Lucerne No 9 Mine Coal

UNINTENTIONAL ROOF FALL OCCURRED IN THE #5 ENTRY OF 1 NORTH. APPROX DIMENSIONS ARE 40' L X 18' W X 5' H. LOCATED APPROX. 65' INBY S.S. #57, AREA WAS SUPPORTED WITH 48" RESIN BOLTS.

EMPLOYEE REPORTEDLY STRUCK HEAD AGAINST SCOOP CANOPY PLEASE NOTE MEDICAL TREATMENT ONLY

EMPLOYEE REPORTEDLY WENT TO CHECK PUMP AT SLOPE.

UNINTENTIONAL ROOF FALL OCCURRED IN THE #4 ENTRY INTAKE OF 5 SOUTH APPROX 50' INBY SURVEY STATION #981. THE DIMENSIONS ARE 37' LONG X 18' WIDE X 7' HIGH. AREA WAS SUPPORTED WITH FIBER CRIBS, CRIBS, XBARS, AND POSTS.

EMPLOYEE WAS EXITING AN OFFICE WHEN HIS HAND HITTHE CORNER OF A PARTS CABINET.

EMPLOYEE REPORTEDLY FELL WHILE WALKING DOWN SLOPE STEPS.

EMPLOYEE HAD CAUGHT FOOT BETWEEN TRACK RAIL AND DAWG ON LOCOMOTIVE.

EMPLOYEE REPORTEDLY STRUCK HEAD ON ROOF SUPPORT WHILE WALKING ALONG SLOPE BELT WALKWAY.

EMPLOYEE REPORTEDLY WAS STRETCHING OUT HOSE FOR INSTALLATION IN A SUMP, SLIPPED ON WET BOTTOM.

THE EMPLOYEE REPORTEDLY WAS HANDLING CONTINUOUS MINER TRAILING CABLE.

EE REPORTELY WAS ASSISTING AN EMPLOYEE WITH THE INSTALLATION OF STEEL VENTILATION PIPE.

EE REPORTEDLY FELT PAIN FROM PERFORMING NORMAL WORK DUTIES.

THE EE REPORTED THAT HIS BACK STIFFENED UPON REACHING THE WORKING SECTION.

AN UNINTENTIONAL ROOF FALL OCCURRED IN THE 7 NORTH NO 1 RETURN ENTRY. 1 X CUT OUTBY SS @2462. DIMENSIONS ARE 18.25' W X 130' LONG X 5-6'HIGH.

THE EMPLOYEE WAS STRUCK BY LID WHILE WORKING ON 15 TON LOCOMOTIVE

EMPLOYEE REPORTEDLY STRUCK HIS HEAD ON ROOF SUPPORT WHILE TRAVELING E-2 ESCAPEWAY. BEGAN MISSINGWORK 9-8-94.

EMPLOYEE REPORTEDLY WAS LIFTING BELT SCRAPER.

EMPLOYEE REPORTEDLY WAS MOVING MINER CABLE IN ORDER TO MVOE HIS ROOF BOLTING MACHINE.

THE FALL OCCURRED IN THE 2 WEST 5 SOUTH SECTION APPROX 50' INBY SURVEY STATION 1350 A UNINTENTIONAL ROOF FALL. THE DIMENSIONS OF THE FALL 50' X 20' X 6' H. AREA WAS ABANDONED ROUTE REMARKED.

EMPLOYEE REPORTEDLY FELL WHILE WALKING

THE FALL OCCURRED IN T HE OLD 5 SOUTH TRACK ENTRY 100 FT INBY SURVEY STA #1133 THE CAVE IS 90FT IN LENGTH BY 20FT WIDE BY 6 TO 8FT IN HEIGHT THE AREA WAS SUPPORTED WITH 6FT RESIN BOLTS 6 0LB S TRACK RAILS & CENTER POSTED

EMPLOYEE REPORTEDLY SLIPPED WHILE REPAIRING MACHINE.

EMPLOYEE REPORTEDLY STRUCK HIS HEAD ON A ROOF BOLT HEADER WHILE WALKING.

EMPLOYEE WAS ATTEMPTING TO REMOVE ROCK FROM ATOP MACHINE.

EMPLOYEE REPORTED THAT WHILE WALKING HE STRUCK HIS HEAD AGAINST A RUN-THRU BOARD.

EE WAS STRUCK IN EYE WITH TREE LIMB.

THE EMPLOYEE WAS STRUCK BY A PIECE OF LOOSE ROOF FROM BETWEEN THE ROOF BOLTS

THE EMPLOYEE WAS STRUCK BY A PIECE OF SLATE BROKEN FROM AROUND AROUND A ROOF BOLT.

EMPLOYEE WAS WALKING IN THE 2 RIGHT 7 NORTH SECTION.

EMPLOYEE WAS PERFORMING NORMAL WORK DUTIES. DIAGNOSIS- CARPAL TUNNEL SYNDROME. BEGAN MISSING WORK ON 8-31-94.

AN UNINTENTIONAL ROOF FALL OCCURRED IN THE 4 WEST 7 SOUTH NO. 2 ROOMS. 3 X-CUTS INBY SURVEY STATION 3692. APPROX. DIMENSIONS 18' WIDE. 4-5' HIGH IN INTERSECTION. AREA WAS TIMBERED AND ABANDONE D. AREA WAS SUPPORTED WITH 48" RESIN BOLTS AND TIMBERED PRIOR TO ROOF FALL.

EMPLOYEE REPORTEDLY WAS LIFTING A TOOL BOX ONTO THE 6 TON MANTRIP.

EE WHILE WALKING LOOKING FOR PARTS STRUCK TOOL SKID.

