd all hourly employees were laid off, this information was received 2/26/16 and employee returned to work on 2/29/16 on restricted duty.

Employee was flipping a gate in front of a screen when his finger became pinched. Resulting injury was a fractured thumb.

Employee was cleaning loader windows when several towels blew out of his hand. As he tried to grab the towels he came into contact with the emergency gate on the side railing which caused the latch to disengage. The employee fell through the gate to the ground resulting in a knee injury. Employee was on home health care until 10/8/15 when he was prescribed a pain killer.

Employee was lifting a tool box onto a truck (with the assistance of another employee) and felt a spasm in his back. Employee was on home health care until 9/28/15 when a muscle relaxer and pain killer were prescribed.

While haul truck operator (injured party) was being loaded a large boulder that was in the bucket of the loader hit the empty box and severely rocked the truck causing a neck strain. Re-classified from First Aid to Medical on 10/31/14 due to professional care by chiropractor.

While dismounting a work platform the employee's glove caught on the ladder's safety chain hook. He had not noticed his glove had snagged on the hook and when he stepped down the sudden unexpected jerk strained his left shoulder. This injury became a lost time Incident as of 12/7/15 due to surgery, prior to that employee was not restricted.

WHILE USING A COME-A-LONG TO LIFT THE C-7 FEED CHUTE, ONE OF THE EYE BOLTS BEING USED, BROKE. THUS CAUSING THE SHACKLE AND/OR EYE-BOLT TO HIT ee IN THE FOREHEAD. THE EMPLOYEE WAS DRIVEN TO CLINIC FOR MEDICAL ATTENTION IN WHICH HE RECEIVED 6 STITCHES. NO PRESCRIPTION WAS GIVEN AND THERE WAS NO LOST TIME.

IN FEEDER PAN ON A 4 FT. LADDER. HE REACHED UP TO HOOK A COME-A-LONG ON SIDE OF FEEDER.HE WAS MORE THEN HALF WAY DOWN THE LADDER,HIS FOOT THEN SLIPPED OFF & INSTEAD OF FALLING OVER, THE EMPLOYEE HELD ON TO A NEARBY PIPE.WHILE SUSPENDED IN AIR, HE SPUN AROUND THUS STRETCHING SHOULDER & BICEP. POTENTIAL LOST TIME IN THE FUTURE.

The employee reported soreness in upper back while operating a loader, the soreness occurred on a Wednesday his 3rd shift. On the following Monday, the employee was placed on modified light duty until the soreness can be investigated further. There was no specific event that occurred to cause the soreness.

Employee operating Front End Loader. Digging to create a floor in New Development, hit a hard spot that was not noticeable causing the Loader to stop abruptly, jarring the employees neck. He did home health care for neck until 7/29/13 when conditions worsened. On 7/29/13 the employee was put on restrictive duty and given a prescription.

WALKING DOWN STAIRS, BEGAN TO FALL FORWARD, WHILE HANGING ON TO THE RAIL HE PULLED BACK W/HIS LEFT ARM TO CATCH HIMSELF & HEARD A POP & FELT A STRAIN IN HIS ARM. Re-notification in Dec, 2013 - 2nd opinion confirmed work related.

Back strain while operating drill. Sitting in twisted position for 2 hrs - didn't realize seat swiveled. Found release knob on side of seat & rest of shift the seat swiveled. However, some back discomfort at end of shift. 2 days later, he reported increased back pain, sought medical attn & was prescribed a Rx & light duty.

While employee was walking around the pickup at the work site location he slipped in the fresh wet snow and fell to the ground. He didn't hit anything on his way down. But did feel his Left ankle twist during the fall.

Employee was welding on the boat-loader catwalk, in the shop. He was wearing his welding helmet & safety glasses. He raised his welding helmet while grinding the slag off the weld when a piece of foreign material got past his safety glasses and into his eye.

EE states while working on a bank with a loader and eating peanuts he jarred himself and bite his bottom lip. Cut on lip was found to be substantial and 8 stitches were required to close the wound. EE also complained of being sore on his right side and arm from being jarred against the arm rest. X-ray showed that he had fractured a rib.

Employee was pushing a cart in a tunnel when his right foot slipped in some mud, causing him to abruptly shift his weight onto his left hip. On 09/01/2011, employee sought treatment for discomfort in his lower back and hip. On 11/04/2011, an Independent Medical Exam found that the incident occurring on 04/06/2011 exasperated the employee's pre-existing osteoarthritis.

Employee was stepping over a water pipe, tripped, fell, and landed on some stones causing a minor abrasion and a bruise. On 12/21/2010, the employee notified the plant manager that he had sought treatment on 12/09/2010. On 12/21/2010 our company doctor found the employee's injury to be infected. He received a tetanus shot, prescription medication, and a follow-up 12/29/2010.

