Bessie Mine Coal

ROCK FALL IMEED INBY OPENING TO SURFACE IN 1 2 AND 3 ENTRIES EXTENTOF ROCK FALL NOT DETER UNTIL FURTHER WORK OT CLEAN FALL IS COMPL.

A ROOF FALL OCCURRED ON 4 SEC 5 ENTRY CROSSCUT TO THE RIGHT THE FALL MEASURED 25-30'X18'X5' HIGH THE STRATA CONSISTED OF LAMINATED SANDY SHALE

A ROOF FALL OCCURRED ON #4 SECTION #6 ENTRY ABOUT 160' OUTBY THE FACE THE FALL MEASURED 25'X19' X5' HIGH THE STRAT CONSTED OF LAMINATED SANDY SHALE

A ROOF FALL OCCURRED ON #4 SEC #3 ENTRY IN THE LAST OPEN X CUT ABOUT 50' OUTBY THE FACE THE FALL MEAASURED 24'X18'X5' HIGH THE STRATA CONSIST OF LAMINATED SANDY SHALE

A ROOF FALL OCCURRED ON #4 SEC #4 ENTRY 80' INBY THE LAST OPEN CROSS CUT THE FALL MEASURED APPROX 18' X 12 X 5' HIGH THE STRATA CONSIST OF LAMINATED SANDY SHALE

EMPLOYEE WORKS AS A ROOF BOLTER. HE WAS WAITING FOR LOADING MACHINE TO BACK OUT OF AN ENTRY WHEN THE CUTTING MACHINE TRAMMED BY ENTRY. AS CUTTER PASSED THE DUAL WHEELS RAN OVER A ROCK. THE ROCK SHOT OUT FROM UNDER THE WHEELS AND STRUCK THE EMPLOYEE ON THE RIGHT LEG.

A ROOF FALL OCCURRED ON #4 SECTION #6 ENTRY 80' INBY SPAD 7689. THE FALL MEASURED 25' X 20' X 5'. THE ROOF STRATA CONSISTED OF LAMINATED SANDY SHALE. THE ROOF WAS SUPPORTED BY 5' CONVENTIONAL BOLTS.

EMP WORKS AS A SHUTTLE CAR OPER HE WA> CRRYING A 5 GALLON CAN OF OIL TO HIS MAHCINE TO FILL THE RESERVOIR HE PLACED THE CAN ON TOP OF THE MACHINE TO REMOVE THE RESERVOIR CAP THEN HE REACH ED FOR THE OI CAN AS IT CAME OFF THE MACHINE THE WEIGHT OF THE CAN JERKED THE EMP CAUING PAIN IN HIS BACK

EMPLOYEE WAS RIDING IN A MANTRIP JEEP.AS HE DISEMBARKED FROM THE JEEP,HE FELT A PAIN I HIS ABCK.

EMPL WORKS AS ROOF BOLTED. HE WAS MARKING TOP IN PREPARATION FOR BOLTING. BITS OF COAL FELL FROM TOP AS HE MARKED & SOME GOT IN HIS EYE.

EMPLOYEE WAS WORKING AS A SCOOP OPERATOR. HE WAS DELIVERING SUPPLIES TO THE BRATTICE CREW. HE DISMOUNTED FROM THE SCOOP AND WALKED OVER TO THE AREA WHERE THE BRATTICE CREW WAS WORKING. AS HE A RRIVED, ONE OF THE BRATTICE CREW REMOVED THE TOP BLOCK FROM A STACK. WHEN HE DID, THE REST OF THE STACK FELL AND ONE HIT THE SCOOP OPERATOR ON HIS FOOT.

ROOF FALL OCCURRED ON #5 SECTION #4 ENTRY INBY SPAD 7615. 200' FROM FACE. FALL MEASURED 40'X24'X5'. ROOF STRATA CONSISTED OF LAMINATED SANDY SHALE. ROOF WAS SUPPORTED BY JENMANN BOLTS 5' LONG.

EMPL WORKS AS BRATTICEMAN.

EMPL WAS LIFTING 50 LB CASE OF BLASTING POWDER WHEN HE FELT PULL IN HIS UPPER BACK.

EMPL WAS RIDING IN MANTRIP AT START OF SHIFT. BECAUSE OF TRACK BEING FLOODED ALL EMPL ON MANTRIP GOT OFF & WALKED BELTLINE TO SECTION FACE. AS EMPL WAS STEPPING DOWN FROM BELTLINE SHE TWIST ED HER KNEE.

EMPL WORKS AS SUPPLYMAN/JEEP. HE HAD LOADED DRIVE GEARCASE FOR UN-A-TRAC ONTO HIS JEEP TO TAKE UNDERGROUND. GEARVCASE WAS NOT PROPERLY SECURED & FELL FROM JEEP. EMPL STRAINED HIS BACK P UTTING GEARCASE BACK ON JEEP.

EMPLOYEE WAS WORKING AS ROOF BOLTER AS HE WAS INSTALLING A COLLAR PIN STUCK IN HOLE THIS CAUSED PIN TO BEND & IN TURN KICKED OUT COLLAR WHICH STRUCK EMPLOYE E OVER THE EYE HIS EYE WAS CUT THIS REQUIRED SUTURES TO CLOSE

EMPLOYEE WAS REPLACING WORN BITS IN A CUTTER HEAD AS HE WAS APPLYING PRESSURE TO BIT LUG WITH WRENCH THE WRENCH SLIPPED THE EMPLOYEE LOST HIS BALANCE AND BUMPED HIS HEAD ON A CUTTER BIT CAUSIN G A LACERATION TO HIS HEAD WHICH REQUIRED SUTURES TO CLOSE

A ROCK FALL OCCURRED ON #5 SECTION IN THE LAST OPEN X-CUT OF #5 ENTRY.THE ROCK FALL WAS APPROXIMATELY 30'X18'X5' HIGH.THE ROOF CONSISTS OF LAMINATED SANDY SHALE.80'INBY SPAD #7626.

EMPLOYEE WORKS AS BELT REPAIRMAN. A CONVEYOR BELT HAD BECOME WRAPPED AROUND DRIVE ROLLERS IN A HEADER AS EMPLOYEE WAS ATTEMPTING TO CUT BELT, THE KNIFE HE WAS USING SLIPPED AND CUT HIS THIGH. SUTURES WERE REQUIRED TO CLOSE THE WOUND.

EMPLOYEE WAS REMOVING A MOTOR WHEN THE MOTOR SLIPPED AND CAUGHT HIS FINGER BETWEEN THE MOTOR AND THE PUMP FRAME,CAUSING A LACERATION WHICH REQYUIRED SUTURES TO CLOSE.

EMP. WAS OPERATING A SHUTTLE CAR. HE STOPPED TO REOVE ATRAILING CABLE THAT WAS BLOCKING HIS WAY. AS HE WAS LIFTING THE CABLE,, SOMEONE ENERGIZED THE TAKE-UP REEL ON THE MACHINE . THE SUDD EN MOVEMENT FO THE CABLE CAUSED THE EMP. TO LOSE HIS BALANCE, AND HE FEL AGAINS THE SHUTTLE CAR DECK HE STRUCK A GREASE FITTING WITH HIS FIGHT ARM, CAUSING A LACERATION TO T HE INSIDE OF HIS

EMPL ENTERED MACHINE CAB,SLIPPED & FELL INJURING WRIST.SENT TO DR,TREATED & RELEASED FOR WORK NEXT SHIFT.IN SEPT REQUESTED TO BE SENT TO DR -WRIST STILL HURTING HIM.10-17-NT TO DR,TREATED & RE 88 EXAMINED BY DR DIAG PROBLEM TO INJURY.1ST DAY OF DISABILITY 10-17-88.

A ROCK FALL OCCURRED ON 5 SECTION IN THE LAST OPEN X CUT OF 7 ENTRY THE FALL OCCURRED IN THE FACE AREA THE FALL MEASURED 20 FT X 30 FT X 7 FT HIGH THE ROOF CONSISTS OF LIMINATED SANDY SLATE 3 -CUTS INBY SPAD 7546.

