Carthage Crushed Limestone: 696 MSHA citations Metal/Non-Metal

Miner was stepping down the ladder rungs from approximately a 30" platform when miner's glove hung up on a chain hook. This caused the miner to lose balance and fall to the ground injuring ankle.

Miner was changing engine air filters on Caterpillar 769C haul truck. When EE pulled the filters out of the housing, EE twisted at the waist to set them down on the deck of the truck. The miner felt a shooting pain in lower back.

Miner was dismounting bucket on the powder truck that was lowered to the ground when miner caught boot on the edge of the bucket. Miner lost balance and fell to the ground. Miner sustained injuries to elbow and back. Miner did not immediately request medical attention. At approximately 1:45 that day miner requested to seek medical attention.

Miner was exiting Cannon bolting machine frontwards. Miner slipped on the top step and fell about 4 feet to the ground, landing on feet with legs straight. With legs straight they did not forgive the landing and the employee's back was injured.

Miner was tightening a nut with a hand wrench and had a pain in EE's bicep. EE stepped away from the machine and got lightheaded and fell forward to the ground. EE was with two miners that helped EE up and to the breakroom where EE awaited the manager to take EE to be evaluated by medical personnel.

Miner was walking from mill building to Line #1 loadout. While walking, miner tripped and fell forward over the rail road tracks. Miner was not able to catch self with hands to lessen the impact and miner's face struck the ground. This caused injury to mouth, chin, and left knee. Miner's lip was lacerated and required sutures.

The miner was walking through shop prior to shift, to put lunch in the refrigerator. The shop lights had not been turned on, yet. As EE rounded the work bench, EE tripped over an air brake pod that had been stored under the table for future use. The miner was not able to catch self with hands and fell onto the right arm/side and hit face on the floor.

Miner was pulling 50 lb bags of limestone and started experiencing pain in left shoulder and neck area.

Miner was on top of TAMKO bin shoveling 1 1/4"X 1/2" aggregate that had overflowed onto the bin top. When going into the rock pile with shovel, the miner felt a sharp pain in elbow.

Miner unloading over-loaded trailer, was entering trailer second time when miner realized trailer was moving away from dock, Forklift was 1/2 in 1/2 out, and slid back and fell against dock plate then at angle to ground, when trailer stopped leaving forklift at an angle, with rear counter-weight end on ground, forks in trailer. Miner dismounted equipment.

Miner was operating a CAT D-350 Articulated Haul Truck, hauling C-4 Dust to Stockpile. Upon returning in Snowstorm to Line 2 Load-out, Right Front Drive wheel slipped off roadway into a drain depression, jarring the driver in cab and causing later back pain.

Miner (Maintenance - M5) was with Manager of Fine Grind/Mill Operations and was attempting to cut thru a piece of conveyor belting. Miner had noticed his work utility knife had a dull blade, and upon changing it with new one, was cutting belt when knife skipped/slipped and cut his right lower leg. Miner was transported to OCCU-MED and 4 sutures were used to close small laceration.

Miner is a Mill operator and was operating a C4S Packing machine. Miner was palletizing 50 lb. bags of C4S material when he felt a sharp pain suddenly in his left forearm area. Miner was taken for medical evaluation, and placed on lifting restrictions until a scheduled MRI X-ray can be conducted. Miner is working w/restrictions.

Miner was dismounting side steps coming off powder truck, using three point contact, when upon stepping off w/right foot to anchor dismount off of steps, miner's (r) ankle rolled to side. No fx, sprained right ankle.

Miner operates a WDM Drill, noticed drill bit was dulling, went to Drill Pad area, to change out bit. Miner struck old bit w/2 lb hammer due to being stuck, metal hammer wasn't strong enough and a piece broke off, imbedding itself in upper G.I. area of miner, with downward angle. Piece had to be surgically removed by Specialist/Surgeon. Surgery successful on removal.

As stated by miner, shoulder discomfort has occurred to both shoulders, over a reported period of 10 years. Issue began gradual, but with worsening discomfort, over the last six years. This is the first time miner/powderman has officially sought diagnosis/treatment for reported issues. States after loading production holes for explosive detonation, shoulder hurts at end of day!

M-5 Maint. Mechanic/miner was raising over-head garage doors to open shop. In process, miner felt pain along right "Ribcage" area. Miner thought he'd "Pulled" a muscle. Did not seek immediate treatment. Treated on 10/14/11.

