Livingston Plant #1672 Metal/Non-Metal

Helping wash material off mill head and put chains on head for lifting when chain head rolled on top of right foot. Cause a broken big toe on right foot

While shooting a ring in kiln #2 the employee felt excessive recoil then noticed EE was bleeding from EE's right thumb

The employee was helping another employee move a Winchester Ringbuster kiln gun from the kiln deck to the storage area of the mine. The gun discharged while the employees were lifting it. This resulted in the slug striking the employee in left foot.

Employee cut left knuckle on electric Metabo saw while cutting notches on idler roller. Employee received four stitches.

Employee and a co-worker were removing port-a-power heads from under kiln. The third and last one slipped out of co-workers hand and employee could not get their hand away in time and the head caught the end of EE's finger. The tip of the middle finger was broken and lacerated by the 275 pound port-a-power head.

EE was leaving his work location in the Shipping Tower, decending the steps from the 3rd level. Prior to reaching the 2nd level landing, he looked back up at the 3rd level and noticed he had left the Load Out Chut in the down position. He was not paying attention to the steps and and missed the bottom step, twisting his right ankle, examined by MD, put on restricitons.

WHILE INSTALLING SHOTCRETE IN ROTARY KILN, EMPLOYEE WAS STRAINING TO GET A CLAMP ON PUMPING HOSE. FELT PULL IN CHEST. CONTINUED TO WORK FOR A BIT THEN LEFT JOBSITE. COULD NOT BREATHE, HAD CHEST PAIN. EMPLOYEE WAS TAKEN FOR MEDICAL ATTENTION.

The employee was preparing to grease a bearing on a conveyor. He bent over at the conveyor and strained his lower back.

The employee was tightening bolts on a crusher head. While he was pulling on the torque wrench, his footing and wrench slipped causing a lower back strain.

The employee was removing a lump of clay from a conveyor. The weight of the clay was approx. 15 lbs. As the employee reached to remove the clay from the belt he felt a pull in his right arm (bicep). The employee has a possible torn tendon in the right arm next to the shoulder.

The employee was preparing to trim skirts on a belt conveyor. The employee exposed the blade of the cutter before positioning himself in firm working position. As the employee tried to position himself to complete the work he punctured and lacerated the left wrist.

The employee was preparing to replace a door on the back portion 6X16 Shaker Screen. The employee pulled a muscle on the right side of his back.

The employee was preparing to climb a ladder and lost his footing on the bottom step. The employee slipped and fell about 8" onto his bottom.

The weather before the start of the employee shift was humid and there had been previous heavy rains. The employee was decending on a flight of stairs. The employee slipped causing the employee to fall down the steps. The employee had bruising of the rt. hip and rt. forearm.

The employee was preparing to change a hydraulic line on a WA 450 loader. The line was in a area that had limited access. The employee turned to access the ladder and felt a pull in his lower back.

THE EE WAS CUTTING SKIRTS FOR A BELT CONVEYOR. THE BOX CUTTER SLIPPED FROM THE SURFACE OF THE BELT, AND CUT THE EE'S LEFT LEG.

THE EMPLOYEE WAS CLIMBING UP THE LADDER ON A FRONT END LOADER WHEN HE FELT SOMETHING POP IN HIS LEFT ELBOW. THERE WAS NO TRAUMA TO THE ELBOW. NO DEFECTS WERE FOUND BUT THE INVESTIGATION IS CON TINUING.

IMPROPER BODY POSTURE. THE EE WAS REACHING FOR A ROLLER HOUSING AND PULLED A MUSCLE IN THE UPPER RIGHT PORTION OF HIS BACK.

THE EE WAS POKING AT MATERIAL THAT WAS IN AIRGATE. WHEN THE EE CONTINUED POKING HE PULLED SOME MUSCLES IN HIS SHOULDER.

THE EE WAS RUNNING UP THE STAIRS OF THE CRUSHING DEPT. AS THE EE WAS RUNNING HE TWISTED HIS ANKLE.

THE EE THREW THE OFF SPEC CHUTE. WHEN THE KILN GOT BACK ON SPEC, THE EE HAD TO PULL THE CHUTE BACK UP IN ORDER FOR THE MATERIAL TO GO TO THE STOCKPILE. WHEN THE EE THREW THE CHUTE, HE PULLED A MUSCLE IN THE MIDDLE OF HIS BACK.

THE EE WAS CLEANING & SHOVELING UNDER THE TAIL PULLEY. WHEN THE EE STOOD UP FROM SHOVELING HE FELT A PAIN IN HIS UPPER & LOWER BACK.

THE EE WAS SPLICING A WIRE ON TOP OF THE #3 KILN BACKEND. THE WIND STARTED BLOWING DUST FROM THE STOCKPILE & THE KILN BACKEND. NO MATTER WHAT DIRECTION THE EE TURNED, THE DUST STILL GOT IN HIS EYES.

THE EE WAS CLIMBING DOWN OFF OF THE TRACKHOE. WHEN THE EE PUT HIS FOOT DOWN HE THOUGHT HE WAS STEPPING DOWN ON SOLID GROUND. BUT THE GROUND WAS EXTREMELY SOFT. WHEN THE EE STEPPED DOWN INT HE MUD, HIS FOOT SANKED IN THE MUD AND HIS FOOT TURNED TO THE SIDE. THIS CAUSED HIM TO BE OFF BALANCE AND TO PUT TOTAL WEIGHT ON ANKLE.

THE EE WAS CLIMBING DOWN OFF THE CLAYSHED LADDERAFTER A HOSE HAD COME LOOSE.

THE EMPLOYEE WAS CLEANING UNDER THE CRUSHER WITH THE BOBCAT. THE EMPLOYEE WENT NEAR THE EDGE OF THE GROUND TO CLEAN AND CROSSED SOME UNLEVEL GROUND. WHEN THE EMPLOYEE CROSSED THE UNLEVEL GROUN D HE FELT HIMSELF ABOUT TO TIP OVER. IN REACTIONTHE EMPLOYEE STUCK HIS HAND OUT OF THE BOBCAT AND GOT IT SMASHED BETWEEN THE BAR AND NEARBY CAT WALK.

EE JUMPED FROM THE LEDGE AROUND THE #3 COOLER AND CAUSED PAIN TO HIS RIGHT KNEE.

