AVERY ISLAND Metal/Non-Metal

Employee was hammering a collet pin out of a boom swing pin, missed the pin and smashed middle finger.

Two Production Miners were loading shot in a face. One miner started to feel weak and was unable to catch breath. The loading process was stopped and the ill miner was taken to the Production office where attempts to cool the employee were started.

Employee attempting to open a slide on an air lock door. The employee pinched EE's right hand, at the base of EE's thumb, between the handle of the slide door and the door.

Employee complained of nerve pain in arms after using air and electric chipper for months doing shaft work. An occupation doctor visit triggered a nerve study. The nerve study was positive for carpal Tunnel Syndrome. This was considered compensable due to the nature of the work. This became a recordable injury on the date of surgery.

Employee was driving a bolt with an impact wrench. Brake clean solvent was in the hole and when compressed, combusted and blew the bolt out of the hole. This drove the impact upwards. The employees left hand was on top of the gun. EE's left index finger was mashed in between the gun and the equipment breaking it, requiring surgery.

Louisiana Cat Techs were installing the tilt cylinder on the rear axle. While trying to line up the bores of the frame and the rod of the cylinder, the bearing on the frame was not lined up and was caught. While lining up EE's hand was on the bottom of the cylinder, when cylinder lined up it dropped 3" onto EE's finger. EE had gloves on at the time.

The employee was removing a guard. EE was holding the guard with left hand and struck the guard with a hammer with right hand. The guard dropped down & pinched the small finger on left hand between a block and the handle on the guard. The employee broke small finger on left hand.

EE was removing a drill rod from a drill. EE was holding the drill rod on the very end instead of the middle. When the threads finished the rod fell to the ground jolting EE's left elbow. This inflamed tendonitis in EE's elbow. EE was shown stretches and released to full duty until the injection on 6-13-17.

Employee/contractor was working on a troubleshooting task for approximately 45 minutes to 1 hour on computer in the clearlane building with mine employee/witness. EE passed out/fainted in the clearlane room. The room temperature was warm at an estimated 100-105 degrees. Heat and dehydration were determined to have contributed to the incident.

Employee was cutting belt line with a retractable knife. Employee put themselves in the line of fire by cutting towards wrist and cut themselves needing sutures.

Injured employee was front seat passenger in a four seat UTV personnel vehicle. The driver turned too wide and tipped the UTV over on the driver's side. Injured employee reached across chest with left hand to brace for impact, injuring left shoulder. Did not become recordable accident until 8/23/16

Initial injury occurred on 7/14/15 while employee was stacking 50lb salt blocks on a pallet. After visiting the doctor it was determined that it was just a strain and employee was sent back to work on full duty. On 5/31/16 Employee was shoveling salt at the screen plant. After taking EE to the doctor it was determined that EE has a hernia and was put on light duty.

An employee was using a retractable blade safety knife to cut a tie wrap. EE had the safety knife in right hand. EE was holding a pipe and hose in left hand. The pipe moved and the knife stuck the employee's left thumb causing an approximate 2" laceration on the inside portion. The employee was taken in for medical evaluation, received sutures and released to full duty.

Employee plugged in a golf cart. He tripped over the wire and grabbed onto the top of the golf cart to prevent his stumble. Employee injured right shoulder in the process. At first it was not reportable. He was only given home exercises and told to put heat on it. On 2-16-2016 it became reportable when injections were given and physical therapy was prescribed.

Employee was cutting the banding off of troughing idlers. When the final band was cut the first row of idlers fell off of the pallet striking the employee on the right foot, penetrating the boot behind the steel toe and injuring right big toe. The employee fell to the ground between the stack of idlers and a material handler which was parked aproximately 4' away.

The employee was running the hammer. He was going down steps when his right heel got hooked and he fell forward to the cement and stuck his left hand out to break his fall. His left middle finger was jammed and he received what is referred to as mallet finger that needed to be surgically repaired through outpatient surgery.

1597 Scaling rig ruptured a hydraulic hose which caused a fire. The suppression system shut off the rig and went off as designed. The employee was able to get safely off of the rig and noticed a fire that was burning uncontrollably. Everyone was evacuated safely and the scaler burnt to the ground. The scaling rig was a total loss and the mine was shut down for two days.

An employee was cutting a 1" flex pipe with a safety knife. The knife slipped and cut through the black dot glove and the inside of his middle joint on the middle finger of his left hand. The employee needed sutures to repair the laceration. He was also given a prescription for the pain. The employee was released to full duty on his next shift with no restrictions.

An employee was removing a sling from a fork while standing adjacent to a undercutter bar. The outrigger for the material handler that was holding the bar on a set of blocks was raised. The bar slid off of the blocks landing on the left foot of the employee.

The employee was attempting to close the width of the forks on a 4 wheel drive Gradall Material Handler. He placed his left hand into the pinch point behind the fork and his right hand slipped off the fork. His left middle finger tip was crushed in between the fork and the mast.

Employee was descending a service loader with a filter assembly. The assembly got stuck on the steps and the employees right middle and ring finger tips were snipped off by a pinch point created between the handle and the housing.

Employee was using a 2" ball valve to try and drive out a pin to change out forks on a Gradall Material Handler. The employee missed his target and sliced his left pinky finger open requiring 3 stitches.

Employee was working on a water heater. His right foot got caught on a copper tubing and he tripped. He fell, landing on his right knee, followed by his face and then his hands. He received surface abrasions on his face and right knee and had a stiff neck and back. He was released to full duty. But on January 31,2012 he was taken out of work pending MRI and treatment.

Employee was using a lift assist to stack 50# salt blocks on a pallet. The assist failed and a block was dropped onto the ground. The employee bent at the waist to pick up the block and then pivoted to place the block onto the pallet. While pivoting he felt a pain in his right lumbar. He did not report this until the next day when the pain persisted.

Employee was tramming the 980 loader to the work area and reached down to adjust the seat. He over-reached and his finger went inside the seat suspension. Hitting another bump, the weight of the seat along with his body weight, collapsed the suspension causing it to pinch the middle finger on his right hand.

Employee fell when poorly designed steps failed. Employee ended up with a strained AC joint that needed prescription medication to repair.