THE EMPLOYEE WAS LIFTING A CABLE AT FEEDER OF THE 1 RIGHT 7 NORTH SECTION WHEN HE EXPERIENCED BACK PAIN.

EE REPORTED THAT HE STRUCK HIS HEAD ON A BELT HANGER WHILE WALKING I8N THE 2 RIGHT 7 NORTH SECTION.

EMPLOYEE REPORTEDLY WAS PICKING UP A BAG OF ROCKDUST FROM THE MINE FLOOR.

EE WAS LOADING TOOLBOX ONTO MANTRIP AND EXPERIENCED PAIN IN BACK.

EMPLOYEE REPORTEDLY WAS WALKING IN 1 RIGHT 7 NORTH BELT/TRACK ENTRY.

EMPLOYEE COMPLAINS OF ONGOING PAIN IN LEFT FOREARM FROM OPERATING SHUTTLE CAR.DIAGNOSED CARPAL TUNNEL SYNDROME 03-19-94.

EMPLOYEE WAS PERFORMING NORMAL WORK DUTIES WHEN HE REPORTED SORENESS IN SHOULDER.

AN UNINTENTIONAL ROOF FALL OCCURRED IN THE 1 RIGHT 7 NORTH ROOMS AT SS 3558. THE DIMENSIONS OF THE FALL WERE APPROX. 20' W X 6-7' H X 90' LONG. THE AREA WAS BOLTED WITH 48" FULLY GROUTED ROOF BOLTS.

EMPLOYEE WAS REMOVING BELT STRUCTURE FROM IDLE TAILPIECE IN THE 4 WEST 7 SOUTH SECTION WHEN HIS THUMB WAS CAUGHT BETWEEN IDLER AND FRAME.

EMPLOYEE REPORTEDLY WAS STRUCK IN THE MOUTH BY A POGO STICK WHILE TIGHTENING A CANVAS CHECK.

EE WAS REPORTEDLY LIFTING HIS TOOL BAG ONTO HIS SHOULDER AND FELT STRAIN IN HIS BACK.

EMPLOYEE WAS ATTEMPTING TO CUT OPEN A BAG OF SAND WHEN HE CUT HIS HAND AT THE BOTTOM OF 7 SOUTH TRACK.

THE EMPLOYEE WAS THROWING THE TRACK DERAIL SWITHCH HANDLE AT THE NO. 4 MAIN DRIVE AREA WHEN HIS FINGER WAS STRUCK BETWEEN THE SWITCH TRHOW & SWITCH FRAME.

THE EMPLOYEE REPORTEDLY PASSED THROUGH METAL MANDOOR & REACHED BACK TO PULL DOOR CLOSED. THE FORCE OF THE AIR CLOSED THE DOOR ON HIS HAND.

AN UNINTENTIONAL ROOF FALL OCCURRED IN 7 SOUTH LEFT SIDE RETURN ESCAPEWAY E-2 INBY SS 2076. APPROX. DIMENSIONS: 20' X 20' X 15' HIGH. AREA WAS SUPPORTED BY 6' RESIN BOLTS. AREA WILL BE TIMBERE D AND REROUTED.

AN UNINTENTIONAL ROOF FALL OCCURRED IN THE LEFT SIDE 7 SOUTH ESCAPEWAY E-2 INBY SS 3182. APPROX. DIMSINSIONS: 20' X20' X 8' HIGH. AREA WAS SUPPORTED BY 4' GULLY GROUTED RESIN BOLTS. AREA WILL BE TIMBERED AND REROUTED.

EMPLOYEE EXPERIENCED BACK PAIN WHILE RERAILING A 6TON LOCOMOTIVE AT 4 NORTH SWITCH USING LIFTING JACK

THE EMPLOYEE WAS CLEANING OUTSIDE SHOP - ATTEMPTED TO LIFT AXEL SHAFT WHEN IT SLIPPED FROM HIS HAND ONTO TOP OF LEFT FOOT.

THE EMPLOYEE WAS ATTEMPTING TO HANG UP A TRAILING CABLE WHEN HE REPORTEDLY STRUCK HIS HEAD AGAINST THE MINE ROOF.

THE EMPLOYEE REPORTEDLY INJURED HIS BACK WHILE ATTEMPTING TO ADJUST SEAT ON THE SHUTTLE CAR.

EMPLOYEE WALKED INTO MINER CABLE HUNG FROM MINE ROOF IN THE 1 RIGHT 7 NORTH SECTION.THIS WAS REVEALED THROUGH A PART 50 AUDIT AT THIS MINE.

THE EMPLOYEE REPORTEDLY WAS WALKING IN THE 1 RT 7 NORTH NO.3 ENTRY WHEN HE STEPPED IN A HOLE IN THE MINE BOTTOM APPROX. 4" DEEP X 2 1/2' IN DIAMETER.

7 SOUTH LEFT SIDE RETURN E2 ESCAPEWAY OLD 6 SOUTH BELT TRACK ENTRY 6 CROSS CUTS OUTBY SURVEY STATION 1843. THE DIMENSIONS APPROX. 20 FT WIDE X 60 FT LONG X 7 TO 8 FT HIGH AREA WAS SUPPORTED WI TH 60 INCH FULLY GROUTED RESIN ROOF BOLTS AND SUPPLEMENTAL, CRIBS H BEAMS ROOF MATS ROUTE WAS CHANGED AND AREA DANGERED OFF.

EMPLOYEE REPORTED THAT HE WAS TRYING TO GET AROUND THE ELEPHANT EAR ON THE SHUTTLE CAR TO WORK AT RE-ENTERING THE CABLE WHEN HE FELT PAIN IN HISBACK. BEGAN CHIROPRACTOR TREATMENT ON APRIL 12, 1993.