A ROCK FALL OCCURRED ON 5 SECTION IN THE LAST OPEN X-CUT OF 5 ENTRY ABOUT 80 FT FROM THE FACE AREA. THE ROCK FALL WAS APPROX. 20X20X5 FT HIGH THE ROOF CONSISTS OF LAMINATED SANDY SLATE. 280 FT INBY SPAD 7544.

A ROOF FALL OCCURRED ON #4 SEC ABOUT 500' FROM THE FAC E AREA. THE FALL WAS ABOUT 20 X 20 X 4-6' HIGH. THE ROOF CONSIST OF LAMINATED SANDY SHALE. AT SPADD 7493 1 X CUT INBY.

EMPL WORKS AS LOADER HELPER. AS LOADER WAS TRAMMING FROM ONE PLACE TO ANOTHER, EMPL WAS MOVING CABLE. HE FELT PAIN IN HIS BACK AS HE PULLED ON TRAILING CABLE.

EMPLOYEE WORKS AS MOTORMAN HE ADD ANOTHER EMPLOYEE WERE REMOVING A PERSONNEL JEEP FROM THE TRACK THE OTHER EMPLOYEE WAS SIGNALING TO THE OPERTOR TO MOVE FORWARD WHEN THE SCOOP BUCKET CAUGHT T HE INJUREDS FOOT BETWEEN THE BLADE AND THE TRACK

THIS ROOF FALL WAS IN THE ARCH OF A PREVIOUS ROOF FALL THE FIRST FALL WAS REBOLTED WITH 3 FT CONVENTIONAL ROOF BOLTS THE ROOF CONSISTS OF LAMINATED SANDY SHALE

SHUTTLE CAR THIS EMPLOYEE WAS OPERATING HIT A HOLE IN THE ROADWAY. HE FELT PAIN IN HIS BACK BUT DID NOT GO TO THE DOCTOR. DOCTOR GAVE HIM PRESCRIPTION MEDICATION AND RETURNED HIM TO WORK.

INJURED EMPLOYEE IS A SUPERVISOR WHO WAS ASSISTING AN ELECTRICIAN SPLICE A SHUTTLE CAR CABLE.AS ELECTRICIAN WAS CUTTING CABLE COVER,HIS KNIFE SLIPPED AND CURT FOREMAN'S THUMB.A 2 CM LACERATION RESULTED AND SUTURES WERE REQUIRED TO CLOSE WOUND.

EMPLOYEE WAS ASSISTING ELECTRICIAN REPLACE COVER OVER CONVEYOR CHAIN ON FEEDER WHEN THEY HAD FINISHED & WERE CLIMBING OFF FEEDER EMPLOYEE CAUGHT LEG BETWEEN CONVEYOR CHAIN TAIL SPROCKET & REAR BUMPER TWISTING KNEE AS HE STEPPED DOWN

EMPLOYEE WAS INJURED ASSISTING ANOTHER EMPLOYEE IN REMOVING A RAIL FROG FROM A JEEP WHEN HE WAS INJURED. HE UNDERWENT SURGERY FOR A BILATERAL INGUINAL HERNIA REPAIR. RETURNED TO WORK 3-16-87 . HOWEVER, HE HAS HAD PAIN IN HIS GROIN RELATED TOSURGERY WHILE CONTINUING WORK.

EMPLOYEE WAS WALKING ALONG FOOTWALL SLIPPED AND FELL IN MUDDY AREA

PNEUMOCONIOSIS

EMPLOYEE WAS INITIALLY HURT ON 8-5-88 LOSING TIME A TOTAL OF 4 DAYS. THIS WAS DULY REPORTED. EMPLOYEE CONTIUNED TO WORK WITH PAIN AND DISCOMFORT ALTHOUGH NO ACCIDENT COMPOUNDED HIS PROBLEMS. UNTIL 3-14-88 WHEN HE WAS TAKEN OFF WORK BY DOCTOR.

ABOUT 40FT OF THE ROOF APPROX.8FT WIDE HAD BEEN SHOT OUT 5FT DEEP 5FT ROOF BOLTS WERE USED #5 SECT.#4 ENTRY FALL MEA SURED 82FTLONG 24FTWIDE APPROX.6FTHIGH LAMANATED SANDY SHALE SPAD 7418

ROCKFALL OCCURRED SECT#2 IN INTERSECTION 160'IBY/// INBY SPAD 7256 IN #5 ENTRY AND 240'OUTBY FACE.AREA 20' X 30' X 6'HIGH.INITIALLY SUPPORTED WITH 5' DOME NUT BOLTS.

ROCKFALL OCCURRED #5 SECTION #5 ENTRY 50'OUTBY X-CUTG FACE LEFT IN INTERSECTION.70'INBY SPAD 7457.FALL 25' X 65' X 6'HIGH.ABD WAS INITIALLY SUPPORTED WITH 5'CONV PINS.

AN ABANDONED SUR NITED METHANE RELEADED FROM THE SEALED SHAFT WITHIN THE BUILDING.TWO OF THE THREE NON-EMPLOYEE WERE INJURED,BUT AT THIS TIME THE EXTENT OF THEIR INJURIES ARE UNKNOWN,THIS INCIDENT WAS ORIGINAL

AN ABANDONED SURFACE STRUCTURE AT COAL CREEK SHAFT OF THE SEALED OFF OLD BESSIE MINE IGNITED AND EXPLODED.THREE MEN TRESPASSED IN THE AREA ENTERED THE BUILDING AND WHILE SMOKING APPARENTLY IGN ITED METHANE RELEASED FROM THE SEALED SHAFT WITH THE BUILDING.TWO OF THE THREE NON-EMPLOYEES TREPASSERS WERE INJURED,BUT AT THIS TIME THE EXTENT OF THEIR INJURIES ARE UNKNOWN.THIS INCIDENT OR

AN ABANDONED SURFACE STRUCTURE AT COAL CREEK SHAFT OF THE SEALED OFF OLD BESSIE MINE IGNITED AND EXPLODED.THREE MEN TRESPASSED IN THE AREA ENTERED THE BUILDING AND WHILE SMOKING APPARENTLY IGN ITED METHANE RELEASED FROM THE SEALED SHAFT WITHIN THE BUILDING.2 OF THE 3 NON-EMPLOYED TRESPASSERS WERE INJURED,BUT AT THIS TIME THE EXTENT OF THEIR INJURIES ARE UNKNOWN.

EMPLOYEE WAS A PASSENGER IN A MANTRIP JEEP THAT WAS LEAVING MINE AS JEEP WAS GOING DOWN A DECLINE & REACHED BOTTOM JEEP BOTTOMED OUT HARD CAUSING EMPLOYEE PAIN IN HIS BACK EMPLOYEE DECLINED TO SEE DOC.AT TIME OF ACCIDENT SUBSEQUENTLY WENT ON OWN T O CHIROPRACTOR REQUESTED DOC.APPOINTMENT & WENT ON MARCH 30 1988

EMPL STANDING BESIDE CUTTING MACHINE WHEN CUTTER WHEEL THREW UP A ROCK WHICH HIT EMPL ON ANKLE.

A ROCK FALL OCC6RRED ON THE #5 SECTION IN THE #5 ENTRY.A CONTINUATION OF AN OLD FALL OF 02/04/87 IN AN INTERSECTION AT SPAD #6669.THE NEW FALL FELL FROM THE OUTBY BROW OF THE OLD FALL MEASURIN G 40 FT.X17 FT.3X5 1/2FT.

EMPLOYEE WAS INSTALLING CABLE ON COAL DRILL AS HE WAS CUTTING CABLE COVER HE CUT HIS FINGER THE WOUND REQUIRED SUTURES

A ROCK FALL OCC6RRED AT THE IONTERSECTION OF #31 BELT HEADER AND #21 BELT LINE WHICH WAS A CONTINUATION OF AN EARLIER FALL OF 0/02/87.THEFACE WAS OF THE OUTBY BROW AT INTERSECTION SPAD#6898 AN D MEASURED 30 0T. X11 FTX 8 FT. THE ROOF WAS SUPPORTED WITH 5 FOOT CONVENTIONAL ROOF BOLTS.