Employee was changing a hose on a drill without stopping for breaks or drinking any water. The employee had to be brought to the hospital by ambulance. Test were run which all came back negative and IV's were administered with no prescriptions, just to hydrate. Employee was diagnosed with heat stroke, near syncope and released to full Duty with no restrictions.

Employee was negotiating a corner in a John Deere Gator on a slope underground and the right tires climbed the berm guarding the right rib after turning too short. The Gator turned over on it's side and the employee's left leg was injured in the accident.

While hoisting salt, the South skip dumped the load of salt and one of the pedestals for the dump arms broke. The dump gate opened while it traveled down the shaft and got wedged in the shaft. The damage caused the skip to be changed out.

Employee was walking up entry decline #20 near the #1 crosscut to retrieve survey materials. He slipped on the floor and fell, fracturing both bones in his lower right leg.

Employee was holding two boards (for alignment purposes) to be nailed together with air nailer. Hands were approximately 18" from point to be nailed. Air nailer double shot and the second nail struck employee in the left index finger between the hand and first joint in finger. Nail was removed from finger by the doctor and employee returned to work. Nail did not contact bone.

Crew was gathering tools and materials to start job. EE was returning to tool trailer for additional tools when he walked to close to an elevator cover which had been previously removed and placed on the ground. As ee passed by the cover, the flange on the cover caught on his pants, cutting pants and right leg.

Employee had no particular point during his shift where he felt any pull or pain. He noted that he was pulling up on a wrench all night while changing clips in the production shaft. He went straight to sleep after leaving work and woke with the pain. He has been diagnosed with a incarserated hernia that will be surgically repaired on Thursday January 21st.

Employee ran a John Deer Gator XUV into a MTI truck. Employee's face struck the ROPS on the Gator and sustained lacerations above and below right eye, busted teeth out of mouth, punctured right cheek and fractured portions of his upper jaw.

EE was bitten by a spider that came out of a pallet on Monday 11/02/2009. He did not want any medical care. It progressively got infected and he finally agreed on Thursday 11/05/09 to be seen by a physician. The Doctor prescribed a oral antibiotic and released him to full duty with no restrictions.

Bolting intersection with Fletcher mechanical bolter. Operator climbed down from the cab, slipped on the ground and strained his left knee.

Employee was replacing bolts in gallery structure. Driving old 3/4" bolts out of wood structure using new 3/4" bolts as a punch. As he was striking bolt with sledge hammer, his left elbow struck an existing bolt. Bruised left elbow.

employee and partner were changing the oil on a speed reducer for belt drive # 204. After completing task, they were cleaning up the work area. They attempted to lift a 50 lb Jabsco pump into the back of a Gator, as EE bent down and gripped the handle, he felt something pop in his lower back.

Employee opened door to check weather. He leaned on a removeable handrail that was not seated properly and it gave way, causing him to fall 4' to the ground, face first.

Employee was removing troughing rollers on # 210 belt in order to change the rails. While removing the rollers, he pinched his left ring finger between the roller and the rail.

On 11/16/08 two supervisors entered the mine via the production shaft. When they came out of the airlocks they noticed there was a burnt smell in the air. They noticed Three John Deere Gators and One Kawasaki Four Seater Mule had burned completly to the frame. The fire started and burned when no one was in the mine, and was caused by an electrical short

Brakes were not holding and functioning properly on the secondary hoist. We evacuated the mine, repaired brakes on the secondary hoist around 8:45 am.

The brakes are not holding on the steam hoist. Hoist will be taken out of service until brakes are repaired. This will not affect our facility, we still have two shafts up and running to get employees in and out of the mine.

Employee was walking down a set of stairs in the surface mill building. Upon reaching the last tread on the staircase the employee's right heel on his boot became stuck and caused employee to fall forward and land on his right knee. Employee tore his right quadricep tendon in his knee.

Employee was moving a fireproof filing cabinet in the HR office. After moving the cabinet the employee stated he felt pain in his groin area.

Employee stepped off the concrete slab in back of the block press and his right knee popped. Slab was approximately 8" in height.

Employee worked throughout the Mill Building, walking up and down the stairway replacing fire extinguishers, much of the shift. Near the end of the shift, employee was loading a large box of paper trash onto a pallet. While lifting the box, the load shifted and box started coming apart.

Employee was working on barge dock loading empty barges. Employee was bending over to pick up an accudraft box which weighs 5-10 lbs. He stated when he stood back up he felt a sharp pain in his back. Took employee to get examined on 11/16/07 doctor did not prescribe any medication but did place EE on light duty for a week. EE's personal doctor excused him from work on 11/21/07.

New, first day of labor. Employee was working with 2 miners loading a face with Anfo. Work started at 9:30am. After running the hose for the first heading, employee complained of chest pains, sweating, nausea. He was removed from work, given oxygen, removed from the mine, taken to the hospital, treated for dehydration and checked for cardio-vascular issues. None found.

At 8:30 pm power was lost to the mine. Evacuation called. MSHA was notified. After evacuation completed, electrician and supervisor entered the mine and discovered the 4160 volt cable had been damaged in an abandoned area of the mine, by a roof fall. The cable was disconnected, re-routed and repaired. This took place on the 500' level.

Employee driving mine tractor turned into vehicle passing him. Following day employee complained about discomfort in shoulder and lower back. Employee examined by Dr and given non-prescription medication. Employee returned to full duty with recomendation to avoid any heavy lifting for a week. *possible over-reporting (RTW with 5 days restricted)*

Employee had been standing on a ladder welding the frame of a CAT loader of which he had also been welding on at different times the week prior. Around the time of the illness, he complained of dizziness and nausea. The determined result was that employee had suffered a heat stroke due to dehydration and elevated temperatures.

3 employees were installing a 120lb stainless steel chute. After lifting the chute EE felt a twinge in his lower back. Following day 4/3/07 he was taken to the clinic, x-rays were negative, diagnosis was a Lumbosacral Strain, Mobic a nonsterodial anti-inflammatory drug was prescribed. The employee returned to work with restrictions.

Employee was lubricating the slide cylinders with an oil can that operates the mold box on the salt press. His left hand became crushed when the mold box raised and caught his left hand betwee n the mold box and the header plate.

Oldenburg Scaler in service since Jan. 05 caught fire while scaling in S-27 1600' level. The fire was probably caused by a hydraulic leak ingnited by normal operating temps of the engine. The scaler was a total loss.

