Email me when a new MSHA incident is filed at Corinth Prep Plant.
| Quarter | Hours worked | Citations | S&S | Per 1M hrs |
|---|---|---|---|---|
| 2025 Q4 | 5,301 | 2 | 1 | 377.3 |
| 2025 Q3 | 6,021 | 0 | 0 | 0.0 |
| 2025 Q2 | 7,346 | 1 | 0 | 136.1 |
| 2025 Q1 | 7,488 | 0 | 0 | 0.0 |
| 2024 Q4 | 7,693 | 2 | 0 | 260.0 |
| 2024 Q3 | 6,505 | 0 | 0 | 0.0 |
| 2024 Q2 | 8,845 | 0 | 0 | 0.0 |
| 2024 Q1 | 8,097 | 0 | 0 | 0.0 |
Employee was descending through an access door in the floor of the plant when EE caught thigh on the grating causing a cut to EE's left thigh.
Employee was using battery powered grease gun to track conveyor belt over, continuous pumping led to a buildup of pressure, grease gun tubing exploded bruising right orbital area above eye.
EE and another ee were removing bolts from a pump on the prep plant. EE was using a pull bar to break the bolts loose. As he strained, he felt a pain and burning to his lower abdomen and groin area. No visible injury: however he has had 2 prior hernia surgeries. He was taken to Urgent Care.
Contract coal hauling tandem axle truck left scale house road loaded and after entering haul road to his right continued to veer right driving into drainage ditch and turning truck on right side.
Prep plant lost power.Plant operator(certified electrician)found the breaker tripped at main transformer on top floor of plant.He checked area,phase monitor,etc.and reset breaker.As he was closing door, an electrical flash occurred causing slight and severe burns to left hand; slight burns to left side of face and neck; and right hand.(Locking pin fell from door onto power phase).
Co-worker was operating the crane, to lift a 12x20 metal building, and set it in place. While employee was holding and steadying the building as it was being lowered, the building swung around and mashed/cut ring finger on left hand on leg of crane. 13 stitches.
EE and other ee were replacing elevator buckets on the prep plant. As he let off the comealongs, a metal elevator bucket slipped-knocking him against a metal angle brace. The metal angle brace struck his right shoulder and right side.
EE was re-setting a breaker. An electrical flash occurred causing burns to his upper chest, face, and left side of his head.
Employee was walking around a parked boom truck to go to the fines prep plant. He bent down to walk under the boom. He hit his head on the boom and he jerked backwards causing pain and injury to his back.
MECHANIC WAS TROUBLE SHOOTING AN ELECTRIC PROBLEM ON A SKID STEER LOADER. THE CAB WAS OPEN TO ACCESS WIRING DURING THE PROCESS OF CHECKING OPERATION OF CIRCUIT THE ENGINE WAS STARTED, VIBRATIO N CAUSED THE CAB TO CLOSE, WHICH HAD NOT BEEN LOCKED.
RUBBER MAT ON FLOOR OF CONTROL PANEL WAS TRIPPED ON AND EE SPRAINED ANKLE.
SLIPPED; LOST FOOTING WHILE GREASING TAIL BEARING. FELL WHILE STEPPING ON BEAM 36" OFF FLOOR.
THREE EMPLOYEES WERE INSTALLING A 25 HP ELECTRIC MOTOR ON THE PREP PLANT. THE MOTOR WAS BEING POSITIONED SO THAT IT COULD BE BOLTED DOWN. THIS EMPLOYEE HAD HIS RIGHT ARM BETWEEN THE MOTOR AND THE SHAFT. THE MOTOR STRUCK HIS RIGHT ARM BELOW THE ELBOW. CONTUSION, BRUISING AND SOME SWELLING RESULTED.