Mesa Plant Metal/Non-Metal

While changing bucket teeth on loader, tooth fragment broke loose and went into left thigh.

Helping change crusher liner holding onto tag line and stepped between crusher and catwalk area. **Employee reported to plant manager and they determined no injury. On 7/17/07 the employee's elbow was swollen & he was sent to the clinic and fluid was removed.**

Jumped off of conveyor - inguinal hernia on right side.

While working on chute liner employee holding steel plate lost his grip and plate landed on employee's foot, leaving a sliver of steel in his foot.

Quality control employee emptying sieve screens and a small particle of rock or dust bounced into his eye under his safety glasses.

REMOVING DEAD BED FROM UNDER JAW BELT, THUMB WAS PINCHED BETWEEN DEAD BED AND JAW FRAME.

CLOSING UPPER WINDOW ON RENTED CRANE, WHEN THE WINDOW SLIPPED & SLAMMED SHUT ON RIGHT THUMB. RT HAND 3RD FINGER CRUSHED & LACERATED.

EE WAS CLEANING GRIZZLY ON JAW FEEDER WITH A 8 LB HAMMER. THE HAMMER CAME IN CONTACT WITH THE UPPER BEAM SUPPORT AND STRUCK EE ON LEFT SIDE OF HIS HEAD.

WHILE HELPING INSTALL ROLLERS IN A SCREEN THE ROLLER SLIPPED OUT OF ITS KEEPER. THE EMPLOYEE REACHED TO CATCH IT AND STRAINED THE MUSCLES IN HIS BACK.

WHILE REPLACING BELT AND TAIL PULLEY ON MP02 CONVEYOR. THE EE WAS HELPING LEFT THE TAIL PULLEY INTO PLACE WHEN THE TAIL PULLEY SLIPPED AND CAUGHT HIS HAND PUSHING IT AGAINST THE FRAME.

WHILE TIGHTENING DRILL BIT WITH SCREW DRIVERS RIGHT HAND SLIPPED AND CUT LITTLE FINGER ON DRILL BIT. REQUIRED C9 STITCHES TO CHOSE WOUND.

WHILE REMOVING A RIPPER TOOTH FROM A DOZER EE HIT TOP OF TOOTH WITH A HAMMER CAUSING A PIECE OF METAL TO CHIP & ENTER THE THIGHT OF THE RIGHT LEG

WHILE CLENAING RAP DRIVE BREAK OVER PULLEY WITH SCRAPER BAR, BAR GOT CAUGHT RIGHT HAND TO BE PULLED INWARD.

WHEN STEPPING OFF LADDER ONTO GROUND EMP TURNED TOO SOON AND TWISTED LOWER BACK.

AFTER CONE CRUSHER ADJUSTMENT WAS COMPLETED THE MACHINERY WAS PUT INTO A SINGLE PHASE STARTUP. EQUIP WAS THEN TURNED OFF, ELECTRICAL PANEL WAS OPENED ON BACKSIDE WITH DISCONNECT STILL ENERGIZE D. KNIFE EDGE ON DISCONNECT WAS PUSHED IN WITH A SLEDGE HAMMER. THE HAMMER TOUCHED TWO PHASES OF 480 VOLTS TOGETHER RESULTING IN FLAMES TOWARD EE. ELECT. PANEL WAS DESTROYED.

FRONT END LOADER RAN OUT OF FUEL. LOADER LOST POWER TO ALL CONTROLS. ROLLED BACKWARDS AND OFF A 30 TO 40 FT. EMBANKMENT.

WHILE CLEANING A FAN FEEDER WITH HAND PICK.

DRIVER SLIPPED ON BERM OF BANK AND FELL 25'TO OPEN PIT AREA.RESULTED IN VARIOUS PUNCTURE WOUNDS TO HEAD,ARMS AND POSSIBLE NECK & BACK SPRAIN.

WAS USING PRY BAR TO CLEAN DIRT AROUND TAIL PULLEY ON CONVEYOR.BAR GOT CAUGHT IN TAIL PULLEY AND PINCHED FINGER AT CONVEYOR FRAME.

WHILE INSTALLING WEDGES IN CRUSHER CONE HIT LEFT ARM ON BRACE.

FOOT SLIPPED ON DOZER TRACK FELL ON PUSH ARM OF DOZER AIR WRNECH ON GROUND.

CUTTING STEEL- BEAM FELL- RIGHT FOOT.

TURNING U-BELT 6Y HAND TO CLEAR TAILPULLEY WHEN A ROCK WENT PAST CENTER BELT ROLL ABOUT 4" PINCHING FINGER.

REPLACING JAW P5ATE, HE WAS HOLDING IT IN PLACE WITH FOOT, PLATE SHIFTED BACK BENDING FOOT BACK.

LOST FOOTING WH3LE DIGGING OUT HOPPER.FELL AND HIT LEFT KNEE ON STEEL RAIL.

DUST IN EYE FRO4 WORKING ON PUG MILL AT ASPHALT PLANT.

REMOVING BOLTS 0ROM A VALVE, WRENCH SLIPPED, BUMPED ELBOW.

EMPLOYEE FELL O0F BELT ONTO SCREEN BELOW.

COOLANT FROM RA8IATOR BURNED HIS STOMACH.

LIFTING A CONVE2OR ROLLER APPROX 200 LBS PULLED MUSCLE IN BACK

WORKING AT CRU8HER PLANT AROUND CONVEYOR BELT WAS STRUCK BY BOULDER IN HEAD AT HIGH RATE OF SPEED KNOCKING HARD HELMET OFF AND CAUSING ABRASION TO HEAD.

CHAIN BROKE HOLDING JAW-MOVEABLE SIDE- MOVED BACK & HIT HIS FINGERS.

CHAIN BROKE THAT HELD JAW CRUSHER OPEN FOR REPAIR PITMAN HIT I.NAME IN THE HEAD & BACK.

PUTTING JAW CRUSHER TOGETHER PIECE OF METAL FELL AND HIT ARM AND HAND

COMING DOWN LADDER WRONG WAY AND HIT HEAD ON CAT WALK.

OPERATOR CLIMBING DOWN LADDER STEPS ROCK HIT ANOTHER ROCK ON FEEDER AND RIOCHETTED OFF FEEDER HITTING OPERATOR IN LOWER BACK.