Georgetown Sand & Gravel Inc. Metal/Non-Metal

Employee stepped out of truck and his right knee gave out.

Looking at arch of welders stinger-flushburn.

REMOVING SCRAP MATERIAL-STEEL GOT CAUGHT ON GLOVE LACEATING LEFT RING FINGER.

JUMPED FROM BEAM TO TRUCK FROM BINS.

EMPLOYEE WAS OPERATING VEHICLE DURING RAINY CONDITIONS. VEHICLE WAS A LOADER. EMPLOYEE WAS COMING OUT OF VEHICLE ONTO LADDER WHEN HE LOST HIS FOOTING AND SLIPPED OFF THE LADDER. HE FELL TO THE GROUND FROM 8' HIGH DROP.

EMPLOYEE WAS REMOVING ON ANGLE FROM PILE WHEN HE ACCIDENTLY KICKED PILE TRYING TO ADJUST WEIGHT TO LIFT AND THE ANGLE UNDERNEATH THE ONE HE LIFTED FELL ONTO EMPLOYEE'S FOOT.

WHILE TIGHTENING A LOOSE BOLT ON A 6 X 16 VIBRATING SCREEN THE 3/4 RATCHET IN WHICH HE WAS USING SLIPPED OFF THE BOLT. THE MINER WAS STANDING IN SUCH A POSITION THAT HE WAS MORE OF LESS PUSHIN G DOWN ON THE RATCHET INSTEAD OF BEING IN A PULLING STANCE. WHEN THE RATCHET SLIPPED OFF THE BOLT IT CAUSED HIM TO MASH HIS THUMB BETWEEN THE RATCHET HANDLE AND SCREEN SPRING SUPPORT.

THIS EMPLOYEE HAD JSUT FINISHED WORKING WITH THE LINES ON A BARGE WHICH WAS IN THE PROCESS OF; BEING LOADED BY OUR #5 DERRICK BOAT UPON COMPLETION HIS WORK WITH THE LINES & JUMPED FROM THE BAR GE TO THE DECK OF THE DERRICK BOAT THE DECK OF THE DERRICK WAS SETTING 2 FEET LOWER THEN THE BARGE UPON LANDING ON THE DECK OF THE DERRICK BOAT THE EMPLOYEE CLAIMS HE FELT PAIN IN HIS RIGHT K

AFTER SPLICING #25 BELT HE WAS REMOVING THE CLOAMPING TOOL AND THE THREADS BROKE OFF A BOLT HOLDING THE CLAMP TOGETHER LETTING CLAMP STRIKE EMPLOYEE ON HIS LEFT HAND AND BRUISED AND FRACTURING TIP OFF LEFT RING FINGER.

EMPLOYEE WAS HELPING TO INSTALL A CHUTELINE PLATE. THE CHUTE WAS BE LOW FLOOR LEVEL AND IT NEEDED LNED UP TO GO INTO PLACE. HE KNELT DOWN AND TRIED TO LINE IT UP BY HAND AND STRAINED LOW BACK. .

EMPLOYEE WAS USING A PRY BAR TO POSITION A ELECTRIC MOTOR IN A SPEED REDUCER

EMPLOYEE HAD MOVED A CRUSHER HAMMER FROM ONE LOCATION IN THE STORAGE YARD TO ANOTHER LOCATION IN THE SAME YARD. WHILE WALKING BACK TO HIS ORIGINAL LOCATION THE EMPLOYEE REPORTED THAT HE FELT PAIN IN HIS LOWER BACK.

54736YEE WAS INSTALLING LINER PLATE IN CHUTE.

EMPLOYEE WAS USING A UTILITY KNIFE TO CUT A PLASTIC SCREEN PANEL KNIFE SLIPPED AND CUT HIS LEFT HAND.

EE WAS CHANGING BEND PULLEY ON CONVEYOR AND HE BUMPED HIS RIGHT KNEE ON AN ANGLE.

