Fredrickson Pit Metal/Non-Metal

Door on loader swung open hitting him on head.

Stepped down off a dozer slipped & fell between truck & dozer frame. Suture Rt.ear/ACL tear

EE WAS GETTING OFF LOADER - SLIPPED - FELL TO THE GROUND (LOWER BACK INJURY). 3/19/05: EE INFORMED EMPLOYER THAT HE WOULD BE SEEKING OPERATION OR ? FOR HIS BACK.

EE LIT A PROPANE TORCH AFTER CLEANING THE SURFACE WITH SOLVENT.

HE INSTALLED SPRINGS IN THUNDERBIRD SCREEN, SMASHED FINGERS (2) ON LEFT HAND WHEN JACK SLIPPED.

FRONT LOADER SEAT BROKEN, CAUSING JARRING OF BACK.

HOLDING STEEL PLATE WHILE IT WAS BEING HIT WITH HAMMER TO DRIVE BUSHING IN. PLATE BOUNCED MOVED AND LEFT LITTLE FINGER TIP WAS SMASHED UNDER PLATE.

BUMPED ELBOW (DOESN'T RECALL BUMPING) - ELBOW BRUISED.

WORKING ON ENGINE HEAD, IT ROLLED OVER & CAUGHT HIS RIGHT HAND.

HITTING A BOLT OF A PADDLE, HE MISSED & HIT HIS HAND.

HIT BUMP WHILE IN LOADER- BOUNCED SIDEWAYS FELT SHARP PAIN IN LOWER BACK.

TWISTED KNEE/HIP WHEN GOT CAUGHT BETWEEN FRAME AND CAB OF LOADER WHILE SERVICING IT.

MOVED TAIL PULLEY FROM BOTTOM CROSS BELT DROPPED ON RT. FINGR AND CUT IT.

WASHING TRUCK HAND SLIPPED CUT FINGER ON FENDER.

WAS ADJUSTING CONVEYOR WIPER AND WAS CAUGHT BY BELT.

EMPLOYEE WAS STIRRING SOLVENT AND SPLASHED SOME OF THE SOLVENT INTO HIS RIGHT EYE.

EMPLOYEE REINJURED RIGHT HAND FROM PREVIOUS INJURY ON 04/19/99. HE TWISTED INJURED HAND WHILE CLIMBING DOWN FROM LOADER.

REPAIRING U JOINT. POUNDING HAMMER PIECE OF STEEL CHIPPED OFF AND CUT HAND.

INSTALLING STEERAXLE ASSY ON 580 CASE TRACTOR, LINED UP AXLE, PUT IN PIVOT PIN. COMPLETED. CLIMB OUT FROM UNDER TRACTOR AND COULD NOT STRAIGHTEN UP.

CUT RIGHT INDEX FINGER WHEN CRUSHED BETWEEN TRANSMISSION MOUNT OF DUMP TRUCK AND FRAME.

HE WAS CRAWLING UNDER A TRUCK, BUMPED THE CONTAINER OF SOLVENT. IT SPLASHED INTO HIS EAR.

CLEANING OUT UNDER TROUGHING ROLLERS, HAND WENT BETWEEN ROLLERS AND BELT.

DROPPED A TOOL- TRIED TO RETRIVE QUIKLY- HIT FAN ON ENGINE WITH RIGHT HAND CAUSING TO CUT SMALL RT. PINKY FINGER.

CUT RUBBER WITH UTILITY KNIFE TOWARDS HIMSELF, KNIFE STUCK HIS KNEE CUTTING IT.

EXCESSIVE BOUNCING WITH IMPROPER SEAT SEAT HAS BEEN REPLACED.

FELL OFF SCREEN 2 LANDING ON LEFT ARM.

HE PRYED A ROCK WEDGE IN JAW WITH BAR, ROCK ROLLED ONTO BAR CAUSING BAR TO MOVE UPWARD STRIKING HIS CHIN.

CRAWLED OUT OF HOPPER. CONVEYOR TURNED ON. WAS PULLED UNDER BELT.

WHILE REINSTALLING DISTRIBUTOR PLATE ONTO CRUSHER, IT SLIPPED OUT OF HANDS AND HE DROPPED IT ON TOES.

EE WAS FIXING LIGHT ON 3 AXEL TRAILER, RAISED UP AND BASHED HEAD INTO CORNER OF STEEL PLATE. CUT HEAD OPEN ABOVE LEFT EYE.

WALKWAY BROKE.

GRINDING METAL WITH HAND GRINDER AND SLIPPED.

HAND RAIL ON STAIRS WAS MUDDY AND COLD.