Notification Report Only: Miner suffered a severe heart attack unrelated to job duties, while @ work. Miner was transported from site to Hospital in Joplin, MO. with what has been determined to be coronary blockage. Miner received a "Stint" following ballon surgery, and may require further procedures.

Miner/Loader Operator was dismounting a 1996 CAT 970 to pick up a cone, when his right leg banged against the loader platform, scraping his shin which he grabbed, losing his safety 3-point contact and causing him to fall from ladder steps and injuring his pelvis/hip. Miner suffered fracture to his pelvis.

Miner dismounted a skid-steer loader to retrieve a shovel from near a "Trough" auger, miner ducked under the elevated auger frame going to get the shovel, but forgot to duck going back to his skid-steer, striking his hardhat on the auger bin. Miner suffered a mild stain to his neck. Miner returned to work w/restrictions.

Miner/Mant. shop, was climbing down from elevated position on gradall scaler, when he slipped, losing balance, sliding off fender skirt, approx. 4.5' to floor, bracing w/hands. Position was narrow, without elements of 3-point contact, and too low for fall protection device/rig. Inj. recordable because of wrist brace, miner rtn. to work.

Miner operating frontloader clearing drifts.While turning steering wheel, he felt a spontanous pain (like a pinched nerve) in L. shoulder joint. There was no collision, jostling, or disruption in cab when this feeling occured. Miner waited until next morning, when he said it was still sore, taken to Doctor. Work restriction for 1 week and NSAID meds. given, to be re-eval. 3/18.

Miner was repairing a discharge on a Tanker (semi-truck unit), and was using a "Cheater Bar" (steel pipe) to realign pipe to attach the lock clamp, when the miner felt a pain occurring in the middle section of his stomach region. Injury evaluated medically as a mild/mod. "Umbilical Hernia" w/o obstruction. Miner placed on lifting restrictions. Miner allowed to drive.

Miner works with maint. and was assisting @ Line #2 loadout area, when a slippage occurred on the long belt feed line. Miner was working in cleaning up rock spillage when his left foot rolled on him, spraining his ankle. Injury considered minor to moderate. Miner still working.

Maint. Miner was standing on elevated screen cover, (with handrails present/fall protection), when right foot slipped and miner fell against handrail/mid rail, twisting right leg/knee. Miner did not seek medical treatment @ time. Miner sought treatment for sore knee on 19th, and is working (with brace) awaiting later MRI. Knee diag. as strain-sprain.

Miner was positioning wooden blocks and sliding them (blocks), under the primary shell housing of the crusher. Miner had been working with other personnel, but decided to slide/spot the wooden block himself, straining his left shoulder. Miner did not seek immediate treatment, until mid-day (next date) 10/09/07 @ noon.

Miner was moving long sections of (approx. 21') steel piping from/between trailer and storage area. Miner thought this was how he was injured ? Miner had been instructed to wait for assisstance to arrive, but proceeded to move material on own. Accident/injury not reported until late Monday, Oct. 8th. Rolla Field office called, as well as (800) 746-1553.

Incident occurred 08/17/07 and was reported by miner, 08/20/07. Miner was assisting Mine Supt. in moving some large Mine fans to new positions for draft air, during which a fan was re-started and the miner inhaled small cloud of dust causing some lung irritation. No mask was worn, but was available. Medical, Breathing Treatments and shot. Miner has returned to full work.

Miner (Chief Electrician) was perfoming work on a conveyor (Weigh) belt, adding a load cell unit, when metal piece shifted slightly, causing an approx. 1" length laceration to the miner's index finger. Miner was transported to medical facility, where physician cleaned wound and applied (5) sutures. Miner released to full duty.

Miner stated that approximately 2 wks. prior, he had felt a slight pain in his L shoulder when trying to pull an actuator chain to open a flow valve to load-out. On the 16 th of July, the butterfly valve was again stuck, and required a extra hard tug to open, this time causing a possible sprain to the left shoulder muscles. Driver this time sought medical treatment.

Miner was climbing a external ladder @ the Line #2 load-out section to assist in cleaning out a blocked discharge chute following a rain, when he struck his head on a piece of angle iron support. Miner was wearing his hard hat, but felt a jamming sensation in his neck. Miner did not seek medical evaluation until the next day.

