Allen Pit & Plant Metal/Non-Metal

Driller needed old conveyor belt cut for dust covers. Driller helped cut out an example and instructed employee to cut two more out. While cutting belt with a utility knife with right hand knife slipped off of belt and struck left hand below the thumb.

Skid steer bucket struck employee's left leg

while changing drill stem on blast drill, pipe wrench would not bite stem. EE was helping it bite the stem. When it did bite, it pinched EE's right hand between wrench and boom mast.

Equipment operator, hauling rock to crusher, in light rain, applied brakes and lost control of CAT 770 off road truck. Laid truck on right side. When seat belt unbuckled, operator fell through right side window, cutting head.

Installing concrete barricades at Quarry entrance. Front end Loader was lifting barricades while removing cribbing from end of barricade cribbing pinched right index finger.

Replacing top screen sections on screen deck on shaker #6 employee was lifting screen section to place it on screen deck. Screen slipped out of employee's hands and fell and came in contact with right middle finger. Employee was taken to ER and received stitches & returned to work with no restrictions from ER doctor. Was instructed to see a orthopedic doctor on 1/23/2017.

The 988 was loading shot rock onto 770 haul trucks. While waiting on trucks to return to pit. Operator move a large rock from loading area the rock slipped out of his bucket causing operator's body to jerk like whiplash. Tightness in the shoulder area. Check by a physician had a slight muscle strain.

Tension on V Belts was being adjusted when employee slipped, to prevent falling he grabbed V Belts. The V Belts rolled backwards pinching his finger between the sheave and V Belts.

Employee's job task was to fuel and service a water pump in the west pit. While he was walking to his vehicle he stepped on a rock causing him to sprain his ankle.

Employee's task for the day was to help change the wear plates on the secondary crusher. While unbolting the old wear plates it was cracked and the piece that was cracked came off and pinched his left pinky finger.

Employee's job duties was to help with drilling and blasting operations. Driller had a problem when he was setting up on next drill hole drill pipe disconnected from power head . Employee was attempting to move pipe in pipe rack and pinched his right thumb between two pipes in pipe rack.

EE's job assignment was stripping old floor tiles off of subfloor in q.c. lab. He was using a floor stripping hand chisel. EE was on subfloor and had left arm in front of him for support, the chisel slipped out from under the tile and struck his lower left arm. This resulted in a laceration on lower left arm. No restrictions.

Driving water wagon uphill on ramp from stockpile area to truck scales. Machine lost power, started rolling backwards. Brakes failed, rolled approx 100', jacknifed on level ground. The EE unbuckled his seat belt & jumped or was thrown from cab.

EE was climbing off of side of conveyor when he became entangled in wiring mounted on side of conveyor, causing him to lose his balance and fall appr 4'. EE landed on his hands and knees, causing injury to his left knee.

Loose material sloughed causing rear tires of trailer to drop off stockpile. Trailer turned over on its side causing the road tractor to turn over on its side. The air filter, ferring, mirror, hood were damaged on the road tractor.

Employee was driving a Peterbilt Semi Tractor with a belly dump trailer. Was stockpiling material. EE drove truck through app 6" of water and struck an object which caused the truck to jump, jarring the ee and injuring his back.

EMPLOYEE WAS CUTTING A PIECE OF CONVEYOR BELT, PULLING THE KNIFE TOWARDS HIMSELF WHEN THE KNIFE SLIPPED AND CUT EE'S LEFT LEG ABOVE THE KNEE RESULTING IN AN INJURY REQUIRING (3) STITCHES TO THE SURFACE OF THE WOUND.

EE WAS DIGGING INTO BANK TO LOAD TRUCK. A ROCK FELL ON LOADER AND HE GOT OUT TO SEE WHERE THE ROCK FELL. THE LOADER STARTED TURNING, HE JUMPED OFF AND HURT HIS LEG.

EE WALKED UP BESIDE SKID LOADER AND LOADER OPERATOR DID NOT SEE HIM & RAN OVER HIS TOES.

EE WAS CLEANING CLOSE TO CRUSHER WHEN ROCK CAME OFF CRUSHER AND HIT HIM.

EMPLOYEE WAS WORKING ON EQUIPMENT. HE GOT UP TO GET MORE TOOLS. HE HIT HIS FACE ON THE DOOR OF THE TOOL BOX ON THE SIDE OF PICKUP.

EE AND ANOTHER EE WERE PUTTING A GUARD BACK ON THE SECONDARY CRUSHER. THE OTHER EE HAND SIPPED AND THE GUARD FELL ONTHE INJURED EE'S HAND.

EMPLOYEE WAS WALKING PAST CRUSHER COMING BACK FORM LUNCH WHEN A ROCK FELW FROM IT AND HIT HIM ON HEAD.

CLIMBING ON LOADER. SLIPPED AND HIT MOUTH.

HE WAS LIFTING 5 GALLON BUCKET TO PUT OIL IN WARE PEDESTA AND STRAINED BACK.

HE WAS WORKING ON CRUSHER. HE STEPPED OFF CRUSHER FRAME ON A ROCK AND TWISTED HIS ANKLE.