ROCKFALL OCCURR9D SECT #6 #3 ENTRY.DISCOVERED ON 1118?. 35' X 28'X 5' LOCATED IN INTERSECTION 65'OUTBY SPAD #7377. AREA SUPPORTED ON 5' CENTERS WITH 5' JENMAR BOLTS WI7H T-BOARDS.ALSO 5-6' DOME NUT BOLTS WERE SPOTTED IN INTERSECTION .

ON AUG. 10,19872 THE EMPLOYEE INJURED HIS KNEE AT THE WORKPLACE. HE WAS TAKEN OFF WORK BY THE DOCTOR, TREATED, AND RELEASED TO RETURN TO WORK ON AUG. 24,1987. HE HAD 9 LOST WORK DAYS. ON SUBSE QUENT OCCASIONS3HE WAS SEEN BY THE DOCTOR, COMPLAINING OF PAIN IN THE KNEE. NO LOST WORK DAYS WERE INVOLVED. WHEN THE KNEE FAILED TO RESPOND AS HOPED TO TREATMENT, THE DECISION WAS MADE TO PE

A ROCKFALL OCCU9RED ON THE SEC #6 IN THE #5 ENTRY 80 FT INBY SPAD #7309-30FT OUTBY THE FACE. THE AREA MEASURED 95'X15'X8' AND FELL DUE TO A VELTICAL SLIP RUNNING DOWN THE RT. R.B. THE AREA WA S SUPPORTED WIT2 5 FT JENMAR BOLTS.

EMPLOYEE WAS IN8TALLING RIB PINS IN RIGHT RIB OF #4 ENTRY WHEN THE RIB ROLLED AND A ROCK FROM THE RIB STRUCK THE EMPLOYEE'S FOOT. CAUSING INJURY.

A ROCKFALL OCCU9RED ON THE SEC #4 IN THE #2 ENTRY 50 FT INBY SPAD #7289 MEASUREING 90 FT X 20 FT X 5 FT THE AREA WAS SUPPORTED WITH 5 FT CONVENTIONAL PINS THE ROCKFALL OCCURRED BETWEEN 12-31- 87 AND 1-1-88 A7 9:15 PM THE TIME OF DISCOVERY

A ROCKFALL FELL3ON THE SEC. #6 IN THE #4 ENTRY IN AN INTERSECTION AT SPAD #7293 MEASURING 30'X30'X6-12'. THE ROCKFALL WAS DISCOVERED AT 10:35 AM AND THE LAST TIME ANYONE WAS ON THE SECTION #6 WAS 5:30 AM 3

A ROCKFALL OCCU9RED ON THE SEC.#6 IN THE #4 ENTRY & THE LAST OPEN XCUT INT ERSECTION THE AREA MEASURED 35FTX35FTX5FT & WAS LOCATED 50FT INBY SPAD #7293 THE AREA WAS SUPPORTED WITH SET.JENMAZ INSTALL III BOL7S

EMPLOYEE WAS MO5ING ROOF BOLTER TO THE LEFT SIDE OF THE PLACE HE WAS BOLTING, NEXT TO THE FOOTWALL. HE STEPPED ON A ROCK BESIDE THE FOOT WALL, THE ROCK ROLLED, AND THE EMPLOYEE FELL, TWISTING HIS ANKLE. 3

A ROCKFALL OCCU9RED IN THE SEC #2 80 FT INBY SPAD 7256 IN AN INTERSECTION MEASUREING 25X25X7. AREA WAS SUPPORTED WITH 6 FT DOME NUTS. AREA FELL SOMETIME BETWEEN 11 25 11 PM AND 11 28 3 AM. IT WAS DISCOVERED 6Y THE FIREBOSS

A ROOF FALL OCC6RRED ON #6 SECTION #4 ENTRY TWO CROSSCUTS INBY SPAD 7222, THE FALL MEASURED 24'X50'X6'. THE ROOF CONSIST OF UNCONSOLATED LAMANATED SANDY SHALE.

EMPLOYEE WAS WA5KING IN FACE AREA STEPPED ON ROCK AND TWISTED HIS ANKLE

ROOF FALL OCCUR9ED ON SEC.#6 IN INTERSECTION OF #5 ENTRY & LAST OPEN X-CUT 160FT INBY SPAD #7212ROCKFALL MEASURED APPROX.38FT LONG X18FT WIDE X6FT HIGH IN LAMINATED SHELL TOP AREA WAS SUPPORTE D WITH 6FT DOM9 NUTS

HE WAS DRILLING3HOLES FOR HANGERS WHEN SCALE FROM TOP FELL, STRIKING HIM ON HEAD, NECK, AND RIGHT SHOULDER

EMPLOYEE WAS IN3SUPPLY AREA ON SURFACE.HE WAS LOADING SAND BAGS ONTO SUPPLY CAR.AS HE WAS LIFTING A BAG,HE FELT A PAIN IN HIS LOWER BACK

A ROOF FALL OCC6RRED ON THE SEC#5 IN THE #7 ENTRY AND LAST OPEN X-CUT AT SPAD #7197 THE AREA WAS SUPPORTED WITH 8 FT DOME NUTS THE AREA OF THE FALL MEASURED 20 FT X 28 FT X 9 FT

INJURED WAS ATT9MPTING TO ALIGN BOLT HOLE FOR BUGDUSTER BOLT. EMPLOYEE PLACED SCREWDRIVER IN BOLT HOLE, WHEN THE BUGDUSTER MOTOR TURNED, CAUSING THE SCREWDRIVER TO SLIP, STRIKING EMPLOYEE ON H IS FINGER. THE 4ACHINE EMPLOYEE WAS REPAIRING WAS DE-ENERGIZED AT THE TIME OF INJURY.

AN IGNITION OCC6RRED ON THE #4 SECTION IN THE #7 ROOM FACE;WHILE THE CUTTING MACHINE WAS SUMPING UP,WEST OF SPAD 7117 INBY 214FT. THE FIRE WAS EXTINGUISHED WITH THE WATER DUMMIE GUN.THE FIRE L ASTED ABOUT 4 M3NUTES.

EMPLOYEE WAS HA3GING TRAILING CABLE OF MACHINE HE OPERATES ONTO OVERHEAD CABLE HANGER. AS HE LIFTED CABLE, HE FELT PAIN IN LOWER BACK.

EMPLOYEE WAS WO9KING AS CURTAIN MAN HE WAS STGANDING ON LADDER SECURING CURTAIN WHEN LADDER SLIPPED OR TIPPED FORWARD CAUSING EMPLOYEE TO FALL FROM LADDER

EMPLOYEE WAS LO5DING POWDER FROM POWDER CAR INTO POWDER BOX ON SCOOP.AFTER FINISHING,AS HE WAS EXITING POWDER CAR,EMPLOYEE STEPPED INTO HOLE IN FOOT WALL,TWISTING HIS LEFT FOOT.

EMPLOYEE WAS PU5LING DOWN PLASTIC CURTAIN PRIOR TO INSTALLING PERMANENT BRATTICE AS HE PULLED CURTAIN HE EXPERIENCED PAIN IN LOWER BACK

A ROCKFALL OCCU9RED ON SECT.#6 IN #4 ENTRY IN AN INTERSECTION AT SPAD#6921 ROCKFALL MEASURED 35FTX48FTX6FT IN HEIGHT FALLING ON SECTION BELT AREA WAS SUPPORTED WITH 6FT DOME NUTS

ROCK FALL OCCUR9ED ON #5 SECTION #6 ENTRY 40'INBY SPAD 7179 LOCATED IN #5 ENTRY.FALL WAS 22 X 30 X 9 HIGH.TOP IS LAMINATED SAND Y SHALE.