Miner was operating a front loader near the face area of M/NM Limestone mine, when while traveling/loading rock from floor, the equip. blade struck a high spot of solid rock on the floor, stopping suddenly. Miner strained back. Seat belt was in use, Miner did not seek medical care till 06/22/06.

Miner was assigned to maintenance group, and was called upon to assist in checking a railcar (covered hopper-BNSF RR), to see if assistance in closing an unloading grate under the car was possible. Miner injured swinging a hand sledge hammer (8 lbs.) against the grate sliding door jam. Strained lower back/leg. Miner did not seek treatment immediately.

EMPLOYEE NEEDED TO OPEN CLEAN-OUT GATE ON ELEVATOR BELT (BUCKET TYPE). HE WAS ATTEMPTING TO USE (SWING) AN 8 LB. SLEDGE-TYPE HAMMER, AND STRAINED HIS LOWER BACK WHILE DOING SO. EMPLOYEE SAID IT OCCURRED WHILE SWINGING FROM AN AWKWARD POSITION.

Miner is assigned to maintenance, and was changing an alternator out of a gradeall scaling machine, miner had to lay against his own left arm in loosning the attachment bolts with wrench, apparently applied too much pressure to elbow region, and suffered a pinched nerve. Placed on restricted duty for approx. 5 days.

Miner was dis-mounting a ladder rung to step down to the floor @ the mill operations, when he stated his foot (L), slipped and he felt a "Popping" sensation followed by a stabbing pain. Miner was transported to company medical provider where an x-ray revealed a small fx above his left little toe. Miner was wearing safety boots.

Miner was attempting to activate the load-out chute @ the chip's bin, when upon pushing the manual lever forward to start loading, he stated the lever was "tight", and required more leverage to push. Miner stated he felt a slight "Pop" behind/below kneecap, and soreness developed in upper calf, (L), miner was evaluated and diagnoised with a strained calf.

Miner, part of team changing Bull-ring at mill, strained his stomach muscle, R. side. Miner did not report accident immediately, thought pain would subside. Mngt. to reveiw and work to improve JSA. Accident report date 7/18/05, medical restrictions applied. Light duty. Will follow with Sec "D".

While operating roller-mill equipment, EE was talking to coworker. EE stepped back & tripped over a pallet. EE stated he received a twisting type of discomfort to R-shoulder & R-hand. EE did not wish medical eval. at the time, but reported medical eval. request on 6-13-05. Sent to company doctor on 6/13/05 & placed on restricted duty.

Miner stated while approaching an intersection, driving a frontend loader, he traveled across some rough surface, jarring him while his neck was slightly turned, causing some discomfort. Incident was reported to supervisor, but miner didn't seek medical treatment. Pain continued and miner seen by company doctor on 6/22/05. Working now with restrictions.

He was drilling a hole with a electric drill in a chevy truck frame to install a backup alarm. A foriegn object fill behind his safety glasses and went into his right eye.

HE SLIPPED OFF STEP OF TRUCK WHILE GETTING IN. SPRAIN/STRAIN TO BACK.

MAKING STEPS WITH ROCKS AND STATES HE PUSHED A ROCK WITH THE BOTTOM OF HIS FOOT & HIS KNEE GAVE OUT. STRAIN TO LEFT KNEE.

STEPPED OVER A PIECE OF METAL AND STEPPED ON A PIECE OF ANGLE IRON. SPRAINED RIGHT ANKLE. PLACED ON CRUTCHES WITH RESTRICTIONS.

SWINGING A SLEDGE HAMMER, HAMMERING ON A HOPPER CAUSING PAIN IN RIGHT SHOULDER.

GROUND TESTING ON EQUIPMENT. TRIPPED ON CATWALK HITTING HEAD ON EDGE OF TROUGHING ROLLER.

INFLAMMATION AND RASH ON LEFT FOOT CAUSED FROM RUBBER BOOTS.

GRINDING WHEEL BROKE APART.

CLIMBING DOWN STEPS OF LOADER HE MISSED THE BOTTOM STEP AND FELL.

DEVELOPED PAIN IN LEFT WRIST.

STEPPED OUTSIDE OF COMPRESSOR BUILDING-SOMETHINGBLEW INTO RIGHT EYE.

DISMOUNTING FROM TRUCK - SLIPPED ON ICE.