Person was driving a pickup to the primary to pick up employee. He went around the corner at the ramp on the wrong side of the road. The sun was in his eyes and he ran head on into another pickup coming from the primary.

Person was driving a pickup to the primary to pick up employee. He went around the corner at the ramp on the wrong side of the road. The sun was in his eyes and he ran head on into another pickup coming from the primary.

The employee was walking to a truck and slipped on the sand covered ice, catching himself and not falling to the ground.

Employee claims back/lumbar strain as he exited his bulldozer, or while operating it.

Employee was pulling 1/2" overlay screen up the screen to the position it. He was using the screen puller tool. Strain to back. He reported it the day it happened but did not seek medical attention until 10/21.

Emp. was loading haul trucks - he had just dumped a bucket in a haul truck and was backing away, lowering the hoist at the same time, the hoist did not respond so employee moved the lever forward and the bucket dropped and struck the ground. Emp. did work that full shift and worked next two scheduled shifts - he then went to the doctor on 5/17 - and the doctor took him off work.

Employee was checking pump in pumphouse, when unexpected 40 mph+/- wind blew the pumphouse door shut onto employee's fingers while they were exposed in the door jam pinch point.

Injured was drilling wear plate and brushed chips away with hand while wearing gloves. Spiral chip from rotating drill snagged glove and cut through it, cutting middle finger on right hand. Required 9 stitches.

Employee was attempting to reach for trouble light above conveyor when his right hand was pulled into the pinch point between belt and the idler. Resulted in open wound with fractures to right hand, wrist and all five digits.

Employee slipped on car floor of Rescreen building hurting lower back and right hip.

Employee was checking fuel level on engine, placed hand on exhaust thinking it was the air box and burned palm of left hand.

EMPLOYEE SLIPPED ON ICY CATWALK BETWEEN SAND SCREWS, LACERATED RIGHT ELBOW, WENT TO E.R. AND RECEIVED 3 STITCHES.

EMPLOYEE OPERATING TRUCK, LOADER WAS LOADING STONE INTO THE TRUCK. AFTER LOADING LAST BUCKET HE BACKED AWAY & A STONE FELL FROM BUCKET, HITTING TRUCK MIRROR AND PROPELLING GLASS THROUGH THE TRUCKS OPEN WINDOW. EMPLOYEE HAD WINDOW OPEN - EYE STARTED HURTING 10 MINS AFTER INCIDENT.

EE WASA OPERATING HAUL TRUCK, WAS WEARING SEAT BELT, HE WAS LOADED WITH WASH POND SALT, LOAD WAS LOOSE AND SHIFTED TO BACK OF TRUCK BED CAUSING FRONT OF TRUCK TO COME OFF GROUND, WHEN LOAD RELEASED TRUCK'S FRONT END LANDED BACK ON THE GROUND.

EE HIT HIS THUMB WITH A HAMMER WHEN HE WAS CHANGING A FEED CHAIN LINK ON A BLAST HOLE DRILL.

EE WAS USING A 4" GRINDER TO GRIND OFF EXTRA BOLT LENGTH FOR BELT CLAMPS ON S2 CONVEYOR. WENT HOME FOR THE DAY, EYE WAS BOTHERING HIM. HE TRIED TO WAIT IT OUT, EYE GOT WORSE. WENT TO DOCTOR AN D THEY REMOVED MATERIAL FROM HIS LEFT EYE.

EE WAS DRILLING AND BLOWING COMPRESSED AIR WHEN HE FELT A DISCOMFORT IN HIS RIGHT EYE. THIS INJURY WAS NOT REPORTED TO US - WE RECEIVED BILL & RESEARCHED IT.

EMPLOYEE WAS STEPPING UP INTO HAUL TRUCK WHEN HIS FOOT SLIPPED UNDER THE RUNG WHILE HIS OTHER FOOT WAS ON THE RUNG. HE HAD HOLD OF THE LADDER AS HIS FEET SLID UNDER THE RUNG AND HE STRAINED HIS BACK.

EE WAS OPERATING LOADER--TRAVELING ACROSS SILICA BENCH WITH A BUCKET OF STONE AND RAN OVER A LARGE ROCK. THE QUICK SID TO SID AND BUMP STRAINED HIS RIGHT SHOULDER.

EE WOKE UP THE MORNING OF 1-21-02 WITH SEVERE BACK PAIN, HE THINKS IT WAS CAUSED FROM A JARRING THAT HAPPENED WHILE RUNNING JD LOADER THE PREVIOUS WEEK. NO SPECIFIC TIME OR DATE.

EE WAS SHOVELING SPILLAGE ONTO BELT, WHILE LIFT-ING AND TURNING HE FELT A SHARP PAIN IN HIS LOWER BACK.

