Warrior Preparation Plant: 2 recorded fatalities Coal

Contractor was hauling soil from the back side of gob hill. As EE was returning for another load, EE heard a pop in the engine and started smelling and seeing smoke in the cab. As EE stopped to make a check, the truck was on fire. EE tried to put the fire out with a fire extinguisher EE had along with another one from another truck. Fire Dept was called. No injuries.

Employee was putting bolts in a piece of rubber on the vibrator lip when the walk board broke causing EE to fall into the chute. EE hit head shoulder and hip on the metal sides. EE had 6 staples in head.

Employee was operating a dozer while loading a train; a chute stopped up and was not feeding coal. After about 20 minutes of it not feeding the operator's were told to stay off of the feeder. The employee drove his dozer to close as he was feeding the main feeder and the dozer fell in bridge area of the feeder. The employee was not entrapped and he got out on his own.

EE was in the process of cutting a steel cable that was tangled on the D8N dozer at the trash dump. As ee lit the torch the first time it went out. As he was relighting it a buzzing nose and a ignition happened. This caused burns to the left elbow and low arm.

Magnet on raw coal B VIB, The hook broke and struck ee in the back of the head, also in the middle of his back.

This contractor was lifting a pipe up about 4ft to put it into place. The pipe weight was 140. The flange end had a sharp edge that wasn't noticed. Another EE was helping do this job.

After employee had locked & tagged the belt out for repairs he decided to stay and help change the roller. This was a 54 in. troughing roller. While putting the roller in position to stand it up the roller slipped and mashed his left thumb between the belt frame and roller. 10 stitches to injury.

Employee was trying to break loose a bolt with a wrench, in doing so the wrench slipped and hit him in the mouth, cutting his bottom lip and chipping his tooth.

While attempting to stop a leak on the refuse box, two workers were going to apply a patch by using a piece of belting and metal. Co-worker climbed up a permanent ladder and injured employee grabbed the closest ladder, the upper part of an extension ladder. As he climbed up the ladder, it slipped causing him to fall.

EE was trying to dislodge a screwdriver from a shaker in the prep plant. EE missed hitting the screwdriver and hit his hand. This caused him to have 5 stitches.

EE was replacing 200 amp fuse for the deep well Pump "D". While installing a fuse his right thumb made contact with the voltage barrier causing a laceration to the pad of right thumb.

EE was cutting a piece of bucker rubber for repair on the vibrator. While sitting down, he was holding the rubber in his left hand and in his right hand he was using a belt knife to cut the rubber with. After cutting through the hard surface, he entered the soft spot part with extra force, causing the knife to slip and cut his upper leg.

Pressure washer had quit. Worker climbed into back of truck, fixed the problem by securing a wire, turned around & fell off the truck. Initially, this was not a reportable accident because worker did not seek med. treatment & no time was lost. Worker did not seek med attn until 9/14/10 & was placed on restricted duty. Effective 9/20/10, he was off work completely.

Employee was in the coal loadout tunnel watching the belts while the train was being loaded. He noticed a piece of coal was stuck in the skirt rubber on the south side of the belt (main). He removed the piece of coal and the conveyor belt caught his right hand and arm

EE was grinding on a 988 loader bucket, as he was grinding down a vertical position, sparks were going down and to his right. Foreign material entered his left eye. Safety glasses with side shields were worn at the time of the injury.

Employee was grinding on a dozer blade. As he was grinding he felt like something was in his right eye. He finished the shift then he went to the nurses station & had it washed out. He then had to to to the Dr. to have a foreign object removed from his eye. Safety glasses with side shields were worn at the time of the accident.

EE was removing a chute from the #2 belt drive stand. On his last attempt to adjust the chain rigging, he stepped in a spot where a roller bearing had been removed, stepped in grease and his left foot slipped backwards and he fell through an opening in the floor, 12 ft to the ground. He started missing work 5-22-08.

Employee was standing on the North winch table hooking up ground for the welder. After hooking the ground up, he went to step off of the table and lost his footing, landing on uneven ground on his right leg. He started missing work 3/16/08. He will be off 4 months (ACL).

EE was in the process of taking out the old belt scales at the loadout tunnel. As he was cutting the last leg, which was tied off by the winch cable to the boom truck, the metal kicked back, causing his finger to get pinched between the I beam.

As ee was drilling a borehole into the old works, he stepped off the drill platform and twisted his right knee. 7/13/07 was his first day to miss work.

EE was in the man lift on the west side of the gob belt bottom counter weight roller. He put his left hand on the roller bearing to see if it was heating up and an eye welded to the other rollers came around the inside of the bearing and caught his index finger on the left hand.

Employee was trying to open the flop doors at the syn-fuel discharge belt. As he was pushing the handle over, something gave way and broke. This caused the handle to go forward and away rapidly. He held onto the handle causing him to spin around and fall backwards approx 12 feet to the concrete pad.

While moving a 1" thick piece of plate metal app 8"x33"x1" the plate was being pulled off the bed of the welding truck, it slipped out of ee's hand creating a whoosing effect stirring up rust. dust and possibly weld slag. He felt something in his right eye immediately.

Ee was standing by the core drill assisting the e-logger on the report sheet when the wind started blowing causing debris to go into the eye.

BANDING A TEMPORARY PATCH ON A PIPE. EE STARTED TO LOAD THE BANDING TOOL WHEN HE DISCOVERED AN OLD PIECE OF BAND IN THE TOOL. WHEN HE WAS HOLDING THE TOOL WITH HIS LEFT HAND & USING CHANNELLOCK PLIERS WITH HIS RIGHT HAND, THE OLD PIECE CAME OUT FASTER THAN EXPECTED, CUTTING HIS KNUCKLE ON LEFT THUMB - 3" IN LENGTH.

EMPLOYEE WAS IN THE PROCESS OF CHANGING THE DRILL BIT ON THE DK40 DRILL, AS HE WAS LIFTING THE BIT HE SLIPPED & TWISTED HIS BACK.