8/15 employee descending stairway placed foot on the floor felt a pain in his right knee. 8/16 taken to medical clinic for precautionary x-rays found negative for acute injury. 9/29 results of an MRI showed tear of the posterior horn on the meniscus. 10/20 surgery occurred to repair injury, was off LTA 8 days until 11/1/06 returned to work with restrictions.

Employee was dismounting a Galion crane at 204 belt head in the 1300' level. He slipped and fell between the tire and cab, causing an abrasion and cut to his right front leg. It became a medical aid on 3/15/06 when the cut became infected. Dr. cleaned out the infection and prescribed antibiotics.

Employee had removed worn piece of belt skirting 16' x 8". Employee was feeding the skirting over a rail when he felt a 'pop'. Employee continued work pain free, but the area was swollen the next shift. Took him to Doctor, examination showed tear in pulley of tendon right hand middle finger. Surgery repaired 8/19/05 released with restrictions for 2 weeks.

Employee was cutting plastic tie wrap with razor knife; knife slipped and cut employee on left palm of hand.

EMPLOYEE HAD SHOVELED SALT OFF OF TOP OF CONVEYOR CHUTE. EMPLOYEE SLIPPED ON SALT SHOVELED AND TWISTED LEFT KNEE

employee working with contractor installing beams for overhead crane in new shop.contractor moved beam without communication, pinched hand. Saw physician numerous times, put on restricted duty 7/13/05 for torn ligament discovered thru MRI.

OPERATOR CLEANING FACE ON 1600'LEVEL OF MINE. A NON-FATAL FIRE STARTED ON LOADER THAT COULD NOT BE EXTINGUISHED, THE MINE WAS EVACUATED. FIRE WAS LATER DETERMINED TO BE CAUSED BY ELECTRICAL COMPONENTS.

EE was dismounting a front end loader in dark part of mine and stepped down onto a small chunk of salt, twisting left ankle.

Employee was using 21" step ladder to change hose on boom of material handler. As he stepped off of small ladder it sid out from under him causing him to lose balance and hurt his foot.

WHILE PLACING 4 X 8' 3/8" STEEL PLATE ON ASSIGNED JOB, FINGER GOT PINCHED. EMPLOYEE USED HIS LEFT HAND TO LIFT STEEL OFF OF HIS FINGER. EE FELT A MUSCLE PULL IN HIS LOWER BACK.

Employee was installing roof bolt through metal webbing, attempted to use roof bolt to pull slack in webbing prior to inserting in drill hole. He felt pain in right arm.

EE COMPLAINED HIS ARM WAS HURTING AFTER USING HAMMER (5/19/04). ON 6/8/04 EE REQUESTED TO SEE A DOCTOR. THE DOCTOR FOUND NOTHING WRONG. ON 7/1/04 EE WAS REFERRED TO A PHYSICAL THERAPIST. EE WAS GIVEN THERAPY AND TOLD TO AVOID USING A HAMMER ON THE JOB (RESTRICTED USE OF HAMMER, BUT ALLOWED ALL OTHER DUTIES).

EE WAS IN MAN BASKET ATTACHING J BOLTS ON ROOF OF MINE. OPERATOR ATTEMPTED TO TRAM TO NEW LOCATION WITH BASKET ELEVATED. EQUIPMENT TILTED CAUSING EE TO FALL AGAINST HANDRAILING.

EMPLOYEE TRIPPED ON METAL STAIRWAY AND CUT HIS FINGER ON METAL STEP GRATING

SUPERVISOR WAS CHECKING ESCAPE LADDER IN 1300' BENCH, WALKING AND TRIPPED ON CHUNK OF SALT. DISLOCATED RT. INDEX FINGER.

A BATTERY ON AN ANFO LOADER SHORTED OUT CAUSING EMPTY BAGS OF ANFO TO CATCH FIRE, CAUSING AN EVACUATION OF THE MINE.

EMPLOYEE LIFTING 50 LB BAG ANFO, FELT PAIN IN LEFT ARM, ELBOW AND WRIST.

WHILE THE INJURED AND ONE OTHER PERSON WERE DISMANTLING A CONVEYOR AND WORKING FROM A MAN BASKET THE INJURED CAUGHT AN OBSTRUCTION WITH HIS FOOT AND TEMPORARILY LOST HIS BALANCE CAUSING HIM TO TWIST HIS RIGHT ARM.

EE OPERATING MOBILE CRANE FELT PAIN IN LOWER ABOMEN AREA WHEN APPLYING BRAKES. DIAGNOSED WITH SMALL HERNIA. DECIDED TO DELAY ANY SURGERY. ON 1-15-04 HAD LAPSOPIC SURGERY AND ALLOWED TO RETURN TO WORK WITH RESTRICTIONS.

EMPLOYEE WAS WALKING WHEN HIS RIGHT FOOT SLIPPED ON THE SMOOTH SALT SURFACE CAUSING LEFT FOOT TO TWIST. THIS ACTION CAUSED A HAIRLINE FRACTURE TO HIS LEFT LEG NEAR THE ANKLE.

NORTH PRODUCTION SKIP MOTOR COUPLING DETACHED, CAUSING SKIP TO KICK OFF ON TIME, GOT STUCK IN SHAFT AT 227 FOOT LEVEL. SKIP LOWERED BACK DOWN TO 500' LANDING USING DISK BRAKES WITH A SECODAR Y AND TERTIARY DISK AND BAND BRAKES AS BACK UP.

GETTING OFF OF MATERIAL HANDLER. CAP LAMP CORD HUNG UP ON STEERING WHEEL, CAUSING EMPLOYEE TO SLIP AND FALL.

WHILE HOISTING PERSONNEL AT SHIFT CHANGE, A POWER SURGE FROM A LIGHTENING STORM KNOCKED OUT ELECTRICAL POWER TO THE HOIST, BURNING FUSES & TRAPPING 8 PERSONNEL IN SKIP, 10' BELOW LANDING, FOR APPROX. 3 HOURS.

EE WAS REPLACING A 7 1/2 HP ELECTRIC MOTOR ON A ROTEX SCREEN. EE ATTEMPTED TO REMOVE THAT MOTOR THROUGH A SMALL OPENING AND GOT HIS FINGER PINCHED BETWEEN THE MOTOR AND"I" BEAM.

