HATTON QUARRY Metal/Non-Metal

The employee was entering a rail car to clean out material. While stepping down from bottom rung of ladder the employee rolled and injured ankle. Treated as first aid initially, but employee indicated days later that healing was not progressing. Sought medical care on 10/31/16 when learned there is a fractured bone in left foot.

EE was using a pry bar to free up a blockage in the Rip Chute. The employee began to pry the rock upward in an effort to dislodge. At that time some rock began to move, forcing the pry bar down and catching EE hand between the bar and the edge of the opening at the door on the rip chute.(PPE, including impact resistant gloves were in use at time of incident)

Employee was working on an Atlas Copco drill at Martin Marietta Quarry in Hatton, Ar. The catwalk he was standing on has the gator type tread on it. Employee was attempting to remove the hood off engine compartment and when he went to twist his foot, it did not move because boot caught the tread and caused his left Knee to pop and swell.

The night of 2-20-13 a winter storm left snow and ice at the quarry. After the morning meeting on 2-21-13, employee proceeded to walk towards mobile equipment using a set of steps that were ice covered. Holding onto hand rail he fell twisting left knee. Employee worked but knee kept bothering. Work comp approved an MRI on 3-25-13 MRI results shows a tear at dr appt on 4-2-2013.

Commercial truck driver who had been trained & signed off on Hatton Site Specific Awareness training to stay in his truck at all times got out of his truck to release a rock from the tailgate. He lifted the tailgate with his left hand & removed the rock with his right hand. As he did this the tailgate went shut pinching his right hand.

Employee used a box knife to trim a patch to repair a hole in conveyor belting. The employee was pulling the knife toward him and it slipped, causing a 1" laceration on his right thigh.

Employee was using a grease pump to grease the Cat water truck. The pump air locked three times. He shook the pump two times with it in place to release the air lock. The third time he grabbed one side of the pump and the front to lift it off the barrel. When he set the pump down it smashed his thumb.

Employee was cleaning dirt out of an idler roller on the Cat 330 track-hoe using a spade shovel. When he went to make another swipe he caught his right middle finger on some broken fiberglass on the cab caushing a v shape laceration that required nine stitches

Employee was trasported by ambulance for chest pains

Employee was clearing out the jaw crusher after it stalled, and a 2" rock fell and hit him on the chin. He sustained a 1/2" cut on his chin and had to have 2 staples.

Employee was crawling under a Wheel loader to make a repair, he was wearing cotton gloves & a piece of rock, went through the gloves into the base of right thumb, causing pain in fingers.

EMPLOYEE WAS USING A ONE INCH IMPACT TO TIGHTEN LUGNUTS ON HIS HAUL TRUCK, HE FELT PAIN IN HIS LOWER BACK.

Employee was installing a driveshaft in a Off highway truck & was laying in the bellypan, holding the drive shaft in place while he started the bolts. He felt a pop in his back. He didn't report the incident to us for 3 days and we sent to the doctor to be checked out.

EE WAS REMOVING THE BELLY PAN ON A D-155 DOZER. HE HOOKED HIS CHAIN TO THE HINGE ON THE PAN AND PROCEEDED TO REMOVE THE BOLTS WHEN HE ACCIDENTALLY REMOVED THE BOLTS TO THE HINGE, CAUSING THE PAN TO FALL ON HIS ARMS.

EE STATES HE WAS PULLING 30 LB BAGS TO THE BACK OF THE TRAILER WHEN HE FELT PAIN IN HIS ARM.

THE CASE IS STILL UNDER INVESTIGATION AND CONDITIONS CONTRIBUTING TO ACCIDENT HAS NOT BEEN DETERMINED.

EE WAS HAVING PAIN IN BOTHE OF HER WRISTS. WENT TO THE DR. & SHE HAS CARPAL TUNNEL.

EE HAD MOVED HIS TOOL BOX TO HIS WORK TRUCK AND FELT A SMALL STRAIN, HE THEN PICKED UP AN OXYGEN BOTTLE WITHOUT PROPER TECHNIQUE. HE FELT PAIN IN HIS LOWER BACK.

EE WAS MOVING CROSSTIE TO SCATTRACK BUCKET

EE STEPPED OFF THE GRADER, HUNG HIS FOOT UP AND FELL FADE DOWN ON THE CONCRETE FLOOR. HE FELL ON HIS HANDS AND KNEES. HIS LEFT ARM ABSORBED MOST OF THE FALL. HE FRACTURED A BONE IN HIS LEFT FO REARM.