EE WAS SHOVELING UNDER THE #2 TAIL PULLEY & THE EE BENT UNDER THE CATWALK TO GET TO THE OTHER SIDE. WHEN THE EE TRIED TO GET UP HE FELT A POP IN HIS BAKC

THE EMPLOYEE WAS TRYING TO WARN ANOTHER EMPLOYEETHAT WAS ON A FORKLIFT WITH A MOTOR. THE FORKLIFT GOT HUNG ON THE DOOR. THE EMPLOYEE NOTICED THAT THE BOOM AND THE MOTOR WERE HUNG ON THE DOOR AND TRIED TO WARN THE OPERATOR. IN THE PROCESS THE EMPLOYEE'S HAND WAS WAVING BETWEEN THE STUCKMOTOR/BOOM AND THE I-BEAM. THE BOOM CAME LOOSE AND THE EMPLOYEE WAS HIT IN THE HAND.

THE EE WAS FEEDING THE HOPPER AND NOTICED THAT THE FEED WAS NOT GOING UP THE BELT. THE EE GOT OFF THE LOADER AND RAN TO THE HOPPER TO CUT OFF ALL THE CONTROLS. IN THE PROCESS OF THE EE RUNING TO HOPPER. HE TWISTED HIS RIGHT ANKLE.

THE EMPLOYEE WAS TRYING TO UNSTOP A CLAMGATE. THE EE TRIED TO UNSTOP THE CLAMGATE BY USING THE HANDLE. THE EE'S HAND SLIPPED OFF THE HANDLE. THIS CAUSED THE HANDLE TO COME BACK UP AND HIT T HE EMPLOYEE IN THE HAND.

EE WAS PULLING A SECOND BATTERY FROM A FORKLIFT.THE WEIGHT OF THE BATTERY WAS PLACED ON HIS RIGHT ARM. THIS CAUSED HIM TO FEEL A PULL & BURNING SENSATION.

THE EE WAS WALKING TO HIS LOADER. IN THE PROCESS, THE EE STEPPED IN A MUDYY AREA. THE EMPLOYEE'SFOOT/LEG WENT INTO MUD ABOUT 6 INCHES. WHEN EE PULLED HIS LEG OUT OF THE MUD HE FELT SOME PAIN.

THE EE WAS PLACING A 55 LB APPROX. CYLINDER ON A TABLE. IT WAS NOT A STRAIN ON THE EMPIRE TO REMOVE THE CYLINDER INITALLY.

THE EE WAS JACKHAMMERING IN THE KILN AND FELL. THE EE FELL ON THE LOOSE MATERIAL IN THE KILN.

EMPLOYEE WAS USING A FORK DEVICE TO TURN OVER A 2000 LB PERILING, WHILE HE WAS IN THE PROCESS OF TURNING THE PERILING OVER WITH FORK DEVICE, AN EMPLOYEE ASKED HIM A QUESTION, AS HE TURNED HIS CHHEK TO RESPOND TO THE EMPLOYEE, HE CUT HIMSELFWITHT THE TOP OF THE FORK DEVICE.

EE WAS REPAIRING THE HYDRAULIC LINES ON THE KOMATSU LOADER WHEN THE EE REMOVED HIS BODY FROM THELOADER HE CUT HIS EAR ON THE WHEEL WALL OF THE LOADER

WAS CUTTING THE LID OFF OF A PLASTIC CONTAINER WHEN THE KNIFE SLIPPED AND CUT HIS LEFT ARM NEAR THE ARTENAL VEIN.

THE EE WAS WORKING ON THE #1 SILO CONVEYOR BELT. THE EE WAS TAKING SAFETY PERCAUTIONS BY WEARING HIS SAFETY GLASSES.

EMPLOYEE WAS HELPING SUPERVISOR PUT A GUARD ON THE #3 FAN AND THE #2 COOLER. AS THE SUPERVISOR LET GO OF THE GUARD, THE EMPLOYEE WAS STILL HOLDING THE GUARD. WHEN THE GUARD CAME DOWN, IT FELL ON HIS RIGHT HAND.

THE EMPLOYEE WAS CLEANING THE TRAYS OF THE TRUNNION ROLLERS ON THE 3RD PIER AT THE #3 KILN. AS HE WAS COMING DOWN OFF THE PEIR AND ONTO THE CATWALK, THE EMPLOYEE STEPPED ONTO A BLOCK THAT WAS ON THE WALKWAY. THERE WAS A CONTRACTOR PRESENT AT THE SITE. EMPLOYEE WAS BEING CARELESS, BUT CATWALK NEEDED TO BE CLEAR OF DEBRIS.

ASSISTING NEW EE IN ASSEMBLING HARD HAT BAND SLIPPED DOWN INTO HARD HAT AND THUMB STRUCK SIDE OF HAT, PULLING NAIL BACK CAUSING A TEAR ON SIDE OF THUMB NAIL.

EE WAS RETURNING FROM LUNCHBREAK WHEN SHE FELT A SMALL STONE IN HER BOOT. SHE WAS ATTEMPTING TO WALK ON HER TIP TOE TO FIND A PLACE TO SIT & REMOVE BOOT WHEN SHE TWISTED HER ANKLE

EE WAS SWINGING A HAMMER AND PULLED MUSCLE IN BOTH SHOULDERS.

EE WAS ASSISTING IN THE INSTALLATIO OF BAGS IN THE DUST SYSTEM BAGHOUSE. HE SLIPPED ON THE LADDER STRIKING ELBOW ON THE LADDER REFUSED MED TR EATMENT DID NOT REQUEST MED TREATMENT UNTIL 7/28/ 99

SHOVELING COAL OFF SILO ROOF RESULTED IN LOWER BACK STRAIN Y

EMPLOYEE WAS TRYING TO REVERSE THE DISCHARGE CONVEYOR TO GET A ROLLER OUT OF THE TAIL PULLEY. HE PULLED THE BREAKER AND LOCKED IT OUT. HE THEN STUCK HIS SCREWDRIVER INTO THE BOX AND TOUCHED THE ENERGIZER MECHANISM. THE WIRES ON THE TOP OF THE BREAKER WERE STILL HOT BECAUSE THE MAIN WAS NOT PULLED.

EE WAS ATTEMPTING TO SECURE A COAL MILL JOURNAL TO A FORKLIFT USING A COME-A-LONG. WHEN THE FORKLIFT STARTED TO MOVE, THE CHAIN SLIPPED STRIKING THE EE IN THE MOUTH. EE SUFFERED A LACERATION R EQUIRING STITCHES.

EE WAS TURNING TO GET AN OIL BUCKET WHEN HE FELT HIS BACK "GIVE OUT". HE SUFFERED A BACK STRAIN FROM IMPROPER BODY MOVEMENT.