INJURED EE WAS DRIVING ROCK TRUCK TOWARDS INTERSECTION AND HE COLLIDED WITH TRAILER OF DUMP TRUCK. VISIBILITY WAS GOOD UP TO 150 FT. IN ALL DIRECTIONS OF TRAVEL AND BOTH DRIVERS HAD AMPLE TIME AND DISTANCE TO AVOID THE ACCIDENT.

INDIVIDUAL WAS REMOVING BOLTS THAT HOLD LEFT FRONT SPRING IN PLACE. HE WAS DOWN ON HIS KNEES USING A WRENCH TO LOOSEN A BOLT. HE WAS PULLING THE WRENCH TOWARD HIM WHEN IT SLIPPED AND HIT HIM IN THE HEAD.

HE WAS ROLLING A BIG ROCK FROM UNDER FEED HOPPER AS HE ROLLED HE FELT A STRAIN IN GROIN AREA.

MECHANIC WAS REMOVING A BEARING RACE FROM A WHEEL HUB HE WAS HOLDING A DRIFT WITH HIS LEFT HAND & USING A HAMMER WITH HIS RT HE STRUCK THE DRILL & THE HAMMER SLIPPED TO THE SIDE STRIKING THE B ACK OF HIS THUMB

EMPLOYEE WAS WORKING WITH ANOTHER EMPLOYEE USING A MAGNETIC DRILL TO DRILL HOLES IN BOTTOM OF A LOADER BUCKET IT HAD TO BE PLACED INTO POSITION & ATTACH3ED TO DRILL EACH HOLE 12 HOLES TO DRILL ED DRILL WEIGHES APPROX 40 LBS

EMPLOYEE IS MECHANIC IN COURSE OF ROUTINE DUTE DUST BLEW INTO LEFT EYE. HE DID NOT REPORT UNTIL IT BECAME PAINFUL 2 DAYS LATER.

INJURED WAS REPAIRING A BROKEN WIRE UNDER DUMP TRUCK. AS HE WAS GETTING OUT FROM UNDER THE TRUCK HE RAISED HIS HEAD AND HIT IT ON THE METALOF THE TRUCK CHASSIS.

INJURED WAS STANDING ON CRUSHER TIGHTENING BOLTS& SLIPPED ON OIL SPOT AND FELL LANDING ON LEFT SHOULDER.

EMPLOYEE WAS REPAIRING CONVEYOR BOLT HIS HAND SLIPPED AND HE JABBED HIS LEG WITH A UTILITY KNIFE ABOVE THE KNEE.

EMPLOYEE WAS OPENING JAW CRUSHER COVER TO CLEAR CRUSHER OF OVERSIZE MATERIAL

EMPLOYEE WAS POSITIONING CHUTE TO BE WELDED WHEN IT SHIFTE DAND STRUCK HIM ON LEFT LEG.

EMPLOYEE WAS REMOVING STEEL LINER FROM DUMP BED WITH CUTTING TORCH WHEN THE LAST CUT WAS MADE HE INTERNAL STRESS OF THE BOLT PLATE CAUSED IT TO SPRING UP LACERATING HIS SCALP REQUIRING 7 SUTUR ES

EMPLOYEE WAS INSTALLING TRUCKDOOR IN SHOP & DROPPED IT ON HIS FOOT DOOR WEIGHED APPROX 35# & FELL 36IN EMPLOYEE WAS NOT WEARING SAFETY TOE SHOES

EMPLOYEE WAS CLEANING A CONVEYOR ROLLER AND HIS HAND WAS PINCHED BETWEEN THE ROLLER AND THE CONVEYOR BELTING.

EMPLOYEE WAS GRINDING METAL WITH A HAND HELD GRINDER AND ALLOWED THE PORTION OF THE GRINDING WHEEL THAT WAS NOT GAUROED TO TOUCH HIS LEG CAUSING AN ABRASION.

USING RAM CYLINDER FELL ON HIS SIDE

EE AND PARTNER WERE ASSEMBLING CONE CRUSHER HE BRACED HIMSELF FOR LEVERAGE AND TWISTED HIS BACK.

EMPLOYEE WAS CLEANING MATERIAL OFF OF A RIPPED BELT TO BEGIN THE REPAIRS. HE SLIPPED ON LOOSE MATERIAL ON THE BELT AND FELL AGAINST HIS SHOVEL DISLOCATING HIS SHOULDER.

LARGE ROCK APPR2X. 150# FELL FROM CONVEYOR FEEDING JAW CRUSHER STRIKING EMPLOYEE ON THE BACK OF HEAD RESULTING IN SKULL FRACTURE AND FRACTURE OF RIGHT ARM.