EE USING SAFETY KNIFE TO TRIM FACE SHIELD TO FIT FACE SHIELD FRAME. MADE CUT TOWARDS SELF, CUT LEFT WRIST. INJURY REQUIRED 5 STITCHES.

EE WAS CUTTING STEEL ON AIRSHAFT HEADFRAME & FELL THROUGH GRATING 32 FT TO THE GROUND. FULL BODY HARNESS WAS IMPROPERLY TIED OFF. SUFFERED CONCUSSION, CUTS, & DISLOCATED SHOULDER.

EE ATTEMPTING TO CUT TIE-WRAP WITH KNIFE. KNIFE BLADE HIT BED OF VEHICLE ABRUPTLY STOPPING CAUSING EE'S HAND TO HIT KNIFE BLADE, CUTTING FINGER.

EE WAS ACCESSING A WORK DECK THRU A MAN DOOR. THE DOOR WAS BUMPED BY ANOTHER EE CAUSING VICTIM'S RIGHT HAND TO BE PINCHED IN DOOR & DOOR FRAME.

HOIST OPR WAS SENDING MATERIAL INTO MINE. APPROACHED LANDING TOO FAST. SKIP BOTTOMED OUT IN SUMP BEFORE STOPPING CAUSING MINOR DAMAGE TO SKIP BOTTOM. SPEED AND WEIGHT OF LOAD PREVENTED SKIP FR OM STOPPING BEFORE GOVERNOR OVERSPEED TOOK OVER AND BEGAN STOPPING SKIP.

EE STOOD TOO CLOSE TO MOVING VEHICLE & HAD RIGHTFOOT BROKEN BY REAR WHEEL.

EE INSTALLING CYLINDER ON DRILL RIG. FAILED TO BLOCK HEAD. PART OF DRILL HEAD FELL AND CUT FINGER.

EE ASCENDING STEPS FROM SHAFT POCKET AREA. TOOLS AND EQUIP0MENT REQUIRED MULTIPLE TRIPS. EE ATTEMPTED TO THROW OBJECT UP STAIRWAY. OBJECT HIT BEAM, FELL BACK INTO POCKET AREA, HITTING EE.

EE WAS REMOVING GUARD ON LEFT SIDE OF ENGINE COMPARTMENT ON DRILL RIG. FELT BURNING SENSATION IN LOWER BACK.

EE WAS CLEANING TAIL PULLEY AREA OF ONE CONVEYORAND A CHUNK OF SALT FELL OFF OF ANOTHER CONVEYORBELT, STRIKING HER RIGHT SHOULDER.

EMPLOYEE WORKING ON ONE CRUSHER. ANOTHER ADJACENT CRUSHER WAS STARTED UP. CHUTE TO ANOTHER CRUSHER WAS CHOKED CAUSING SALT SPILLAGE. EMPLOYEE ALLEGES SALT STRUCK HIM ON HARD HAT AND SHOULDER. DID NOT SEEK MEDICAL ATTENTION UNTIL 8/8/01.

UPON DRILLING PRELIMINARY HOLE DEPTH, DRILL HIT VOID WHEN DRILLING UP. THIS CAUSED DRILL TO HIT ROOF CAUSING A SMALL SALT SLAB TO CRACK AND FALL ON LEFT INDEX FINGER, APPARENTLY CAUSING A LACE RATION.

EE WAS USING PIPE WRENCH TO CHANGE OUT PIPE ON SPRINKLER SYSTEM. USED UPPER BODY TO ASSIST IN PUSHING ON WRENCH. FRACTURED SEVENTH RIB.

EE USING PUNCH TO REMOVE BOLT FROM SHEAVE WHEEL. SMALL PIECE OF BOLT BROKE OFF AND PENETRATED EE S LEFT LEG AT KNEE.

EMPLOYEE ATTEMPTING TO STRAGHTEN UP PILE OF PALLTS USING SCALING BAR. SCALING BAR SLIPPED CAUSING EMPLOYEE TO FALL.

THE BUSHING ON THE DUMP GATE SHAFT FOR THE NORTH SKIP BROKE CAUSING THE PRODUCTION SKIP TO JAM.

EMPLOYEE CLIMBING DOWN STEP OF HAULAGE TRUCK, FOOT SLIPPED OFF BOTTOM STEP CAUSING HER TO TWIST HER RIGHT KNEE WHEN HER FOOT HIT THE GROUND.

EMPLOYEE USING SLEDGE HAMMER TO REMOVE PIN. FELT PAIN IN ELBOW.

MECHANIC USING METAL PUNCH TO REMOVE PIN ON UNDER CUTTER CHAIN. POINT OF PUNCH BROKE OFF AND HIT ANOTHER MECHANIC ON CHIN. CAUSING A SMALL CUT ON CHIN ONE STITCHES REQUIRED.

OPERATOR ERROR CAUSED SKIP TO STOP SUDDENLY. SUDDEN STOP CAUSED INDIIVIDUAL TO STRAIN HIS BACK.

AT APPROX 7AM ON JULY 6, 2000, THE HOIST OPERATOR FOR THE PRODUCTION HOIST NOTICED A BROKEN BOLT ON THE HOIST BRAKES. AS A PRECAUTIONARY MEASURE, THE MINE WAS EVACULATED AND BOLT REPAIRED. T HE REPAIR WAS COMPLETED AT 11:15 AM AND WORK WAS RESOMED.

EE ATTEMPTING TO REMOVE U JOINT ON UNDERCUTTER, FAILED TO TAKE RETAINING SPRING OFF. ANOTHER EE USED HAMMER IN ATTEMPT TO REMOVE U JOINT. JAMMER GLANCED OFF AND HIT EE ON FINGER, BREAKING BONE AND INFLICTING BAD CUT.

WHILE HOISTING SALT TO THE SURFACE, THE DUMP GATE ON THE SOUTH SKIP PREMATURELY OPENED AT THE -500' LEVEL DAMAGING THE SKIP AND APPROX. 100' OF SHAFT.