EE WAS OPERATING A D9L DOZER ON THE RAW COAL STOCK PILE, WEATHER FOGGY. WHEN HE STARTED TO PUSH THE COAL, HE TRIED TO ADJUST THE C.B. RADIO HE NOTED HE HAD GONE TOO FAR ON THE PILE. HE TRIED TO PUT THE DOZER IN REVERSE GEAR, BUT COULD NOT, THE SEAT BELT WAS IN BACK OF THE SHIFTER. HE WAS NOT WEARING THE SEAT BELT.

WHILE TRYING TO TURN THE NEW GOB CHUTE THAT HE WAS FABRICATING, EE WAS USING A STEERING LOADER TO PICK IT UP & USE A PRY BAR TO TURN IT OVER. AS HE WAS TURNING IT OVER, THE CHUTE SLIPPED CAUSING THE BAR TO PIN AGAINST THE FLOOR, WITH HIS FOOT IN BETWEEN.

EMPLOYEE WAS OPENING ACCESS DOOR TO THE #5 COUPLING AT THE SLOPE HEND DRIVE, THE DOOR BECAME OVER BALANCED & STARTED TO FALL AWAY FROM EE. HE REACHED OUT WITH HIS LEFT HAND TO CATCH THE DOOR & HIS THIRD FINGER GOT MASHED BETWEEN DOOR & THE SPEED REDUCER.

EE WAS HELPING WORK IN THE WASH PLANT TAKING DOWN A CHUTE. THE CHUTE WAS RESTING ON THE FLOOR AND TOP OF NEXT FLOOR. A LADDER WAS NEXT TO THE CHUTE WHEN EE WAS MOVING THE LADDER IT CAME OVER HITTING EE IN THE RIGHT SHOULDER.

EE WAS GETTING READY TO OPERATE THE FRONT END LOADER, HE STARTED TO GET ON THE MACHINE, HE WAS ON THE 3RD STEP AND HE SLIPPED OFF, FALLING TO THE GROUND.

STEEL PIECES WERE STANDING IN RACK WHEN ONE FELLOVER STRIKING VICTIM IN HEAD 5 OR 6 SUTURES

EMPLOYEE WAS ALIGNING A BELT ROLLER WHEN HE HIT HIS HAND WITH A HAMMER.

EE WAS REPAIRING A DRYER BASKET IN THE PREP PLANT. WHILE REMOVING A METAL BOLTY WITH A HAMMER & CHISEL, THE CHISEL SLIPPED AND HIT HIM IN HIS EYE. SAFTETY EQUIPMENT WAS PROVIDED BY THE EMPLOYE R (SAFETY GLASSES). THE EE STATED THAT HE REMOVED THEM BECXAUSE THEY WERE FOGGIN UP.

EE WAS LEAVING LUNCH AREA IN THE SHOP. HE OPENEED THE DOOR TO THE OUTSIDE AND THE WIND CAUGHT THE DOOR AND BLEW THE DLOOR BACK TOWARD HIM. HE RAISED HIS LEFT HAND TO STOP THE DOOR AND HIS HAND BROKE THE GLASS IN THE DOOR. THE BROKEN GLASS CUT HIS LEFT FOREARM.

THE EE WAS DRILLING HOLES IN A CONCRETE BLOCK WHILE STANDING ON A 6' LADDER. THE LADDER COLLAPSED CAUSING THE EE TO FALL ON HIS LEFT FOOT & ANKLE.

GPF-OCCUPATIONAL HEARING LOSS ALLEGED.

EE WAS REMOVING AN INTAKE MANIFOLD FROM A V-8 ENGINE AT A LOCATION OFF THE WARRIOR COAL MINING PERMIT. THE INTAKE MANIFOLD FELL STRIKING THE EE'S LEFT FOOT BEHIND THE STEEL TOE.

EE WAS OPERATING A CRANE AND HAD FINISHED LIFTING A PUMP AT AN OFFSITE AREA. WHILE LOADING THE CRANE PADS ON THE DECK OF THE CRANE HE CAUGHT HIS FINGER BETWEEN THE DECK AND THE PAD. THIS CAUSED A LACERATION OF HIS 3RD FINGER ON HIS LIEFT HAND

THE EE WAS IN THE PROCESS OF CHANGING THE OPERATORS SIDE MIRROR WHEN HE SLIPPED FROM THE RUNNING BOARD AND TWISTED HIS LEFT ANKLE. IT WAS RAINING AND THIS CONTRIBUTED TO THIS ACCIDENT.

THE EMPLOYEE (TRUCK DRIVER) WAS IN THE PROCESS OF RETRACTING THE TARP ON A TRACTOR BED USING A HAND CRANK AT SHOULDER LEVEL WITH HIS LEFT HAND.THE EMPLOYEE FELT A STRAIN IN HIS LEFT SHOULDER.

EE WAS REPLACING BRAKES ON A JEEP WHEN HIS HAND SLIPPED FROM THE BRAKE DRUM, CUTTING HIS LEFT THUMB ON A BRAKE SHOE.

EMPLOYEE SAID HE STRAINED BACK ON 2-13-96, WAS REPORTED TO EMPLOYER ON 2-19-96. EMPLOYEE WENT TOA DR ON 2-17-96. EMPLOYEE WAS LIFTING A BIT BOX AND STRAINED BACK.

EE WAS MOVING A SHEET OF 4'X8' PLYWOOD FOR SHILVING WHILE LIFTING PLYWOOD THE EE FELT PAIN IN HIS RIGHT HAND. ON 11-3-95 EE WENT TO SEE A DR.

ACCIDENT WAS NOT REPORTED UNTIL 10-12-95 BY EMPLOYEE. EMPLOYEE WAS MOVING PLASTIC WATER PIPE AND STRAINED LEFT BICEP MUSCLE.