EMP ON SIDE LINER ON IMPACT CRUSHER AND HE STEPPED ON EDGE OF SCAFFOLD HE FELL TO CHUTE BELOW 6 FT HITTING R SHOULDER

EMPLOYEE WAS LIFTING STEEL LINER PLATE IN CHUTE.

EMPLOYEE WAS PUSHING WIRE IN CONDUIT HIS HAND SLIPPED AND HIS LEFT HAND WAS CUT.

REMOVING LG STONE FROM FEEDER, LIFTING IT UP GATE FELT PAIN IN LOWER BACK OR HIP

EMPLOYEE WERE FINISHING UP FROM MAKING REPAIRS TO A CONVEYOR TAIL PULLEY. IN THE PROCESS OF REMOVING A COME-ALONG, THE INJURED EMPLOYEE DROPPED IT ON HIS FOOT.

TANK WAS LAYING FLAT ON THE GROUND & EMPLOYEE RAISED IT TO AN UPRIGHT POSITION USING AN UNSAFE LIFTING POSITION BEGAN LOSING TIME 03-07-90& RETURNED 03-14 -90 TO WORK BEGAN LOSING TIME AGAIN O N 12-10-90 FROM THIS SAME ACCIDENT

WHILE LIFTING HAMMERS FOR PENN. CRUSHER EMPLOYEER CLAIMS HE INJURED HIS RIGHT SHOULDER.

EMPLOYER WAS USING A SMALL BAR TO UNWEDGE A STEEL PLATE THAT WAS IN THE DUMP BOX OF A CONVEYOR.THE EMPLOYEE JUST BARELY TOUCHED THE PLATE WITH THE BAR AND THE PLATE SPRUNG UPWARD WITH FORCE ST RIKING THE EMPLOYEE ON THE HAND.

EMPL WAS WALKING ON GRIPSTRICKT. LEFT FOOT SLIPPED OFF EDGE CASUING FOOT TO TWIST & UPPERLEG & BACK.

EMPLOYEE HOISTED THE BEARINGS AND A FEW OTHER ITEMS TO THE TOP LEVEL OF THE PLANT BY WAY OF ELECTRIC HOIST. THE EMPLOYEE REACHED OUT OVER THE HANDRAIL AND LIFTED THE BEARING OUT OF THE LIFTIN G CONTAINER AND STRAINED HIMSELF.

THE EMPLOYEE WAS REMOVING THE OUTER BEARING RACE FROM THE BEARING HOUSING WHILE USING A 12 LB SLEDGE HAMMER AS A SLIDE HAMMER. TWO METAL FRAGMENTS FLEW STRIKING THE EMPLOYEE. ONE FRAGMENT IN T HE LEFT EYE AND ONE ON THE CHIN JUST BELOW BOTTOM LIP ON THE LEFT SIDE.

EMPL WAS HOLDING ELECTRICAL CONDUCT THAT WAS BEING CUT & PARTICLE OF METAL ENTERED LEFT EYE.

EE WAS HELPING TO POSITION NEW FLUMEWAY SECTIONS IN THE OLD FLUMEWAY SO HIS CO WORKER COULD WELD THEM IN. WHEN HIS CO WORKER STRUCK AN ARC TO BEGIN WELDING INJURED EE CALIMS HE GOT A WELDING F LASH IN HIS EYES.

AN OXYGEN TANK WAS LAYING FLAT ON THE GROUND & EMPLOYEE RAISED IT TO AN UPRIGHT POSITION USING AN UNSAFE LIFTING POSITION

EMPLOYEE WAS CUTTING A CONVEYOR BELT WITH A UTILITY KNIFE. KNIFE SLIPPED AND EMPLOYEE WAS POSITIONED SO THAT THE KNIFE CUT HIS LEG JUST ABOVE THE KNEE.

