GREENWOOD QUARRY: 131 MSHA citations Metal/Non-Metal

The employee was overhead welding on the water truck and felt a pop in EE's right shoulder. Initially EE did not think anything of it, but later in the shift EE felt another pop in the right shoulder while assisting another employee lift a screen.

Employee was shoveling material from under a conveyor belt and struck a hand on the plants structure. This contact resulted in a bruised fingernail and a slight fracture of the bone on the tip of a finger.

While helping stem shot - Employee was scooping Crushed Rock into bucket for stemming - ee felt sharp pain in side was able to finish work for the day. Told me that it still hurt and I told ee to go to the doctor that evening. Employee is able to come back to work with restrictions. Strain of muscle and tendon of front wall of Thorax.

While loading a shot employee twisted their right ankle.

While putting material in QC pans, EE was picking them up when the material shifted causing the pans to tilt and slide across my fingers cutting three fingers requiring 5 stitches.

Employee exited the service truck to set the wheel chocks. The employee opened the door put his left leg out and then stepped out with the right leg. Employee slipped forward causing the employee to fall and injure his right calf.

Employee working on electrical service, when re-energizing MCC after fix, arc flash occurred.

Driller came forward on October 28, 2013 and reported carpel tunnel and went back to work. He has now come forward again and is scheduled for surgery on 2/5/2015.

Miners were replacing the cable that controls the extension and retraction of the telescoping end of a stacker conveyor. The telescoping end of the stacker moved causing tension on the cable. A miner's foot was caught in the cable resulting in a broken leg. The miner was airlifted to a local hospital. The miner's left foot was amputated just above the ankle.

EE was filling hydraulic tank on D8 dozer and slipped off contacting the ground.

Employee moved a large amount of sample bags during the day. The employee was lifting full buckets of stone all day long onto his scales. The employee was given a prescription for muscle soreness.

Employee was installing a tailpulley, the employee pinched the tip of his finger between the tailpulley shaft and frame resulting in a cut. The cut required stitches.

EE ATTEMPTED TO ASSIST A CUSTOMER UNHOOK HIS TARPING BAR ON HIS TRAILER, AS HE ASSISTED THE TRUCK DRIVER, BAR CAME LOOSE AND STRUCK THE EE IN THE MOUTH. 10 STITCHES

EE WAS MOVING A MICRO FICHE MACHINE FROM ONE OFFICE TO ANOTHER WHEN SHE JAMMED HER THUMB ON A COUNTER TOP.

EMPLOYEE CUT HIS THUMB WHILE PERFORMING MAINTENANCE ON A IMPACTOR.

WHILE CUTTING BEARING FROM TROUGHING IDLER CAN- A PIECE OF METAL PENETRATED LEFT EYE BESIDES CUTTING GOGGLES. EMPLOYEE DID NOT INFORM MANAGE MENT UNTIL 2-8-94-AFTER HE HAD BEEN TO THE DOCT OR ON THAT DAY.

EMPL REPLACING GUARD ON TRIPLE ROLL CRUSHER WHEN HAND SLIPPED CAUSING LACERATION TO LITTLE FINGER RIGHT HAND REQUIRING STITCHES.

EMPL WAS WORKING ON TAILPULLEY BEARING WHILE STANDING IN BIN FULL OF ROCK. HE SLIPPED & CUT FINGER ON HANDLE THAT FLIPS GATE ON SCREEN. CUT REQUIRED.

POWDER TRUCK WAS DRIVING NORTHEAST ON ROAD WHEN HAUL TRUCK STRUCK REAR OF BED HAULTRUCK WAS LEFT OF IMAGINARY CENTER LINE

HE SLIPPED ON DRILL PLATFORM RUNNING HIS LEFT FOOT BETWEEN TRACK RAIL AND FRONT IDLER WHILE DRILL WAS IN MOTION SUFFERING A BROKEN TOE, TORN LIGAMENTS AND CUT REQUIRING 5 STITCHES.

A SPARK FROM WELDER FLEW INTO EYE ALSO SOME METAL.

WELDING ON CRUSHER EQUIPMENT,PART50 AUDIT 02-16-89.

ACCIDENTLY RAIS9D HAND AND CAUGHT IT INTO THE PULLEY OF PUG MILL.

HE WAS CHANGING A TOOTH ON THE BUCKET OF A LOADER AND A SLIVER OF METAL STUCK IN HIS HAND