ROCKFALL OCCURR9D ON A#5 SEC.IN A#5 ENTRY LAST OPENX-CUT AT SPAD #7179 AREA OF ROCKFALL OCCURRED IN LAMENATED SHALE ZONE MEASURED 20FTX35FTX9FT IN HEIGHT

EMPLOYEE WAS LI0TING 6X8 COLLAR & STRAINED BACK

EMPLOYEE WORKS 5S SURFACE TRUCK MECHANIC AS EMPLOYEE WAS REMOVING WATER PUMP FROM DIESEL TRUCK HE LEANED OVER TO LIFT PUMP WHEN HE LIFTED HE EXPERIENCED PAIN IN HIS LOWER BACK

THE AREA WAS WI8E HOWEVER IT HAD BEEN REBOLTED WITH 8' DOME NUT BOLTS AND HAD BEEN NARROWED DOWN WITH CRIBS AND TIMBERS. THIS INTERSECTION WAS IN A SLIGHT TROUGH IN THE ELEVATIONS.THE MOST PRO BABLE CAUSE (CO3TRIBUTOR) WOULD BE THE 1-1 1/2" LAYER OF SANDSTONE AMID THE REST OF THE SHALE ROOF.THE SANDSTONE LAYER WAS RIGHT AT THE 8' TO 8 1/2' LEVEL.

EE WAS WALKING 8OWN INCLINE AREA OF THE MINE WHEN HE CAME TO A WET & SLIPPERY AREA OF FLOOR. AS HE WAS CROSSING THIS AREA HE LOST HIS FOOTING FALLING BACKWARDS & INJURING HIS BACK & RT HAND.

EMPLOLYEE WORKS3AS INSIDE ELECTRICIAN HE HAD COMPLETED REPLACEMENT OF SHUTTLE CAR CONVEYOR FLIGHTS & HAD ONE LEFT OVER AT COMPLETION OF WORK THE SPARE FLIGHT WAS LEANING ENDWISEAGAINST SHUTT LE CAR FELL OVE9 & STRUCK EMPLOYEES LEFT FOOT CAUSING POSSIBLE FRACTURE OF FOOT

EMPLOYEE STATES3THAT WHILE HE WAS WORKING ON A BRATTICE A BAT FLEW INTO HIS WORK AREA EMPLOYEE WAS ALARMED BY THE BAT AND CUT HIS LIGHT OUT AS HE MOVED OUT OF THE AREA STILL WITH LIGHT OUT HE TRIPPED AND FE5L INJURING HIS WRIST

EMPL WORKS AS B9ATTICEMAN.CUTTING BAND SECURING BLOCKS TO PALLET BAND SNAPPED BACK AND STRUCK HIM ON UPPER LEFT ARM.

EMPLOYEE WORKS 5S SUPPLYMAN ,JEEP HE WAS TRAVELING FROM UNDERGROUND TO SURFACE SUPPLY HOUSE TO PICK UP REPAIR PART AS HE WAS TRAVELING THE TROLLEY POLE JUMPED OFF TROLLEY WIRE HE CAUGHT POLE W ITH HIS RT ARM 7HE WEIGHT OF THE POLE ON IMPACT CAUSED HIS RT SHOULDER TO BE DISLOCATED

EMPL ENTERING M5NTRIP FOR START OF SHIFT.JEEP AHEAD OF MANTRIP BUMPED INTO EMPL SECTION JEEP STRIKING HIM ON LEG AND KNOCKING HIM TO GROUND.

THE AREA WAS IN3A LAMINATED ROOF ZONE.THE ROOF IN THIS AREA HAD TO SLIP AT 5' AND LONGER SUPPLEMENTARY BOLTS WERE INSTALLED.HOWEVER,THE ROOF CONTINUED TO DETERIATE.THE AREA WAS DANGERED OFF W HEN THE ROOF FA5L OCCURRED.DIMENSIONS: 22'X30'X8'.

EMPLOYEE WAS WO9KING AS CUTTING MACHINE HELPER. THE CUTTER WAS MOVING ACROSS THE FACE, AND THE EMPLOYEE WAS TAKING DOWN THE CABLE FROM HANGERS IN TOP. AS HE WAS REMOVING THE CABLE FROM THE H ANGERS, ONE HAN1ER CAME LOOSE FROM THE RIB, CAUSING THE CABLE TO FALL. EMPLOYEE REACHED TO CATCH THE CABLE AND THE HANGER HOOK PIERCED THE WEB BETWEEN HIS THUMB AND INDEX FINGER.

EE WAS WALKING 0ROM FACE TO FOOTWALL WHERE POWDER BOX WAS LOCATED. AS HE WAS WALKING HE STEPPED ON NAIL CAUSING PUNCTURE WOUND TO FOOT.

EMPLOYEE WAS RO7K DUSTER H ELPER WORKING AS BELTMAN CLEANER AS SHE WAS IN THE PROCESS OF CROSSING FROM ONE SIDE OF THE BELTLINE TO THE OTHER ANOTHER EMPLOYEE UNAWARE THAT SHE WAS CROSSING BELT STGARTED THE BE5T CAUSING INJURED EMPLOYEE TO LOSE HER FOOTING FALLING & STRIKING THE RETURN ROLLER AGAINSTG HER SELF-R ESCUER ON HER MINER BELT CAUSING BRUISE TO LOWER BACK

EMPLOYEE WAS WO9KING AS LOADER OPERATOR. SHUTTLE CAR BECAME HUNG ON RIB BEHIND LOADER. WHEN EMPLOYEE DISMOUNTED LOADER TO ASSES SITUATION, HE SLIPPED AND TWISTED KNEE.

THE FALL OCCURR9D ON THE TRACK ENTRY WITH 100 FOOT OF OVER BURDEN. THERE WERE AT LEAST 3 JOINTS IN THE MAIN ROOF WHICH WERE EXTENDED AFTER THE FALL. THESE JOINT COMBINED WITH WATER SEEPAGE F ROM SURFACE LED3TO A DETERIORATION OF THE ROOF AND EVENTUALLY THE ROOF FALL. THE FALL WAS APPROX. 900 FEET FROM THE PIT MOUTH.

A METHANE BLEED9R WAS LOCATED IN T HE RT CORNER OF THE CUT BEING MADE BY THE CUTTING MACHINE. ONE OF THE 2 WATER SPRAYS LOCATED ON T HE MACHINE MAY HAVE BEEN STOPPED UP.

EMPLOYEE WAS LI0TING BAG OF ROCK DUST AND PULLED MUSCLE-IN LUMBAR AREA OF BACK.

EMP WAS WORKING3AS LOADING MACHINE HELPER. AS HE LIFTED LID ON CABLE REEL TO CHECK ON TRAILING CABLE, THE LID SLIPPED FROM HIS HAND AND STRUCK HIM IN THE MOUTH CAUSING LACERATION TO UPPER LIP WHICH REQUI9ED STITCHES TO R EPAIR

LAMINATED SANDY3SHALE 24X24X6 INTERSECTION NO EQUIP DAMAGED

THIS SLABBING A9EA WAS IN A LOCATION OF THE MINE WHERE ROOF COAL WAS LEFT AS THE IMMEDIATE ROOF.WHEN THE SLABBING BEGAN.THE RESULTING STRESS LED TO A BREAK UP OF THE IMMEDIATES ROOF.EQUIPMENT LOST INCLUDED A3UNATRAK,ROOF BOLTING MACHINE ,FEEDER,POWER CENTER VACCUM BREAKER,SELF-CONTAINED SELF RESCUERS,AND A TOOL CAR.

EMP WAS ON LUN7H BREAK. HE HAD USED HISKNIFE TO CUT FRUIT AND THEN LAID IT DOWN, CUTTING EDGE UP. HE THEN LAY LEFT ARM ONTO SHARP EDGE

ROOF WAS BOLTED3WITH 5 FT CONVENTIONAL BOLTS, ROOF WAS LAMINATED, AND CROSSCUT ENTRIES DID NOT LINE UP, CREATING A LARGE INTERSECTION. ROOF FALL WAS 4FT THICK X 20 FT LONG X 24 WIDE.

..ROOF IN AREA 4ORKING BEGAN TO FALL.HE LIFTED MINER CABLE TO MOVE IT AWAY FROM ROCK FALL.AS HE LIFTED CABLE BEGAN TO HURT IN LEFT CHEST AREA.

