Curles Neck Metal/Non-Metal

Employee just turned onto main haul road, went around a sharp curve and was on a straight stretch. He turned his wheel to the right to get more on his side of the road then turned back to the left to straighten up and it wouldn't turn left. Truck kept going to the right and went over the berm. Steering released, he turned to the left and the truck turned over.

EE WAS SHOVELING THE FEGO BOX ON THE CLASSIFIER TO CLEAN OUT SOME CONTAMINATED MATERIAL. HE FELTA PAIN IN HIS LOWER BACK MOVING A SHOVEL FULL OFMATERIAL.

EE WAS ATTEMPTING TO PUT A PUMP ON TO A BARGE DECK THAT WAS APPROX 5 FT ABOVE THE PLANT LEVEL HEWAS STANDING ON. AS HE WAS CLOSE TO SETTING THE PUMP ON THE BARGE HIS RIGHT FOOT SLIPPED CAUSING HIM TO TWIST HIS LOWER BACK DUE TO STILL HAVING THE PUMP IN HIS HANDS AND CATCHING HINSELF.

THE PNEUMATIC GREASE PUMP WASN'T WORKING SO EE WAS TRYING TO SEE WHAT WAS WRONG. HE TOOK THE PUMP COVER OFF AND HEARD AIR ESCAPING. HE PUT THE MIDDLE FINGER ON HIS LEFT HAND INTO THE PUMP BODY TO FEEL FOR AN AIR LEAK. AS HE DID THIS, THE PISTON WHICH WAS IN A RAISED POSITION CYCLED DOWN AND CUT THE FINGER OFF AT THE FIRST JOINT FROM THE FINGER TIP.

A PERIODIC CHEST X-RAY SCREENING WAS READ BY 2 "B" READERS. THE X-RAY WAS CHARACTERIZED AS CONSISTENT WITH PNEUMOCONIOSIS WITH READINGS OF Y1 & 0Y2. DAMAGE OR IMPAIRMENT CANNOT BE DETERMINED S OLELY BY READING THE CHEST X-RAY FILM.

EE WAS HANDING A WORN METAL SCREEN, THAT HAD BEEN CHANGED & CUT IN HALF OUT OF THE BARREL SCREENTO CO-WORKER. THE SURFACE HE WAS STANDING ON IS CURVED, THE NEW PLATE HAD A LIGHT FILM ON IT AND HIS SHOES WERE DAMP. AS HE HANDED THE PLATE OUT HIS RT. FOOT SLIPPED SIDEWAYS. WHEN HIS FOOT STOPPED HIS RT. KNEE BUCKLED AND HE FELT PAIN ON THE SIDE OF HIS KNEE.

EE WAS HELPING TO SHIFT A LOADED BARGE AT THE PLANT. HE WAS PULLING ON THE CABLE UP & OVER A CORNER BIT THAT WAS AROUND. THE CABLE STARTED TO TIGHTEN DUE TO NOT ENOUGH SLACK IN CABLE & REALIZE D HIS HANDS MIGHT GET TRAPPED BETWEEN BIT & THE TIGHTENING CABLE. HE PULLED THE CABLE UP REAL QUICK & FELT A BURNING SENSATION, SLIGHT PAIN IN HIS NAVAL AREA.

EE WAS IN PROCESS OF UNPLUGGING CHUTE. WHEN HE BENT DOWN, HIS HARD HAT FELL OFF. WHEN HE UPRIGHTED HIS HEAD STRUCK A SPRAY BAR CAUSING A LACERATION

THE INJURED RECEIVED FLASHBURNS AFTER LOOKING DIRECTLY AT AN ARC THAT WAS STRUCK BY A CO-WORKER.

EE STEPPED FROM BARGE ONTO THE TOP OF HORN BIT ON PLANT DECK AND TWISTED HIS KNEE.

ANOTHER EMPLOYEE THREW A BARGE DECKLINE TO THE INJURED EMPLOYEE TO TIE OFF A BARGE. THE ROPE WAS WET AND CONSEQUENTLY VERY HEAVY; HE STRAINED HIS RIGHT FOREARM WHEN HE CAUGHT THE ROPE.