EMPLOYEE WAS CHANGING THE SCREENS ON A VIBRATOR IN THE PREP PLANT. WHILE REMOVING A SCREEN THE WEIGHT SHIFTED PINNING HIS RIGHT LEG(ANKLE) BETWEEN THE SCREEN AND VIBRATOR.

THE EE STEPPED DOWN OFF OF A CONCRETE LANDING ONTO THE GROUND AND ON A LUMP OF COAL. THE TWISTING MOTION CAUSED A STRAIN ON HIS RIGHT FOOT AND A HAIRLINE FRACTURE.

INJURED WAS WORKING ON A METAL HOPPER WHEN HE CUT HIS RIGHT HAND ON A SHARP METAL.

THE EMPLOYEE WAS WALKING FROMTHE LOADOUT AREA TO THE LOADOUT TUNNEL A GUST OF WIND BLEW DEBRIS INTO HIS LEFT EYE THIS CAUSED AN ABRASION TO HIS LEFT EYE

EE CLOSING DOORS ON TRAIN CAR ANOTHER EE CLOSED DOOR ON VICTIM S FINGER.

THE EE WAS CUTTING WORN MATERIAL FROM THE BELT ON THE CONVEYOR SYSTEM. THE BELT KNIFE SLIPPED AND CUT HIS FINGER ON HIS LEFT HAND.

EE WAS MOUNTING A PIECE OF HEAVY EQUIPEMTN AND TORE LIGAMENTS IN RIGHT LEG (KNEE).

THE EMPLOYEE WAS CHECKING THE OIL ON A FRONT END LOADER WHEN THE WIND BLEW A PIECE OF COAL OR METAL INTO THE LEFT CORNER OF HIS RT EYE

ON 4-18-94 THE EMPLOYEE WAS USING A CUTTING TORCH TO CUT A PIECE OF METAL. A HOT PIECE OF METAL FELL INTO HIS LEFT BOOT CAUSING A BURN ON HIS LEFT ANKLE. THE EMPLOYEE DID NOT GO TO SEE A DOCTO R UNTIL 5-6-94. THIS ACCIDENT WAS AT FIRST FIRST AID ONLY. NOW IT IS A REPORTABLE ACCIDENT.

THE EE WAS MOVING METAL DEBRIS FROM THE SHOP AREA TOO ANOTHER LOCATION WHILE TRAMMING THE LOADER 988 CAT A GEAR SPROCKET FELL OFF THE BUCKET. THE EE PHYSICALLY LIFTED THE SPROCKET ONTO THE BUC KET. THE EE CAUGHT HIS THIRD FINGER OF HIS LEFT HAND BETWEEN THE GREAR AND A WOODEN PALATTE.

THE EMPLYEE WAS WELDING ANGLE IRON ON A METAL FRAME WHEN THE WELD BROKE & THE ANGLE IRON STRUCK HIS RT LEG THIS ACCIDENT OCCURRED ON 04-12-94 & AT THE TIKME WAS NOT A REPORTABLE INJURY ON 04-2 5-94 THE EMPLOYEE STATED HIS RT LEG WAS HURTING& WENT TO SEE A PHYSICIAN THE EMPLOYEE RECEIVED MEDS XRAYS THIS ACCIDENT IS NOW REPORTABLE

THE EMPLOYEE WAS CLEANING THE RUST OFF OF METAL GOB BUCKETS IN THE PREPARATION PLANT. HE WAS USING A METAL SCRAPER AND WIRE BRUSH TO REMOVE THE RUST. THE EMPLOYEE STATED HE WAS WEARING SAFETY GOGGLES, BUT LATER THAT NIGHT 3-19-94 HIS EYE BEGAN TO HURT. ON 3-20-94 THE EMPLOYEE WENT TO THE EMERGENCY ROOM AND HAD A SMALL PIECE OF METAL REMOVED.

THE EMPLOYEE WAS AT THE REFUELING STATION & HAD STARTED TO SERVICE A ROAD GRADER. THE EMPLOYEE LOST HIS FOOTING, SLIPPED & FELL FROM THE ROAD GRADER TO THE GROUND. THE EMPLOYEE TRIED TO BREAK HIS FALL WITH HIS RIGHT ARM & HAND. THE DAMAGE FROM THE ACCIDENT WAS A BROKEN ARM (RIGHT). EMPLOYEE FELL APPROX. 6'.

THE EMPLOYEE WAS MOVING WOODEN CRATES & CAUGHT HIS LEFT PALM ON A NAIL.

ON 03-18-93 EE WAS JUMP STARTING A PICKUP TRUCK WHEN THE TRUCK ROLLED BACK & PINNED HIS LEFT LEG TO ANOTHER PICKUP EE RECOMMEND HE GO TO SEE A PHYSICIAN BUT EE WAITED UNTIL 03-24-93 TO GO

EMPLOYEE WAS PICKING UP HANDTOOLS TO LOAD ON BACK OF TRUCK. EMPLOYEE SWUNG TO SIDE TO SET TOOLS DOWN, TWISTED BODY.

UNLOADING MINE PARTS OBJECT SLIPPED WHEN VICTIM GRABBED OBJECT IT MASHED LEFT INDEX AND LEFT MIDDLE FINGER.

THE ACCIDENT OCCURED WHEN THE EMPLOYEE STEPPED OFF A TRAIN CAR AND TWISTED HIS ANKLE. THE DIRECT CAUSE OF THE ACCIDENT WAS SLIPPING ON FROZEN GROUND WITHOUT A PROPER HAND HOLD ON TEH RAILROAD CAR. WARRIOR COAL MINING CO WAS INFORMED THAT THIS IS A REPORTABLE ACCIDENT BY BLUE GRASS LAD ON 1-22-93. THE EMPLOYEE OF BLUE GRASS LAB WAS SAMPLING AT THE TIME OF THE ACCIDENT.

EMPLOYEE STRAINED LEFT HAND PULLY ON EQUIPMENT CONTROLS. EMPLOYEE VISTED PHYSIAN AT LATER ATE. 2-12-92 WHERE AS MEDICATION WAS PRESCRIBED.