EE WAS WALKING IN 5 RM OF 1 RIGHT 7 NORTH LOOKED UP AND STRUCK HEAD ON ROOF RAIL.

EE WAS DRAGGING SNUB JACK WHEN HE FELT PAIN IN HIS LOWER BACK.

EMPLOYEE REPORTEDLY WAS MOVING MINER CABLE WHEN HE EXPERIENCED BACK PAIN.

EMPLOYEE WAS LOADING POST FROM THE SUPPLY CAR INTO THE SCOOP BUCKET HE REPORTED THAT HE EITHER PULLED OR T WISTED SOMETHING IN HIS LOWER BACK

WHILE WALKING UP #6 HEADING EMPLOYEE REPORTEDLY HIT HIS HEAD ON THE ROOF.

EMPLOYEE WAS PULLING & STACKING MINER CABLE WHEN HE WENT HOME THAT NIGHT HE FELT NUMBENSS & PAIN I HIS LEFT ARM WRIST & FINGERS MEDICAL DIAGNOSIS TENDONITIS

EMPLOYEE WAS RIDING IN THE BACK OF MANTRIP-HIS HEAD HIT AN OVERCAST.

THE EMPLOYEE WAS SITTING IN THE MANTRIP WITH LEGS STRETCHED OUT AND FEET CROSSED OVER.THE RIGHT FOOT CAUGHT BETWEEN THE CANOPY OF ROOF RAIL.

EE WAS TIGHTENING BOLTS ON FISH PLATES ON 2 RIGHT TRACK. THE WRENCH SLIPPED OFF THE NUT AND EE HIT HIS LEFT KNEE ON TRACK RAIL.

EMPLOYEE WAS LOOSENING A LIGHT MOUNTING BOLT WHEN THE WRENCH HE WAS USING SLIPPED OFF OF BOLT LETTING HIS FINGER STRIKE THE FRAME OF THE LIGHT MOUNTING BRACKET.

WHILE LIFTING A BAG OF BOLTER DUST INTO THE SCOOP BUCKET HE HURT HIS LOWER BACK.

EMPLOYEE WAS CROSSING UNDERNEATH THE BELT AT #2 TAIL AS HE CROSSED UNDER HE TWISTED HIS BACK

EMPLOYEE WAS LOADING HIGH VOLTAGE CABLE ON A SUPPLY CAR WHEN HE FELT PAIN IN HIS LOWER BACK

EMPLOYEE WAS TRYING TO PUT MORE OF A CURVE ON THE END OF THE HOOK USING THE EYE OF A ROOF PLATE THE HOOK SLIPPED OUT HE FELL CATCHING OR BREAKING HIS FALLL WITH HIS LEFT HAND

EMPLOYEE WAS PICKING BAGS UP & PLACING THEM INTO THE SCOOP BUCKET WHEN HE NOTICED PAIN IN HIS LOWER BACK

EMPLOYEE WAS OPENING THE AIR-LOK DOOR ON THE 4 WEST TRACK WHEN HE HIT HIS HEAD ON A ROOF BOLT HEAD.

EMPLOYEE HAD A PIECE OF DIRT COME IN BEHIND HIS GLASSES & THE DIRT WENT INTO HIS EYE THE INJURED WAS WEARING SAFETY GLASSES

EMPLOYEE WAS GETTING OUT OF SHUTTLE CAR WHEN HE SAID HE TWISTED HIS BACK.

EMPLOYEE REPORTEDLY WAS PERFORMING NORMAL DUTIES OPERATING A SHUTTLE CAR EMPLOYEE BEGAN LOSING TIME ON 03-10-93 WAS DIAGNOSED AS HAVING A DEGENERATIVE DISC DISEASE

1 RIGHT 7 NORHT LOCATION OF THE FALL: STATION #3284 JUST INBY AT INTERSECTION. THE DIMENSION OF THE FALL: 8'X18'X40' SIX FOOT (6') AND EIGHT FOOT (8') RESIN BOLTS WERE BEING USED.

2 RIGHT 7 NORTH THE LOCATION OF THE FALL: STATION #3266 - #5 ROOM 3 X-CUTS INBY. THE DIMENSION OF THE FALL 25'X19'X5' ADDITIONAL POSTS USED FOR PILLARING. FOUR FOOT (4') RESIN BOLTS WERE BEING USED.

EE WAS MAKING HIS DAILY MINE EXAMINATION WALK WHEN HIS LEFT KNEE STARTED GIVING HIM TROUBLE THIS PAIN OCCURRED BECAUSE OF HIS REPOREATED WALKING OF LONG DISTANCES.

THE DIMESNION OF THE FALL: 18'X35'X8' THE LOCATION OF THE FALL: 1 XCUT OUTBY STATION #3213. THE LOCATION OF THE FALL: 1 XCUT OUTBY STATION #3213. 6' INSTALL II ROOF BOLTS WERE BEING USED. IMMD EDIATE ROOF CONSISTED OF SHALE.

1 RIGHT 7 NORHT THE LOCATION OF THE FALL: 1 X-CUT INBY STATION #3218. THE DIMENSION OF THE FALL: 20'X20'X6'-7' 6' RESIN BOLTS WERE BEING USED. IMMEDIATE ROOF CONSISTED OF SHALE SLATE.

INJURED EMPLOYEE WAS WALING ALONG 4 WEST 7 SO TRACK WHEN HE COMPLAINED TO HIS FOREMAN EE THAT HE HAD HIT HIS HEAD ON A BENT ROOF BOLT HEIGHT WSA 66INCHES

7 SOUTH PARALLELS THE LOCATION OF THE FALL APPROX. 75 FT INBY STATION 3123. THE DIMENSION OF THE FALL APPROX. 75 FT LONG X 18FT WIDE X 8 FT HIGH. IMMEDIATE ROOF S ONSITED OF SHALE. ADDITIONAL ROOF SUPPORT H BEAM4 FT RESIN BOLTS BEING USED.