THE AREA HAD AN3IMMEDIATE ROOF CONSISTING OF LAMINATED SHALE AND SANDSTONE.AREA WAS ROOFBOLTED WITH 5' CONVENTIONAL BOLTS.THE ROOF WAS APPROX.26' X 26' AND ABOUT 4' HIGH.THE ROOF FALL CAUSED N O DELAY IN PROD6CTION.

THE FALL OCCURR9D ON THE BELTLINE IN 4 ENTRY APPROX. 400 FTOUTBY THE LAST OPEN CROSSCUT. THE AREA WAS BOLTED WITH 5 FT CONVENTIONAL ROOF BOLTS THE ROOF CONSISTED OF SHALE WITH SOME LAMINATIONS 4.5FTX 28FT X 28 FT.

THE MAIN OR IMM9DICATE ROOF WAS MADE UP OF ROOF COAL. THE SECTION WAS ALSO SLABBING BETWEEN TWO PREVIOUSLY SLABBED AREAS. THE CONTINUOUS MINER WAS COVERED UP BUT WAS RECOVER AND SECTION WAS RE RETREATED AND 600 FT EXTENT OFR DAMAGE IS UNKNOWN.

EMPLOYEE WAS TA1PING THREADS ON BUGBUSTER WHEN TAP BROKE.HAND HIT JAGGED EDGE OF TAP CUTTING HAND.

EMPLOYEE AT TIM9 OF INJURY WAS WORKING AS BELT INSTGALLER AS HE WAS IN THE PROCESS OF JACKING UP BELT T HE JACK SLIPPED STRIKING EMPLOYEE ON THUMB HE REPORTED THE INJURY WAS SENT TO THE DOC. TREATED & RELEA8ED FOR WORK EMPLOYEE LOST NO TIME INITIALLY HOWEVER THE T HUMB CONTINUED TO BOTHER HIM HE WAS SENT BACK T O DOC.ON AUG 121987 TENDON DAMAGE WAS DIAGNOSED & EMPLOYEE TAKEN OFF W

THE AREA WAS IN3AN INTERSECTION APPROX 160 FT FROM THE FACE THE AREA WAS IN LAMINATED ROOF ON A SLIGHT ROLL IN THE FOOTWALL THE FALL AREA WAS BOLTED WITH 5 FT CONVENTIONAL ROOF BOLTS THE FALL WAS 60 FT LONG3X 26 FT WIDE X 5 FT HIGH FALL OXOCCURRED ON THE SECTION #6 BELTLINE

EMP WAS IN THE 1ROCESS OF PLACING CRIB BLOCKS UNDER A 14BU LOADER IN ORDER TO BE ABLE TO WORK ON THE UNDERCARRIAGE. WHEN HE MOVED ONE BLOCK TO PLACE IT UNDER MACHINE, HE STRUCK HIS R HAND AGA INST THE MACHIN9S HEAD MOTOR, CAUSING AN OPEN FRACTURE TO HIS RIGHT RING FINGER WITH RESULTING NEAR AMPUTATION OF FINGER

EMPL WORKING AS3ROOF BOLTER.AS HE WAS DRILLING HOLE FOR PIN,DRILL STEEL BROKE AND HIT HIM IN THE FACE.

THE AREA WAS IN3SLIGHTLY LAMINATED IMMEDIATE ROOF AND WAS ALSO IN THE BOTOM OF A TROUGH AREA,WHICH LED TO THE ROOFFALL.THE ROOF-FALL WAS APPROXIMATELY 35'LX35'WX5.5'H.THE FALL OCCURRED IN A FU TURE BELT ENTRY3AND WILL BE CLEANED UP.

EMPLOYEE WAS WO9KING AS ROOF BOLTER, ENGAGED IN CLEARING LOOSE SCALE PRIOR TO PINNING TOP. HE WAS USING ROCK BAR TO CLEAR OVERHEAD ROCK. AS HE WAS RAISING BAR TO MINE ROOF, HE FELT PAIN IN RIG HT SHOULDER. 3

FALL OCCURRED I3 A ROLL AREA AT THE LOWEST POINT ON THE SECTION. THE IMMEDIATE ROOF APPEARS TO BE LAMINATED SANDY SHALE. THE APPROX DEPTH OF THE OVERBURDEN WAS 800 FT. CON BOLTS INSTALLED IN THIS AREA WITH 7 BOARDS. HNO SPPLMENTAL ROOF SUPPORT HAD BEEN INSTALLED DIMENSIONS 20X22X5

EMPLOYEE WORKS 5S A BRATTICEMAN.HE WAS ENGAGED IN MOVING SACKS OF CEMENT TO AN AREA WHERE A BRATTICE WAS BEING ERECTED.AS HE WAS LIFTING SACK OF CEMENT,HE LOST HIS FOOTING AND FELL WITH THE SA CK ACROSS HIS S2OULDERS.

EMPLOYEE WAS OP9RATING ROOF BOLTER.HE WAS TIGHTENING BOLT WITH BOLT WRENCH IN AN AREA OF THE MINE WHERE THE ROOF IS 11' HIGH.UPON FINISHING BOLT TIGHTENING,EMPLOYEE LOWERED BOOM TO REMOVE WRE NCH ,WHEN WRENC2 HUNG ON THE PIN,THEN RELEASED,STRIKING BOOM HEAD AND THEN STRIKING EMPLOYEE IN THE FOREHEAD.

EMPLOYEE WAS CU7TING BELT SQUARE TO MAKE A SPLICE.THE KNIFE SLIPPED, CUTTING UPPER LEG.

EMPL OPERATING 9OOF BOLTER IN PROCESS OF INSTALLING ROOF BOLT AND TIGHTENING IT WITH WRENCH.AS BOOM WAS LOWERED TO INSTALL WRENCH THE WRENCH FELL STRIKING EMPL ON LOWER RIGHT LEG.

AS A GROUP OF E5ECTRICIANS ENTERED MINE TO BEGIN SHIFT THE MANTRIP JEEP THEY WERE RIDING DERAILED EMPLOYEES USED TWO JACKS TO RERAIL JEEP AS THEY WERE LOWERING JEEP ONTO RAIL T HE JEEP FELL FROM JACK CATCH3NG TO OF EMPLOYEES FOOT

EMPLOYEE WAS WA5KING BY FOOTWALL ENCOUNT ERED A SLIPPERY AREA LOST HIS FOOTING && FELL LACERATING RT LEG MEDICAL TREATMENT WAS REQUIRED INCLUDING SUTURES

EMPLOYEE DISCON3ECTED HYDRAULIC HOSE ON MACHINE HE WAS OPERATING HE FAILED TO RELIEVE PRESSURE ON H OSE BEFORE DISCONNECTING IT WHEN HOSE WAS DISCONNECTGED OIL SPRAYED INTO EMPLOYEES EYES PRES CRIPTION MEDICA7ION WAS ADMINISTERED BY DOC.IN ORDER TO PREVENT INFECTION

EMPLOYEE ASSIST9D MINE SAFETY INSPECTOR GET INJURED EMPLOYEE TO MANTRIP JEEP TORED EMPLOYEE TO MANTRIP JEEP TO TAKE OUT OF MINE.AS EMPLOYEE RETURNED TO WORK STATION.HE FELT PAIN IN HIS KNEE.D DOCTOR WHO EXAM3NED EMPLOYEE STATED EMPLOYEE STATES THAT THIS IS REOCCURRENCE OF INJURY SUSTAINED ON 11/03/86.AND WHICH WAS REPAIRED BY SURGERY.DOCUMENTATION FROM DOCTOR IS ON FILE AT MINE SIT

WHILE CHIPPING 2LD TILE OUT OF COAL CHUTE WITH AIR CHISEL, THE COUPLING IN THE AIR LINE BLEW OUT THE SEAL, LETTING AIR ESCAPE AND BLEW FRAGMENTS OF TILE OR METAL INTO EMPLOYEES EYE.