USING A HAMMER TO REMOVE LEGS FROM CONVEYOR. THE CONVEYOR PIVOTED CAUSING HIM TO LOSE BALANCE & FALL APPROX 8-10'. SEPARATION OF LEFT SHOULDER JOINT.

REMOVING A PIECE OF TIN FROM FEED HOPPER, WIND CAUGHT IT & BLEW BACK ON TO THE EE CAUSING LACERATIONS ON BOTH FOREARMS.

WELDING ON CRUSHER-WEARING NEW HELMET.

BRONCHITIS AND ASTHMAS SYMPTOMS CAUSED BY MILL DUST.

HAULING STONE FROM CRUSHER, LOST THE STEERING ON THE R-22, RAN OFF THE ROAD AND ROLLED THE VEHICLE ON ITS SIDE.

MAINT. WAS REBUILDING TORNADO CRUSHED, WHILE REPLACING THE BREAKER RINGS EMPLOYEE SPRAINED HIS WRIST.

TRIPPED OVER BOOT SCRAPER AND TWISTED BACK.

EE WAS CLIMBING A LADDER WHEN A FEED TUBE FEILL & HIT HIM

FILLING HOPPER WITH MATERIAL - FOREIGN BODY BLEWINTO LEFT EYE.

WALKING UNDER WALKWAY HIT HARDHAT ON BOTTOM OF WALKWAY CAUSING DUST & METAL SHAVINGS TO FALL. PARTICAL FELL INTO EE'S EYE

REPORTED ACCIDENT ON 10/30/00. FIRST SEEN DR ON 11/3/00. STEPPING DOWN FROM GRADE ALL, SLIPPED ON THE STEPS AS EMPLOYEE WAS GETTING OUT OF THE CAB. PULLED GROIN.

ATTEMPTING TO GET IN EUCLID HAUL TRUCK AND FELL.

LIFTING A STEEL DRILL, TURNED AROUND AND STRAINED LOWER BACK.

CLEANING OFF A BELT WITH A SHOVEL-DUST BLEW BACK INTO HIS EYE, SCRATCHED CORNEA.

MOVING SPILLED ROCKS OFF OF THE ROAD, PULLED MUSCLE IN GROIN

DISMOUNTING FROM SKID LOADER.

LIFTING. THIS WAS NOT REPORTED UNTIL 2-29-00 AS WORK COMP.

EE BENT DOWN TO GET UNDER TRUCK, HITTING HIS HEAD.

CLIMBING OUT OF LOADER

WORKING ON DUMP TRUCK. PULLING ON 3/4" END WRENCH, WRENCH SLIPPED OFF NUT CAUSING WRENCH TO STRIKE EE ON THE MOUTH.

CLEANING UP A DOORWAY AREA. A THRUST ROLL WAS ON A BROKEN PALLET. EMP ATTEMPTED TO LIFT AND SLIDE ROLL ONTO A USABLE PALLET.

FLIPPING JIB ON THE CRANE, BOOM SWUNG CAUSING HIM TO LOOSE HIS BALANCE AND FALL APPROX 8 FT.

INSTALLING ROOF BOLTS, HEAD OF BOLT TWISTED OFF LETTING THE 5/8 X 5' BOLT FALL DOWN HITTING HIS LEFT LOWER ARM

EE AND ANOTHER EE WAS ON A CATWALK NEAR THE ROOF PULLING A MOTOR UP WITH A ROPE. TEMPERATURE WAS HIGH, BECAME TOO HOT.

WLEDING DISCHARGE CHUTE ON TORNADO SCREEN. (SEVERAL WELDERS WERE WORKING IN SAME LOCATION) WELDER BURN TO EYES.

SHOVELING SPILLAGE FORM STORAGE BINS. WORKING INA BENT OR STOOPED POSITION. SORENESS TO LOWER BACK.

EMPLOYEE WAS CLOSING MANHOLE ON TANKER TRAILER AND IN THE PROCESS OF CLIMBING OFF THE TANK STEPPED ON SOME LOOSE WET GRIT AND SLIPPED.

EMPLOYEE WAS INSTALLING AN AXEL ON 966 LOADER. PUSHING AXEL IN PLACE AND CAUGHT HIS HAND BETWEEN GEAR AND END STOP OF AXEL.

REPLACING GEAR BOXES ON SCREW CONVEYOR. PRY BAR FELL FROM OVERHEAD STRIKING EE ON LEFT FOOT BEHIND STEEL TOE ON BOOT.