EE WAS WALKING AWAY FROM SOME EQUIPMENT WHEN HIS FOOT SLIPPED ON FRESH SNOW. WHEN HIS FOOT KICKED TO THE SIDE HE SAID HIS KNEE DISLOCATED & POPPED BACK INTO POSITION. DOCTOR'S DIAGNOSIS: DISLO CATION OF PATELLA.

EE WAS WALKING UP A SET OF STAIRS AND TRIPPED ON THE STEP. THE STEPS WERE FREE OF ALL DEBRIS AND EE'S HANDS WERE EMPTY. EE ENDED UP BREAKING A TOOTH AND PUNTURING THE LIP.

EE WAS WALKING WHEN HIS HEAD HIT A BEAM, HE DUCKED BUT NOT ENOUGH. HE HIT HIS HEAD PRETTY HARD RESULTING IN PAIN IN NECK AND BACK. HE DIDN'T GO TO DR. UNTIL HIS FINGERS ON RIGHT HAND STARTED GOING NUMB.

EE WAS WAHING SPILLAGE OFF THE FLOOR WITH HIGH PRESSURE HOSE, EE TRIPPED OVER THE PART OF THE HOSE THAT WAS LAYING ON THE FLOOR, EE HURT LOWER BACK.

EE WAS IN HAUL TRUCK, WHILE HIS TRUCK WAS BEING LOADED THE LOADER BUCKET HOOKED THE SIDE OF THE TRUCK BOX. AS THE LOADER WAS BACKING AWAY THE BUCKET WHICH THEN RELEASED THE TRUCK WHICH SNAPPED BACK TO LEVEL POSITON, JOSTLING EE.

EE WAS INSPECTING D-7 CONVEYOR WHILE LEARNING OVER EE PUT HIS HAND ON A CHANNEL INT HE SINTER BUILDING, IN THE DUST ON THIS CHANNEL WAS A WELDING ROD THAT PIECED THE PALM OF HIS HAND LEFT ENTE RED BY MIDDLE FINGER EXITED BY INDEX FINGER.

EE WAS REMOVING DEBRIS FROM CEMENT BLOCK BUILDING & STRAINED HIS BACK.

OPERATING #37 LOADER REPAIRING ROADS WHEN HE TURNED TO LOOK BEHIND HIM TO BACK THE LOADER UP AND THEN HE HEARD HIS SHOULDER POP.

EE WAS WALKING TO CAT TRUCK WITH LUNCH PAIL WE WERE HAVING A BAD SNOW STEAM WHEN HE SLIPPED ON PACKED SNOW/ICE AND FELL ON LEFT SIDE.

EE WAS HANGING COME-ALONG AND STEPPED ON COUNTERWEIGHT WHICH HAD MUD ON IT. HIS FOOT SLIPPED OFF & HE LANDED ON HIS KNEE ON THE EDGE OF THE COUNTERWEIGHT.

EMPLOYEE WAS ROLLING A 55 GALLON DRUM OF OIL FROM FORK LIFT ONTO BED OF COMPANY TRUCK AND THEN NEXT DAY COMPLAINED OF SEVERE LOWER BACK PAIN.

UNLOADING A BARREL OF OIL FROM PORTABLE FORKLIFT ONTO PICKUP TRUCK BED, AND BARREL TIPPED AND HE ATTEMPTED TO CATCH IT, AND STRAINED HIS BACK.

LIFTING 50 LB BOXES ONTO SHELF AT SHOULDER HEIGHT, STRAINED SHOULDER.

PULLING PUMP OUT OF DRILLED BLAST HOLE, BECAUSE THE DEWATERING PUMP FAILED, STRAINED LEFT FOREARM.

EE WAS CRANKING UP A CHUTE ON DISCHARGE HOPPER AND HE JAMMED HIS HAND BETWEEN CRANK HANDLE AND FLOOR.

TWISTED BACK WHILE SHOVELING AND LIFTING MATERIAL (SPILLAGE) ONTO CONVEYOR BELT.

LOADER OPERATOR ACCIDENTALLY HIT THE QUICK RELEASE LEVER ON LOADER BUCKET. IT DESCENDED AND STRUCK SIDE OF HAUL TRUCK, JARRING THE OPERATOR.

EE WAS USING A HAND GRINDER ON HEAD PULLEY AND FOREIGN PARTICLE ENTERED HIS EYE.

EE WAS STOOPED OVER IN TIGHT CONDITIONS, CHANGING OIL FILTER IN A COLD ENVIRONMENT. STRAINED BACK.

REMOVING SIDE PANEL FROM LOADER-WHILE PULLING ONTHE COVER, HE STRAINED HIS MUSCLE

HE WAS LIFTING A CABLE FROM ONE SPILE TO PUT ON ANOTHER SPILE WHILE ASSISTING THE VESSEL AT THE DOCK AND HE STRAINED HIS BACK.