EE WAS CLIMBING INTO THE TRACKHOE WHEN THE DOOR SLAMMED SHUT ON HIS ELBOW.

EMPLOYEE WAS CLIMBING INTO THE LOWER 6X16 SCREENAT THE NORTH PLANT. HE DRAGGED HIS ARM ACROSS A SHARP POINT STICKING UP FROM THE SCREEN DECK. HECUT HIS RIGHT FOREARM AND NEEDED 26 SUTURES.

EE WAS STANDIJNG ON TOP OF THE HANDRAIL ON THE FIRST LEVEL PUTTING THE WATERHOSE ON THE SECOND LEVEL OF THE CRUSHER PLATFORM. HE SLIPPED AND FELL OFF HITTING THE HANDRAIL. HE FELL 7 FEET AND B ROKE 4 RIBS.

LONG TEM EXPOSURE TO AIRBORNE DUST.

LONG TERM EXPOSURE TO AIRBORNE DUST.

LONG TERM EXPOSURE TO AIRBORNE DUST.

LONG TERM EXPOSURE TO AIR BORN DUST.

LONG TERM EXPOSURE TO AIRBORNE DUST.

EE HAS PINS IN ONE OF HIS DISCS IN HIS LOWER BACK. THE PINS ARE WORKING LOOSE DUE TO THE OPERATION OF THE TRACK-HOE. LATE NOTICE DUE TO EE TURNED IT IN ON HIS INSURANCE THEN DECIDED WORKMAN'S COMP.

STRAINED LOWER BACK MOVING A STEEL PIN WEIGHING ABOUT 75 POUNDS FROM ONE PLACE TO ANOTHER. THE PIN HAD OIL ON IT AND EE WAS HOLDING IT WITH BOTH HANDS AWAY FROM HIS BODY CAUSING LOWER BACK STR AIN.

EE WAS WALKING ACROSS THE PUMP PLATFORM, HE STEPPED OVER A PIPE AND TWISTED HIS ANKLE.

BROKE BONE JUST UNDER LEFT KNEE EE WAS WORKING IN THE SOP THE AIR HOSE WAS HOOKED TO LUB TRUCK AND RUNNING FROM SHOP AIR. EE JUMPED INTO LUBE TRUCK TO MOVE IT WHEN HE BECAME ENTANGLED WITH THE AIR HOSE CAUSING HIM TO BE PULLED DOWN AND OUT OF SHOP BY MOVING LUBE TRUCK AND AIR HOSE.

EE WAS ADJUSTING THE CRUSHER USING A HYDRAULIC CYLINDER WHEN THE ROTATION OF THE HEAD CAUGHT HIS RIGHT HAND GLOVE AND PULLED HIS FINGER INTO THE PINCH POINT. IT BROKE HIS FINGER AND PULLED THE MEAT FROM THE BONE.

EE WAS CLIMBING DOWN FROM THE SCREEN AND LOST HIS FOOTING. HE FELL FROM THE SCREEN PLATFORM TO THE GROUND.

EMPLOYEE WAS CLIMBING DOWN OUT OF THE TRAIN CARSWHEN HE SLIPPED AND FELL FROM THE BOTTOM STEP. HE LANDED ON HIS KNEES AND HIT A ROCK WITH HIS LEFT KNEE, CAUSING A CUT.

HE WAS STANDING ON THE TAIL ROLLER OF THE NORTH DELIVERY CONVEYOR BELT-CHANGING BELTS. HE SLIPPED AND FELL THROUGH THE FRAME WORK AND CUT HIS SHIN ON THE TAILROLLER FINS.

EMPLOYEE WAS PUSHING ON THE LID OF THE CRUSHER WHEN SHE SLIPPED AND FELL FEET FIRST TO THE PLATFORM FOUR FEET BELOW. AS SHE FELL, SHE TILTED BACKWARDS AND STRUCK HER HEAD AND LOWER BACK ON THE TOP AND MIDDLE HANDRAILS, RESPECTIVELY.

EE WAS REMOVING GRILL WHEN THE LAST BOLT CAME OUT. THE GRILL SLIPPED AND CAUGHT THE LEFT RING FINGER BEHIND THE NAIL. IT CUT AND BROKE THE TIP OF THE FINGER.

EE CAUGHT HIS FINGER BETWEEN THE DRIVE BELTS AND SHEAVE WHILE MANUALLY TURNING THE TUNNEL CONVEYOR.

