Amrize Sloan Quarry #1001: 495 MSHA citations Metal/Non-Metal

Employee was building scaffold over conveyor belt. Employee slipped 18 inches catching armpit on the scaffold bar. This dislocated EE's shoulder. Shoulder was put back in place same day.

Miner drove a loader across feeder #1 when material had been removed. The plant operator had triggered feeder #1 and failed to communicate to the loader operator. The miner was injured as the wheels on the loader dropped into the feeder, causing miner to experience multiple body strains.

While getting loaded the loader operator jarred the 777 haul truck that the employee was operating straining their neck and back. Employee's official notification date is in question. The official notification was given on 5/26/2021

Driving over bumps near the face causing EE to bounce around in the cab of the haul truck. Note: Initial treatment did not involve reportable treatments (restricted duty or prescriptions). Employee was released to full duty. On a follow up visit on 8/13/2019 employee was given prescriptions and was recommended therapy

NOT WORK RELATED. Just after EE got to work EE began feeling chest pains. EE notified the safety coordinator. EE was transported to the Office to await emergency medical service. EMT's arrived the pain had decreased and the onsite EKG showed normal stat's. EE was transported to the hospital under the advice of the EMT's.

Employee was climbing up dozer to fuel the machine, as ee grabbed the grab bar ee right hand, ee left foot slipped causing ee to strain left shoulder.

While replacing the shaft guard on a D10 ripper laying on a work bench the injured felt a back strain.

At 5:17 during the work place exam, an employee discovered a body at the clarifier, an unknown individual that came into the mine site and committed suicide according to metro police investigators.

Struck tooth on loader bucket with hammer while attempting to remove. A piece broke off striking the thigh

Employee failed to wear safety glasses while walking accross the yard when the wind was blowing. Claimed to have gotten something in his left eye.

Installing large bull gear on roll crusher at Wash Plant One, using a 8 lb. hammer to strike a hammer wrench to secure the nut that holds the gear. Hammer glanced off wrench and hit left knee.

Removing a rock from Grizzley chute with a come a long. Chain slipped off the rock and rock smashed pinky finger.

Removing bolts on a truck differential, two bolts broke off as he was pushing and pulling and pulled a muscle in back.

Employee was repairing a power cable (S/O 480v) that was pulled out of strain relief. He was moving the cable to get slack for the repair. There was cut or worn spot that shorted out causing an arc that caused first and second degree burns on right hand and thumb.

Employee stepped down from a pedestal to a platform when he stumbled and tripped and fell towards the midrail of the handrail causing injury to forehead and nose. Employee received stitches on the forehead and had a bone fracture of the nose.

EE WAS CLIMBING DOWN FROM LOADER AND FOOT SLIPPED OFF STEP. HE FELL BACKWARDS AND LANDED ON HIS BACK AND HIT HIS HEAD.

Went into the screen to clear a jam in the rock chute. Was getting out of the machine onto ladder, foot stuck and pivoted foot resulting in a strain/sprain to left ankle.

Setting screen box, crane raised. While raised employee reached up to check the load to twist it, and pinched his right thumb.

while exiting the truck, missed the last step and slipped

Crossing over drill, slipped, caught self with right arm (pulling shoulder)

Slipped off equipment in the rain.

EMPLOYEE WAS LOWERING THE LINER INTO THE CHUTE WITH THE CRANE, THE LINER WAS A LITTLE TOO WIDE, EMPLOYEE STOPPED THE CRANE OPERATOR & WAS TRIMMING THE LINER. THE LINER SLIPPED DOWN THE CHUTE & THE UPPER END CAME UP PINNING THE EMPLOYEE.

Employee was changing a tool bar on a D9N dozer and hurt his right shoulder; told his supervisor his arm hurt, not that it was from the job. Never stating anything else, he then went to the doctor on 4/21/04. This is when he states it wasn't getting any better. Safety department received the paperwork from the job site on 4/29/04 to file this MSHA report.

EE STATES HE WAS CLIMBING DOWN FROM BAG HOUSE WHEN HE SLIPPED LANDING ON KNEE DUE TO WATER ON LADDER.

EE STATES WHILE USING A SLEDGE HAMMER TO BREAK ROCKS HE PULLED SHOULDER.

WHILE ATTEMPTING TO ROTATE A MOTOR SHAFT WITH A PIPE WRENCH. THE SHAFT FREE WHEELED, CATCHING HIS HAND BETWEEN THE WRENCH AND HOPPE FRAME. LACERATION RT. INDEX FINGER REQUIRING TWO STITCHES.

EMPLOYEE STATES THAT HE WENT TO STAND UP, AFTER WALKING UNDER CONVEYER HE STOOD UP TOO SOON AND HIT HIS HEAD ON THE CONVEYER, HE WAS WEARING HISHARD HAT.