STRUCK ELBOW AGAINST SCREEN FRAME WHILE TRYING TO REMOVE A BROKEN BOLT. WELD LET GO CAUSING ARM TO STRIKE FRAME.

REMOVING ENGINE FROM HAUL TRUCK PULLING ON WRENCH TO LOOSEN A BOLT, STRAINED HIS WRIST

CLIMBING DOWN LADDER OF HAUL TRK, VERY ICY, LOSTGRIP & FELL 5FT TO PLATFORM, STRUCK HIS CHEST AGAINST RAILING

SHE WAS SHOVELING DIRT FROM UNDER A WATERLINE AND TWISTING/LIFTING MOTION CAUSED A MUSCLE STRAIN IN HER BACK.

HE WAS REMOVING AN ANGLE THAT HOLDS SCREENS DOWN AND WHILE GRINDING THE SURFACE A HOT SPARK FLEW INTO HIS EYE.

HE STEPPED OFF BOTTOM STEP OF STAIRS AND SLIPPED ON MUDDY SURFACE CAUSED BY RAIN.

CLIMBING LADDER TO GET IN CAB OF DOZER, FELT A KNOT IN HIS LEG, AS DAY WENT ON HIS FOOT BECAME NUMB.

CHANGING SCREENS IN THE RESCREEN BUILDING, PUSHING THE SCREEN CLOTH UP THE SCREEN DECK, FELT MUSCLE PULL IN ARM.

HE KNELT DOWN TO START WELDING SPEED BRACKET TO CONVEYOR ANBD HE KNELT ON A STONE CAUSING HIM TO REACT SUDDENLY TWISTING HIS BACK.

REPETETIVE CUMULATIVE TRAUMA. RIGHT SHOULDER FROM DAILY CHECKING BLAST HOLE DEPTHS, BY BOBBING A 100' WEIGHTED TAPE UP & DOWN IN THE BLAST HOLE. CAUSED SHOULDER SORENESS.

DRIVER NOTICED A SHARP PAIN IN HIS BACK DURING NORMAL HAUL TRUCK OPERATION.

HE WAS LIFTING A BOX OF BOLTS TO PLACE IN STORAGE RACK AND STRAINED HIS BACK.

EMPLOYEE WAS BACKING UP HAUL TRUCK FOR LOADING &HE BACKED INTO THE FACE WALL AND JOLTED THE TRUCK. LOADER OPERATOR SPOTTED HIM TOO CLOSE TOFACE WALL.

LIFTING FREIGHT ELEVATOR DOOR.

FELT SORENESS IN BACK AFTER MOVING POWER PANELS AT THE BOAT LOADER MOTOR CONTROLLER.

WALKING TO HIS TRUCK IN PARKING LOT TO GO HOME INTENDED TO STEP OVER SNOWDRIFT-HIT ICE PATCH & TWISTED HIS KNEE

EE WAS REMOVING WEAR PLATE FROM BY-PASS CAR AT THE RESCREEN-LATER IN LUNCH ROOM FELT PAIN IN BACK WHEN HE AVOISE FROM LUNCH TABLE.

EE WAS GETTING OUT OF HIS TRUCK IN PARKING LOT AND HE SLIPPED ON ICE AND FELL.

TIGHTENING BOLTS WHILE WORKING AT THE CRUSHER AND DIRT FLEW IN HIS EYE WHILE RUNNING AIR POWEREDGUN.

REPETIVE TRAUMA-DERMATITIS & CURLING OF FINGERS CAUSED BY SHOVELING

EE WAS WORKING ON EXTENSION LADDER. REMORTARING AND LADDER SLIPPED AND EE JUMPED OFF OF LADDER TO GROUND.

CLIMBING UP LADDER OF THE HAUL TRUCK-FELT SOMETHING POP IN HIS RIGHT LEG.

WORKER AND PARTNER WERE INSTLALING AN OVERHEAD PIPE, WORKER'S PARTNER DROPPED THE PIPE, IT STRUCK THE INIWED'S HARD HAT AND JAMMED HIS HAND INTO HIS SAFETY GLASSES. WHICH CUT HIS UPPER EYEBRO W.

EE WAS HANDING DOWN SHEET ENGINE COVER TO PACE ON WORK STAND. THE COVER FELL OFF THE STAND AND SNAGGED WORKER'S COVERALLS AND HE FELL TO THE FLOOR.

CLIOMBING ON A HAUL TRUCK WITH A GASKET SCRAPER IN POCKET, HAND SLIPPED AND STRUCK THE SCRAPER.

PULLING A STEERING WHEEL ON #13O PICKUP WHEN IT BROKE LOOSE HE FELL BACK STRIKING HEAD ON REAR WINDOW

PULLING 2ND PUSHING SCREEN CLOTH INTO PLACE WHILE DOING A SCREEN CHANGE.