EMPLOYEE WAS OPERATING A 15 TON MOTOR ALONE IN 7 NORTH TRACK, WHEN HE STRUCK HIS HEAD ON A 60 LB RAIL THAT WAS USED TO SUPPORT THE ROOF. FELT PAIN IN HIS NECK AND RIGHT SHOULDER.

EMPLOYEE WAS SHOVELING ALONG 7 NORTH BELT-HE FELT PAIN IN HIS RIGHT SHOULDER.

38505E WAS SHOVELING ALONG 7 SOUTH LOWBELT IN THE AREA AROUND THE LOW DRIVE MOTOR. AS SHE LIFTED THE SHOVEL SHE SLIPPED, TWISTING HER BACK.

54736YEE WAS WALKING IN THE #1 HEADING OF 1 RIGHT 7 NORTH 35' INBY STATION #2076 WHEN A PIECE OF SLATE FELL HITTING HI ON THE BASE OF THE NECK.

7 SOUTH THE LOCATION OF THE FALL:STATION #3141 INBY 1 X-CUT THE DIMENSION OF THE FALL:3" THICK X12" WIDE X21" LONG.SIX FOOT ROOF BOLTS WERE BEING USED.

EMPL WALKING IN THE 7 SO.SECTION,STRUCK HEAD ON A ROOF BOARD INSTALLED ON THE ROOF.

LOADING BELT STRUCTURE-PICKED UP A TOP ROLLER AND TWISTED LOWER BACK.STARTED MISSING WORK 7-13- 92.

EMPLOYEE REPORTEDLY WAS WALKING IN BELT ENTRY STRUCK HIS HEAD ON BELT HANGER. (BEGAN LOSING TIME 5/19/93 - DIAGNOSIS BILATERAL CARPAL TUNNEL SYNDROME) (OCCUPATIONAL ILLNESS)

4 WEST 7 SOUTH 1X-CUT INBY SPAD #3041 IN #2 ENTRY DIMENSIONS 18FTWX30FTLX4FT-5FTH 4FT RESIN BOLTS WERE BEING USED

EMPLOYEE WAS WALKING FROM PARKING LOT TO A LAMHOUSE WHEN HE SLIPPED AND TWISTED HIS ANKLE.

2RT 7 NORTH DIMENSION OF THE FALL 18FTWX180FTLX8FTH LOCATION OF THE FALL STA #2817 INSTALL 1A-6FT&8FT SUPPLEMENTARY ROOF SUPPORT ROOF MATS TIMBER

1 RIGHT 7 NORTH L/S RETURN #800 E2 ESCAPEWAY. THE DIMENSION: 18' W X APPROX. 8' H APPROX. 120' L. THE LOCATION: APPROX. 4 X-CUTS OUTBY STATION #2651-9 X-CUTS INBY STATION 2534 2 PC. INSTAL #2- 6' BOLTS BEING USED.

EMPLOYEE WAS WALKING PAST THE MANTRIPS.LOCATED ON THE BOTTOM AT #1 DRIVE,(CARRYING AN ELECTRIC DRILL.)HE HIT HIS HEAD ON ONE OF THE H-BEAMS AND JAMMED HIS NECK.

WHILE INSTALLING ROOF BOLTS ALONG THE RIB LINE THE RIB ROLLED OUT AGAINST THE OPERATOR PUSHING HIM UP AGAINST THE ROOF BOLTER CAUSING HIS HAND TO PUSH BACKWARDS.

FOUND IN 7 SOUTH SECTION -MMU-017 DIMENSION OF FALL- 26' X 24' X 6'HIGH ROOF BOLTS BEING USED-6' IMMEDIATE ROOF CONSISTED OF SHALE.

EMPL WAS OPERATING SHUTTLE CAR-WHILE TRAMMING TO FACE,THE CANOPY OF HIS CAR HIT THE FIRE EXTINGUTUISHER HANGING ALONG THE HAULAGE CAUSING IT TO DISCHARGE AND SPRAYED FACE AND EYES.

EE WAS GETTING OUT OF MANTRIP WHEN HIS FOOT CAUGHT THE SIDE OF THE MANTRIP AND TWISTED HIS LEG.

EMPLOYEE WAS HELPING UMWA EMPLOYEE WHO HAD ASKED FOR HELP. HE HELPED HIM LOAD TIMBER AND WHILE BENDING OVER ISD OF SKID TO LIFT TIMER, STRAINED LOWER BACK.

7 NORTH THE DIMENSION OF THE FALL-25' LONG X25' WIDE X6' HIGH.THE LOCATION OF THE FALL WAS AT STATION #2654 LENGTH OF ROOF BOLT 8'.

INJ HELPING OTHER ADJUST THE LOWER PLATFORM OF THE HYD.PRESS. OTHER RELEASED THE CHAIN FROM THE PLATFORM CAUSING IT TO FALL ON EMPL FINGER.

EMPL THROWING CRIB BLOCK OUT OF THE WAY OF SCOOP.STARTED MISSING WORK 1-20-92.

EMPL WALKING INTO SECTION AND HIT HEAD ON ROOF JAMMING NECK CAUSING PAIN IN NECK AND SHOULDERS. STARTED MISSING WORK 12-12-91.

OPER RF BOLTER STEELS DROPPED STRIKING HIM ON HEAD AND JAMMING NECK

EMPLOYEE REPORTED THAT HE WAS HAULING COAL FROM THE MINER TO THE FEEDER AND THE CAR HIT A POT HOLE AND HE BOUNCED UP AND HIT HIS HEAD ON THE CANOPY.