EE WAS CHANGING THE OXYGEN BOTTLE ON THE WELDING TRUCK WHEN HE SMASHED HIS FINGERS BETWEEN THE OXYGEN BOTTLE & TRUCK CAUSING A FRACTURE OF THE 3RD & 4TH FINGERS ON THE LEFT HAND.

EE WAS RETREUVUNG A BUCKET HE DROPPED IN THE SHIPPING TUNNEL. HE DUCKED UNDER THE CROSS BRACE IN THE TUNNEL & RETREIVED THE BUCKET. WHEN RETURNING, HE CAME UP UNDER THE CROSS BRACE TOO SOON ST RIKING IT WITH HIS FACE CAUSING A SMALL CUT ON THE BRIDGE OF NOSE.

EMPLOYEE WAS HSOVELING OUT FROM UNDER THE DISCHARGE CONVEYOR WHEN HE PULLED HIS LOWER BACK.

EMPLOYEE WAS ATTEMPTING TO REPAIR A CIRCUIT BREAKER ON A TRANSFORMER. WHEN HE RECONNECTED THE ELECTRICITY TO THE TRANSFORMER IT BLEW CASUING A BRIGHT FLASH OF LIGHT. EMPLOYEE SUFFERED A MILD B URN TO HIS EYES SIMILAR TO THAT OF A WELDERS BURN.

EE WAS ASSISTING IN THE REINSTALLATION OF THE BLADE ON THE MOTORGRADER. THE CHAIN ON THE COMEALONG SLIPPED RELEASING THE HOLD ON THE BLADE CAUSING IT TO STRIKE THE EE ON THE TOP OF HIS RIGHT STEEL TOED BOOT. RESULTED IN A FRACTURE OF HIS BIG TOE.

EE WAS ASSISTING MAINTENANCE MANAGER IN CHANGING 6" SUCTION HOSE ON PIT PUMP. WHEN THE HOSE RELEASED FROM THE PUMP THE COUPLING ATTACHED STRUCK EE IN THE CHIN. EE HAD TO HAVE SUTURES IN THE LA CERATION ON CHIN.

REPETITIVE MOTION.

EE WAS CLEANING UNDER #4 CONVEY0R BELT WITH THE FRONT END LOADER WHEN HE STRUCK A CONCRETE SLAB WITH THE BUCKET OF THE LOADER. THE IMPACT OF THECOLLISION CAUSED HIM TO STRIKE HIS HEAD ON THE C AB WALL CAUSING A LACERATION REQURING 3 SUTURES

EMPLOYEE WAS TRYING TO UNSTOP THE CHUTE UNDER TEH #4 SILO. WHILE HE WAS CLEANING THE MATERIAL OUT FROM THE AIRGATE, IT CLOSED CAUSING HIS FINGER TO JAM AGAINST THE CHUTE.

EMPLOYEE WAS CARRYING A BATTERY TO INSTALL IN A LOADER WHEN HE FELT A MUSCLE PULL IN HIS UPPER BACK.

EE WAS CLEANING INSIDE PRIMARY HOPPER WITH A PICK AND ROD. HE TURNED HIS BODY INCORRECTLY AND PULLED A MUSCLE IN HIS BACK.

IT WAS WINDY AND THE EE WAS CLEANING UP IN THE PLANT AREA WHEN THE WIND BLEW XXX DUST IN THE EE'S EYES. EE HAD HIS SAFETY GLASSES ON.

EE WAS ASSISTING IN BREAKING EXCESS BUILUP FROM #3 SCRUBBER WALL. A SIZEABLE PIECE OF THE BUILUP FELL FROM THE WALL STRIKING HIM ON THE LEFT SHOULDER AND ELBOW.

EE WAS ASSISTING IN THE REINSTALLATION OF THE GUARD OVER THE V BELTS ON THE 3 CRUSHER. HE WAS NOT WEARING WORK GLOVES AT THE TIME HE CUT HIS FINGER ON THE GUARD S EDGING.

EE WAS LIFTING THE #3 SCRUBBER BLOWER NOZZLE WHEN IT SLIPPED FROM HIS GRIP STRIKING HIS PINKY FINGER. HIS FINGER TIP WAS CUT IN A SEMI-CIRCULAR OPENING.

EMPLOYEE WAS GRINDING ON KILN #3 CRANKHEAD SHAFT. ANOTHER EMPLOYEE TRIPPED OVER THE EXTENSION CORD TO THE GRINDER, CAUSING THE GRINDER TO SLIP. THE GRINDER THE STRUCK EMPLOYEE ON THE FINGER CAUSING A CUT. IF EMPLOYEE WAS WEARING GLOVES, HE MAY NOT HAVE BEEN INJURED.

EE WAS CHECKING OIL ON THE TRUNNION ROLLER WHEN HE SLIPPED OFF THE CONCRETE PLATFORM AND FELL TOTHE CATWALK APPROX. 2 1/2 FEET BELOW. HE SUFFERED A FRACTURE OF THE C-6 VERTABRE AS A RESULT OF THE FALL. IT WAS RAINING AT THE TIME.

EE WAS WORKING ON #2 KILN INLET WHEN THE WRENCH HE WAS USING SLIPPED & HIT HIS HAND. HIS HAND THEN HIT AN ANGLE CAUSING A CUT ON HIS FINGER REQUIRING TWO STITCHES.

EMPLOYEE WAS CLOSING THE TAILGATE ON THE DUMP TRUCK HE WAS OPERATING. HE MADE AN ATTEMPT TO REMOVE SOME MUD FROM THE TAILGATE WHILE TRYING TO CLOSE IT. THE TAILGATE STRUCK HIS FINGER DURING TH E PROCESS.

EMP WAS UNSTOPPING THE STARFEEDER CHUTE. WHEN HEWENT TO CLOSE THE CHUTE DOOR THE SUCTION FROM THE FAN PULLED THE DOOR TO. HIS FINGER WAS CAUGHT BETWEEN THE DOOR AND CHUTE.

EE WAS USING THE JACKHAMMER TO REMOVE OLD CASTABLE LINING FROM KILN 2. HIS GRIP SLIPPED CAUSING THE JACKHAMMER TO LAND ON HIS LEFT FOOT. HE SUFFERED A BROKEN TOE.