OPERATING DRILL AND HE LOOKED OVER HIS SHOULDER THEN BACK FORWARD AND HAD SEVERE NECK PAIN.

HE WAS CLEANING DIRT BUILDUP FROM END OF B-2 BOOM AND WHILE CLIMBING OVER THE DRIVE MOTOR HE STRUCK HIS KNEE ON EDGE OF MOTOR

EMPLOYEE WAS SHOVELING SIRT AND MATERIAL ONTO BELT ADN TWISTING AROUND HE STRAINED HIS KNEE.

DRIVER WAS BEING LOADED AND LARGE ROCK DUMPED INTO BED JARRING THE HAUL TRUCK

EE WAS USING UTILITY KNIFE TO CUTTING RUBBER SKIRTING AND BLADE HIT TOP OF HAND

EE WAS WORKING ON TEMPORARY FLOOR PLACED OVER DISCHARGE HOPPER TO BOLT SCREEN IN PLACE AND THE FLOOR JOIST BROKE AND FLOORING GAVE WAY AND EE FEEL INTO DISCHARGE HOPPER AND BIN.

EE WAS ATTEMPTING TO OPEN DOOR OF LOADER-LATCH FAILED AND DOOR JERKED OPEN JARNING THE OPERATOR.

EE WAS ENTERING A SAMPLE STATION. DOOR WAS JAMMED SHUT BY DIRT. HE ATTEMPTED TO OPEN THE DOOR BY PULLING ON HANDLE DURING WHICH HE STRAINED HIS LEFT SHOULDER & NECK.

CLIMBING LADDER TO GET TO A SCAFFOLD TO WORK ON BEARING. STEPPING FROM LADDER TO SCAFFOLD HE SLIPPED & FELL ON ARM.

OPERATING DRILL PRESS. MOVING HOLDOWN TABLE TO INSERT HOLD DOWN BOLT - STRAINED RIGHT SHOULDER.

CLIMBING DOWN LOADER STEPS. SLIPPED ON LAST STEP ADN FELL STRIKING LEFT SHOUDLER AGAINST ENGINE CASING.

WINDOW SPRING BROKE ON DRIVERS SIDE WINDOW OF HAUL TRUCK AND PINCHED WORKERS FINGER BETWEEN WINDOW HANDLE AND DOOR FRAME.

CHANGING TOP DECK SCREEN. STEPPED OFF SCREEN ONTO WORK PLATFORM THAT HAD STONE SPILL ON IT. HE STEPPED ON LARGE STONE AND TWISTED HIS RIGHT KNEE.

USING AN OVERHEAD CRANE TO LIFT AND PLACE IDLER ROLLER UNDER BULLDOZER. PUSHING AND LIFTING CAUSED BACK STRAIN.

OPERATED DOZER IN WASH POND FOR FULL EIGHT HOUR SHIFT OVER ROUGH OEPRATING OCNDITIONS. LOWER BACK FATIGUE.

USING HAMMER TO DRIVE OUT BROKEN BOLT. HAMMER GLANCED AND STRUCK FACE.

INJURED WAS DRIVING CAT HAUL TRUCK BACKING UNDER LOADER. LOADER OPERATOR ACCIDENTALLY MOVED HOIST LEVEL INTO FREE FALL MODE AND DROPPED THE BOOM WITH A FULL BUCKET ONTO THE SIDE OF HAUL TRUCK, THE IMPACT JARRED THE OPERATOR OF TRUCK QUITE SEVERLY WITH A WHIPPLASH EFFECT.

REPAIRING HOIST CYLINDER. PUSHING CYLINDER HEAD ONROD AND HAND SLIPPED. STRUCK MACHINED EDGE. CUT WRIST.

CLEANING LOADER BUCK WITH SHOVEL 2ND EE STAINED HIS BACK.

OPERATOR WAS CLEANING DOZER TRACKS TRYING TO RMEOVE A BLOCK OF SHALE.

FREIGHT ELEVATOR DOORS JAMMED & EE BENT DOWN TO LIFT TOP SECTION OF DOOR-STRAINED HIS BACK.

EE WAS WORKING ON BERM BY STACKOS. IT WAS RAINING AND AS HE WENT TO ENTER THE BUILDING HE SLIPPED ON CATWALK WHICH WAS WET & FELL.

EE WAS WORKING ON DRILL TO FIX HYDRAULIC LEAK AND HE SLIPPED ON SLIPPERY DECK & STRUCK HIS HEAD.

EMP ENTERED CRUSHER FOR SETTING MEASUREMENT AND HE WAS HOLDING ONTO ENTRY DOOR AND SLIPPED ON LOOSE STONES STRAINING HIS NECK AND UPPER SHOULDER.

EE WAS OPERATING DOZER TO REMOVE FROZEN MATERIALAND MATERIAL BROKE LOOSE JARRING OPERATOR.