EMPLOYEE STUMBLED AND FELL BACK ONTO A PIECE OF METAL WHICH PUNCTURED HIS LEFT ELBOW.

54730WORKING ON A REPAIR CREW MVOING A TAIL SHAFT. THE CHAIN BROKE OR SLIPPED CRUSHING LEFT THUMB.

EMPLOYEE WHILE REMOVING THE STEERING MECHANISM ON A 988A CAT LOADER MASHED HIS MIDDLE FINGER RT HAND

THE EMPL WAS LOADING EMPTY OXYGEN CYLINDERS INA TRUCK AND LOST GRIP ON THE CYLINDER.CAUGHT 1ST AND 2ND FINGER BETWEEN THE BOTTOM OF THE CYLINDER AND THE LIP OF THE TRUCK.WORKED 5-2 /5-4. WENT TO DR 5-5-92.

EE WAS PICKING GOB AT THE PREP PLANT THE BELT CHUTE STARTED TO STOP UP AND HE WENT TO TURN OFF THE BELT A ROCK WAS THROWN FROM THE CHUTE STRIKING HIM IN THE BACK OF HIS HEAD JUST UNDER HIS HAR D HAT.

EMPLOYEE WAS MOVING A PIECE OF METAL AND JABBED IT INTO HIS HAND.

LUBRICATING WATER TRUCK TWISTED KNEE

REPAIRING MOVING PC OF METAL DROPPED IT ON GROUND METAL HIT END OF W X 4 ON GROUND WHICH STRUCK L CHEEK AND JAW

THE EE WAS TURNING THE HANDLE ON A WINCH TO MOVE THE STACKER BELT TO A NEW LOCATION. THE WINCH INCREASED IN TENSION AND WHEN HE RELEASED THE BRAKE THE HANDLE HIT HIS RIGHT THUMB.

EMPL INJURED ELBOW ON 9/21 WHILE PULLING LARGE SOCKET WRENCH & FELT BURNING PAIN IN RIGHT ELBOW SINCE ONSET HE HAS HAD WAXING & BURNING PAIN IN SAME LOCATION. HE CONTINUED TO WORK UNTIL 11/ 05 WITHOUT DIFFICULTY. HE WAS EXAMNED BY DR

EMPLOYEE WAS LIFTING A PIPE AND FELT A BURNING IN HIS ABDOMINAL REGION.

EMPLOYEE WAS WELDING ON BELT TAILPIECE FRAME A HOT PIECE OF METAL BURNT THROUGH THE EMPLOYEE'S BOOT EMPLOYEE'S RIGHT FOOT RECEIVED 2ND DEGREE BURN.

EE WAS WORKING ON A WELDING MACHINE ADJUSTING THE CLUTCH HIS HAND SLIPPED OFF THE THROTTLE LEVER CONTROL AND HIT THE METAL FAN BLADE.

EE WAS CLOSING AIR DOORS ON A TRAIN CAR USING AN AIR COMPRESSOR WITH A LINE AND CHUCK WHEN REMOVING THE CHUCK A SUDDEN BLAST OF AIR CAUSED METAL CHIPS TO BE EMBEDDED UNDER THE SKIN OF HIS RIGH T FOREARM.

EMPL WAS MOVING A FRONT END LOADER FROM ONE LOCATION TO ANOTHER EMPL LOST CONTROL ON A DOWN HILL GRADE AND RAN OFF A DIRT EMPBANKMENT

EMPLOYEE WAS LIFTING ON A CRUSHER DOOR-HE FELT A PULL IN HIS LOWER BACK.

EMPL WAS LIFTING AND MOVING TOP BELT ROLLERS WHEN HE FELT A BURNING IN HIS ABDOMEN

EMPLOYEE WAS STANDING ON 2ND FLOOR OF PREP PLANT WHEN A METAL SLEEVE FELT FROM 3RD FLOOR STRIKING EMPLOYEE ON TOP OF SKULL.

EMPL USING PRY BAR TO OPEN & CLOSE DOORS ON TRAIN WE WERE ABOUT TO LOAD.

EMPL WAS INSTALLING LIGHTING IN PREP PLANT 1ST FLOOR. EMPL LOSED BALANCE ON LADDER & FELL 16' STRIKING HEAD ON POWER BOX.

EMPLOYEE WS ATTEMPTING TO MOVE A CROSS BAR TO MAKE ROOM FOR A PIECE OF EQUIPMENT WHEN HE TWISTED HIS BACK.

EMPLOYEE WAS SERVICING HEAVY EQUIPMENT. EMPLOYEE ATTEMPTED TO MOVE A BARREL OF OIL. EMPLOYEE LOST CONTROL OF BARREL OF OIL CAUSING A STRAIN OF LEFT HIP AND BACK AND LEG.

EMPLOYEE WAS LO5DING BELT ROLLERS ON FLAT CAR.EMPLOYEE CAUGHT RIGHT THUMB UNDER ROLLER.

EMPLOYEE WAS WO9KING ON A 4X4 PUMP WHEN A RIB POPPED OFF A PIECE OF COAL HITTING EMPLOYEE ON RIGHT ARM.

EMPLOYEE WAS SU1ERVISING A UNIT SECTION MOVE. EMPLOYEE WAS STANDING BESIDE THE BELT WHEN A SCOOP DISLODGED A TIMBER 8'X10" WHICH FELL STRIKING EMPLOYEE.

RFOOF FALL IN #7 ROOM @#11X-C IN 2ND NO.PANEL OFF MAIN EA.THE FALL WAS 50FTX25FTX8FT

EMPLOYEE WAS IN8TALLING ROOF BOLTS AT THE FACE OF THE COAL. A ROCK FELL BETWEEN THE PINS STRIKING EMPLOYEE ON HIS RIGHT FOOT.

EMPL REMOVING P5NEL ON SHUTTLE CAR.SQUATTED DOWN TO REMOVE BOLTS WHEN HE LOST BALANCE.EMPL FELL ON RIGHT KNEE WHICH STRUCK LUMP OF COAL.