WHILE INSTALLING A NEW GEAR BOX EE WAS HAMMERING WHILE A CHIVE 2 FT ABOVE HIM ON THE FRAME. HIS LEFT ARM WAS ON TOP OF THE GEAR BOX WHILE HE WAS TIGHTENING THE BOLTS WITH HIS RIGHT HAND. CHIVE FELL ON LEFT WRIST.

EE STATES WHILE SHOVELING UNDER VSI HE PULLED MUSCLES

EMPLOYEE WAS GRINDING OUT DENTS IN A HOOD OF A TRUCK WHEN THE GRINDING WHEEL CAME LOOSE AND HITHIS LEG CAUSING A CUT WITH PIECES OF THE DISC EMBEDDED IN HIS LEG.

EE PICKED UP RAILROAD TIES TO SET ON FORKLIFT WHEN ONE SLIPPED AND SMASHED HIS FINGER.

EE STATES HE WAS CLIMBING DOWN FROM A LOADER AND SLIPPED JAMMING HIS LEFT KNEE.

EMPLOYEE STATED THAT HE WAS CUTTING A DISCHARGE IPIE HE SLIPPED & HIT HIS LEFT LEG WITH A SHARP EDGE.

EE STATED THAT WHLE KNOCKING A TOOTH OFF A BUCKET A CHIP OF METAL CAME OFF THE TOOTH AND WENT INTO HIS LEFT KNEE.

EE STATES THAT WHILE HE WAS CLEANING THE VSI CRUSHER WHICH WAS OUT OF SERVICE FOR A MOTOR RADIOATOR REPLACEMENT AND WHEN THE RADIATOR WAS REPLACED THE MECHANIC JOGGED THE MOTOR AND THE EE CLEA NING THE CRUHSER WAS STRUCK BY THE ROTATING TABLE.

EE WAS IN PROCESS OF CHANGING THE BLOW BARS IN THE IMPACTOR AND THE ROTOR AND BLOW BARS ON ONE SIDE HUNG UP AGAINST THE WALL. A CRANE WAS HOOKED UP TO HELP TURN THE ROTOR AND APARENNTLY WHILE THE CRANE WAS LIFTING AND PRY BAR WAS BEING USEDHIS FOOT SLIPPED DOWN INSIDE AS THE ROTOR TURNED AND IT CAUGHT HIS RIGHT FOOT.

EMPL9OYEE STATS THAT HE DOESN'T KNOW WHEN HE WAS INJURED, BUT IT MAY HAVE OCCURED WHEN HE JUMPED OFF FROM A LADDER. HIS ALLEGED INJURY IS UNDER INVESTIGATION BY THE STATE IDUSTIRAL INSURANCE SYSTEM.

EE STATES THAT WHILE HE WAS WELDING ON A CONVEYOR BELT AND KNEELING HE LOST HIS BALANCE AND HIS FOREARM TOUCHED A HOT WELDED AREA.

EMPLOYEE STATES THAT WHILE PRYING ON SCREEN DECK AND INSTALLING NEW SCREENS, THE PRY BAR SLIPPED AND HIT HIM IN THE JAW.

EE WAS REMOVING ROCKS FROM A JAW CRUSHER AND HIS FINGER GOT CAUGHT BETWEEN TWO ROCKS AND WAS CUT.

EMPLOYEE STATES THAT HE NOTICED NUMBNESS IN HIS FINGERS AND THUMBS AFTER PUSHING ON THE CONTROL BUTTONS FOR THE BELT LOADER GRIZZLEY.

STATES THAT WHEN HE WAS BREAKING LOOSE THE FEED TUBE ON TOP OF A V.S.I. THE LID SLIPPED AND FELL ON TOP OF HIS FEET.

ON 09-16-92 EMPLOYEE REQUESTED TIME OFF FROM WORK TO SEEK MEDICAL ATTENTION FOR A PREEXISTING CONDITION (NON-INDUSTRIAL NECK SURGERY PERFORMED IN 1991) ON 11-05-92 HE INFORMS THE COMPANY THAT HIS WORK HAS AGGRAVATED HIS PRESENT CONDITION

EE STATES THAT WHEN HE WAS RUNNING TO SHUT OF A WATER PUMP AT THE WATER PLANT HE STEPPED IN A SMALL HOLE IN THE GROUND AND STRAINED HIS RIGHT KNEE.

EMPLOYEE STATES THAT WHILE LIFTING A CUTTING EDGE (LEADING EDGE PROTECTOR - 50 LBS) AND PUSHING IT INTO PLACE ON A 988-B FRONT-END LOADER HE STRAINED HIS BACK.

STRAIGHTNING CHUTE WITH SLEDGE HAMMER