EMPLOYEE WAS WALKING ACROSS PARKING LOT TO START DOZER. WEATHER CONDITIONS WERE BLOWING SNOW (30 MPH WINDS). HE SLIPPED ON ICE AND HE FELL TO THE GROUND.

REPAIRING THE STEERING MECHANISM FOR LOADER AND DROPPED A WASHER. IT FELL BETWEEN FRAME AND CAB.CRAWLED UP TO RETRIEVE IT. LOST HIS FOOTING AND FELL AGAINST THE MACHINE FRAME.

EXCESSIVE GLARE COMPOUNDED EXPOSURE TO WELDING OPERATION WHILE PASSING THROUGH WELDING DEPARTMENT. OVERDOSE OF ULTRAVIOLET LIGHT - AFFECTED EYES.

HE WAS WORKING WITH A PARTNER INSTALLING A CHUTE LINER WEAR PLATE AND AS THEY WERE LIFTING THE WEAR PLATE INTO PLACE THE MAGNET WAS ACTIVATED AND PULLED THE WEAR PLATE TO THE MAGNET PINCHING I NJURED S HAND.

LOADER OEPRATOR WAS TRYING TO SET A LARGE STONE IN BED OF 85 TON HAUL TRUCK AND THE STONE DROPPED INTO BOX JARRING THE TRUCK OPERATOR.

EE WAS FUELING A PICKUP AND HE SLIPPE ON THE ICE AND ATTEMPTED TO STOP FALL BY TWISTING AROUND TO GRAB THE PICKUP AND HIS KNEE POPPED.

CLIMBING UP ONTO AN I-BEAM AND EMPLOYEE LOST HIS BALANCE AND CAUGHT HIMSELF, JARRING HIS BACK.

EE WAS WALKING OUT OF TUNNEL ON AN ALUMINUM WALKWAY WHEN HE SLIPPED ON ICE AND STEPPED OFF OF WALKWAY INTO HOLE.

WALKING UP OUTDOOR STAIRS TO THE WEIGHOUSE. SLIPPED AND FELL ON STAIRS THAT WERE ICY.

OPERATING 30 LOADER FELT SORENESS IN BACK WHILE DESCENDING LADDER AT THE END OF THE SHIFT.

WORKING IN BOILER ROOM REPLACING BACK ON BOILER. PLATE SLIPPED OFF HORSES PINCHING EE'S FINGER BETWEEN HORSE & BOILER BACK.

LIFTING DISCHARGE GATE AND GATE WAS FROZEN--STRAINING BACK.

EE WAS GRINDING A WEIGHT OFF WHEEL RIM AND PARTICLE FLEW INTO EYE. WORKER WAS WEARING SAFETY EYE PROTECTION.

CLIMBING OFF LAST STEP OF LOADER AND TWISTED ANKLE ON ROCKY MUDDY SURFACE.

WORKING ON CAT BOX HEATING AND USING SLEDGE HAMMER TO WELD IN PIECES BACK TIGHTENED UP AFTER SWING SLEDGE.

EE WENT OUTSIDE TO PUT WASTE MATERIAL IN DUMPSTER, AND WIND BLEW DIRT INTO FACE.

REPETIVE BENDING, TWISTING AND LIFTING AS A MECHANIC BROUGHT ON ONSET OF PAIN.

EE WAS GETTING OUT OF PICKUP & HE REACHED BACK INSIDE TRUCK TO RETREIVE RADIA & HIS FOOT SLIPPED OUT & HE STRAINED HIS BACK.

SHOVELING MUD FROM UNDER C-1 CONVEYOR, TWISITNG AND SHOVELING.

CLIMBING DOWN FROM GRADER & HIS PANT LEG HOOKED ON A CABLE HOOK & EE FELL STRIKING HIS RIGHT SHOULDER.

WALKING TO BREAK SHACK AND SLIPPED ON LOOSE ROCKS AND FELL TO THE GROUND.

EE WAS REMOVING BRAKE MOTOR FROM UNDER DRILL AND HE STOOD UP AND STRUCK HIS RIGHT SHOULDER ON DECKING OF DRILL.

EMPLOYEE WAS BENDING OVER SORTING WASHERS AND PLACING THEM IN A BIN AND FELT A SHARP PAIN IN LOWER BACK.

EE WAS USING CUTTING TORCHS TO REMOVE PIECE OF METAL AND HOT PIECE OF SLAG BURNED THRU HIS LEFT BOOT BURNING HIS FOOT.

EMPLOYEE WAS USING AIR GUN UNDER DOZER PUTTING COUNTER WEIGHT ON 2ND TWISTING MOTION CAUSED PAIN IN BACK.

WAS AT #12 DRILL USING A KNIFE TO CUT OFF DUST HOSE AND KNIFE SLIPPED OFF HOSE AND CUT HIS FINGERS.