ROOF FALL WAS A1PROX 5' TO 5 1/2'H X 30'L X 25'W. THE ROOFFALL OCCURRED IN LAMINSTED ROOF CONDITIONS PRIMARY ROOF SUPPORT WAS 5' DOUBLE LOCK ROOF BOLTS

EMP WAS TRAMMIN1 CUTTING MACHINE INTO THE #3 ENTRY OF #5 SECTION WHEN MACHINE JUMPED OUT OF GEAR, CAUSING MACHINE TO SPEED UP AND COLLIDE WITH ENTRY FACE. THE FORCE OF THE IMPACT CAUSED HIM TO STRIKE HIS HEAD3AGAINST CANOPY POST ON MACHINE

LAMINATED ROOF 7ONDITIONS LEAD TO ROOF FALL. FALL WAS 5 1/2 FEET HIGH 24' WIDE AND APPROX. 25' LONG.

EMPLOYEE WORKS 5S INSIDE ELECTRICIAN. HE WAS GREASING A PIECE OF EQUIPMENT. WHILE LIFTING GREASE GUN, HE STRAINED HIS BACK. AT TIME OF ORIGINAL ACCIDENT, HE WAS TREATED BY DOCTOR AND RELEASED FOR WORK THE S5ME DAY. NO LOST TIME RESULTED. EMPLOYEE STATES THAT HIS BACK CONTINUED TO TROUBLE HIM, RESULTING IN HIS CONSULTING WITH DOCTOR AND BEING TAKEN OFF WORK BY DR. ON 7-20-87.

AN IGNITION OF 4ETHAD OCCURED ON THE 1 SECTION IN THE 3 FACE 125 FT INBY SPAD 6718. FACE WAS SHOT AND AS THE SHOOTER ENTERED THE 3 FACE TO REEXAMINE OF COAL THE AREA WAS WET DOWN AND EXTINQUIS ED WITH A WATER3HOSE AND WERE SAID THE BE EXTINQUISHED WITHIN 10 MIN.

EMPLOYEE WAS AS8ISTING ELECTRICIAN REPAIR BROKEN CONVEYOR CHAIN. THE EMPLOYEE WAS IN THE BED OF A SHUTTLE CAR. HE LOST HIS FOOTING SLIPPED AND FELL, CAUSING INJURY.

AN IGNITION OF 4ETHANE OCCURRED ON THE SEC 1 IN THE FACE X CUT LEFT THE 4 XCUT LEFT WAS SHOT AS THE SHOOTER RETURNED TO EXAMINE THE SHOT PLACE THE X CUT THE FACE WAS BURNING THE FLAMES WERE EX EXTINGQUISHED W3TH FIRE HOSE IN APPROX. 15 MIN THE XCUT WAS TURNED TO LEFT ABOUT 28 FT FROM A POINT 80 FT INBY SPAD 6740 THE FACE IN THE STRAIGHT WAS DRIVEN INBY THE X CUT 10 FT OR INBY SPAD

EMPLOYEE WAS A 1ASSENGER IN A MANTRIP JEEP EXITING THE MINE. AS THE JEEP PASSED UNDER A SHIELDING CANOPY, THE CANOPY COLLAPSED, CAUSING THE JEEP TO WRECK. THIS INJURY ACTUALLY OCCURRED ON 2-4 -87 AT 1:40PM. 3

EMPLOYEE WAS FU3CTIONING AS UN-A-TRAC OPERATOR. AS HE WAS GETTING OUT OF CANOPY OF MACHINE, HIS FEET SLIPPED ON MUDDY FLOOR OF MINE. HE FELL BACKWARDS ONTO FRAME OF MACHINE.

A ROCKFALL OCCU9RED ON THE #4 SECTION IN AN INTERSECTION OF THE #3 PLACE, 70 FEET WEST OF SPAD #6648. THE AREA OF THE ROCKFALL MEASURING 40 FEET LONG, 23 FEET WIDE, 10 FEET HEIGHT. THE AREA WAS SUPPORTED W3TH 8 FEET TAB NUT BOLTS WITH WOODEN COLLAZS.

THIS AREA IS IN3AN EXTREMELY LAMINATED IMMEDIATE ROOF AREA. THIS IS CONSIDERED TO BE THE PRIMARY CONTRIBUTOR TO THE ROOF FALL. THE FALL OCCURRED IN THE #3 FACE AND INTERESECTION. DIMENSIONS AR E 8'-10' HIGH, 30' LONG, 25' WIDE. PRIMARY SUPPORT WAS 8' TAB NUT BOLTS.

WHILE CROSSING 2VER BELTLINE ON CROSSALK, EMPLOYEE LOST HIS FOOTING AND FELL, TAKING WEIGHT OF FALL ON HIS LEFT HAND AND WRIST.

EMPLOYEE WAS WO9KING ON RIB BOLTING CREW. HE WAS HOLDING DRILL STEEL PRIOR TO BEGINNING DRILLING PROCEDURE. OPERATOR THOUGH HEHAD RELEASED THE STEEL AND STARTED DRILL, CAUSING EMPLOYEE TO WREN CH HIS WRIST. 3

LAMINATED ROOF 7ONDITIONS WERE THE PRIMARY CAUSE OF THE ROOFFALL ROOF FALL OCCURRED IN THE 5 FACE INTERSECTION. DIMENSIOUS 7 FT HIGH, 25FT WIDE AND 25 FT LONG.

EMP WAS MEMBER 2 FMINE SURVEY CREW WHICH WAS EXITING MINE AS MANTRIP JEEP PASSED UNDER SHIELDING CANOPY THE CANOPY FELL WRECKING JEEP

LAMINATED IMMED3ATE ROOF CONDITIONS LED OR WERE THE CONDITIONS WHICH LED TO T HE ROOF FALL. ROOF WAS IN T HE #6 FACE INTERSECTION. DIMENSIONS 5' HIGH 20' WIDE 25' LONG.

EMPL OPERATING 8HUTTLE CAR.AS MACHINE WAS TRAVELING DOWN RUNWAY,IT HIT A HOLE CAUSING INJURY TO BACK.

EMPLOYEE WAS WO9KING AS HELPER ON ROOF DRILL. AS HE WAS PUTTING A PIN IN A HOLE, A PIECE OF THE BROW FELL AND STRUCK HIM ON THE ARM.

EMPLOYEE WAS WO9KING AS ROOF BOLTER HELPER HE WAS INSERTING RESIN CARTRIDGE AND ROOF PIN INTO BOLT HOLE WHNE OPERATOR ACCIDENTLY ENERGIZED DRILL CAUSING EMPLOYEES HAND TO BE CAUGHT BETWEEN HO LE AND PIN CAUS3NG LACERATION

EMPLOYEE WAS WO9KING AS TRACKMAN HE & THREE OT HER EMPLOYEES WERE LIFTING TRACK RAIL TO PUT IT IN PLACE AS T HEY WERE LIFTING RIIL EMPLOYEE FELT BURNING SENSATION IN LOWER ABDOMEN

EMP WAS OPERATI3G UNATRAC UNLOAIDING SUPPLIES FROM SUPPLY CAR AS HE WAS REVERSING MACHINE, HE CAUGHT HIS ARM BETWEN SUPPLY CAR AND CANOPY POST ON UNATRAC

HIGHLY LAMINATE8 SHALE SANDSTONE IMMEDIATGE ROOF LITHOLOGY CONTRIBUTED TO ROOF FALL WHICH OCCURRED ON SECTION 4 IN 1 ENTRY FROM INTERSECTION TO FACE OF APPROX 60X9X20 NO PERSONNEL OR EQUIP WA INVOLVED 3

EMP WORKS AS RO2F BOLTER HIS MACHINE WAS DOWN BECAUSE OF A BLOWN HYDRALIC HOSE THE ELECTRICIAN WORKING ON IT HAD SET A ROF JACK UNDER THE BOM IN ORDER TO REPLACE HOSE WHEN REPAIRS WERE COMPLE THE ELECTRICIAN3RAISED THE BOOM WHEN HE DID THIS THE ROOF JACK FELL EMP TRIED TO CATCH THE JACK THE WEIGHT OF JACK HYPEREXTENDED HIS ELBOW

THE FALL OCCURR8 IN A LAMINATED IMMEDIATE ROOF REA. THE LIMINATED ROOF CONSISTS OF LAYERS OF SANDY SHALE. THIS WAS CONSIDERED TO BE THE PRIMARY CONTRIBUTING FACTOR LEADING TO THE ROOF FALL.