EE WAS CUTTING A BAD PIECE OF CONVEYOR BELT OFF THE FEED CONVEYOR AT THE PORTABLE PLANT. HE WAS PULLING THE KNIFE TOWARDS HIM WHEN IT SLIPPED AND CUT HIS KNEE.

EMPLOYEE FELL OFF A LADDER, GRABBED HAND RAIL AND HIT HIS SIDE ON THE EDGE OF THE PLATFORM. PLATFORM IS 6 FEET OFF THE GROUND.

USING A COMEALONG CHAIN THAT SLIPPED & TRAPPED HAND AGAINST HANDRAIL Y

EMPLOYEE WAS WALKING DOWN STEPS OF TIME CLOCK AND TWISTED HIS ANKLE.

EE WAS WORKING FROM AN EIGHT FOOT, ALUMIMUM STEP LADDER. THE EE LOST HIS BALANCE AND JUMPED FROM THE FOURTH STEP. FROM THE BOTTOM OF THE LADDER, TO THE GROUND, WHICH BROKE A BONE IN THE HEEL O F HIS LEFT FOOT.

EE WAS REMOVING A BOULDER HUNG IN THE JAW CRUSHER. A PIECE OF ROCK FLEW OUT OF THE JAW--HITTING THE EE.

EE WAS CLEANING UNDER THE TUNNEL CONVEYOR BELT, LOST FOOTING AND FELL ON CATWALK.

EE WAS OPERATING KOMATSU SHOVEL. WHILE CLIMBING DOWN FROM SHOVEL HE CAUGHT HIS WEDDING RING ON THE HAND RAIL INJURING FINGER.

EMPLOYEE WAS HOLDING A BAR THAT WAS BEING HIT WITH A SLEDGE HAMMER. BAR SLIPPED AND CAUGHT FINGER BETWEEN BAR AND CRUSHER.

EE LIFTED A DRIVE LINE TO INSTALL IN WATER TRUCK NOTICED PAIN IN LOWER ABDOMEN.

EE WAS REPLACING DRIVE BELTS. IN PROCESS EE WAS ROLLING DRIVE BELTS ON PULLEY. MOTIONED TO OTHER EE TO BUMP BELT WITH POWER, TO HELP POSITION BELT TO GO ON PULLEY. DID NOT GET HAND CLEAR. CAUG HT HAND IN PULLEY.

EMPLOYEE WAS DIGGING WITH SHOVEL-CLEANING OUT UNDER CONVEYOR BELT.HE WAS PUSHING WITH RIGHT FOOT ON SHOVEL.FOOT SLIPPED JERKING BACK.

EMPLOYEE WAS WORKING ON A PIECE OF EQUIPMENT AND GOT SOMETHING IN HIS RIGHT EYE.

EE ALLEGED THAT HE ROLLING 40 LB. ROCK OFF RAIL.

EE WAS USING FRONT END LOADER TO BUILD A ROAD. WENT OVER A BUMP IN THE ROAD WHICH THREW HIM TO ONE SIDE HE FELT A POPPING SENSATION IN HIS BACK.

EMPLOYEE WAS PUTTING SCREENS IN THE LOWER DECK OF THE DIESTER AND HE SLIPPED ON THE WALKWAY AND TWISTED HIS RIGHT HIP.

EMPLOYEE WAS DISMOUNTING ENDUMP. THERE WAS GRAVEL ON THE TOP STEP HE SLIPPED & STARTED TO FALL & CAUGHT HIMSELF ON THE HANDRAIL. HE FELT A BURNING SENSATION IN HIS BACK.

EE WAS ON THE FLAT PART OF THE FENDER ON DED DUMP PREPARING TO GET INTO THE END DUMP WHEN HIS FOOT SLIPPED IN SOME ICE AND WENT SIDEWAYS CAUSING A SHARP PAIN TO GO FROM HIS BACK INTO HIP & LEG

EMPLOYEE WAS WALKING TO THE SAND STACKER TO SHOVEL MATERIAL OUT FROM UNDER IT AS HE STEPPED OFF OF A BACK BY THE STACKER THE BANK CAVED IN & HE FELL TWISTING HIS LEFT KNEE

EE WAS ON THE WALKWAY FOR THE SCREEN WHEN HIS FOOT SLIPPED AND HE FELL AND GRABBED A HOLD OF THE SCREEN WHICH SWUNG HIM INTO A PIECE OF METAL.