EMPLOYEE WAS KNEELING ON FLOOR WHILE MAKING SCREEN CHANGE. HE TURNED TO GET A SIDE PLATE 2ND FELT HIS KNEE POP.

OPERATOR WAS CHECKING OIL AND COOLANT LEVELS ON #33 DOZER WHEN HE SLIPPED OFF TRACKS AND FELL AGAINST TRACKS. RAINY ICY CONDITIONS.

WALKING UP STAIRS BACKWARDS CARRYING D-1 SCALE AND INJURED TWISTED HIS BACK.

EMPLOYEE WAS DRIVING HAUL TRUCK. HE WAS BEING LOADED & A LARGE ROCK WAS DROPPED ONTO TRUCK JARRING OPERATOR.

INJURED WAS TRYING TO SLIDE UNDER DRIVE TUBE ON SCREEN AND HE REACHED UP AND GRABBED SCREEN FRAME TO PULL HIMSELF UP AND TWISTED LOWER BACK.

CLIMBING INTO SECONDARY CRUSHER TO REMOVE SPIDER BUSHING AND HE STRUCK HIS KNEE ON PIECE OF PROTRUDING STEEL.

SNATCH BLOCK LET LOOSE WHILE INJURED WAS USING A COME-A-LONG AND CAUSED THE HANDLE TO FLY AROUND STRIKING INJURED IN FOREHEAD.

DESCENDING STAIRS IN T-2 JUNCTION HE SLIPPED ON ICY SPOT ON FLOOR AND CAUSED STRAIN.

REMOVING SCRAPER AND PINCHED LITTLE FINGER BETWEEN PIPE AND CONVEYOR.

INSTALLING A REEL ON A CABLE WINDER - REMOVING PIPE COLLAR - COLLAR WAS STUCK - BROKE LOOSE, PINCHING EMPLOYEE'S THUMB.

ROLLING TIRE ON FLOOR. LOOSE WIRE STRAND ON SIDEWALL OF TIRE PUNCTURED EMPLOYEE'S FINGER.

HAULING TRAFFIC SIGNS TO PLACE ON QUARRY ROAD - UNLOADING FROM TRUCK WITH WINCH AND SIGN SLIPPED PINCHING HAND BETWEEN TWO SIGNS ON BACK OF TRUCK.

PULLING ON A PULLEY WITH A CHOKER & HIS BACK WENT OUT [CHANGING B-5 PULLEY]

EMPLOYEE WAS ASSISTING IN REMOVING A FEED CHUTE PLATE AND HE STRAINED HIS BACK BY TWISTING WITH HEAVY PLATE.

INSTLLING ASCRAPER AND WHILE CLIMBING IN CHUTE HIS FOOT SLIPPED ON STONES TWISTING KNEE.

CLIMBING OFF OF WELDING TRUCK EMPLOYEE TWISTED KNEE.

CONSTANT TURNING TO CHECK BEHIND LOADER - GRADUAL PAIN DEVELOPED- REPETITIVE TRAUMA INJURY.

MOVING AND EMPTYING WHEELBARROW FULL OF WASTE MATERIAL

EE WAS CHECKING UNDER CONVEYOR FOR MUD AND HE SLIPPED ON WET SURFACE AND FELL. HE GRABBED ANGLE IRON CORNER SUPPORT AND CUT HIS THUMB.

INJURED WAS CARRYING AN IDLE TO INSTALL AT NORTH END T-I CONVEROR & HE STEPPED ON A SOFT SPOT TWISTING KNEE.

DESCEDNING STAIRS 3 STACKER RAINY'S AND MUDDY OUT, WHEN SHE STEPPED DOWN SHE SLIPPED ON MUD AND FELL STRIKING COVEYOR SUPPORT.

EMPLOYEE WAS CLEANING MUD FROM SCREEN LIPS HE FLOPPED THE GATE OPEN & THE HANDLE BOUNCED BACK STRIKING HAND

WORK PARTNER HIT OUTER RACE OF BEARING ATTE MPTING TO REMOVE & THE BEARING SHATTERED & PIECE STRUCK INJURED IN THE SAFTEY GLASSES SHATTERING THE LENS

INJURED WAS GRINDING ON CAT TRUCK BOX TO PRONE FOR WELDING & PARTICLE GOT IN HIS EYE HE WAS WEARING SAFETY GLASSES WITH SIDE SHIELDS

INJURED WAS CLEANING DIRT BUILDUP FROM PAN UNDER CONVEYOR WITH A SCRAPER & HE HIT HIS FINGER ON PAN STRUCTURE

EMPLOYEE WAS ATTEMPTING TO CLIMB RAIL SYSTEM TO REPAIR HYDRAULIC PUMP ON TUNNEL CAR HIS FOOT SLIPPED OFF OF THE RAIL & HE HIT HIS SHIN ON THE RAIL

INJURED WAS LIFTING A 130 LB. PART FROM A WOODEN BOX.