EMPLOYEE WAS ASSISTING IN REPLACING IDLERS ON TUNNEL BELT IN THE SHIPPING DEPT. ANOTHER EMP WAS HOLDING UP THE BELT WITH A PIPE, WHEN THE PIPE SLIPPED, STRIKING EMP'S MIDDLE FINGER.

EMPLOYEE WAS HELPING REPAIR #2 DRIVE CHAIN.HE REACHED ACROSS THE CHAIN AND HIS GLOVE CAUGHT ON A BOLT CAUSING HIS ARM TO BE PULLED INTO OR AGAINST THE CHAIN.EMPLOYEE SUFFERED LACERATIONS AND S OME TEAR IN SMALLER LIGAMENTS TO HIS RIGHT FOREARM.

EMPLOYEE WAS ATTEMPTING TO CLEAN GREASE PUMP WHEN HE STUCK HIS FINGER INTO THE PUMP TO REMOVE GREASE AND DIRT IN THE CYLINDER. THEN TURNED THE GUN ON WITH HIS LEFT HAND CAUSING THE INTERNAL CY LINDER TO OPERATE WHICH AMPUTATED FINGER TIP.

EE WAS ASSISTING IN JACKING UP KILN #2 AT PIER 3 WITH 250 TON JACKS AND ELECTRIC POWER UINIT. AS JACKS WERE BEING RELEASED ONE AT A TIME, THE VERTICAL HEIGHT DIFFERENCE BETWEEN THE JACKS CAUSE D THE SADDLE TO INCLINE TO ONE SIDE. THE PRESSURE BEARING DOWN ON THE SADDLE CAUSED A FILLER BAR TO SHOOT OUT AND STRIKE EE ON HIS LEFT HAND.

EE WAS ASSISTING COWORKER IN PUTTING THE DUST CHUT BACK ON #3 KILN INLET SEAL. COWORKER WAS LEANING ACROSS A HANDRAIL AS HE WRAPPED A CHAIN AROUND THE CHUTE. EE WAS STANDING BESIDE HIM WITH HI S HAND ON THE HANDRAIL. THE WELD ON THE HANDRAIL BROKE UNDER THE WEIGHT OF COWORKER CAUSING THE CHUTE TO SHOOT FORWARD STRIKING EE'S HAND CAUSING THE INJURY.

EE STATED THAT HE WAS SHOVELING UNDER 1 PRIMARY CRUSHER INCLINE BELT. WHEN HE ROSE TO DUMP THE FEED CLAY ONTO THE BELT, HE FELT A PAIN IN HIS BACK.

EE WAS WALKING DOWN THE STEPS FROM THE KILN PLATFORM. WHEN HE REACHED THE BOTTOM, HE STEPPED OFF INCORRECTLY AND TWISTED HIS ANKLE.

EMPLOYEE WAS REPLACING #3 COOLER DRIVE CHAIN SPROCKET. HE USED HIS FOOT TO PUSH THE SPROCKET ON THE SHAFT WHEN HIS FOOT SLIPPED CAUSING HIS LEG TO STRIKE AGAINST THE SPROCKET.

EMPLOYEE WAS LIFTING JACKS ONTO PIER 2 OF KILN #1 WHEN HE PULLED THE MUSCLE IN HIS RIGHT SHOULDER

EE AND EMPLOYEE WERE JACKHAMMERING IN KILN #@. EE STOPPED TO REST. EMPLOYEE JACKHAMMER SLIPPED AND STRUCK EE ON THE FINGER RESULTING IN A CRACK OF THE BONE.

EMPLOYEES HAND SLIPPED WHILE TURNING A WRENCH LACERATING THE LONG OR MIDDLE FINGER OF HIS LEFT HAND THE WOUND WAS TREATED ON SITE WITH FIRST AID PROCEDURES(DISINFECT ANT & BANDAGE) AFTER SWELL ING WAS NOTED 05-09-95 DOCTOR TREATED EMPLOYEE FOR CELLULITIS

DUST COAL IGNITED IN #3 KILN CAUSING AN EXPLOSION.

EMPLOYEE PULLEDTHE MUSCLE IN HIS LOWER BACKWHILE MOVING HYDRAULIC JACKS

THEY WERE ABOUT TO RECONNECT BROKEN COAL ELEVATOR CHAIN. THEY WERE TRYING TO UNTANGLE THE TRACE CHAIN FROM THE ELEVATOR CHAIN. BEFORE THEY COULD ATTACH THE TRACE CHAIN FOR SAFETY, A SLIGHT JAR OF THE BUCKET CAUSED THE CHAIN TO TUMBLE DOWN THE ELEVATOR SHAFT.

EMPLOYEE WAS ATTEMPTING TO OPEN THE TRAP DOOR ON A RAILCAR HE WAS CLEANING WITH A CROWBAR. WHEN THE CROWBAR RELEASEAD FROM ITS HOLD, EMPLOYEE TWISTED HIS BODY FROM THE FORCE HE WAS EXERTING UP ON THE CROWBAR. HE TWISTED HIS ANKLE SIDEWAYS & THEN PLACED THE ENTIRE BODY WEIGHT UPON THE ANKLE. THE BODY WEIGHT PUT UPON THE TWISTED ANKLE CAUSED A FRACTURE OF THE RIGHT ANKLE.

EMPLOYEE WAS WELDING ON #2 COOLER WHEN THE SUPPORT THROAT SLIPPED STRIKING EMPLOYEES RT INDEX FINGER

EMPLOYEE WAS ASSISTING IN UNSTOPPNG PIPE ON #3 SCRUBBER WHEN HOT WATER CAME OVER THE TROUGH INSTEAD OF THROUGH IT. EMPLOYEE JUMPED OFF THE CATWALK TO THE GROUND, ABOUT 5'. HE LANDED HARD ON HIS LEG CAUSING PAIN IN THE RIGHT KNEE.

HEAVY RAINFALL IN THE AREA OVER THE PAST FEW DAYS HAD LEFT THE PLANT AREA WET AND MUDDY. EMPLOYEE WAS PUSHING A FULLY LOADED WHEELBARROW AROUND THE KILN #2 AREA. HIS FEET SLIPPED IN THE MUD A ND HE LOST HIS BALANCE AND FELL DOWN IN THEMUD LANDING ON BOTH KNEESUNTO A CONCRETE SLAB.

THERE HAD BEEN ALOT OF RAIN OVER THE PAST COUPLE OF DAY SNA DHTE GORUND WAS WET AND MUDDY AS A RESULT. THE EMPLOYEE IS FAIRLY NEW AND WAS NOT ACCUSTOMED TO THE CONDITIONS WHEN THERE HAS BEEN ALOT OF RAIN. THE EMPLOYEE SLIPPED WHILE WALKING THROUGH THE CLAY SHED AND FELL IN THE MUD.