EMPLOYEE USED IMPROPER LIFTING TECHNIQUE WHILE LIFTING STRETCHER HURTING LEFT KNEE. EMPLOYEE ALLOWED TO RETURN TO WORK ON REGULAR DUTY. KNEE CONTINUED TO CAUSE DISCOMFORT AND ON 5/5/00 HAD MINOR OUT-PATIENT SURGERY. ALLOWED TO RETURN TO WORK ON RESTRICTED DUTY.

EE WAS GETTING OFF OF SERVICE TRUCK AND TWISTED ANKLE/LEG ADN PRODUCED INFLAMMATION TO SCIATICA NERVE. INITIALLY RETURNED TO REGULAR DUTY. CONDITION NOW AFFECTING DISK IN LOWER BACK. ON 5-5-00 , EE WAS PLACED ON RESTRICTED DUTY.

EMPLOYEE WAS DIAGNOSED HAVING A HERNIA. EMPLOYEEALLEGES IT MUST HAVE HAPPENED SOMETIMES DURING THE 12 HOUR SHIFT ON 10-15-99, BUT COULD GIVE NO EXACT LOCATION OR INCIDENT.

EE WORKING IN SHOP. IT IS BELIEVED THAT WHEN LOCAL VENTILATION FAN MOVED, MOVE CAUSED SALT DUST TO BLOW INTO EE'S EYES.

EE SLIPPED ON SPILLED SALT ON BARGE WALKWAY WHILE LOADING BARGE.

EE WAS ENTERING MINE USING PRODUCTION HOIST. HOIST WENT INTO ESTOP MODE WHEN D.C. MOTOR LOOP CONTACTER AUXILIARY SWITCH FAILED TO STAY CLOSED. SUDDEN STOP CAUSED EE TO FALL, BRUISING LEFTY KNE E AND ANKLE.

EMPLOYEE USING HAMMER TO INSTALL LINK ON CRUSHER CHAIN, SMALL METAL BROKE OFF OF HAMMER AND LODGED IN ENPLOYEE'S FINGER.

EE NOTICED SOMETHING IN EYE.. INITIAL INVESTIGATION REVEALED NOTHING, BUT FOLLOW UP EXAMINATION REVEALED SMALL OBJECT. EE ALLOWED TO RETURN TO FULL DUTY

EMPLOYEE WAS STACKING EMPTY BAGS ON RIG TABLE. ONE BAG FELL BETWEN OPERATOR SET AND TABLE. WHEN EMPLOYEE REACHED TO RETRIEVE BAG, PULLED MUSCLE IN BACK.

EMPLOYEE RECEIVED INJURY TO BACK ON 10-26-98. RETURNED TO WROK AT REGULAR DUTY. CONTINUED PAIN CAUSED RE-EXAMINATION. EMPLOYEE FOUND TO HAVE RUPTURED DISC. SURGERY ON 2-1-99. EMPLOYEE CON TINUED WORKING UP UNTIL DATE OF SURGERY.

EE WAS MOVING A LARGE PULLEY ONTO A WORK PLATFORM. PULLEY SHIFTED, CUTTING HIS FINGER, REQUIRING STITCHES ON INJURY.

MECHANIC STEPPED OUT/OFF OF TRACTOR AT JOB SITE. HE STEPPED ON A CHUNK OF SALT SPRAINING HIS LEFT ANKLE.

EE ALLEDGES T0 HAVE HURT BACK ON 17TH WHILE LOADING 50PD BAGS OF ANFO. DID NOT IMMEDIATELY REPORT ACCIDENT

EE WAS ASSIGNED TO ASSIST OPERATOR IN THE REMOVAL OF HARD SALT ON FEEDER. EE REMOVED CAP ON SALT CLEAN OUT SPOUT AND STUCK HIS HAND IN MOVING SCREW CONVEYOR, WITHOUT LOCKING OUT EQUIPMENT.

EE WAS ATTEMPTING TO PUSH A TOOL BOX WITH HIS KNEE AND SLIPPED ON FLOOR OF TRUCK BED. EE ATTEMPTED TO STOP HIS FALL BY GRABBING METAL CORSS PIECE IN TRUCK.

EE WAS LAODING A BULK TRUCK. THE HAND WHINCH USED TO RAISE AND LOWER CHUTE MALFUNCTIONED AND JAMMED EMPLOYEE'S HAND AGAINST HANDLE. ACCIDENT NOT REPORTED UNTIL 7-6-98.

EE WAS WALKING TO WATER COOLER AND STEPPED ON CHUNK OF SALT.

EMPLOYEE WAS LIFTING TOOL BOX INTO REAR OF JEEP. IN DOING SO, EMPLOYEE LIFTED AND TWISTED AT SAME TIME.

TWO EES WERE SCALING FROM BASKET OF 448 CONDOR CRANE. SCALE DID NOT FALL AS INTENDED AND STRUCK BASKET AND ONE EE ON ARM.

EMPLOYEE WAS UNLOADING A STEEL BARREL THAT HAD THE TOP CUT OFF TO USE STORE PARTS. BARREL HAD ONE SMALL SHARP EDGE THAT CUT EMPLOYEES FINGER.

EE WAS PUSHING TOOL CART IN MINE SHOP AND SLIPPED ON SMOOTH SPOT ON FLOOR

EMPLOYEE REMOVED HOT RADIATOR CAP TO CHECK COOLANT. EMPLOYEE THOUGHT RADIATOR HAD COOLED OFF.

EE WAS GRADING AREA ADJACENT TO WELDING SHOP WITH BOXBLADE. HEAVY RAIN HAD WASHED OUT AND EXPOSED A SUPPORT STRUCTURE THAT WAS PLACED AT GROUND LEVEL TO SUPPORT PORTABLE WELDING CURTAINS. BOXB LADE STRUCK STRUCTURE CAUSING TRACTOR TO COME TOABRUPT STOP. EE HIT STEERING WHEEL.

EE PULLED MUSCLE IN BACK WHILE SCALING LEDGE OF BENCH IN ROOM T-28.

EMPLOYEE WAS CLIMBING UP A 3 STEP LADDE RON GRADALL SCAILIGN RIG, AND PULLED A MUSCLE IN HIS SHOULDER.

EMPLOYEE FAILED TO LOWER DUMP ON DUMP TRUCK. DUMP JAMMED ON ROOF OF MINE CAUSING CAB TO ELEVATE. WHEN DUMP UNHOOKED, CAB FELL TO GROUND AND FALL TO GROUND. THIS ACTION CAUSED EMPLOYEE TO RECEI VE BRUISING INJURIES.