EMPLOYEE WAS BLOCKING SCOOP WITH CRIB BLOCK WHEN HE WAS PLACING BLOCK UNDER TIRE OF SCOOP HE H IT HIS FINGER AGAINST SIDE OF SCOOP & CRIB BLOCK

EMPLOYEE WAS LOADING 38" BELT ON EMPTY SUPPLY CAR.

DIMENSTION APPROX 30' L X 14' W X 4' HIGH LOCATION OF FALL 1 X CUT OUTBY STATION #2105 2 X CUTS INBY STATION #2086. UNUSUAL GEOLOGIC FORMATIONS CUTTER THIS FALL WAS FROM CAVE THAT PREVIOUSLY B OLTED & CLEANED UP. ADDITIONAL SUPPORT H BEAMS STRINGER CRIBS ROOF MATS HEADERS ON BOLTS.

EMPL WAS LOOKING AT SOME SMALL PARTS FROM DISMANTLED VALVE BANK ON CONTINUOUS MINER. HE HAD JUST TAKEN HIS GLASSES OFF TO SEE PARTS BETTER. MINER OPERATOR ACCIDENTLY TURNED MANUAL START BUTTON TO ON POSITION INSTEAD OF OFF PSOITION STARTINGPUMP MOTOR. OIL SPRAYED FROM VALVE BANK STRIKING MECHANIC IN FACE & EYES.

BUILDING WALL, L HAND LAY ON BLOCK OTHER FELL ON IT

UNTWISTING CANVAS FELT PULL IN BACK

OUTBY- #7 ENTRY OF MAINS. THE LOCATION OF THE FALL: 2 X-CUTS INBY SPAD #902. THE DIMENSION OF THE FALL: 18'X18'X6' ADDITIONAL ROOF SUPPORT - 60# RAILS. 6' RESIN B OLTS WERE BEING USED.

EE WAS REMOVING A SHUTTLE CAR CABLE FROM INSULATED HOOKS WHEN HE GOT SHOCKED AND BURNED ON BOTH HANDS EVIDENCE OF BURN MARKS ON LITTLE FINGERS.

EE STATED THAT WHILE HE AND 3 OTHER PERSONS THREW A 60 LB TRACK RAIL UP ON THE RAIL CAR THE RAIL SPRANG BACK. HE TRIED TO HOLD THE RAIL, WAS AT THIS POINT HE PULLED MUSCLE IN RIGHT ARM. THE RE ASON THE RAIL SPRANG BACK WAS BECAUSE THE OTHER END OF THE RAIL WAS CAUGHT IN BETWEEN OTHER RAILS LYING ON THE BOTTOM.

WHILE STEPPING OVER PIECE OF MINE CANVAS,EMPL STEPPED ON NAIL THAT WAS STUCK IN CANVAS.NO LOST TIME-MEDICAL.

EMPLOYEE WAS WALKING TO WORKING SECTION FROM MATRIP AT START OF SHIFT.HE SLIPPED AND FELL INJURING HIS RIGHT SHOULDER.

EE WAS CARRYING CRIB BLOCK WHEN HIS HAT FELL OFF HIS HEAD. HE TOOK A STEP OR TWO AND STRUCK HIS HEAD ON A ROOF BOLT.

EMPLOYEE WAS HELPING MECHANIC PUT GATHERING ARM BACK ON MINER WHEN THE ARM SLIPPED STRIKING LEFT HAND.

EMPLOYEE STATED THAT WHILE DRILLING A HOLE HE FELT SOMETHING IN HIS EYE. HE DIDN'T FEEL TAHT ANYTHING CAME IN AROUND HIS GLASSES, THAT IT MIGHT BE AN EYELASH. AFTER REPEATED FLUSHING NOTHING C OULD BE SEEN IN THE EYE BUT THE EYE WAS IRRITATED AND RED.

EMPLOYEE STATED HE FELT SOMETHING PULL IN HIS LOWER BACK WHEN HE WAS MOVING MINER CABLE OUT OF THE WAY.HE ALSO STATED BOTTOM WAS MUDDY AND HE SLIPPED.EMPLOYEE SAID HE WAS LIFTING PROPERLY.

UNINTENTIONAL ROOF FALL,2 X CUTS INBY STATION 2633,DIMENSION OF FALL IS 20'X20'X8' HIGH.ROOF CONSISTED OF SHALE AND SANDSTONE.SECTION INVOLVED-7 NORTH.

AN ALLEGED METHANE IGNITION OCCURRED IN #2 FACE OF 7 NORTH SECTION-FEDERAL ID #001.

RF FALL 2 X CUTS INBY 2689 100' L 18'W 8'H FOUR FOOT RESIN BOLTS BEING USED

2 WEST 7 SOUTH, LOCATION OF FALL: #10 ROOM OFF #6 ENTRY OF 7 SOUTH. DIMENSIONS OF FALL 110' LONG X 20' WIDE X 8' HIGH. 4' RESIN BOLTS WERE BEING USED.

THE LOCATION OF THE FALL: 1659 #3 HEADING. THE DIMENSIONS OF THE FALL: 22'L X 20' W X 8'H. ROOF BOLTS: 6' INSTALL II. ADDITIONAL SUPPORT- BOX BEAMS.

1 RIGHT 7 NORTH-E2 L/S RETURN. THE LOCATION OF THE FALL: 8 X-CUTS INBY STATION #2534 AND #0 ROOM. THE DIMENSION OF THE FALL: 18 X 60 X 6' PLUS. ROOF BOLTS USED: 6' INSTAL 2.