EMP WAS INSTALL3NG ROOF BOLTS AT THE FACE OF THE COAL, A ROCK FELL STRIKING HIS L HAND AND THE HED OF THE ROOF BOLTER. THE ROCK WAS 1" ROUND 4" THICK THE ROOF BOLTER IS EQUIPED WAS ATRS

EMPLOYEE WAS ST5NDING AT MOUTH FO THE MINE ON SLOPE BELT PASSING ROCK DUST TO ANOTHER EMPLOYEE.EMPLOYEE CAUGHT RIGHT FOOT IN WOOD SUPPORT AN TWISTED RIGHT KNEE.

EMPLOYEE STEPPE8 IN MUD HOLE CONTAINING A BOARD WITH A NAIL.THE NAIL PUNTURED RIGHT FOOT.

EMPLOYEE WAS IN8TALLING ROOF BOLTS AT THE FACE OF THE COAL A ROCK FELL FROM BETWEEN BOLTS STRIKING EMPLOYEE ON LOWER LUMBAR REGION.

ROOF FALL 1ST S2 ROOMS OFF WEST OFF MAIN SO 6 CROSSCUT 2 ROOM 30X16X10

ROOF FALL 2ND N2 ROOMS OFF WEST OFF MAIN SO #2 CROSS CUT #3 ROOM INTERSECTION 20X14X10

ROOF FALL SECON8 NO ROOMS OFF WEST MAIN SO #2 CROSSCUT #4 ROOM 40X14X9

ROF FAL NORTH R2OMS OF 1ST WEST OFF MAIN SO #12 CROSS CUT #3 ENTRY FALL WAS 20X17X10

THE BELT DRIVE 2N THE WEST BELT HAD BEEN SLIPPING. HE WAS CHECKING THE CAUSE OF THE SLIPPAGE APPARENTLY THE SPROCKET AND CHAIN BROKE LOOSE STAINING THE BOLTS IN THE GUARD. HE WAS STRUCK BY THE CHAIN, SPROCKET2 GUARD. THE RESULT WAS A BROKEN RIGHT ARM, LACERATION ON FOREUJHEAD, CONTUSIONS

EMPLOYEE WAS HE5PING ROOF BOLTER OPERATOR INSTALL ROOF BOLTS, OPERATOR WAS UNDER ATRS WHEN A ROCK FELL 1'X2'X3" ON THE HELPER (HELPER WASUNDER SUPPORTED ROOF ROCK FELL BETWEEN ROOF BOLTS).

ROOF FAL #J #K 9OOM X CUT TO X CUT 1ST NO ROOMS OFF 1ST WEST OFF MAIN SO 12TH CROSSCUT FAL 90X16X15

ROOF FALL #4 #53ENTRY FROM X-CUT TO X-CUT 1ST NORTH.ROOMS OFF 1ST WEST ROOMS OFF MAIN SOUTH.FALL WAS 50' X 15' X 9'.

ROOF FALL AT 7 9NTRY 11 CROSS CUT IN WEST OFF MAIN SO-UTH. OUTBY WORKING SECTION INTAKE ENTRY.

RECOURRENCE OF 3NJURY ON 12-11-86. EMPLOYEE WAS OPERATING ROOF BOLTER AT THE FACE A ROCK FELL STRIKING EMPLOYEE ON FOWER LUMBAR RESION OF BACK.

ROOF FALL AT XC015 WEST PANEL #5 ENTRY THE FALL 16'X16'X9'.

ROOFFALL XC #173WEST PANEL #6 ENTRY THE FALL WAS 17'X17'X9'.

THE EMPLOYEE WA8 DRILLING A HOLE IN THE ROOF FOR A ROOF BOLT WHEN A ROCK FELL,STRIKING EMPLOYEE ON LOWER LUMBAR REGION.THE ROCK WAS 32" X 16"X4" AND THE ROOF BOLTER WAS EQUIPED WITH AYRS.

ROOF FALL IN #63ROOM #11 X-CUT OF THE 1ST WEST ROOMS OFF MAIN SOUTH. THE FALL WAS 18X18X9.

THE EE WAS OPER5TING A PINNER AT THE FACE WHEN HE SLIPPED ON A ROCK & FELL TWISTING HIS BACK.

EMP WAS REMOVIN1 CABLES FROM BEHIND COAL FEEDER WHEN HE DISLODGED A TIMBER WHICH ROLLED ON HIS LEFT ANKLE CAUSING A STRAIN

THE EMPLOYEE WA8 OPERATING A CUTTING MACHINE AND CUTTING SUMP HOLES, NITCHES, ECT. EMPLOYEE SAID THAT SOME SMALL CHIPS OF ROCKS WERE IN HIS EYES.

ROOF FALL IN #43ROOM, INTERSECTION OF 1ST WEST ROOMS OFF MAIN SOUTH THE FALL WAS 18' X 18' AND 12' IN DEPTH LOADER CABLE & DRILL CABLE WERE COVERED UP. VENTILATION WAS NOT AFFECTED

ROOF FALL IN 5 9M INTERSECTION OF 1 ST WEST RMS OFF MAIN SOUTH THE FALL WAS 18X18 FT AND WAS CLEANED REPAIRED WITH LONGER BOLTS.

ROOF FALL IN #2 ROOM FACE OF 1ST WEST ROOMS OFF MAIN SOUTH THE FALL WAS 18'X25' & WAS DANGERED OFF & T IMBERED OFF.

EMPLOYEE #1 AND3EMPLOYEE #2 WERE CARRYING CROSSBARS TO SUPPORT ROOF EMPLOYEE #2 LOST FOOTING WHICH SHIFTED WEIGHT OF CROSSBAR TO EMPLOYEE #1 CAUSING A LOW BACK STRAIN TO EMPLOYEE

ROOF FALL IN #23ENTRY KEYROOM 3RD X-CUT OUTBY FACE IN 3RD NORTH PANEL OFF MAIN EAST THE FALL WAS 20'X25'X8' & WAS TIMBERED OFF.