EMPLOYEE WAS ASSISITING IN THE REPAIR OF #3 CONVEYOR BELT. TWO OTHER EMPLOYEEES WERE STRETCHING A CABLE WHEN ONE OF THE EMPLOYEES ACCIDENTLY RELEASED HIS END. THE CABLE SNAPPED BACK STRIKING I NJURED ON THE RIGHT ANKLE.

THE EMPLOYEE WAS HELPING TO REMOVE A RING IN THE #2 KILN USING A SHOTGUN. HIS SHOULDER BECAME SORE THE NEXT DAY.

WHILE CLEANING #3 SCRUBBER, A LARGE CHUNK OF LIME FELL ON LEFT FOOT.

EMPL HELPING CLEAN 3 SCRUBBER MIXING CHAMBER WHEN PIECE OF METAL FELL FROM THE NEXT LEVEL UP.30'. MAINTENANCE CREW WAS WORKING ON THE PLATFORM DIRECTLY ABOVE THE EMPL. THEY HAD REMOVED THE EXPANSION JOINT STRAPS & PLACED THEM ON THE LIP OF THE JOINT. EMPL WAS BEATING ON WALL OF MIXINGCHAMBER WHEN THE STRAP FELL, STRIKING EMPL ON THE HEAD.

EMPL MOVING SWITCH ON A 60 AMP FUSED DISCONNECT TO THE OFF POSITION -SWITCH FAILED AND SHORTED BLOWING DOOR OPEN AND BURNING EMPL ON FACE,NECK,AND RIGHT ARM.

THE EE WAS POSITIONING A HYDRAULIC JACK UNDER THE KILN WHEN THE JACK TURNED OVER AND CAUGHT HIS FINGER.

EMPLOYEE WAS PRYING CASTIBLE FROM OVERHEAD IN #3 KILN HE WAS STANDING DOWNHILL FROM MATERIAL WHEN A PIECE OF THE CASTIBLE FELL ON HIS RIGHT FOOT

THE EMPLOYEE HAD CHANGED A FUSE IN AN ELECTRICAL BOX. HE CLOSED THE DOOR AND THREW THE SWITCH AT WHICH TIME THE BREAKER SHORTED. FIRE ESCAPED PAST. THE EDGES OF THE DOOR BURNING BOTH ARMS AND FACE OF THE EMPLOYEE.

MOVING HYDRAULIC UNIT ON THE JOB.HAD THE HYD. UNIT JACKED UP WITH A JACK. WAS MOVING A TIMBER FROM UNDER THE UNIT AND IT SLIPPED OFF THE JACK. HYD. UNIT FELL ON RIGHT HAND INDEX FINGE AND MIDD LE FINGER OF RIGHT HAND LACERATIONS AND MASHED.NO BROKEN BONES.STITCHES.

EMPLOYEE SAID WAS LIFTING GRATES TO CHECK A NUMBER. OFF WORK BEGINING ON 5-26-92, AVAILABLE WORK TIME LOST 73 DAYS. REST OF TIME OFF WAS ON UNEMPLOYEMENT.

WHILE WALKING THRU THE PLANT THE EE SLIPPED IN SOME MUD TWISTING HIS LEFT KNEE.

WHILE CHECKING THE OPERATION OF THE KILN, A CINDER BLEW BACK FROM THE KILN INTO THE EMPLOYEE'S EYE. THE EMPLOYEE WAS WEARING SAFETY GLASSES AND A FACE SHIELD.

WHILE PICKING-UP A FOOT VALVE, THE EMPLOYEE PULLED HIS HAMSTRING.

EMPL SAID LIFTING GRATES TO CHECK A NUMBER.DIDNT SAY ANYTHING TO ANYONE UNTIL 3-12 WHEN EMPL TOLD MGR. OFF WORK TH & F BACK TO WORK MONDAY THEN SAW DR EXCUSED 3 DAYS THEN BACK TO WORK.

WHILE HELPING TO LIFT A GUARD THE EMPLOYEE PULLED A MUSCLE IN THE RT SIDE OF THE STOMACH

THE EMPLOYEE WAS SHOVELING DIRT FROM UNDER A CONVEYOR BELT WHEN HE STRAINED HIS BACK.

THE EMPLOYEE WAS LIFTING A STEEL PLATE WHEN HE STRAINED HIS BACK.

THE EMPLOYEE LOST HIS BALANCE WHILE STANDING ON A 2' X 4" CONCRETE WALL AND FELL, LANDING ON HIS FEET.

THE EMPLOYEE WAS CHANGING SKIRTS ON A CONVEYOR BELT WHEN SOME DIRT FELL OUT OF THE CHUTE AND ENTERED THE RIGHT EYE.

THE EMPLOYEE WAS HELPING CARRY AN H-BEAM FROM A CATWALK TO THE PLATFORM BELOW. THE OTHER EMPLOYEE LOST HIS GRIP ON THE BEAM & IT STARTED TO SLIP OFF THE CATWALK. THE INJURED EMPLOYEE CAUGHT TH E BEAM & HELPED LIT IT BACK TO THE PLATFORM, INJURING HIS RIGHT WRIST.

SM BURN ON R LEG NEAR ANKLE STRADDLING BEAM UP HIGH WELDING, THREW AWAY BURNED OUT SM PC WELDINGROD, IT LANDED AGAINST PANTS LEG AND INSIDE OF SHOE

WHILE TAKING A SAMPLE OF AGGREGATE FROM THE KILN BACKFIRED CAUSING THE EMPLOYEE TO JUMP BACK.THE EMPLOYEE STRUCK HIS LEG ON THE FOUNDATION OF THE FIRING HOOD.

THE EMPLOYEE WAS WELDING. HE STOPPED AND LIFTED HIS WELDING HELMET. AT THIS POINT A PIECE OF FLUX FROM THE WELDING ROD POPPED INTO HIS LEFT EYE.

WHILE ATTEMPTING TO START SHAKER SCREEN BY ANUALLY JUMPING ON SPRING EMPL SLIPPED & FELL CATCHING RIGHT HAND IN SPRING. THIS RESULTED IN FRACTURE OF RIGHT HAND.

WHILE HELPING TO LIFT SHEET OF FLAT METAL, THE METAL SLIPPED FROM THE INJURED PARTY'S HAND COMING IN CONTACT WITH HIS LEFT LEG RESULTING IN A CUT.