1 RIGHT 7 NORTH THE LOCATION OF THE FALL AT STATION 2648 THE DIMENSION OF THE FALL 35FT LONG X 18FT WIDE X 6-8 FT HIGH 6 FT INSTALL BOLTS WERE BEING USED.

EMPL WAS WALKING TO FACE FROM MANTRIP WHILE WALKING HE BUMPED HEAD ON MINE ROOF. HE STATED THIS MADE NECK SORE.

WHILE WALKING 7 NORTH AIRCOURSE ON L/S RETURN INJ EMPL STEPPED INTO WATER HOLE & LOST BALANCE & TWISTED LEFT KNEE. DID NOT START MISSING WORK UNTIL 8/29/91.

EMPLOYEE WAS PULLING BELT AROUND STATIONARY PULLEY TO COUPLE BELT TOGETHER, MADE WRONG TURN AND PULLED ON LOWER BACK.

EMPL WAS PUSHING WHEEL BARREL & ROW OF CRIBS. WHEEL BARREL GOT STUCK BETWEEN CRIBS. TRYING TO PULL WHEEL BARREL BACK HE PINCHED FINGER ON CRIB.

...ORIGINALLY SUBMITTED AS A NO LOST TIME. HOWEVER,EMPL STARTED MISSING WORK DUE TO 5-29-92 INJURY ON 8-14-91.BEING RESUBMITTED AS A LOST TIME.

EMPLOYEE STATED THAT A SUPPLY CAR CAME OFF THE TRACK AND AFTER JACKING IT UP HE WAS PLACING A HEADER UNDER THE CAR WHEN HE FELT PAIN IN HIS LOWER BACK AND RIGHT LEG.

EE WAS TRAMMING SHUTTLE CAR AROUND CORNER OF STUMP. PINCHED LITTLE FINGER BETWEEN KITCHEN OF HSUTTLE CAR AND COAL RIB.

THE LOCATION 6 ENTRY ADJACENT TO SPAD 2629 IN 5 ENTRY THE DIMENSION 19 FT WIDE X 80FT LONG X 4-5 FT HIGH 4 FT RESIN BOLTS WERE BEING USED.

REACHING FOR A BLOCK TO BUILD A WALL ON OVERCAST,LEFT HAND CAME IN CONTACT WITH METAL BAND CUTTING RING FINGER ON LEFT HAND.

AIR COURSES -E2-6SOUTH AREA.LOCATION OF FALL- 2 X-CUTS OUTBY STATION 1723.DIMENSION-35'LONG X 19'WIDE X 5'8"HIGH.IMMEDIATE ROOF CONSISTED OF SHALE.OLD OVERCAST BOLTED WITH 4' CONVENTIONAL BOLT

EMPLOYEE WAS TRAMMING MINER THROUGH BACK CHECK WHEN HE STEPPED IN HOLE ON BOTTOM AND FELL ON RIGHT KNEE.

EMPLOYEE CLAIMED HE WAS DONE PLUGGING SCOOP PLUG IN WHILE HE WAS POSITIONED FROM THE TOP OF SCOOP BATTERY AS HE WAS BACKING OF BATTERY IN A LAYING POSITION HE STRUCK ELBOW ON BATTERY I.D. HOLD DOWN WHICH IS 2 ROOF PLATES WELDED ON TOP OF ONE ANOTHER WITH AN 8' BOLT THROUGH BOTH OF THEM.

EMPL GOT OUT OF CAR AND RESET FEEDER POWER.WALKING BACK TO SHUTTLE CAR -THERE IS A BOOM HOLE CUT IN THIS AREA WITH 12" ROCK CUT OUT.WALKING THROUGH THIS AREA,STRUCK HEAD HURTING NECK.

EE WAS LIFTING A TOP ROLLER TO PUT IN PLACE AND PULLED HIS LOWER BACK OUT.

EMPLOYEE REPORTED THAT HE WAS OPENING A BAG OF B-BOND AND MATERIAL FLEW UP INTO HIS FACE-BLINKED OUT-FINISHED SHIFT-INFLAMMATION SHOWED UP THE NEXT DAY.

SHOVELING RIB PULLED MUSCLE IN BACK

EMPLOYEE WAS BOLTING, HE DROPPED THE CANOPY ON BOLTER AND WAS STRUCK ON TOP OF HEAD COMPRESSING HIS NECK.

1 RIGHT 7 NORTH THE LCATION OF THE FALL 4 ENTRY 1 X CUT INBY STATION 2539. THE DIMENSION OF THE FALL-21 L X 19FT W X 8 FT H. COMBINATION BOLTS WERE BEING USED 6 TO 8 ADDITIO NAL OR SUPPLEMENTARY ROOF SUPPORT POST AND CRIBS

EMPL WAS ROOF BOLTING ON RIGHT SIDE OF BOLTER HE SLIPPED OF ROCK & FOOT WENT BETWEEN TWO ROCKS & HE TWISTED KNEE.

RUNNING SHUTTLE CAR HIT HOLE HEAD HIT CANOPY

HELPING TO INSTALL SAIL BOAT STANDING BACK WAS HELPING TO HOLD UP TOP OF SAIL BOAT WHILE ROOF BOLT WAS PUT IN. EMPL STARTED MISSING WORK ON 5/23/91 BECAUSE OF THIS INJURY.

1 X CUT INBY SPAD 2579 160'L 18' W 8'H

WHILE CUTTING A BLOCK TO FIT IN THE WALL THE EDGE OF THE AX WENT THRU THE BLOCK. HIS HAND WAS WRAPPED AROUND THE AX HANDLE AND HIS FINGER HIT THE BLOCK.