EMPLOYEE WAS CLOSING CAB DOOR ON MOTOR GRADER WHEN THE DOOR GLASS BROKE AND LACERATED HIS WRIST.

EMPLOYEE WAS HELPING TO REPAIR CONVEYOR BELT ANDFELT DISCOMFORT IN HIS HIP AND LEG AS HE WAS CLIMBING DOWN FROM WORK AREA.

EE WAS CLIMBING FROM A LOADED BARGE ONTO AN EMPTY BARGE. AS HE PLACED HIS LEG ONTO THE EMPTY BARGE HE STRUCK HIS LEG AGAINST A JAGGED PIECE OF METAL ON THE WAISTRAIL.

EE WAS HELPING TO REPAIR CONVEYOR BELT AND FELT DISCOMFORT IN HIS HIP AND LEG AS HE WAS CLIMBING DOWN FROM WORK AREA.

EE WAS HOLDING A PIN MAUL WHILE CO WORKER USED A SLEDGE HAMMER TO REMOVE A DRAGLINE BUCKET TOOTH WHEN A PIECE OF THE PIN MAUL CHIPPED OFF AND STRUCK EE IN FOREARM.

EE WAS REMOVING ROCKS FROM A CONE CRUSHER AND STRUCK HIS ARM ON THE CRUSHER BODY.

EE WAS HELPING TO INSTALL CONVEYOR BELT WHEN HIS HAND WAS CAUGHT BETWEEN THE CHAIN HOIST & RETURN IDLER.

EMPLOYEE WAS WALKING ALONG DECK OF PLANT WHEN A WIRE ROPE CABLE USED TO MOVE BARGES WITH A WINCH BROKE AND STRUCK HIM IN THE FACE.

INJURED EMPLOYEE WAS HELPING CO-WORKERS REPLACE A HEAD PULLEY MOTOR SPROCKET, HE WAS STANDING ON THE HEAD PULLEY (CONVEYOR WAS DE-ENERGIZED AND LOCKED OUT) WHEN THE BELT BEGAN TO MOVE BACKWARD CARRYING HIM UNDER THE MOTOR FRAME AND A DISCHARGE CHUTE.

EMPLOYEE WAS HELPING TO REPAIR SAND SCREEN ON THE SECOND LEVEL OF PLANT. THE OXY-ACETYLENE HOSE WAS DRAPED OVER HANDRAIL AND ATTACHED TO TANKS LOCATED ON FIRST LEVEL. AS HE WAS PREPARING TO RE ACH FOR THE TORCH, THE WEIGHT OF THE HOSE PULLED THE TORCH OVER THE HANDRAIL AND IT "FLIPPED UP" AND STRUCK HIM IN THE MOUTH.

EE WAS CLIMBING ONTO A CLAMSHELL BUCKET TO ATTACH THE HOLDING LINE CABLE. AS HE PLACED HIS LEFT FOOT ONTO THE BUCKET AND "PUSHED OFF" WITH RIGHT LEG, HE FELT HIS LEFT KNEE "POP."

EMPLOYEE WAS HELPING TO ADJUST CONE CRUSHER. AN ATTACHMENT USED TO HOIST CRUSHER W/ LIFT CRANE FELL ON HIS FOOT. THE DEVICE WAS STORED ON CRUSHER PLATFORM AND THE VIBRATION FROM ADJUSTING CRUS HER CAUSED IT TO TIP OVER.

EMPLOYEE WAS WELDING ON SAND SCREW AND FELL FROM BROKEN BEAM TO BARGE DECK.

EE WAS CHANGING OIL ON FRONT END LOADER HE WAS USING AN EMPTY WIRE ROPE WOODEN SPOOL AS WORK PLATFORM TO SET USED OIL FILTER ON HE MOVED THE SPOOL ASIDE AND LATER WENT TO CHECK DIP STICK LE VEL. HE FORGET THAT SPOOL WAS NO LONGER BELOW EQQUIPMENT LADDER AND STEPPED BACK AND FELL ONTO THE GROUND.