RUNNING TO SHUT OFF FEED BELT THAT WAS DUMPING ON THE GROUND GROUND WAS UNLEVEL TWIST ED RIGHT KNEE

HAULING OUT OF MINE. GAS PEDAL STUCK AS HE WAS MAKING A CURVE IN THE MINE. RAN INTO A STONE PILLAR.

MOUNTING TIRE ON GRADE ALL LIFTING TIRE STRAINED LEFT SHOULDER

HAULING ROCK TO CRUSHER - GETTING OUT OF CAB OF EUCLID, CUT MIDDLE FINGER LEFT HAND ON ROUGH PLACE ON DOOR.

EMPLOYEE WAS HELPING TO LOAD CHANNEL IRON.

EE STARTED SHIFT 700 AM, GOT POWDER TRUCK FROM THE SHOP. THE TRUCK HAD BEEN SERVICE L.E. CHANGE OIL, FILTERS, SEPERATED AIR INTAKES FOR POWDER UNTI AND COMPRESSOR, INSCREASED RPM OF POWER UNIT TO AID OIL PRESSURE. EE WENT TO THE MINE GOT HIS LAMP, WENT UNDERGROUND CHECK 3 FACES THAT WERE TO BE SHOT THIS SHIFT. WENT CHECKED PREVIOUS SHOTS AND AREA. LEFT NEW MINE RAMP WENT TO MAGAZIN

PUSHING BOLT THROUGH HOLE ON HAMMER MILL. HOLDING BOLT WITH LEFT HAND, IMPACT HAMMER ACCIDENTLY STARTED CAUSING BOLT TO SPIN. LACERATION TO 1ST FINGER LEFT HAND REQUIRING STITCHES.

EMPL WAS DRIVING PERSONAL VEHICLE FROM WEST MINE WHERE HE HAD TAKEN LOADER FOR NIGHT. HE WAS BLINDED BY SUN. NEXT THING HE KNEW HE HAD HIT EUCLID WHICH HAD ALMOST COME TO COMPLETE STOP. ROIAD WAS 45' WIDE WHERE ACCIDENT OCCURED. EMPL WAS ON WRONG SIDE OF ROAD AT TIME OF ACCIDENT.

I,NAME WAS IN THE POWDER TRUCK BUCKET LOADING HOLES. THE HYDRAULIC HOSE BROKE MAKING IT IMPOSSIBLE TO LOWER THE BUCKET. I,NAME TOOK ANOTHER HOSE TO SLIDE DOWN TO THE GROUND. AS HE WAS LOWERING HIMSELF DOWN HE SLIPPED HITTING THE GROUND WITH A JOLT.

I NAME TOOK HIS3EUCLID TO THE GARAGE FOR REPAIR, HE WENT TO 4 HOLE TO PICK UP ANOTHER EUCLID. HE DUMPED A PARTIAL LOAD THEN CHECKED TO SEE IF BED WAS CLEAN AND DROVE OFF WITHOUT LOWERING DUMP BED. HE DROVE 3NTO OPENING OF CAVE WITH THE BED UP.

NOISE FROM BLAS7.

DAILU RAINSTORM8 IN AREA WATCH POSTED TO OBSERVE FOR LIGHTNING NONE SEEN A SINGLE BOLT OBSERVED XXXX AREA A PREMATURE DETONATION OCCURED 060686 440PM POWDERMAN & HELPER IMMEDIATELY EVACUATE MI NE NO PERSONS I3JURED NO EQUIP DAMAGED INVESTIGATION ON 060786 FOUND 4CARS W TOREN AREA EXPOSED-FACE WIRING DAMAGED-XXXFACE REWIRED & SUBSEQUENTLY DETONATED 1100AM 060786

BRUISE ON TOP OF RIGHT LEG.RUNNING BACKHOE TRIMMING COLLIN ROCK FOLLOWED BOOM DOWN AND HIT HIM ON TOP OF RIGHT LEG.

CLEANING UP AROUND SCREEN WHEN SHOVEL HIT BELT AND HIT HIM IN THE RIBS WITH THE HANDLE

I.NAME PULLING BROKEN STEEL OUT OF HOLE,AFTER STEEL CAME OUT IT FELL ON TOP OF LEFT FOOT.