WALKING FELT PAIN IN BACK LEGS HURT

1RT 7NO LOCATION OF FALL 1RT 7NOL/S RETURN ROOM 6,7,8 & X-CUT TO 6TO7&XCUT7TO8 DIMENSION OF THE FALL APPROX ROOM 7-18FTWIDE&50FTLONGXCUT 7-8-18FTWIDE&100FT LONG 8FT COMBINATION COMPRESSION BOL TS WERE BEING USED SUPPLEMENTARY ROOF SUPPORT BEING USED STRAPS

GETTING SHOVEL FROM MINER, BUMPED RUB RAIL AND IT FELL ON LEFT IN-STEP.

7 SOUTH. THE LOCATION OF THE FALL- 1 X-CUT INBY SPAD 2363 #4 HEADING. THE DIMENSION OF THE FALL- 20' X 20' X 8' HIGH. 8' COMBINATION BOLTS- RAILS IN INTERSECTION WERE BEING USED. ADDITIONAL OR SUPPLEMENTARY ROOF SUPPORT- H-BEAMS- 60 LBS RAILS.

EMPLOYEE WAS UNLOADING TOP BELT ROLLERS FROM UTILITY MOTOR. HE TOOK A ROLLER OFF THE PILE AND AS HE DID, ANOTHER ROLLER SLID AND STRUCK HIM ON THE RIGHT HAND.

EMPLOYEE WAS HELPING TO INSTALL A BOOM JACK ON THE BOLTER WHEN HE GOT HIS FINGER PINCHED BETWEEN THE OUTSIDE OF JACK AND FRAME OF MACHINE.

EMPLOYEE STATED THAT HE WAS WALKING AROUND OPERATOR'S SIDE OF BOTTOM WHEN HE SLIPPED AND TRIED TO CATCH HIMSELF ON SIDE OF BOLTER HURTING HIS SHOULDER.

MOVING MINER CABLE COMP OF SORE BACK

EMPLOYEE WAS WALKING BETWEEN SHUTTLE CAR AND RIB. THERE WAS SPILLAGE ALONG RIB AND A PIECE OF ROCK LYING ON A 45 DEGREE ANGLE LYING IN THE SPILLAGE. THE INJURE STEPPED ON THE ROCK AND SLIPPED OFF THE ROCK AND FELL AGAINST THE RIB, THEN FELL ON THE BOTTOM. THERE WAS AN OFFSET APPROX. 1' IN THE RIB AND HE FELL ONTO THE OFFSET.

WHILE LOADING A 1000' 7200 CABLE ONTO THE SUPPLY CAR A FOREIGN OBJECT FLEW INTO HIS EYE. HE WAS WEARING HIS SAFETY GLASSES.

EMPLOYEE WAS PULLING HIGH VOLTAGE CABLE IN THE BBELT ENTRY WHEN HE FELT A PAIN IN HIS LOWER BACK.

TRYING TO TAKE O RING FROM FITTING TOOL SLIPPED CUTTING INDEX FINGER ON L HAND

HELPING MOVE CABLE INJ SHOULDER

EMPLOYEE WAS WALKING TO MANTRIP WHEN HE STEPPED INTO HOLE IN BOTTOM TWISTING HIS ANKLE.

6 SOUTH (SECTION HAS BEEN FINISHED FOR SEVERAL YEARS) THE LOCATION OF THE FALL-#3 ENTRY AT SPAD #1740 OLD BELT LINE 6 SOUTH. THE DIMENSION OF THE FALL-APPROX 30' LONG-20' WIDE-8-10' HIGH. 5' R ESIN BOLTS WERE BEING USED. 5 BOLTS ACROSS & OLD BELT LINE (WAS CENTER TIMBERED AND STRAPPED).

EMPLOYEE WAS SITTING IN OPERATORS COMPARTMENT OF MINER PULLING LEVER THAT SUCK OIL INTO THE MINER HE SHUT THE MINER OFF AS THE MINER HELPER WAS PUTTING THE CAP BACK ON THE FILL HOSE WHEN THE M INER WAS SHUT OFF OIL SPRAYED OUT OF THE HOSE & STRUCK EMPLOYEE IN THE RIGHT EYE (HE WAS WEARING HIS SAFETY GLASSES)

EMPLOYEE WAS CROSSING THE 7 NO BELT AT 1RT 7 NO HEAD & WHEN HE STEPPED DOWN FROM X-OVER HE STEPPED ON A 4IN T & TRIPPED & FELL TWISTING HIS LOWER BACK

EMPLOYEE GRABBED TOOL BAGS OFF OF MANTRIP AND IN DOING SO TWISTED HIS LOWER BACK.

EMPL TAKING OUT TOP ROLLER ALONG#3 MAIN BELT,SLIPPED OFF BOLT CUTTING LEFT WRIST.

EMPL SPLITTING CAP PIECES FOR TOP OF STOPPING.EMPL STRIKING DOWN ON CAP PIECE WHEN RIGHT WRIST CAME IN CONTACT WITH METAL BAND STICKING UP ALONGSIDE PALLET OF TILE.

EE WAS DROPPING THE BOOM DOWN ON THE BOLTER AND AT THE SAME TIME PUT HIS HAND ON THE BOOM CAUSING HIS THUMB TO GET SQUEEZED BETWEEN A HOSE AND THE DRILL MOTOR.

EE WAS CHANGING A HYDRAULIC HOSE ON A BOLTER. EE WAS BENT OVER THE BOLTER FOR ONE HOUR. HIS BACK WAS STRAINED FROM ALL THE BENDING OR PULLING ON THE HYD. HOSE CAUSED HIS BACK TO HURT.