EMPLOYEE WAS UN5OADING 6X8X16 CROSS BARS FROM SCOOP, AFTER UNLOADING SEVERAL. CROSSBARS EMPLOYEE LOST GRIP OF ONE CROSSBAR IN TRYING TO REGAIN CONTROL OF CROSSBAR STRAIN LOWER BACK.

EMPLOYEE WAS IN8TALLING ROOF BOLTS AT THE FACE OF THE COAL WHEN POSITIONING ROOF BOLTER TO INSTALL ANOTHER ROOF BOLT EMPLOYEE CAUGHT RT FOOT BOL BETWEEN ROOF BOLTER AND FLOOR OF MINE

ROOF FALL IN #63ENTRY #8 CROSS CUT IN THE 3RD NORTH PANEL OFF THE MAIN EAST THE FALL WAS 17 FT X 16 FT X 8 FT AND WAS TIMBERED OFF

EMPLOYEE WAS AT7EMPTING TO ALIGN THE 3RD NORTH BELT AS HE STEPPED ACROSS THE BELT TO RETRIEVE A SLEDGE HAMMER HE STEPPED ON A SMALL BLOCK OF WOOD TURNING HIS ANKLE

EMP WAS CUTTING3A BROKEN PLASTIC PUMP LINE TO INSTALL A SPLICE AS HE CUT THE PIPE THE BELT KNIFE HE WAS SUING SLIPPED AND CUT HIS LEFT FOREARM

ROOF FELL IN #63ENTRY @#3 CROSSCUT IN THE 3RD PANEL NORTH OFF THE MAIN EAST. THE FALL WAS 17' X 17' X .H AND 125' FROM THE F A CE

ROOF FALL IN #43(BELT) ENTRY @#1 CROSSCUT IN THE 3RD NORTH PANEL OFF THE MAIN EAST THE FALL WAS 17FTX17FTX8FT & COVERED THE FEEDER-BREAKER

ROOF FALL IN #23ENTRY #1 & #2 X-CUTS IN THE 3RD NORTH OFF THE MAIN EAST. THE FALL WAS 25' X 18' X & WAS APPROX 80' FROM THE FACE.

DISCOVERED 2 RO2F FALLS INT HE 3RD NORTH ODD THE MAIN EAST #1 - 20' X 18' X 10' IN #4 ENTRY AT #2 X-CUT.

DISCOVERED 2 RO2F FALLS IN THE 3RD NORTH OFF THE MAIN EAST. #2 20' X 20' X 9' IN #5 ENTRY AT #2 X-CUT.

ROOF FALL #4 EN7RY #32 X-CUT IN THE MAIN EAST ENTRIES. THE FALL WAS 18'X18'X10' & BLOCKED THE SUPPLY ROAD TO THE #1 UNIT.

ROOF FALL AT #73ENMTRY #32 CROSS-CUT IN THE MAIN EAST ENTRIES THE FALL WAS 17FTX17FTX8FT

ROOF FALL AT #43(BELT) ENTRY #30X-CUT IN THE MAIN EAST ENTRIES THE FALL WAS 17FTX20FTX8FT

ROOF FALL IN #63ENTRY #32 CROSS CUT IN THE MAIN EAST ENTRIES THE FALL WAS 16 FT X 17 FT X 8 FT

ROOF FALL IN #53ENTRY #32 X-CUT IN MAIN EAST ENTRIES.FALL WAS 17' X 17' X 8'.

ROOF FALL AT #23ENTRY #31 X-CUT IN MAIN EAST ENTRIES FALL WAS 17' X 16' X 8'.

ROOF FALL IN #23ENTRY #30 X-CUT IN MAIN EAST ENTRIES .FALL WAS 17'X 20' X 8'.

ROOF FALL IN #33ENTRY #32 X-CUT IN MAIN EAST ENTRY.FALL 17' X 17' X 8'.

ROOF FALL ON 1 6NIT 2 ENTRY 28 X CUT IN THE MAIN EAST ENTRIES 17FTX17FTX8FT.

ROOF FAL IN #4 6ELT ENTRY #27 CROSS CUT IN THE MAIN EAST ENTRIES FALL WAS 16X17X8

EMPL MOVING SC 7O BUILD A BOLCK BRATTICE.AS HE MOVED CAR,RAN INTO THE RIB CAUSING CANOPY TO FALL ON HIM.EMPL DIDNT REPORT INTO HOSPITAL UNTIL 6-2-86 FOLLOWING REGULAR WORK SHIFTS.

ROOF FALL IN TH9 INTERSECTION OF #12 X-XUT #4 ROOM ON THE INTAKE SIDE OF THE 2ND NORTH PANEL OFF THE MAIN EAST 17FT X 17 FT X 7 FT

EMPL INSTALLING3X-OVERS AND WAS STRUCK IN THE EYE BY PIECE OF STEEL WHILE TIGHTENING ROOF BOLT.

ROOF FALL AT IN7ERSECTION OF 20 X CUT ROOM 2 ON THE INTAKE SIDE OF THE 2ND NORTH PANEL.

ROOF FALL IN 2N8 NORTH PANEL AT #1 ENTRY #28 CROSS CUT 85 FT X 18 FT X 9 FT COVERED ON GALIS 320-A

EMPLOYEE WAS IN8TALLING ROOF BOLTS AT THE FACE APIECE OF ROCK FELL THROUGH THE HOLE IN THE CANOPY AND PINNED THE EMPLOYEES LEFT HAND TO THE PINNER BOOM

EMPLOYEE SAID T2AT HE HAD CLIMBED ON THE BOOM OF THE ROOF BOLTER LOST HIS BALANCE AND FELL ONTO THE ROOF BOLTER

ROOF FALL IN I3TERSECTION #4 ENTRY A 33 CROSS CUT IN 2ND NORTH MAIN EAST

EMPL SHOVELING 5OOSE MATERIAL UNDER MAIN SOUTH CONVEYOR BELT.AS HE LIFTED SHOVEL FULL OF MATERIAL FELT SHARP PAIN IN LOWER BACK AND WAS UNABLE TO MOVE.