EMPLOYEE WAS INSTALLING A GEAR MOTOR USING A 3/4" ROUND BAR TO LIFT THE MOTOR INTO PLACE FOR BOLTING. THE LIFTING BAR BENT LETTING THE MOTOR SLIP AND FALL. MOTOR LEADS CAUGHT HIS FINGER AND PU LLED IT OUT OF JOINT. EMPLOYEE BEGAN LOSING TIME 1/26/90.

EMPLOYEE HAD JUST FINISHED TAKING A SHOWER AND WAS LEAVING THE SHOWER ROOM AND CUT HIS FOOT ON A FLOOR HEATING AIR VENT WHICH WAS RAISED UP FROM ITS NORMAL POSITION.

EMPLOYEE WAS PUTTING BOLTS IN CLAMP BAR ON 6A SCREEN. HIS MIDDLE FINGER OF HIS LEFT HAND GOT CAUGHT BETWEEN SIDE OF HOLE AND HEAD OF BOLT.

EMPLOYEE WAS USING A 1 1/4" WRENCH TO ADJUST CRUSHER DOOR BLOCKS WHEN HE STRAINED HIS LOWER BACK MUSCLES.

EMPL WAS USING ELCTRIC HOIST TO SETT 55 GAL DRUM ON FLOOR ON NAT PLANT RIGGING CAME LOOSE ON DRUM MAKING EMPL TWIST BODY CAUSING BACK INJURY

EMPLOYEE WAS CARRYING A SPROCKET FROM THE MAINTENANCE BUILDING TO THE NATRUAL PLANT AND STEPPED INTO A HOLE. EMPLOYEE HAD THE SPROKET ON HIS RIGHT SHOULDER AND WHEN HE STEPPED IN THE HOLE IT JAMMED HIS RIGHT KNEE.

EMPLOYEE WAS LIFTING LINDER PLATE TO INSTALL IN CHUTE.

EMPLOYEE WAS INSIDE A GRAVEL SCREEN USING A CUTTING TORCH TO REMOVE BOLTS WHEN HIS SHOULDER TOUCHED ONE OF THE BOLTS HE HAD CUT CAUSING A BURN ON HIS UPPER RIGHT ARM.

EMPLOYEE AND A HELPER WERE REMOVING SCREEN PANELS. EMPLOYEE WAS PULLING WHILE HELPER PUSHED. PANEL CAME LOOSE AND WAS TOO HEAVY TO HANDLE.

WHILE MOUNTING A LADDER TO CAB OF A CLARK FRONT END LOADER OPERATOR PULLED HIS LOWER BACK FIRST STEP ABOVE.

RECURRING BACK PAIN AS RESULT OF INJURY SUSTAINED 062487 RELEASED TO RETURN TO WORK 031788 ON TRIAL BASIS BECAME LOSING TIME AGAIN 041188

FOREMAN WAS LOOKING FOR SOME PARTS THAT HAD FALLEN DOWN UNDER THE PA CRUSHERS FROM THE TEAR DOWN JOB EARLIER IN THE YEAR. WHILE UNDER THE CRUSHERS HE THOUGHT HE WOULD CHECK OTHER WORK TO THE C RUSHERS THAT NEEDED DOING. WHEN CLIMBING UP TO INSPECT THE WORK NEEDED HE DECIDED TO CLIMB ON OUT OF THE CRUSHER. WHEN SWINGING HIS RIGHT LEG UP TO A AREA HE COULD PULL HIMSELF UP AND OUT HE

WHILE RAISING WINDOW IT CAME OUT OF TRACK AND FELL BACK TOWARDS HIM WHEN REACHING UP TO CATCH THE WINDOW HE CLAIMS HE TWISTED HIS BACK

EMPLOYEE WAS INSTALLING NEW WEAR PLATE IN CHUTES ON THE NATURAL PLANT WHILE LIFTING NEW WEAR PLATE IN PLACE HE STRAINED HIMSELF

EMPLOYEE WAS LIFTING AN AIR CYLINDER AT THE NAT. PLANT HOIST. UPON LIFTING, HE NOTICED A SORENESS IN HIS GROIN AREA. HE WAS IN AN IMPROPER LIFTING POSITION.