EMPLOYEE WAS BOLTING X5-6 WHILE DRILLING A LARGE PIECE OF ROCK BROKE LOOSE & FELL ON CANOPY EMPLOYEE LOWERED THE CANOPY TO REMOVE ROCK & THE BACK OF ROCK BROKE OFF STRIKING EMPLOYEE ON THE BAC K

MAINS APPROX INTERSECTION 7 X CUTS OUTBY SPAD #1389 ENTRY #1. DIMENSION OF FALL 20 X 20 X 8 SIX FOOT COMBINATION BOLTS WERE BEING USED. ADDITIONAL SUPPORT OF TRUSSES & CRIBS WERE BEING USED. U NUSUAL GEOLOGIC FORMATIONS CUTTERS.

7 NORTH-INY SPAD 2X-CUTS FROM SPAD THEN GO 5 X-CUTS TO THE RIGHT.WAS IN E2 ESCAPEWAY IN OLD ROOMS.THE DIMENSIONS OF THE FALL 80'X18'X8'.

EMPLOYEE WAS BOLTING #1 ENTRY-SAFETY POST WAS UP AGAINST THE ROOF AND THE PROTECTIVE CANOPY IN 8" BELOW ROOF LINE.EMPLOYEE WAS WALKING FROM SIDE TO WORK AREA UNDER CANOPY WHEN HE STRUCK HIS HE AD ON TEH CANOPY CAUSING PAIN IN THE NECK.

EMPL WAS TAKING SCRAPPER OFF OF LOW DRIVE. HE DROPPED SCRAPPER ON FINGER. INJ EMPL WAS WEARING GLOVES.

PAIN IN LOWER BACK

SLIDING I BEAMS OFF SCOP ON BOLTER PULLING BEAM SPRAINED BACK

EMPLOYEE STATED AS HE GOT OUT OF THE HYSTER TO CHECK WHY THE OVERLAND BELT WAS OFF HE SLIPPED ON THE SECOND STEP WHICH MAY HAVE HAD A THIN COAT OF ICE ON IT. AS HE GRABBED THE RAIL HE SLIPPED AND FELT A PAIN IN HIS LEFT SHOULDER AREA.

WALKING THROUGH CANVAS CHECK. HIT HEAD ON H-BEAM.

EMPL WAS HOVELING COAL FROM UNDER #1 LOW BELT DRIVE & EXPERIENCED SEVERE BACK PAIN WHEN THROWING COAL ONTO BELT.

WAS WATCHING FEEDER FOR ROCK THAT WAS BEING DUMPED ON BELT. HE WAS TAKING A ROCK OFF OF THE BELT AND HE SAID HE PULLED SOMTHING IN HIS BACK.

EMPLOYEE WAS PUTTING TOP ROLLER BACK ON THE RAIL.

EMPLOYEE WAS RIDING IN MOTOR TO SECTION. HE FELT A SHARP PAIN IN HIS RIGHT HIP AND LOWER BACK.

EMPLOYEE WAS CUTTING OUT SPILLBOARDS FOR FEEDER AND HOT SLAG SPIT BACK INTO HIS FACE AND CAUSED A PIECE OF SLAG TO GO INTO HIS EYE.EMPLOYEE WAS WEARING HIS SAFETY GLASSES.

4 SOUTH-THE LOCATION OF THE FALL-166' INBY #1 ROOM.THE DIMENSION OF THE FALL-PILLARING FINAL PUSH OUT-SIZE OF PILLAR 80'X70'.THIS AREA WAS TIMBERED ACCORDING TO PILLARING PLAN.

EMPLOYEE WAS PUTTING WEDGES WHEN ROCK FELL OFF AND HIT HIS HAND.

EMPLOYEE REPORTED THAT HE HAD A PIECE OF COAL IN HIS BOOT. HE REMOVED HIS BOOT TO TAKE THE COAL OUT OF IT AND LOST HIS BALANCE. HE TRIED TO CATCH HIMSELF. HIS LEFT FOOT KICKED INTO A CRIB. INJURING HIS LITTLE TOE ON HIS LEFT FOOT.

#2 HEADING OF MAINS-THE LOCATION OF THE FALL -#2 OF MAINS-3 X-CUTS INBY SPAD #65.THE DIMENSION OF THE FALL 6' HIGH 30' LONG 18' WIDE.FIVE FOOT RESIN BOLTS WERE BEING USED.THERE WAS AN ADDITION AL ROW OF POSTS ALONG EDGE OF PREVIOUS CAVE.

EMPLOYEE WAS PICKING A ROCK UP WITH ANOTHER EMPLOYEE & WENT TO THROW IT ONTO THE BELT EMPLOYEE STRUCK POST PINCHING HAND BETWEEN ROCK & POST ROCK WAS APPROX 14IN -16IN LONG-4IN TO 6IN THICK & 6IN TO 8IN WIDTH

7 NORTH-THE LOCATION OF THE FALL-1 X-CUT INBY 2375.THE DIMENSION OF THE FALL-18'WIDE-50' LONG-10-12' HIGH.EIGHT FOOT COMRESSION BOLTS WERE BEINGUSED.

EMPLOYEE REPORTED THAT HE WAS PUTTING A COAL CHAIN TOGETHER ON A 1410 MINER,HE WAS HOLDING LINK WITH ONE HAND,HE SWUNG HIS HAMMER AND THE HAMMER HIT THE TAIL OF THE MINER AND IT GLANCED OFF AN D HIT HIS LEFT THUMB.

EMPLOYEE WAS WALKING PAST SUPPLY CARS THROUGH THE OVERCAST WHEN HE STRUCK HIS HEAD ON A SUPPORT FOR THE OVERCAST JAMMING HIS NECK.

EMPLOYEE WAS INSTALLING 8' COMPRESSION BOLT.PUTTING BOLT TOGETHER IN ROOF.SPINNING BOLT AT COUPLER.FINGER GOT CAUGHT AGAINST ROOF AND COUPLER.