THE EMPLOYEE WA8 HELPING INSTALL A CONVEYOR BELT LAY WHEN HE STEPPED ON A LUMP OF COAL AND TWISTED HIS ANKLE. HE WAS ABLE TO COMPLETE HIS REGULAR SHIFT.

AS A GROUP OF M9N WERE PULLING ON A 2 IN PLASTIC WATER LINE THE SHAFT OF A GATE VALVE BECAME CAUGHT ON THE EMPLOYEE S LEFT FOREARM THE SHAFT THEN PENETRATED THE EMPLOYEES FOREARM WHEN THE WATE R LINE WAS PULL9D AGAIN

THE EMPLOYEE WA8 DRILLING A HOLE IN THE ROOF FOR A ROOF BOLT.WHEN A PIECE OF ROCK FELL.STRIKING THE EMPLOYEE ON THE LEFT FOREARM.

EMP WAS DRILLIN1 A HOLE IN THE ROOF FOR A ROOF BOLT WHEN A PIECE OF ROCK FELL, STRIKING HIM ON THE LEFT ELBOW

EMP WAS INSTALL3NG ROOF BOLTS WHEN A LARGE PIECE OF ROCK FELL ONTO THE CANOPY OF THE PINNER. THE ROCK BROKE IN HALF AND F ELL FROM THE CANOPY LANDING ON EDGE BEHIND HIM, THE ROCK THEN FELL TO WARD HIM PINNIN1 HIS LEFT LEG AGAINST THE CANOPY JACK

EMP WAS DRILLIN1 A HOLE IN THE ROOF FOR A ROOF BOLT WHEN A PIECE OF ROCK FELL STRIKING THE CANOPY AND THEN SLIDING OFF THE CANOPY ONTO THE EMPLOYEES BACK

EMPLOYEE WAS PU5LING A 2 IN PLASTIC WATER LINE THROUGH A HOLE IN A BLOCK BRATTICE WHEN IT BECAME STUCK WHEN THE EMPLOYEE JERKED ON THE LINE IT CAME LOOSE AND STRUCK THE EMPLOYEE IN THE MOUTH

ROOF FELL IN I 3TERSECTION OF #3 ENTRY #26 CROSSCUT IN THE 2ND NORTH PANEL

EMPL WALKING BE2IND PINNER BEING TOWED TO #1 UNIT.SLIPPED ON SOME LOOSE MATERIAL IN SUPPLY ROAD AND FELL CATCHING WEIGHT WITH RIGHT HAND.

EMP WAS INSERTI3G A GLUE CARTRRIDGE AND ROOF BOLT INTO THE BOLT HOLE WHEN THE ROTATION ENGAGED CAUSING A 2' EXTENSION WRENCH IN THE CHUCK TO STRIKE HIM ACROSS THE NOSE

WHILE DRILLING 5 BOLT HOLE AT THE FACE, A LARGE PIECE OF ROCK FELL ONTO THE CANOPY OF THE PINNER. A SMALL PIECE OF THIS ROFK BROKE OFF ON IMPACKXX IMPACT AND FELL BEHIND THE TRAM LEVERS OF THE PINNER, CAUSING3THE PINNER TO RUN OVER THE OPERATOR, PINNING HIM TO THE RIB

ROOF FALL IN I3TERSECTION OF #2 ENTRY #20 CROSS CUT IN THE 2ND NORTH PANEL

EMPL UNLOADING 8UPPLIES FROM SUPPLY TRAILER.HE HAD PLACED BUCKET OF SCOOP ON END OF TRAILER AND WAS LOOSENING CHAINS HOLDING SUPPLIES WHEN SCOOP BUCKET SLIPPED OFF TRAILER AND PINNED EMPL LEFT FOOT TO MINE F5OOR.

DISCOVERED ROOF3FALLS AT #1 ENTRY, #10 CROSS CUT AND #2 ENTRY, #11 CROSS CUT IN THE SECOND NORTH PANEL.

EMP WAS ATTEMPT3NG TO MOVE A CENTRIFUGAL PUMP THAT HAD BECOME STRUCK IN THE MUD, ASHE PULLED ON THE PUMP, HE SAID THAT HE FELT SOMETHING GIVE IN HIS LOWER BACK

DISCOVERED ROOF3FALLS AT #1 ENTRY, #9 CROSS CUT, #3 ENTRY, #9 CROSS CUT, AND #7 ENTRY, #9 CROSS CUT IN THE SECOND NORTH PANEL.

THE EMPLOYEE WA8 DRILLING A HOLE IN THE ROOF WHEN THE GLOVE ON HIS LEFT HAND BECAME CAUGHT BY THE DRILL STEEL, PULLING HIS THUMB OUT OF JOINT AND CAUSING A LACERATION OF THE WEB BETWEEN THE TH UMB AND 1ST FIN1ER.

AS THE EMPLOYEE3WAS LOADING COAL AT THE FACE OF #2 ENTRY, A LARGE PIECE OF ROCK FELL ON THE FRONT END OF THE LOADER. THE FORCE OF THE IMPACT THREW THE EMPLOYEE AGAINST THE TOP OF THE CANOPY, JAMMING HIS NE7K.

AS THE EMPLOYEE3WAS DRILLING A HOLE INTO ROOF, A SHOT WAS PUT OFF 4 ENTREIES OVER. THE SHOT JARRED A PEICE OF TOP COAL LOOSE WHICH FELL, STRICKING THE EMPLOYEE ON THE LOWER BACK.

DISCOVERED ROOF3FALLS AT #5 ENTRY, #22 CROSS CUT, #5 ENTRY, #19 CROSS CUT, AND #6 ENTRY, #23 CROSS CUT IN THE MAIN EAST ENTRIES.