THE FALL OCCURR9D IN THE FACE INTERSECTION OF THE #3 PLACE OF SECTION #4 LAMINATED ROOF CONDITIONS ARE PREVALENT IN THE ROOFFALL AREA AND WERE CONSIDERED TO BE THE PRIMARY FACTOR LEADING TO T HE ROOF FALL TH9 DIMENSIONS WERE 25 FT X 40 FT X 7 FT HIGH

EMPLOYEE WAS WO9KING AS ROOF BOLTER WHILE DRILLING HOLE FOR ROOF PIN HE HAD HIS LEFT HAND RESTING ON THE BOLTER BOOM A PIECE OF COAL FELL FROM ROOF STRIKING HAND CAUSING FRACTURE INJURY TO IND EX FINGER 3

EMP WAS ENGERIZ3NG START BUTTON ON A D.C. AIR COMPRESSOR. THE SWITCH WHEN PRESSED SHORTED CAUSING BURN TO THUMB

A ROOF FALL OCC6RRED ON #3 SECTION RT SLOPE AT SPAD #6551

INJURED WAS ASS3STING ANOTHER EMPLOYEE SLIDING A RAIL FROG OFF A JEEP WHEN HE HURT HIS BACK.

THE FALL OCCURR9D INT HE FACE INTERSECTION OF THE #3 PLACE OF SECTION #5. LAMINATED ROOF CONDITIONS ARE PREVALENT IN THE FALL AREA & WERE CONSIDERED TO BE THE PRIMARY FACTOR LEADING TO THE ROOF FALL. THE3ROOF FALL DIMENSIONS ARE 25'X24'X8' HIGH.

EMPLOYEE STATED3A CONCRETE BLOCK POLLED OVER ON HIS RIGHT WRIST.

EMPLOYEE WAS PI3NING IN #3 ENTRY AND A PIECE OF SCALE FELL STRIKING HIM IN THE LEFT JAW AND ABOVE THE LEFT EYE.

EMPL WORKS AS R2OF BOLTER.AS HE WAS CLEANING LOOSE SCALE FROM AREA TO BE BOLTED,ROCK FELL FROM TOP HIT FOOTWALL AND TURNED OVER ONTO EMPL FOOT.

EMPL EMPLOYED A8 TRIP RIDER ON LOCOMOTIVE.AN UNMANNED JEEP HAD TROLLEY POLE SLIP OFF WIRE AND ROLL BACK AND BUMP INTO LOCOMOTIVE.IMPACT CAUSED JCT BOX ON LOCOMOTIVE MOTOR TO CAUSE LACERATION ON EMPL LEG. 3

LAMINATED SANDS7ONE ROOF CONDITIONS ENCOUNTERED IN AN INTERSECTION LEAD TO A ROOF FALL THE ROOFFALL WAS 8 FT HIGH 22 FT WIDE AND 25 FT LONG THE FALL IS CURRENTLY BEING CLEANED UP ON CYCLE

EMPLOYEE WAS DR3VING A SHUTTLE CAR THROUGH A CROSS-CUT WHEN A PIECE OF VENTILATION CURTAIN GOT INSIDE THE CAB.THE EMPLOYEE USED HIS ARM TO BRUSH THE CURTAIN OUT OF THE CAB.AS HIS ARM MOVED THE CURTIN OUTSIDE 2F THE CAB,THE CAR BRUSHED AGAINST THE RIB,SCRAPING HIS ARM AND CAUSING ABRASIONS AND LACERATION.

LAMINATED RROF 7ONDITIONS CONTRIBUTED TO THE ROOF FALL. THE FALL WAS APPROX. 20'X42'X5'. IT WILL BE DANGERED OFF AND NOT CLEANED UP. LOCATION WAS 100' INBY SPAD #6458.

EMPLOYEE WAS WO9KING AS UNDERGROUND ELECTRICIAN, ENGAGED IN REPLACING SHIMS IN A SHIM BOX ON FEEDER. HE WAS USING HAMMER TO DRIVE THE SHIMS INTO PLACE. HE HIT THUMB WITH HAMMER, CAUSING LACERA TION WHICH REQU3RED SUTURED TO CLOSE.

A ROCK FALL OCC6RRED ON #3 SECTION IN THE #4 ENTRY AT THE FACE. THE ROCK FALL WAS DISCOVERED ON AN IDLE SHIFT, NO EQUIPMENT WAS INVOLVED. THE ROCK FALL OCCURED IN THE FACE INTERSECTION AND MEA SURED 22' X 30'3LONG X5-6' HIGH.

EMPLOYEE WAS WO9KING AS A SHOOTER. HE WENT TO POWDER BOX TO REMOVE A CASE OF POWDER. HE BENT OVER TO PICK UP CASE AS H E LIFTED POWDER, HE FELT PAIN IN LOWER BACK.

EMPLOYEE WAS RI8ING MANTRIP JEEP INTO MINE WHEN JEEP REACHED WORK SITE EMPLOYEE DISEMBARKED FROM JEEP AS HE WAS EXITING JEEP HE STEPPED ONTO AN OBJECT WHICH ROLLED OUT FROM UNDERFOOT CAUSING H IM TO TWIST KNE9

ROOF FALL OCCUR9ED ON #3 SECTION IN #2 ENTRY,1 X-CUT DRIVEN EAST OFF OF #2 SOUTH MAIN ENTRY IN #2 FACE.ROCK FALL MEASURED 20' X 20' X 3' HIGH.ALL PROVISIONS OF ROOF CONTROL PLAN WAS FOUND TO B IN COMPLIANCE.3

5 BRATTICEMEN, 3NCLUDING THE INJURED EMPLOYEE, WERE TAKING DOWN A WOODEN DOOR. AT THE POINT THAT THE DOOR WAS LOOSE, THREE OF THE MEN LET GO OF THE DOOR, THROWING TOO MUCH WEIGHT ON THE OTHER TWO,CAUSING THE3RESULTANT BACK STRAIN TO THE INJURED.

EMPLOYEE WAS FI5LING CUTTING MACHINE WITH HYDRAULIC OIL FROM A 5 GALLON CAN WHEN HE FELT PAIN IN LOWER BACK

EMPLOYEE WORKS 5S A BRATTICEMAN HE WAS WALKING FROM AREA OF A REPAIRED CURTAIN THE AREA IN WHICH HE WAS WALKING WAS A STEEP HILLSIDE WITH A DROP OFF THE GROUND IN THE AREA WAS MUCKY AND SLICK AS THE EMPLOYE9 REACHED THE DROP OFF AREA HE LOST HIS FOOTING FELL ON HIS SELF RESCUER

EMPLOYEE WAS EN1AGED IN ATTEMPTING TO RE-RAIL A DERAILED MOTOR AND BRAKE CAR. WHILE LIFTING EQUIPMENT ONTO TRACK, HE FELT PAIN IN SHOULDER.

ON JLY 24 86 EM1 WAS CHANGING GEARS ON HEADER DRIVE AND APPARENTLY HURT BACK HE CALLED THE OWL SHIFT ELECTRICIAN FOREMAN AFTER RETURNING HOME SAYING HE NEEDED TO GO TO DOCTOR EMP WAS TREATED BY DR, RETURNED3TO WORK AND DID NOT LOSE TIME ON SEPT 30 86 EMP COMPALINED THAT HIS BACK WAS HURTING IN SAME AREA AND REQUIESTED TO GO TO DOCTOR

EMPLOYEE WAS WE5DING CHUTE AT RECEIVING FEEDER ON RUN-OF-MINE BELT. LEFT PANTS LEG CAUGHT FIRE FROM SPARKS AND BURNED LOWER LEG.