EE WAS CHANGING DRAG BRAKE ON UNIT 204 DRAG LINE CRANE. HE WAS USING A ROPE TO PULL BRAKE BAND OUT WHILE STANDING ON DRUM AND FELT PAIN IN HIS ABDOMEN.

EMPLOYEE WAS HELPING TO DISMANTLE PIPELINE ON THE DREDGE "CAJUN QUEEN". HE AND A CO-WORKER WERE ATTACHING A CABLE ONTO EACH SECTION OF PIPELINE WHICH WAS THEN MOVED BY A MOTOR GRADER. EMPLOYEE TWISTED HIS KNEE WHILE DRAGGING THE CABLE TO ANOTHER SECTION OF PIPE.

EMPL HAVING DIFFICULTY STARTING GAS ENGINE 3" PUMP.HAD REMOVED AIR BREATHER COVER AND WAS PRIMING CARBURETOR WITH GAS.ENGINE BACKFIRED THROUGH CARBURETOR AND IGNITED SPILLED GASOLINE BURNING L EFT LEG.

HELPING TO REPLACE MAIN DRIVE SHAFT IN SNAD WINCH LIFTING SHAFT FORM WINCH HE CAUGHT HIS HAND BETWEEEN THE SHAFT AND WINCH FRAME HE WAS WEARING WORK GLOVES.

EMPLOYEE WAS SHORTENING DUMP CABLE ON DRAGLINE CRANE. THE CABLE SLIPPED OUT OF SOCKET AS HE WAS PREPARING TO SEIVE IN THE WEDGE AND STRUCK HIM IN THE MOUTH.

EMP WAS REMOVIN1 DISCHARGE LINE FROM OLD PUMP TO PUT ONTO NEW PUMP. HE WAS USING A PIPE WRENCH TO LOOSEN THE LINE. HE BEGAN TO STRIKE THE PIPE WRENCH WITH A SECTION OF 1 1/2 IN METAL PIPE AN AND STRUCK HIS 5EFT THUMB

EMPLOYEE WAS HE5PING TO CHANGE SCREENS IN THE 8 FT X 16 FT VIBRATOR ON PLANT 12 HE AND A COWORKER WERE PUTTING A 4 FT X 4 FT SECTION IN PLACE AND HE CAUGHT HIS FINGER BETWEEN THE SCREEN AND CENTER RAIL HE3WAS WEARING WORK GLOVES

THE CRANE OPERA7OR AND OILER ON 11 WORK RIG HAD BEEN CLEANING A SAN BARGE WITH A SMALL FRONT END LOADER. THE LOADER WAS LIFTED BACK ONTO THE DECK OF THE WORK RIG, THE OILER DISCONNECTED THE SL INGS AND HAD RE5TTACHED THE CLAMSHELL BUCKET. HE TURNED TO GO AND MOVE THE F.E. LOADER. THE CRANE OPERATOR BEGAN HOISTING BUCKET. AS SOON AS THE END OF BUCKET CLEARED THE TIMBERS THAT THE CRA

EMPLOYEE WAS HA6LING MATERIAL FROM SAND AND GRAVEL PIT TO PROCESSING PLANT. HE CROSSED THE LEFT LAND OF HAUL ROAD AND RAN OFF THE LEFT SHOULDER OF HAUL ROAD. THE HAUL WAGON TURNED OVER ON ITS LEFT SIDE AND 9MPLOYEE BRUISED HIS KNEE. INSIDE THE CAB.

INJ LUBRICATING3MASTER CLUTCH ASSEMBLY ON CLAMSHELL CRANE.DIDNT SHUT DOWN ENGINEAND LIFTED UP HINGED GUARD TO REMOVE OIL PLUG WITH WRENCH.FLY WHEEL WAS STILL TURNING AND CAUGHT SIDE OF RIGHT H AND.EMPL NOT WE5RING WORK GLOVES.