WHILE RAISING WINDOW IT CAME OUT OF TRACK AND FELL BACK TOWARDS HIM WHEN REACHING UP TO CATCH THE WINDOW HE CLAIMS HE TWISTED HIS BACK

THE EMPLOYEE CL3MBED UP THE SIDEOF A FEEDER FRAME WORK TO SEE WHY THE BLENDING HOPPER GATES WERE NOT WORKING. WHILE DOING THIS HE CLAIMS THAT HE TWISTED HIS BACK.

THE EMPLOYEE WA8 HOLDING A ONE INCH ROD IN PLACE FOR ANOTHER EMPLOYEE TO WELD TOGETHER DURING THE WELDING PROCESS THE EMPLOYEE DOING THE HOLDING RECEIVED A WELDING PLASH.

ON 10-14-86 EMP5OYEE WAS OPERATING A DOZER ON A DIKE WHEN A PORTION OF THE DIKE GAVE WAY ALLOWING DOZER TO SLIDE SIDEWAYS INTO A POND AND THE OPERATOR HURRIEDLY DISMOUNT TO THE GROUND. OPERATO R AT THAT TIME 410-4) MADE NO REPORT OF INJURY EXCEPT A BRUISED SHIN; EMPLOYEE NOW (11/2) STATES THAT HE HAS A HERNIA AND ALLEGES THAT "IT MUST HAVE HAPPENED" WHEN HE JUMPED FROM THE DOZER LA

I NAME WAS PULL3NG A SCREEN INTO PLACE

EMPLOYEE STATES3HE WAS DESCENDING A FLIGHT OF STAIRS & LOST HIS FOOTING ON ICY STEPS & STRUCK HIS KNEE ON THE HANDRAIL

EMP WAS CLIMBING DOWN FROM THE MACHINE TO GO TO LUNCH HE STEPPED ON RIGHT HAND SIDE DRIVE CHAIN AND LOST HIS FOOTING IN DOING SO HE PUT HIS BACK AND HIPS IN A BIND CAUSING THE INJURY

EMPLOYEE STATES THAT WHILE STANDING ON A LADDER LINING UP 2 V-BELT SHEAVES HE LOST HIS BALANCE AND FELL STRIKING HIS LOWER BACK AND LEFT SIDE OF NECK ON A H-BEAM.

EMPLOYEE STATES THAT WHILE MOVING COUNTER WEIGHT FROM VIBRATING SCREEN EMPLOYEE WAS APPLYING PRESSURE TO WRENCH WHICH CAUSED HIS BACK MUSCLE TO SPASM.

EMPLOYEES WERE LIFTING TOP HALF OF PUMP CASING TO PLACE IT BACK ON TOP OF THE BOTTOM HALF. UPON LIFTING AND MAKING A SLIGHT TURNING MOTION EMPLOYEE PULLED THE MUSCLES IN HIS BACK

EMPLOYEE STATES HE WAS TRIMMING OFF A 4" PIECE O FROM A 48"X120"X1/2" STEEL PLATE. UPON FINISHING THE CUT THE 4" PIECE DROPPED OFF STRIKING EMPLOYEE ON LEFT FOOT.

EMP STATES THAT A LARGE STONE WEIGHTING APPROX 100 LBS WAS STUCK ON #28 CONVEYOR WHILE LIFTING THE STONE TO CLEAR THE ELECTRICAL BOXES AND FRAME HE STRAINED SOME MUSCLES

EMPLOYEE STATES THAT HE WAS PULLING A BURNING TORCH UP A RAMPWAY ON THE SECOND LEVEL OF REWASH PLANT AND SLIPPED ON SOME GRAVEL WHICH HAD BUILT-UP ON THE RAMP

EMPLOYEE STATES THAT WHILE WALKING TO WORK AREA FROM SHOP HE SLIPPED ON SOME ICE AND FELL STRIKING HIS BCK