EMPLOYEE LIFTED A WATER PUMP & TRIED TO MOVE AN I-BEAM THAT WENT TO READ SCREEN SO THEY COULD WELD ON IT.

EMPLOYEE WAS UNLOADING A TRAILER, HE JUMPED OFF BACKWARDS WITH LUMBER IN HIS HANDS AND HIS BACK POPPED.

A TRUCK WAS DUMPING AT THE PIONEER FEEDER AND A ROCK ROLLED OFF THE SIDE OF THE TRUCK AND HIT THE RAM DISLODGING SEVERAL ROCKS THE ROCKS BOUNCED OVER THE WALL AND TWO OF THEM STRUCK EE IN THE BACK WHILE HE WAS WALKING AWAY FROM THE FEEDER.

EMPLOYEE SHOVELING AT THE BALLAST STACKER, HE BENT DOWN TO PIECK SOMETHING UP AND GOT HIS ARM CAUGHT BETWEEN THE RETURN ROLELR AND THE CONVEYOR BELT.

EMPLOYEE WAS HELPING TO CHANGE A T AIL R OLLER ON THE CONVEYOR FOR THE JAW DISCHARGE WHILE HE WAS HELPING LIFT THE ROLLER FROM T HE FRAME THE ROLLER SLIPPED & PINNED HIS RT HAND BETWEEN THE FR AME & SHAFT

EMPLOYEE CHANGING LINER INSIDE THE CHUTE ON SHAKER, LOST HIS FOOTING AND SLID INTO CHUTE WITH RIGHT LOWER LEG BENT BACK WITH HEEL TOUCHING BUTTOCKS.

EMPLOYEE WAS TRYING TO DRY HIS CLOTHES OUT BY STANDING BY A FIRE (IN A BARREL) WHICH WAS BUILT FOR WARMING. HIS COAT AND T-SHIRT CAUGHT ON FIRE. COAT WAS MADE OF A NYLON FABRIC WHICH STUCK TO HIS HAND WHEN HE FELT TO SEE IF HIS COAT WAS BURNING.

EMPLOYEE PICKED UP 8D BATTERY (100 LBS) & FELT SOMETHING PULL IN HIS BACK

EMPLOYEE LIFTING AND HOLDING SCREEN SHAKER WHILE CO-WORKER REMOVED WASHER FROM UNDER LEGS TO BE LEVELED.

55039GHTENING BOLT ON SCREEN AND THE BOLT BROKE AND SMASHED HIS FINGER BETWEEN SCREEN.

EMPLOYEE ALLEGES THAT WHILE WELDING A PIECE OF HOT SLAG FROM WELD FELL INTO BACK OF PANTS AT THE WAIST LEVEL BURNING EMPLOYEE.

LOST BALANCE THROWING SCREEN OFF SHAKER FELL DOWN STEPS SPRAINED L ANKLE

NO ACCIDEN OCCURRED-EMPLOYEE COMPLAINS OF SORENESS IN WRIST.

EMPLOYEE WAS OPERATING LOADER WHEN HE COMPLAINED OF SHORTNESS OF BREATH, CHEST PAIN AND NUMBNESS IN LEFT ARM.

ENDUMP DIED AND EMPLOYEE LOST CONTROL AND ROLLED DOWN THE HILL INTO RIP PILE. HE WAS GRIPPING THE STEERING WHEEL TIGHT TO HOLD ON AND INJURED LEFT HAND.

EMPLOYEE WAS ASSISTING IN USING A PRESS 150 TONE TO BREAK DOWN THE TRACKS ON THE PC400 TRACKHOE WHILE TRYING TO PUSH THE PINS OUT OF THE TRACKS USING THE PRESS THE PINS ON THE PRESS JUMPED OUT & HIT THE GROUND & BOUNCE UP & HIT EMPLOYEE IN THE ANKLE

EMPLOYEE WAS WELDING ON JAW JOPPER AND RAISED HIS HOOD TO PLACE A ROD ON STINGER.A PERSON WELDING NEXT TO HIM WAS CHIPPING AND A PIECE OF HOT SLAG HIT RIGHT EYE.

EMPLOYEE WAS INSTALLING ROLLERS ON THE CONVEYOR.HE WAS SITTING ON A CROSS BRACE OF THE CONVEYOR,WITH HIS LEFT LEG BETWEEN THE BRACE HE WAS SITTING ON AND ANOTHER BRACE THAT RUNES DIAGONAL ACRO SS THE CONVEYOR.WHEN EMPLOYEE ATTEMPTED TO RAISEBELT ON ROLLER HIS FOOT SLIPPED CAUSING EMPLOYEE TO FALL HOOKING HIS LEFT LEG BETWEEN CROSS BRACES.POSSIBLE TORN CARTILAGE IN LEFT KNEE.