EMPLOYEE COMPLAINED OF FOREIGN OBJECT IN LEFT EYE. NOTHING COULD BE FOUND AT HOSPITAL. SUSPECT EYELASH, SINCE FIRST AID ATTENDENT AT MIEN DID REMOVE EYELASH WHEN EYE WAS INITIALLY CHECKED.

AS EMPLOYEE WENT TO DISMOUNT HIS LOADER, HE ATTEMPTED TO PICK UP HIS MINER'S BELT. THE SELF RESCUE UNIT ON THE BELT WAS STUCK BEHIND THE SEAT. WHEN THE EMPLOYEE JERKED ON THE BELT TO FREE IT, HE PULLED A MUSCLE IN HIS RIGHT SHOULDER.

EE WAS HITTING ON UNDERCUTTER CHAIN BLOCK TO ALIGN WITH THE PIN. SMALL PIECE OF METAL BROKE OFF AND CUT INDIVIDUAL ON LEFT HAND. CUT STITCHES.

EMPLOYEE ALLEGES TO HAVE CUT HIS FINGER WHILE ADJUSTING A BROKE REAR VIEW MIRROW ON MINE TRUCK.

AT 3:20 AM ON 1-9-97 THE ROOF INTERSECTION ON 0-26 ON THE 1300' LEVEL OF THE MINE, FAILED AND FELL 90', DESTROYING P&H CRANE #445. CAUSE OF INCIDENCE UNDETERMINED AT THIS TIME.

GROUTER FOREMAN, DURING A ROUTINE INSPECTION OF A GROUTER DRILLING LOCATION, ALLEGES TO HAVE SLIPPED ON A BOLT, AND FELL LANDING ON HIS SELF-RESCUE UNIT, INJURING HIS HIP. INJURY NOW REQUIRES THERAPY.

EMP WAS JUMP STARTING A LOADER. FELL OFF LOADER (2 FEET) ON CHUNKS OF SALT, SCRAPING HIS LEFT ARM. ONE LACERATION REQUIRED STITCHING.

HEE WAS CLIMBING ONTO SCALING RIG TO CHANGE FUEL FILTER. UPON REACHING DECKING, EE SLIPPED, FELL NINE FEET.

EE WAS OPENING FLOW GATE ON OVERSIZE SALT SHUTE. DID NOT EXPECT SHUTE TO OPEN EASILY. SUDDEN OPENING CAUSED EE TO CUT FOREARM ON SHARP EDGE.

EE WAS STRIKING LATCH PIN WITH A HAMMER, ON AIR LOCK DOOR, WHICH HAD GOTTEN BENT, IN AN ATTEMPT TO OPEN DOOR. BOLT BROKE OFF, STRIKING AND CUTTING EE ON CHIN.

EMPLOYEE ASSISTIN GIN REPAIR OF 400 FOOT WATERLINE IN BOREHOLE BETWEEN 900 FOOT AND 1300 FOOT LEVELS OF MINE. 280' OF PLASTIC PIPE BROKE LOOSE. FALLING ON WORK PLATEFORM, SHATTERING AND CUTT ING EMPLOYEE ON HEAD.

EMPLOYEE ASSISTIN GIN REPAIR OF 400 FOOT WATERLINE IN BOREHOLE BETWEEN 900 FOOT AND 1300 FOOT LEVELS OF MINE. 280' OF PLASTIC PIPE BROKE LOOSE. FALLING ON WORK PLATEFORM, SHATTERING AND CUTT ING EMPLOYEE ON LEG AND HIP.

EMPLOYEE WAS GETTING OUT OF TRUCK,SLIPPED ON SLICK SALT, HITTING HIS JAW ON VEHICLE, KNOCKING OUT THREE TEETH. EMP DID NOT SEEK MEDICAL ATTENTION UNTIL 9-21-95.

EMPLOYEE WAS CUTTING SMALL PIECE OF WOOD ON TABLE SAW.WITHOUT HAVING GUARD IN PLACE.WOOD JAMMED AND KICKED BACK,CAUSING TWO FINGERS ON LEFT HAND TO COME IN CONTACT WITH BLADE.

EMPLOYEE WAS CLIMBING OUT OF SCALING BASKET, WHEN HE STEPPED DOWN FROM LAST RUNG, HE FELT A PAIN IN HIS RIGHT KNEE.

EE WAS USING A KNIFE TO CUT TIE STRAP. THE KNIFE SLIPPED AND EE STABBED HIMSELF IN LEFT HAND.

AIR SHAFT HOIST EXPERIENCED ELECTRICAL PROBLEMS THAT AFFECTED COMPUTER CONTROLS. RE-PROGRAMED COMPUTER.

EMPLOYEE WAS REARRANGING BAGS ON TOP OF AUTOMATIC PALLETIZER. SITE OFFERED VERY RESTRICTED MOVEMENT. EMPLOYEE CONTINUED HAVING PROBLEMS WITH BACK, AND ON 2-24-95, DR TOOK HIM OFF OF WORK.

SALT BUILD-UP ON GUIDE CABLES CAUSED SKIP TO HANG UP ABOUT TWO THIRDS OF WAY DOWN SHAFT. MINE EVACUATED UNTIL CONDITION CORRECTED.

PIECE OF DEMOCITION CONCRETE FELL ON EE S FINGER.

THREE EMPLOYEES WERE MOVING DISMANTLED PORTION OF MILL BUILDING 12X112X10FT BEAM AREA WAS WET & MUDDY DUE TO RAIN BEAM SLIPPED &SMASHED RT FOREFINGER OF EMPLOYEE

EMPLOYEE WAS DRIVING HIS LIFT TRUCK NEXT TO WAREHOUSE, WHEN SOMETHING FLEW INTO HIS RIGHT EYE.

BOLTS ON SCROLL WHEEL PRODUCTION NORTH SHIP BROKE JAMMING SKIP IN DUMP SCROLL ON SURFACE. MINE PERSONNEL EVACUATED FROM MINE, SCROLL WHEEL REPAIRED, SKIP TESTED AND PLACED BACK IN OPERATI ON AT 10:50 PM.