THE #2 SHUTTLE 7AR ON #3 SECTION HAD PULLED ITS POWER CABLE IN TWO. EMPLOYEE IS AN ELECTRICIAN, AND HE WENT TO THE POWER CENTER TO DE-ENERGIZE THE CABLE. AT THE POWER CENTER HE FOUND TWO PLUGS . ONE WAS TAGGE8 #3 S/C, THE OTHER HAD NO TAG. EMPLOYEE ASSUMED THAT THE PLUG WITH NO TAG WAS FOR THE DISABLED #2 S/C, AND LOCKED THIS PLUG OUT. HE DID NOT TEST TO SEE IF LOCKING OUT THE PLUG

INJURED EE WAS 5TTEMPTING TO CONNECT CHAIN ON F EEDER. WHILE USING A HAMMER TO PUT A SLAT ON CHAIN CONNECTING LINK EE STRUCK HAND WITH HAMMER.

A ROCKFALL OCCU9RED ON THE SECTION 4 IN AN INTERSECTION AT SPAD 6197 APPROX. 700 FT OUTBY THE FACE IN THE 4 ENTRY.

EMPLOYEE WASHEL1ING TO INSTALL OVERCAST. AFTER SHOOTING AREA WHERE OVERCAST WAS TO BE INSTALLED, HE WAS ROPING OFF AREA WHEN A PIECE OF ROOF SCALE FELL, STRIKING EMPLOYEE ON RIGHT SHOULDER, CA USING SEVERE BR6ISE.

EMPL LOADING AC9TYLENE CYLINDER BY HIMSELF.AS HE WAS LIFTING THE CYLINDER,HE FELT PAIN IN LOWER BACK.

EMP BENT OVER T2 PICK UP T-BOARD AND FELT PAIN IN LOWER BACK

WHILE PINNING A3 OVERCAST ON #2 SECTION EE WAS USING A 7' WRENCH TO TIGHTEN A ROOF BOLT. WRENCH SLIPPED FROM PINNER HEAD STRIKING EE ON FOOT.

EMP WAS PULLING3ON LOADER CABLE MOVING IT TO CLEAR ROADWAY WHEN HE LOST HIS FOOTING, SLIPPED UNDER STRAIN, STRAINED BACK

SMALL PIECE OF 8CALE ROCK FELL OUT OF TOP, HIT EMPLOYEE AND CAUSED LACERATION, REQUIRING SUTURES.

SUPEVISOR WAS T9OUBLE SHOOTING DEFECTIVE MOTOR MOTOR WAS GROUNDED RESULTING IN ELECTRICAL BURN

EMPLOYEE WAS WO9KING AS BRATTICEMAN. HE WAS ENGAGED IN CUTTING STRAPPNG BAND SECURING CONCRETE BLOCKS TO A PALLET. WHEN THE BANK WAS CUT, THE END CAME BACK, STRIKING EMPLOYEE AND CAUSING LACER TION. 3

ROOF FALL OCCUR9ED ON #7 SECTION IN #5 ENTRY,80'INBY SPAD #6103 IN INTERSECTION.INTERSECTION WAS 240'OUTBY FACE AREA INVOLVED MEASURED 20' X 22' X 5' HIGH.

A ROOF FALL OCC6RRED ON#4 SECTION IN #3 BELT ENTRY IN THE INTERSECTION OF THE LAST OPEN CROSS CUT AT SPAD #6194 IT MEASURED 5-6 FT HIGH X 22 FT LONG X 20 FT WIDE

EMPLOYEE WAS UN7OUPLING A MAHUAL COUPLING PIN PIN WAS STUCK & EMPLOYEE USED FORCE TO DISLODGE PIN WHEN PIN BECAME UNSTUCK EMPLOYEES THUMB STRUCK FRAME OF TRACK CAR CAUSING A 11/2 CM LACERATION TO THUMB STITCH9S REQUIRED TO CLOSE WOUND

A ROOF FALL OCC6RRED AT #6 SECTION-#4 ROOM, 80' INBY SPAD #6012. THE ROOF IN THIS AREA IS LAMINATED SANDY SHALE.

EMP HAD CUT POW9R OFF BELT LINE AND CROSSED TO OTHER SIDE AS HE STEPPED OFF BELT LINE HIS ANKLE ROLLED CAUSING SPRAIN

EMPLOYEE WAS CH5NGING OUT HYDRAULIC PUMP. THE OLD PUMP, BEING OILY, SLIPPED FROM EMPLOYEE S GRASP AND CAUGHT FINGER BETWEEN PUMP AND T BOARD.

EMPLOYEE WAS PL5CING PORTABLE ROOF JACK ONTO ROOF BOLTER. JACK SLID OFF BOLTER ONTO FOOT.

WHILE CLOSING K3IFE BLADE FINGER CAME IN CONTACT WITH BLADE RESULTING CUT REQUIRED SUTURES TO CLOSE

EMPLOYEE WAS CA9RYING A CASE OF POWDER. STEPPED INTO A SLIPPERY SPOT, SLIPPED, AND TWISTED KNEE.

EMPLOYEE WAS WO9KING AS LOADER HELPER. LOADER WAS MOVING INTO A NEW PLACE TO WORK AND EMPLOYEE WAS ENGAGED N MOVING TRAILING CABLE. IN THE PROCESS OF MOVING CABLE, EMPLOYEE STRAINED HER BACK.

WHILE PICKING U1 LOOSE CONCRETE BLOCKS, A BLOCK ROLLED OVER, CATCHING EMPLOYEEHS FINGER AGAINST ANOTHER BLOCK.

WHILE WALKING A9OUND 2 IN YELLOW MINE PIPE EMPLOYEE SLIPPED AND FELL

EMP ALONG WITH 4 OTHER MEN WAS PULLING FEEDER CABLE HE STATED HE FELT PAIN IN HIS BACK

AN INTERSECTION3FELL ON #1 SECTION IN #3 ENTRY 160 FEET INBY OR WEST OF SPAD #6059 FALL WAS DISCOVERED BY THE EVENING SHIFT UPON THEIR ARRIVAL ON THE FACES THE AREA MEASURED 20FTX20FTX4FT IN T HICKNESS 3

WORKINGS AS ISL3AT BELT HEADER PICKED UP LARGE ROCK FELT PAIN IN LEFT GROIN

BREAKING BANDS 2N CEMENT BLOCKS WITH HAND AXE.STRUCK THUMP WITH AXE CAUSING TO LEFT THUMB.

WHILE TRAMMING 5OADING MACHINE INTO SECOND CUT IN CROSSCUT,#6 PLACE,#4SECTON;THE CANOPY OF THE MACHINE STRUCK A LOOSE RIB PIN . THE PIN BENT BACK CAME LOOSE FROM THE RIB ENTERE THE MACHINE CAB3STRIKING THE OPERATOR IN THE MOUTH.

ELECTRICIAN WAS3WALKING DOWN TRACK FROM POWER CENTER AND TRIPPED OVER STEEL TIE.TWISTED LEFT KNEE.

WHILE LOADING M3NER GEARPOT ON JEEP WITH FORKLIFT WHILE PUSHING POT OFF FORKS WITH HAND POT MASHED FINGER AGAINST JEEP

A ROCKFALL WAS 8ISCOVERED BYFIRE BOSS MAKING HIS ROUNDS OUTBY THE ACTION #6 SECTION IN OLD WORKS IN AN INTERSECTION AT SPAD #5733.

EMPLOYEE WAS A 1ASSENGER ON A MANTRIP JEEP THAT CAME OFF THE TRACK.

WHILE SHOVELING3COAL FROM UNDER BELT,EMPLOYEE STRAINED BACK.

WHILE CROSSING 6ELT EMPLOYEE STEPPED OFF CONVEYOR STRUCTURE.INJURED ANKLE.

EE WAS LIFTING 7UTTING MACHINE CABLE SAID HE FELT PAIN IN LOWER ARM & ELBOW.

LIFTING LOADING3MACHINE TRAILING CABLE FELT PAIN IN LOWER BACK.

PULLING SHAFT O6T OF 6IN PUMP-SHAFT SLIPPERD OFF END OF PUMP HOUSING & FELL ON EMPLOYEES RIGHT HAND