EMPLOYEE INSTALLING WATER PUMP AND RADIATOR IN THE GAS WELDER.HE WAS PUSHING AND PULLING ON RADIATOR TO GET IT IN PLACE AND STRAINED ABDOMINAL MUSCLES.

EMPLOYEE SLIPPED DOWN FROM LADDER TO THE GROUND(THE GROUND WAS WET) AND SLIPPED.LEFT KNEE SPRAIN.

EMPL REPAIRING CONVEYOR BELT USING TIMBER UNDERNEATH BELT.TIMBER WAS SUPPORTED BY 2 PIECES OF METAL.PIECE OF METAL SLIPPED FROM UNDER TIMBER STRIKING EMPL ON TOP OF FOOT.

EMPLOYEE WAS BENT OVER SHOVELING. WHEN HE STOOD UP STRAIGHT, HE HAD A SHARP PAIN IN HIS LEFT HIP AND LOWER BACK.

TIGHTENING BOLTS IN WASHER, EMP FELL STRADLE ON LOG STAND

TIGHTENING TRACK PAD BOLTS ON DOZER SOCKET SLIPPED OFF BOLT CAUSING EMP TO SLIP AND FELL GROUND

EE WAS SHOVELING AT THE FINISH CRUSHER. HE GOT TO HOT BUT KEPT SHOVELING UNTIL HE PASSED OUT.

EMPLOYEE STEPPING ONTO CONVEYOR BELT WITH RIGHT FOOT, RIGHT FOOT SLIPPED DUE TO FROST. LET KNEE HIT SIDE OF CONVEYOR BELT.

EMPL WAS WELDING METAL ON KOMATSU BUCKET WHEN PREVIOUSLY WELDED METAL STRIP BROKE LOOSE FROM WELD STRIKING EMPL IN SHOULDER & HEAD.

EMPL OPERATING ENDDUMP,SEVERAL ROCKS FELL FROM BUCKET OF LOADER.ONE ROCK FELL AND HIT LOWER RIGHT CORNER OF WINDOW ON TRUCK DOOR.IT BOUNCED FROM THERE AND HIT EMPL ON BACK OF LEFT ARM.

EE WALKING DOWN SLOPE AND TOES GOT STUCK IN A CRACK IN THE GROUND, HEEL SLIPPED AND TWISTED HIS RIGHT KNEE.

WORKING ON CRUSHER SLIPPED ON WET BELT FELL IN CHUTE

EMPL CLIMBING INTO LOADER,HAND SLIPPED OFF HANDRAIL AND HE FELL TO GROUND AND LANDED ON LEFT ARM.HURT LEFT ARM & HIP.

EE CARRYING PIECE OF HEAVY TUBING FROM THE TRUCK TO THE SCREEN. SLIPPED ON LOOSE GRAVEL AND PULLED MUSCLES IN LOWER BACK.

EMPLOYEE ALLEGES HE WAS BENT OVER PICKUP TOOLS WHEN ANOTHER EMPLOYEE THREW RUBBER STRIPS WEIGHING APPROX 3 LBS FROM THE 5X16 SCREEN FROM HEIGHT OF ABOUT 8 FEET.EMPLOYEE ALLEGES STRIP HIT HIM O N UPPER NECK HEAD AND SHOULDERS.

WHILE MOVING 8 INCH PIPE EMPLOYEES FOOT SLIPPED ON A ROCK WHEN HE LIFTED THE PIPE UP. PULLED MUSCLE IN RIGHT HIP AND RIGHT LEG.

EMPLOYEE SHOVELING DIRT. PULLED SHOVEL BACK AND TWISTED RIGHT WRIST.

EMPLOYEE CHANGING SCREEN ON 5 X 16 SHAKER, SLIPPED ON PILE OF DIRT AT END OF SHAKER. FELL 10-12 FEET.

EMPLOYEE BUMPED HIS LEFT KNEE ON A PIECE OF ANGLE IRON ON TOP OF THE CONVEYOR.

EMPLOYEE WAS DR3VING ENDUMP DOWN HAUL ROAD AND AXEL BROKE. EMPLOYEE JUMPED BEFORE WENT OFF THE RUNAWAY RAMP.