WHILE STANDING ON 2ND FLOOR [NOT TIED OFF], HE PULLED A BOARD UP FROM THE FLOOR THEN BACKED UP &FELL OFF EDGE OF FLOOR TO LOWER LEVEL.

EMPLOYEE STARTED HAND HELD GRINDER PRIOR TO PUTTING ON FACE SHIELD

THE BUILD-UP ON CONCRETE OF SALT WATER RUNNING FROM THE SHAFT & SLOWLY WORKED LOOSE SALT CAUSING IT TO FALL HITTING THE BACK OF EMPLOYEE'S HEAD & NECK.

WOODEN FLOOR BOARD BROKE CAUSING EMPLOYEE TO FALL APPROX 10FT CUTTING HEAD & SCRAPING BACK & ARM

EE WALKED IN WATER THEN CLIMBED ON WOODEN BOARDS& SLIPPED APPROX. 5' & TWISTED HIS ANKLE.

EE WAS DISMOUNTING A TRACTOR, STEPPED ON A CHUNK OF SALT AND SPRAINED HIS ANKLE EE INITIALLY WAS RETURNED TO WORK ON REGULAR DUTY 7-1-94. DR PLACED HIM ON RESTRICTED DAY.

AT APPROX. 4:00 AM, ONE OF THE TWO BLOWER COOLER FANS ON THE PRODUCTION HOIST BURNT. THE MINE PERSONNEL WERE EVACUATED TO THE SURFACE USING THE AIR SHAFT. THE FAN WAS REPLACED AND MINE PERSONN EL RE-ENTERED THE MINE AT 8:00 AM.

EE ALLEGES TO HAVE CONTACTED DERMATITIS FROM HIS EE AS A MECHANIC, CHOSE TO EXERCISE RIGHT AND BUMP INTO WATCHMAN CLASSIFICATION. DO NOT KNOW WHAT SUBSTANCE IF ANY ON THE JOB THAT CAUSED CONDI TION.

EMPLOYEE WAS SERVICING A LOADER. AS HE WALKED AROUND THE EQUIPMENT, HE STEPPED ON A SMALL CHUNK OF SALT AND TWISTED HIS ANKLE, RESULTING IN A FRACTURE TO RIGHT ANKLE.

EMPLOYEE ATTEMPTED TO MOVE LARGE LOADER TIREUSING IMPROPER SLINGING METHOD. SLING SLIPPED, CATCHING AND SMASHINGEMPLOYEE'S FINGER BETWEEN TIRE AND SLING.

WET GROUND.

EMPLOYEE'S FOOT SLIPPED OFF OF LADDER RUNG, CAUSING EMPLOYEE TO LOSE BALANCE, FALL, & BRUISE RIGHT HIP.

EMPLOYEE WAS USING A CHISEL TO INSTALL CONNECTING LINK ON DRILL RIG. SMALL PICE OF METAL CHIPPED OFF AN FLEW UNDER SAFETY GLASSES, INTO EMPLOYEE'S EYE.

WHEN BRINE PUMP WAS STARTED, PRESSURE CAUSED FOOT VALVE TO JUMP UPWARD. EMPLOYEE MADE ATTEMPT TO HOLD VALVE DOWN WITH HIS FOOT. AT SAME TIME ANOTHER EMPLOYEE RELEASED PRESSURE CAUSING INSURED TO LOOSE BALANCE & FALL.

EMPLOYEE WAS USING A 1/2" DRIVE RATCHET WRENCH. THE WRENCH SLIPPED CAUSING THE EMPLOYEE TO FALL AGAINST CONVEYOR BELT.

EMPLOYEE WAS CONDUCTING MONTHLY BLEEDING OF FIRE SPRINKER SYSTEM.AT ONE LOCATION THE WATER PRESSURE CAUSED THE BLEEDER LINE TO UNSCREW THE WATER PRESSURE TO BE MISDIRECTED STRIKING THE EMPLOYE E BEFORE HE COULD MOVE OUT OF THE WAY.

A 6 FOOT SECTION OF GUIDE BEAM BROKE LOOSE AND FELL DOWN THE SHAFT. THE SHAFT WAS INSPECTED AND THE GUIDE BEAM WAS REPLACED.

WORKER WAS USING A UTILITY KNIFE WHICH SLIPPED AND CUT WRIST.

CARELESS DESCENT FROM LADDER ON HAULAGE TRUCK.

DECKHAND WAS STANDING ON BARGE COVERS AND THE TUG BOAT TRIED TO OPEN THEM. THEY WOULD NOT OPEN, SO HE PULLED ON IT AGAIN A LITTLE HARDER AND IT MADE THE BARGE MOVE AND THE MAN FELL INSIDE THE BARGE. HE BRUISED HIS HIP AND FRACTURED HIS LEFT FOOT.

WAS CUTTING RAFTER WITH HANDSAW. NEAR COMPLETION OF CUT, BOARD BROKE, CAUSING HAND SAW TO SWING FREE, CUTTING EMPLOYEE ON LEFT ARM.

INJURED WAS REMOVING TRANSITE SHEETS OFF OF 4TH FLOOR MILL BUILDING. HE AND ANOTHER MAN WAS CARRYING A SHEET OF TRANSITE AND WALKING ON A SHEET OF PLYWOOD TAHT WAS COVERING A HOLE IN THE ROOF . HE STEPPED OFF THE SHEET OF PLYWOOD AND THE TRANSITE GAVE WAY AND HIS FOOT WENT THROUGH. HE HAD A SAFETY HARNESS AND WAS TIED OFF AT THE TIME.

55013LEGES HE HAD SLIGHT PAIN IN HIS BACK UPON ARRIVAL AT WORK BUT PAIN GOT SEVER AFTER CLIMBING UP AND DOWN GRADAL SCALING RIG A FEW TIMES.