EMPL PUTTING CABLES BACK INTO TOOL BOX AND DIDNT GET FINGERS CLEAR OF BOX BEFORE LID CLOSED ON FINGER AND CUT FINGER TIP AND PART OF FINGERNAIL,RING FINGER-LEFT HAND.STITCHES TAKEN.

EMPLOYEE SLIPPED AND FELL BACKWARDS AND STRUCK LEFT SHOULDER ON STEEL RAIL.

WHILE OPERATING AN EXCAVATOR AT THE PLANT, A HYDRAULIC HOSE BURSTED CAUSING HYDRAULIC OIL TO BE SPRAYED IN THE DIRECTION OF THE CAB. THE SMALL WINDOW TO THE RIGHT OF THE OPERATOR WAS OPEN ALLO WING THE HYDRAULIC OIL TO MAKE CONTACT WITH THE OPERATOR'S FACE AND RIGHT EYE.

CONNECTING UNION HALVES TOGETHER HAND SLIPPED CAUSING HIM TO CUT HIS L ARM

WORKING ON INSTALLATION OF GRATING. GRATING WASNT WELDED YET,STEPPED ON GRATING AND FELL THROUGH.BROKE RIGHT ARM AND CRACKED HIP JOINT.

EMPLOYEE WAS WALKING ON #1 COOLER GRATE WHEN HE SLIPPED AND HIS LEG WENT THROUGH THE OPENING.HE HAD A CONTUSION ON RIGHT KNEE AND A FRICTION BURN ON HIS RIGHT ARM.

EMPLOYEE SLIPPED AND HIT HIS LEG AGAINST THE ANGLE IRON WHILE WORKING ON A CONE CRUSHER.

EE WAS LIFTING A SECTION OF PLASTIC PIPE TO MOVE IT AFTER TAKING SEVERAL STEPS EE COMPLAINED ABOUT A PAIN IN HIS LOWER BACK. THE WEIGHT OF THE MATERIAL WAS NOT MORE THAN EE SHOULD HAVE BEEN AB LE TO CARRY INCORRECT TWISTING OF THE EE S BODY WAS THE DIRECT CAUSING OF THE PAIN.

EMPLOYEE WAS USING A JACKHAMMER WHEN IT SLIPPED AND STRUCK HIS LEFT FOOT CUASING INJURY TO HIS 2ND AND 34D TOE. EMPLOYEE SUFFERED SOME SWELLING AND WAS SENT FOR MEDICAL HELP.

EMPL CHARGING BATTERY ON KILN #2 WHEN WIND BLEW DUST INTO EYE/.

EMPL WALKING ACROSS COMPANY PROPERTY TO LEAVE AFTER CHANGE OF SHIFT WHEN HE SLID ON SLIDER AND SPRAINED ANKLE.

EMPLOYEE WAS OPERATING JACK HAMMER IN KILN #3 WHEN HE BRACED HIMSELF AGAINST THE KILN WALL AND CUT HIS FINGER ON THE WALL.

EMPLOYEE WAS RODDING CLAY ON CONVEYOR BELT WHEN A PIECE CAME OUT OF HOPPER IN THE LOWER CLAY SHED AND HIT EMPLOYEE IN BACK OF NECK.

GOT DUST IN EYE WHILE WORKING

WIND BLOWING DUST IN R EYE

THE EMPLOYEE WAS TAKING A LINK OUT OF THE COAL DRAG CHAIN. HE SLIPPED AND THE CHAIN LINK FELL ON HIS LEFT HAND SECOND INDEX FINGER.

EMPLOYEE TURNED QUICKLY TO LOOK BEHIND HIM AND PULLED THE MUSCLE IN THE LEFT SIDE OF HIS NECK.

EMPLOYEE WAS TRYING TO UNSTOP THE HOPPER WHENHE LOST HIS BALANCE AND FELL BUMPING HIS ELBOW ON THE HOPPER.

EMPLOYEE WAS STEAM CLEANING CEMENT WHEN HE DIRECTED THE NOZZLE TOO CLOSE TO HIS LEG. HE SUFFERED MILD BURN FROM STEAM ON HIS RIGHT ANKLE.

EMPLOYEE WETTING DOWN THE LOAD OF LIGHTWEIGHT AGGREGATE ON IS TRUCK WHEN HE SLIPPED AND FELL FROM THE WASH RACK.

THE WIND WAS BLOWING HARD AND THE EMPLOYEE GOT DUST IN HIS EYE.THE DUST THEN IRRITATED.

EMPLOYEE WAS TAKING A SAMPLE OFF THE CONVEYOR BELT WHEN THE WIND BLEW DUST IN HIS RIGHT EYE.

EMPL WAS REMOVING SPROCKET FROM SHAFT WHEN SLIVER OF METAL STRUCK HIM IN ARM. HE WAS SENT FOR MEDICAL ATTENTION TO REMOVE PIECE OF METAL.

EMPL WAS USING SHOTGUN TO SHOOT RING OUT OF KILN WITHOUT NECESSARY EAR PROTECTION. HE SAID THAT HE WAS NOW HAVING DIFFICUTLY HEARING OUT OF LEFT EAR. HE WAS SET UP WITH APPOINTMENT TO HAVE HEA RING EVALUATED. MY 091890A300918901500070028121

EMPLOYEE WAS SHOVELING MATERIAL IN THE COOLER AREA OF KILN #1,2,3 WHEN HE STARTED EXPERIENCING PAINS IN HIS LEFT ARM AND CHEST. EMPLOYEE CLAIMS THAT HE BECAME OVERHEATED DUE TO THE WORK AND TE MPATURE.

EMPL INSTALLING SHAKER SCREEN,WIND BLEW SAND INEMPL RIGHT EYE.

EMPL DRIVING LOADER.WIND BLEW DUST INTO RIGHT EYE.

EMPL PULLING DOLLEY CONTAINED HEAVY EQUIP.THE EQUIP MOVED ON DOLLEY,FLIPPING DOLLEY AND STRIKING EMPL RIGHT FOOT.

EMPLWAS WALKING OVER PILE OF AGGREGATE WHEN HE SLIPPED ON LOOSE AGGRGAT & TWISTED LEFT FOOT.

EMPLOYEE SLIPPED WHILE REPAIRING THE CONVEYOR BELT AND REINJURED HIS LEFT KNEE. HE HAD INJURED HIS KNEE AT WORK 11-5-85.