INJURED WAS WORKING ON ACCELERATOR ON R-25 TIGHTENING A BOLT, WRENCH SLIPPED AND CAUGHT HIS FINGER BETWEEN WRENCH AND BRACKET.

INJURED WAS REMOVING SHAFT FROM CRUSHER. WHEN SHAFT CAME LOOSE HE MASHED HIS THUMB UNDER SHAFT.

INJURED WAS WORKING ON A TRANSMISSION WHEN PART OF IT FELL ON HIS WRIST.

EE HAD STARTED A REAR DUMP. HE WAS COMING DOWN OFF THE BUMPER TO THE STEPS WHEN HE SLIPPED AND FELL TO THE GROUND. HITTING HIS LEFT SHOULDER, HEAD BACK AND RIGHT LEG.

EE WAS LIFTING A PIECE OF STEEL WITH A HEAL BAR. WHEN HE REACHED FOR THE STEEL, THE BAR SLIPPED AND THE STEEL MASHED HIS FINGER.

EMPLOYEE WAS SHOVELING UNDER CRUSHER, BENDING OVER, A BLOT CAME OFF WING ON SIDE OF CRUSHER, THE WIND MOVED & SOME ROCK CAME OUT & HIT HIM ON THE HEAD BELOW HIS HARD HAT.

IT WAS VERY WINDY HE WAS SHOVELING AT THE CRUSHER & GOT DIRT IN HIS EYE

INJURED WAS PICKING UP CLAY BALLS. HE WENT TO PICK ONE UP AND HURT HSI BACK. IT DID NOT HURT VERY BAD AT FIRST, BUT HURT WORSE THE NEXT DAY. BY MONDAY 3-29-93 HIS BACK WAS REALLY SORE.

2 MEN WERE CLEANING OUT SHOOT UNDER GRIZZLY. THE INJURED WAS WARNED BY OTHE REMPLOYEE THAT HE WAS STARTING UP THE SHAKER. THE INJURED ACKNOWLEDGED HE UNDERSTOOD THE SHAKER WAS GOING TO BE STA RTED. WHEN THE OTHER MAN WENT TO START THE SHAKER THE INJURED PUT HIS HAND ON THE BELT THAT RAN THE SHAKER AND HIS HAD WAS PULLED INTO THE PULLEY.

A ROCK HUNG IN CRUSHER.EMPLOYEE GOT OUT OF HIS LOADER TO HELP CRUSHER MAN DISLODGE ROCK.THEY GOT ROCK DISLODGED AND HE INSTRUCTED THE CRUSHER MAN TO BUMP THE CRUSHER TO SEE IF THE ROCK WOULD F ALL.THE ROCK FELL AND A PIECE CAME BACK AND HIT HIM ON THE TOP OF HIS HEAD.

INJURED WAS CLEANING AROUND THE CRUSHER WHEN A ROCK FELL OFF THE CONVEYOR AND HIT HIM ON THE KNEE.

HE WAS WELDING ON END OF IDLER ONE OF THE SPARKS BURNED HIS EAR.

I NAME WAS HELPING PUT A CONVEYOR BELT ON CRUSHER HE WAS STANDING IN THE FRAME WORK PULLING THE BELT WITH A ROPE WHEN HIS FOOT SLIPPED & HE FELL

SCRAPING LOADER WITH RAZOR BLADE SO IT COULD BE REPAINTED CHANGED BLADE, IN SCRAPER AND PUT OLD BLADE IN POCKET. HE FORGOT HE PUT BLADE IN POCKET AND PUT HAND IN POCKET AND CUT HAND.

WHILE OPERATING LOADER BECAME DISORIENTED AND ALMOST PASSED OUT

HE WAS LIFTING FERTILIZER BAGS TO LOAD A SHOT FOR DYNAMITING WHEN E HURT HIS BACK.

RELEASING A BOOMER ON TRALER AND CHEATER PIPE SLIPPED.

FILINF ON BOLT HOLE IN FRAME OF DOZER AND STEEL FLEW IN EYE.

MOVING FROM I B9AM TO ANOTHER TWISTING HIS RT HKKNEE

THE INJURED GOT3INTO THE WATER TO CHECK SUCTION ON WATER PUMP. STEPPED ON OBJECT AND CUT HIS RIGHT FOOT

REPAIR BELT ON CRUSHER-STRAINED HIS BACK

THE INJURED WAS STEPPING OFF LOADER LAST STEP HAD PIECE BROKEN OFF SO HE FELL ABOUT 18 INCHES TO THE GROUND, HE BROKE HIS NAKLE.

MOVING FROM 1 BEAM TO ANOTHER TWISTING THE RIGHT KNEE.

MOVING FROM ONE I-BEAM TO ANOTHER TWISTING EMPL RIGHT KNEE.EMPL HAVING 2ND OPERATION ON SAME RIGHT KNEE.4-20-84 GOT 2ND OPINION FOR ANOTHER OPERATION AND IS STILL OFF.

GETTING SHAFT OUT OF DRILL WITH SLEDGE HAMMER PIECE OF STEEL PENETRATED INJUREDS LEFT LEG