46595 EMPLOYEE WAS ON MOVIE LOCATION ATTEMPTING TO CLIMB OUT OF A BOAT ONTO A OLD ABANDONED PORTION OF BAGRE WALK-WAY SUPPORT STRUCTURE GAVE WAY CAUSING EMPLOYEE TO FALL INTO WATER & FX RIGHT 15235

HOIST REPORTED HAD BRAKES WERE NOT SET OR IT WAS RELEASED

THE PRODUCTION HOIST BREAKS WOULD NOT RELEASE, CAUSING THE PRODUCTION HOIST TO BE INPOERATIVE, THUS MAKING THE PRIMARY ESCAPE SHAFT USELESS. ALL PERSONNEL WERE EVACUATED FROM THE LEVEL AND MSH A NOITFIED. THE SOLID STATE RELAY WAS CHANGED AND HOIST BECAME OPERATIVE AT 3:00PM

TWO EMPLOYEES SENT TO CLEAN UP OLD SCRAMBLER AREA. WHEN EMPLOYEES PICKED UP OLD TURN-TABLE, WHICH WAS PLACED OVER OPENING IN FLOOR, INJURED EMPLOYEE WALKED INTO HOLE IN FLOOR AND FELL 14 FEET TO NEXT FLOOR BELOW.

THERE WAS POWER FAILURE TO THE MINE ON 12-01-91 AT 6:00 PM. A DECISION WAS MADE TO EVACUATE THE MINE AT 6:15 PM WHEN THE HOIST OPERATOR WENT TO POWER UP THE AUXILLIARY POWER UNIT, IT WOULD NOT WORK BECAUSE THE COMPUTER HAS LOST ITS MEMORY. THE COMPUTER WAS RE-PROGRAMMED AND MINE EVACUATED AT 7:35 PM.

EMPLOYEE WAS PRYING BOARDS OFF OF OLD BIN, WHILE ON STEP LADDER. BOARD CAME LOOSE, FELL STRIKING EMPLOYEE ON RIGHT ARM. LARGE SPLINTER GOT LODGED IN EMPLOYEE'S ARM. EMPLOYEE COULD NOT MOVE OUT OF WAY IN TIME.

EMPL WALKING ON DECKING AT NEW BARGE RAMP.SECTION OF DECKING GAVE WAY CAUSING EMPL TO FALL AND DISLOCATE LEFT SHOULDER.ACCIDENT CAUSED BY IMPROPER CONSTRUCTION OF BARGE RAMP DECKING.

INJURED EE IS A BARGE LOADER. AT THE ABOVE DATE AND TIME HE EITHER STEPPED OR JUMP FROM A BARGE UP TO AND ON THE BARGE LOADING DOCK. HE EIGTHER SLIPPED OR LOST HIS BALANCE AND FELL BACK ONTO T HE COVER OF THE BARGE AND THEN ROLLED OFF AND ONTO THE WALK WAY OF THE BARGE.

EMPLOYEE WAS CUTTING METAL ROD. EMPLOYEE GOT IMPATIENT AND TRIED TO FINISH JOB BY BREAKING HALF CUT ROD ON EDGE OF BASKET. CUT PIECE OF ROD BROKE AND FLEW BACK STRIKING EMPLOYEE ON RIGHT SIDE OF FACE.

EMPLOYEE WAS WORKING UNDER FRONT-END LOADER PERFORMING DIALY CHECK. FOREIGN OBJECT GOT INTO EMPLOYEE'S EYE, EVEN THOUGH EMPLOYEE WAS WEARING SAFETY GLASSES.

EMPLOYEE WAS BENDING DOWN TO PICK UP A ROPE ON A TRAILING CABLE WHEN HE FELT SOMETHING IN HIS BACK PULL.

EMPLOYEE WAS SCALING A BENCH IN MINE. SCALING BAR BEING USED BROKE, SO EMPLOYEE USED A LENGTH OF DRILLING STEEL TO COMPLETE SCALING TASK. DRILL STEEL SLIPPED, CAUSING EMPLOYEE TO FALL AND BREA K LEFT ANKLE.

EMPLOYEE DESCENDED FLOOR DRILLING RIG BACKWARDS. EMPLOYEE'S HEAL SLIPPED, CAUSING EMPLOYEE TO SPRAIN SACROILIAC.

EMPLOYEE MADE AN ATTEMPT TO PULL SPEED REDUCER IN ORDER TO GET IT IN POSITION TO PICK UP WITH CHAIN FALL. PULLED MUSCLE IN RIGHT SHOULDER.

EMPLOYEE SMASHED FINGER LOADING NITROGEN BOTTLE INTO BACK OF TRUCK.

EMPL WAS ASSISTING IN MOVING 12 X 12 TIMBERS. EMPL TRIED TO MOVE TIMBER IN PLACE BY HAND INSTEAD OF USING PRY BAR.

FOREIGN MATERIAL ENTERED EE S LEFT EYE WHILE HANDLING OLD CARTONS. EE INITIALLY THOUGHT HE WAS DEVELOPING A STY IN HIS EYE. AFTER WORK EE HAD TO GO TO DR.

EMPLOYEE WALKING IN DARK SECTION OF MINE STEPPED ON CHUNK OF SALT TWISTING LEFT ANKLE

EMPL INSTALLING FLANGE ON NORTH SKIP LEADING CHUTE.FLANGE SLIPPED AND FELL ON EMPL LEFT INDEX FINGER.EMPL FINGER REQUIRED STITCHES.

EMPLOYEE HEARD A NOISE IN POCKETS AT -900 FOOT LEVEL OF MINE. EMPLOYEE HURRIED DOWN STEPS TO CHECK OUT NOISE. ABOUT SIX (6) STEPS FROM BOTTOM EMPLOYEE SLIPPED AND TWISTED LEFT KNEE. DID NOT REQUEST TO SEE DOCTOR UNTIL 5-7-90.

EMPLOYEE ASSISTING IN THE MOVE OF LARGE METAL SAFE. AS SAFE WAS BEING LOADED INTO PICK-UP TRUCK BY HYSTER, SAFE STARTED TO TILT. EMPLOYEE MADE AN ATTEMPT TO STOP SAFE FROM TILTING OVER. SAFE P INNED EMPLOYEES HAND AGAINST REAR WINDOW OF TRUCK.

TWO SHAFT INSPECTORS RUNNING NEW TELEPHONE LINE BETWEEN 900FT & 1000FT LEVEL MINE INJURED INSPECTOR WAS OPERATING SIGNAL CARD WITH HAND OUTSIDE CAGE & WATCHING OTHER INSPECTOR RUN WIRE WHEN SK IP REACHED LANDING AT 1000FT LEVEL INJURED INSPECTORS HAND GOT CAUGHT IN RESTRICTED AREA OF LANDING HOOD & MANCAGE