THE EMPLOYEE WAS GETTING OFF A FRONT END LOADER AND SLIPPED OFF THE STEPS AND FELL TWISTING HIS KNEE.

EMPL WAS WORKING INSIDE #3 SCRUBBER CLEANING OUT MUD & HARD MINERAL DEPOSIT BUILD UP OFF WALLS. HE WAS USING PICK TO PRY MINERAL DEPOSIT BUILD UP IT BROKE LOOSE & FELL ON RT ANKLE & BRUISED IT .

GOT SOME DUST IN RIGHT EYE AND SCRATCHED IT.NOT WEARING SAFETY GLASSES.

THE EMPLOYEE WAS REPLACING U-BELT'S ON THE CONVEYOR UNDER THE PRIMARY CLAY CRUSHER. NO ONE HAD PULLEY THE SAFETY SWITCH, THE MOTOR WAS STILL RUNNING. THE EMPLOYEE TRIED TO REPLACE THE BELT'S RESULTING IN CRAKING HIS THUMB.

THE EMPLOYEE WAS TIGHTENING A BOLT ON THE SCRUBBER PUMP. HIS WRENCH SLIPPED RESULTING IN A CUT TO HIS RIGHT FOREARM.

TRACTOR DIDD NOT GO INTO REVERSE SLIPPED FORWARD HITTING AND CUTTING HAND BRUISING HIS HIP

EMPLOYEE WAS CLIMBING TO GREASE SCREEN DECK AND LOST BALANCE FALLING AND BREAKING HIS TOOTH.

I NAME WAS COMING DOWN TO OFFICE TO FILE OUT DAILY REPORT I NAME PUT LEFT FOOT UPON SIDE WALK & WHEN HE WENT TO LIFT RT LEG IT WAS CAUGHT IN MUD CAUSING IT TO PULL & POP HIS KNEE

I.NAME UNCOUPLING RAIL CAR STEPPED BETWEEN PULL -CABLE AND RAIL CAR.LEGS BECAME CAUGHT BETWEEN THE TWO.

EMPL WAS CHANGING OUT FOOTVALVE ON #3 SCRUBBER PUMP WAS BENT OVER FOOT VALVE WHILE SCREENING IT OFF. HE LOWER IT 8" PIPE NIPPLE CAME UP & HIT HIM IN MOUTH. IT SPLIT LOWER LIP & LOOSENED 1 FRON T TOOTH.

I WAS CUTTING A PIECE OF PLATE WITH THE TORCH THE TORCH WAS NOT BURNING CORRECT IT TRIED TO CORRECT AND TORCH BLEW UP

WAS LAYING OUT STEEL TO BE WELDED, GOT A SLIVER OF STEEL IN FINGER.

EMPLOYEE WAS WELDING NEXT TO CO WORKER. WAS WELDING ON MULTI-CLONE AND SHE RAISED HER HOOD, THE TORCH FLASH FROM THE OTHER WELDER BURNED HER EYE.

EMPL WAS WELDING ON CONVEYOR FOR COOLER. LENS ON WLEDING HOOD & GASKET MUST HAVE HAD SMALL CRACK WHICH CAUSED FLASH FROM TORCH TO BURN EYES. DR PRESCRIBED MEDICATION FOR EYES.

EMPL WAS GETTING PAIR OF CLEAR LENS OUT OF GANG BOX. LID FELL BACK ON HEAD & SCREW IN TOP OF LID LEFT PUNCTURE WOUND TO TOP OF HEAD. BUTTERFLY STITCH USED TO CLOSE WOUND. OFF ALL THAT AFTERNOO N FROM WORK BUT RETURNED TO WORK AT USUSAL WORKTTIME NEXT MORNING.

EMPLOYEE WAS CHANGING A SCREEN PANEL IN THE CRUSHING DEPARTMENT WHEN HE STRUCK HIS FOOT AGAINST THE WALL OF THE SCREEN DECK.

WAS WELDING & WORKING AT COAL MILL,TINY SLIVER OF RUST POPPED INTO EYE.CONTINUED TO WORK EVERY DAY BUT EYE STILL BOTHERING HIM ON 7-18 AND WENT TO SEE EYE DR WHO DIAG PIECE OF RUST -GOT IT OUT OF RUST OR FOREIGN OBJECT GOT IT OUT.

EMP SAID SMOKE STUFF BLOWING OUT OF SCRUBBER WHILE HE WAS SITTING IN CRANE AS OPERATOR WORKING ON INLET HOOD CAUSED RASH ON ARM. HE WENT SENT TO SEE DR WHO GAVE HIM PRESCRIPTION FOR TOPICORT C REAM TO USE ON RASH.

MASHED LEFT RING FINGER. CONTUSION AND ABRASION OF FINGER FROM BOARD FALLING ON FINGER WHILE THROWING TRASH OUT OF KILN ON JOB.

WAS WELDING & WHEN RAISED HOOD TO CHANGE OUT WELDING RODS FLUX POPPED & HIT IN LEFT EYE.

WAS WLEDING ON CONVEYOR.

WAS WELDING & WHEN RAISED HOOD TO CHANGE OUT WELDING RODS FLASH BURN TO EYE.

EMPL WEAS GRINDING PIECE OF STEL FOR SCRUBBER WITH GRINDING WHEEL & TINY CHIP OF STEEL GOT INTO EYE.

WAS WLEDING & FITTING PIECES ON INLET HOOD.

WIND WAS BLOWING VERY HARD AND BLEW DUST SAND,AGGREGATE PARTICLES INTO EYE CAUSING CORNEAL ABRASION OF LEFT EYE.SAFETY GLASSES AND GOGGLES WERE NO HELP,FOR THIS.

THE ROTARY KILN WAS HOT WHEN THE EMPL SLIPPED AND FELL AGAINST THE KILN

EMPL WAS UNHOOKING WELDING TRAILER AND AS IT STARTED TO GO BACKWARDS OFF THE JACK HE GRABBED AT THE TRAILER TONGUE TO KEEP IT FORM FALLING AND THE MOTION OF TRYING TO CATCH IT AND THE WEIGHT O F THE TONGUE JERKED AND PULLED LIGAMENTS IN LOWER BACK NO LOST WORKTIME EXCEPT TO GOT SEE DR ON 5/3/89

KILN HELPER WAS CHECKING TRUNION ROLLERS.THE WATER ON THE ROLLERS WAS HOT AND THE HOSE CAME OFF THE ROLLER AND THE WATER SPLASHED ON EMPLOYEE.