DISCOVERED ROOF3FALLS AT #4 ENTRY, #21 CROSS CUT AND #4 ENTRY, #23 CROSS CUT IN THE MAIN EAST ENTRIES.

AS THE EMP WAS 4ORKING ON THE CABLE REEL OF A SHUTTLE CAR, THE LOADER BACKED INTO THE SHUTTLE CAR. THIS CAUSED THE REEL COVER TO FALL ON THE EMPLOYEES RIGHT ARM

EMP WAS USING A3HAMMER AND CHISEL TO REMOVE BIT KEEPERS FROM AN OLD CUTTING MACHINE CHAIN. AS HE STRUCK THE CHISEL A STEEL FRAGMENT STRUCK HIM ABOUT 8" BELOW HIS NAVEL AND BECAME IN BEDDED UND ER THE SKIN 3

WHILE RECLAIMIN1 BELT FRAMING, EMP STRUCK A PIECE OF FRAMING WITH A SLEDGE HAMMER. WHILE STRIKING THE F RAME, A STEEL CHIP STRRUCK HIS RIGHT FOREARM

EMP WAS CLEANIN1 MUD OUT OF A DITCH UNDERGROUND AS HE LIFTED A SHOVEL OF MUD HE FELT A PAIN IN HIS LOWER BACK

ROOF FALL AT #13ENTRY, #1 CROSSCUT IN THE MAIN SOUTH ENTRIES.

THE EMPLOYEE WA8 DRAGGING A WATER HOSE TO HIS COAL DRILL WHEN A PIECE OF ROCK FELL FROM BETWEEN THE ROOF BOLTS AND STRUCK HIM ON THE HEAD AND SHOULDER.

AS THE EMPLOYEE3WAS INSERTING A 7 SECTIONAL DRILL STEEL INTO THE BELT HOLE, A PEICE OF ROCK FELL FROM THE TOP, STRICKING THE EMPLOYEES LEFT HAND AND CAUSING IT TO STRIKE THE BOOM OF THE PINNER . 3

EMPLOYEE WAS WASHING OUT A CONCRETE PUMP AFTER MAKING A POUR HE HAD FAILED TO NORIFY SUPERVISOR OF HOLES IN HIS RUBBER BOOTS AND WHEN THE CONCRETE LEAKED THRU HOLES AND CAME IN CONTACT WITH HI S FOOT IT RESULTED IN CONCRETE BURNS

CREW WAS CLEANING UP MUCK THAT HAD ACCUMULATED ON THE SCOPE INVERT EMPLOYEE SLIPPED ON THE LOOSE MUCK AND FELL ON HIS LEFT HAND, BREAKING A BONE NEAR HIS WRIST.

EMP WAS HELPING3TO REPLACE THE ELECTRICAL PANEL COVER ON A SHUTTLE CAR WHEN THE PANEL COVER FELL ON HIS LEFT FOOT

EMP HAD REMAINE8 AFTER THE END OF HIS SHIFT TO HELP MOVE THE UNIT POWER BOX CLOSER TO THE FACE

ROOF FALL- 1ST NORTH, #6 ENTRY, #8 CROSSCUT 20\X20\X6\.

MAIN SOUTH 1 ENT 8 X CUT.

ROOF FALL

EMP WAS LOADING WELDING TANK ONTO SUPPLY CAR WHIN IT BEGAN TO SLIDE OFF THE CAR EMP CAUGHT THE TANK CAUSING A STRAIN TO HIS RT SHOULDER

I.NAME, SECTION FOREMAN, STOPPD THE CONVEYOR BELT TO REMOVE A LARGE PIECE OF ROCK. WHEN THE ROCK FELL FROM THE BELT, IT LANDED ON EDGE AND STARTED TO FALL TOWARD THE BELT. I.NAME ATTEMPTED TO STOP THE ROCK FROM FALLING, AND HAD HIS MIDDLE FINGER ON THE RIGHT HAND CAUGHT BETWEEN THE ROCK AND THE BELT ROPE.

I.NAME THE SHOT FIRER WAS LOADING EXPLOSIVES AT FACE WHEN A LARGE PIECE OF GOB FELL FROM THE ROOF BETWEEN THE ROOF BOLTS STRIKING HIM ON THE RIGHT SHOULDER

MS#3611X-ROOF FALL

MS-3 Q9X ROOF FALL.

I.NAME & I.NAME WERE ATTEMPTING TO JACK UP & REPAIR A CRIB THAT HAD BEEN HIT BY A S/C. AS I.NAME STARTED TO USE THE JACK THE CRIB ROLLED OVER ON H IM PINNING HIS RIGHT LEG. I.NAME WAS NOT I NJURED.

I.NAME WAS GREASING THE ROOF BOLTER WHEN A SMALL PIECE OF ROCK FELL FROM THE ROOF AND STRUCK HIM IN THE SMALL OF THE BACK. THE COAL HEIGHT WAS APPROXIMATELY 8 1/2 FEET.

ROOFFAL 6 ENTRY 2 CROSSCUTR MAIN SO ENTRIES 40X18X8

I NAME WAS ATTEMPTING TO WELD A DIODE IN PLACE IN A LONG AIRDOX FEEDER BREAKER WITHOUT USING A WELDING HOOD. HE RECEIVED FLASH BBURNS OF BOTH EYES.

I.NAME AND A 2ND MAN WERE LOADING A PIECE OF ANGLE IRON ON THE SLOPE CAR. I.NAME WAS PLACING HIS END ON THE CAR WHEN THE 2ND MAN DROPPED HIS END, THIS CAUSED THE ANGLE IRON TO JUMP OFF OF THE CAR, STRIKING I.NAME ON THE CHEST

UNIT FOREMAN, I,NAME WAS INSPECTING SOME LOOSE JOB IN NO.1 CROSS-CUT WHEN A SMALL PIECE FELL, STRIKING HIM ON HIS HARD HAT.