INJURED WAS REMOVING ENGINE ON CAT TRUCK & HE PULLED ON AIR HOSE & EXCESS SLACK CAUSED AIR GUN TO FELL STRIKING HAND

WELDIGN ASEAM ON A DISCHARGE CHUTE AND A HOT SPARK BOUNCED AND LANDED IN HIS RIGHT EAR.

EMPLOYEE WAS WALKING TO THE SERVICE BUILDIKNG AND SLIPPED ON ICE AND FELL TO GROUND.

INJURED WAS KNEELING IN AWKWARD POSITION TO BURN A PLATE TO REPLACE WORN LINER PLATE IN DISCHARGE CHUTE EXTENDED TIME SPENT IN THIS AWKWARD POSITION CAUSED MUSCLE STRAIN

EMPLOYEE WAS SETTING A 60" ROLL OF BELTING ON A BELT STAND. WHILE LIFTING A CHOCKER IN PLACE TO MAKE A LIFT HE FELT PAIN IN HIS LOWER BACK.

WORKING IN PRIMARY CRUSHER PUSHING OUT SPIDER BEARING EMPLOYEE WAS CRAWLING OUT OF SMALL ACCESS DOOR WHEN HE FELT PULLING BURNING SENSATION IN LOWER BACK & HIP

INJURED WAS CUT TING LINERS FOR DISCHARGE CHUTES & HE STRAINED HIS BACK WHILE MOVING LINERS FROM SCREEN CHUTES

EMPLOYEE'S CO-WORKER WERE FILLIGN A DRAIN PIPE TO BE BLOWN CLEAN. PIPE LOACTED IN SLOPING DITCH ROCN FOOTING. EMPLOYEE SLIPPE DON ROCKS AND ICE QND FELL AND STRUCK HIS HEAD.

EMPLOYEE WAS MOVING HEAVY METAL PIPE WHEN A FLANGE FELL & STRUCK HIS HAND.

EMPLOYEE WAS WEARING COVERALLS & STEPPED ON LONG LEG, TRIPPING & FELL. AS FALLING SHE TRIED TO CATCH FALL WITH HANDS.

WASHING DOWN BOAT LOAD WITH A HIGH PRESSURE HOSE. STRAINED BACK WHILE PULLING ON HOSE.

CARRYING FUELING HOSE AT FAST FUEL STATION & HE SLIPPED ON FUEL OIL SPILL & FELL HE TRIED BREAKING HIS FALL CATCHING HIS RT HAND

EMPLOYEE WAS CARRYING 7 GALLON WASH BUCKET WHILE EXITING CONTROL ROOM. HE STEPPED DOWN FROM DOORWAY & FELL FORWARD STRAINING GROIN.

EMPLOYEE WAS CHECKING LIMIT SWITCH THAT CONTROLLED ROD RACK MOTION. ROD RACK WAS NOT SWINGING PROPERLY. HE MANUALLY DEPRESSED SWITCH AND ROD RACK DID NOT STOP AND HIS HAND WAS PINCHED BETWEE N BUMPER PLATE AND SWITCH CYLINDER ON #11 DRILL.

ELEVATOR STOPPED 3FT ABOVE THE FLOOR LEVEL 2ND DOORS WOULDNT OPEN EMPLOYEE WAS USING A 2X6 AS A LEVER TO PRY OPEN THE DOORS HE WAS PRYING OVER HIS HEAD & STRAINED HIS SHOULDERS & NECK

EMPLOYEE HAD SCREEN SECTION ON WORK HORSES TO BE WELDED. AS HE TRIED TO MOVE THE SCREEN HE TRIPPED ON WELDER CABLE AND TWISTED HIS BACK.

EMPLOYEE WAS MOVING A LARGE ROCK OUT OF TRUCK STALL AT PRIMARY CRUSHER - LIFTING.

EMPLOYEE WAS AIR-ARCING IN AN ENCLOSED AREA AND WELDING/CUTTING FUNE IRRITATED A PRE-EXISTING PNENMONIA CONDITION.

EMPLOYEE ASSISTING WELDER - USING JACK TO HOLD BRACKET IN PLACE TO BE WELDED. LOWERING JACK TO REPOSITION PIECE TO BE WELDED & PIECE FELL OFF OF JACK & PINCHED HER FINGER.

EMPLOYEE WAS WORKING TO INSTALL CYLINDER ON CHUTE IN CONVEYOR TUNNEL. HE WAS STANDING ON CONVEYOR SUPPORTS. HE SLIPPED OFF CONVEYOR AND WHEN HE LANDED ON FLOOR HE LANDED ON A ROCK AND TURNED H IS ANKLE.