EMPL WAS USING GRINDING WHELL TO MAKE PART NEEDED ON KILN CONSTRUCTION GRINDING WHEEL CAUGHT SHIRT FRONT AND WHEEL WENT UP ABDOMAN AND AROUND UNDERNEATH L BREAST CAUSING BRUISES

WAS WELDING & FLASH BURNED EYE. SAID DIDN'T BOTHER HIM TOO MUCH UNTIL THAT NIGHT & HE WENT TO EM ROOM AT HOSP.

RAISED SHIELD ON HIS WELDING HELMET TO CHANGE OUT WELDING RODS AND FLASH FROM ANOTHERS WELDING TORCH BURNED EYES

EMPL RAISED SHIELD ON HIS WELDING HOOD TO CHANGE OUT HIS WELDING RODS AND FLASH FROM NEARBY WELDERS TORCH BURNED EYES

WHEN RAISED SHIELD ON WELDING HOOD TO CHANGE OUT RODS FLASH FROM ANOTHER WELDERS TORCH BURNED EYE.

CHIPPING SLAG DURING WELDING AND SMALL CHIP OF SLAG POPPED INTO RIGHT EYE.

EMPL MOVING QUARTER INCH METAL PLATE -500 LBS-INTO PLACE TO WELD ON SIDE OF COOLER AND DROPPED IT ON LEFT FOOT RESULTING IN BREAKING /DISPLACING BIG TOE AND ONE NEXT TO IT.DR PUT PIN IN BIG TO E.

EMPL WELDING,TURNED AROUND AND LIGHT FLASH FROM TORCH BURNED EYES.

EMPL BEATING ANGLE IRON OFF FORMS JUST SET.WHEN KILN SECTION WAS TURNED,IRON HAD GOTTEN HUNG IN A FORM AND HAD TO BE GOTTEN OUT.IRON PIN STRUCK SIDE OF EMPL HARD HAT...NEXT DAY SUDDENLY HAD BA D HEADACHE,DIZZINESS & KNOT ON SIDE OF HEAD.RESULT FROM DR REPORT WAS CONTUSION TO SCALP.

THE EMPLOYEE HAD WELDED A N EYE BOLT TO THE KILN BURNER PIPE.WHILE HOISTING THE PIPE BACK,THE EYE BOLT BROKE AND HIT THE EMPLOYEE ON THE LEFT SHOULDER CAUSING A BRUISE.

PICKED UP & LIFTED PIECE OF STEEL PLATE FROM GROUND & PUT IT ON A TABLE TO BE CUT IN DOING SO RESULTED IN ACUTE LUMBO-SACRAL MUSCLE SPRAIN & SPASMS SAW DR ON 22ND 23RD & WAS RELEASED AS PHYSIC ALLY ABLE TO RETURN TO WORK ON FEB 24TH

EMPLOYEE WAS BURNING, CUTTING PIPE OVERHEAD AND SLAG FELL INTO GLOVE AND BURNED TOP LAYER SKIN ON LEFT ARM ABOVE WRIST. GOT INFECTED OVER WEEKEND. SAW DR MON. 2-6-89 AND EACH DAY SINCE TO DATE 2-9-89.

EMPL WAS USING JACKHAMMER & SHOVELING OLD CASTABLE FROM #2 KILN TO CLEAN KILN FOR REPOURING OF NEW CASTABLE.

EMPLOYEE WAS MOVING LADDER TO ANOTHER WORK AREA WHEN HE PULLED A MUSCLE IN HIS LOWER BACK.

NO LOST WORK TIME PICKED ;UP MACHINERY PART WITH LIFT OF CRANE AND LOWERED IT NEARLY TO GROUND GOT OFF CRANE AND WAS SWINGING THE PART ON LIFT AROUND BY HAND PART STILL ATTACHED TO CRANE LIFT AND HIS LEFT FOOT GOT BETWEEN THE SWINGING PART AND GROUND MASHED THIRD TOE TOOK SKIN OFF AND LATER IN WEEK INFECTION.

FIVE MEN PICKED UP A 40FT.PIECE OF ANGLE IRON & AS THEY WERE TURNING IT AROUND THIS ONE MAN SAID HE HURT HIS BACK STRAIN FROM BODILY MOTION OF TURNING THE IRON PIECE AROUND ONCE THEY ALL HAD LIFTED IT SO HE LATER REPORTED IT ON 110188

EMPLOYEE WAS OPENING DOOR OF FRONT END LOADER TO GET OUT AND HIS HAND SLIPPED OFF THE DOOR HANDLE AND EMPLOYEE BUMPED HIS ELBOW ON THE CAB DOOR AND FRACTURED BONE

EMPLOYEE WAS REMOVING REFRACTORY BRICK FROM ROTARY KILN. HE WALKED UNDER THEM AS THEY WERE FALLING.

EMPLOYEE WAS HELPING TO REPLACE THE CUTTING EDGE ON A FRONT-END LOADER BUCKET WHEN HE PICKED UP ONE END HE DROPPED IT ON HIS FOOT RESULTING IN A BROKEN TOE

EMP WAS CLEANIN1 OUT CHUTE AROUND SCREEN WITH A METAL ROD WHEN THE ROD FELL INTO SCREEN. THE SCREEN THREW THE ROD OUT HITTING EMP IN MOUTH AREA

EMPLOYEE WAS WO9KING IN COOLER PIT AREA WHEN HOT FEED DROPPED FROM THE KILN INTO THE COOLER PIT AND SPLASHED HOT WATER ON EMPLOYEES ARM LEGS AND FACE

THE EMPLOYEE WA8 LIFTING AS MALL AUGER SCREW CONVEYOR, RESULTING IN STRAINING, CAUSING A HERNIA.

EE FRACUTRED HIS FINGER WHILE BEATING ON A CHUTE DOOR WITH A PRY BAR. THE BAR SLIPPED & HE HIT HIS HAND ONT HE SIDE OF THE CHUTE.

INJURED FELL OFF CRUSHER PLATFORM WHILE CLEANING UP AND SUFFERED ABRASIONS ON HEAD.

INJURED WAS REACHING FOR PRY BAR AND HIT HIS THUMB ON METAL COVER OVER WALL PLUG BOX

UNLOADING BEARING FROM TRUCK WHEN FINGER CAUGHT UNDER LOADED PALLET CAUSING IT TO GET MASHED.

LOADER BACKED INTO FORKLIFT AND INJ WAS PINCHED BETWEEN THE 2 MACHINES.