Martin Marietta - Fieldale Quarry Metal/Non-Metal

miner was doing his pre-shift on a Kobelco SK210 long reach excavator when he closed the engine compartment then slipped and fell. He injured his left knee on the metal track while falling off the back of excavator around 6.5 feet below. went to the hospital where they said it was a sprained knee. Did not return to work on 3/24/2014 making it reportable.

Miner was running a 1 inch impact wrench to take bolts out of a cutting edge on the front bucket of a 990H. One bolt got lodged in the socket and he tried taking it out with his hand while slowly turning the socket to jar it loose. A sharp edge then cut into the glove cutting his hand right below his thumb on his left hand.

Employee had just clocked out for the day and was walking down the wooden steps when one of the boards broke and sent him falling backwards and injuring his back. He went home that night to rest and came into work the next morning with his back still hurting. He went half way through his shift then went to the doctor.

**Medical Stroke** The miner became dizzy and weak in the morning of his shift. It was decided by the mine superintendent to transport the miner to the local hospital. The miner was transported via the superintendent. While in the ER the miner suffered a stroke. THIS IS UNDER PROTEST AS A MEDICAL INJURY NOT RELATED TO MINING ACTIVITIES.

While grinding a piece of old metal out of a 4-1/4 crusher with a hand held grinder, a small piece of metal shaving became lodged in the right eye. Safety glasses were being worn. The ER ground the metal down the day after the injury. The doctor buffed the eye and stated that the eye would be fine. There were no lost work days because of this injury.

LIFTING DRILL HAMMER & HURT HIS BACK. ACUTE SPRAIN IN BOTTOM RIGHT SIDE OF BACK.

EE WALKED INTO A PIECE OF ANGLE IRON AND BRUISED HIS RIBS.

EMPLOYEE WAS REMOVING A CUTTING EDGE FROM A LOADER BUCKET, WHEN IT CAME OFF IT BOUNCED AND HIT ON HIS RIGHT FOOT.

EMPLOYEE WAS PUTTING SHIMS IN JAW CRUSHER WHEN HE FELT PAIN IN HIS BACK.

EMPLOYEE WAS PRYING ON THE TOP OF A BARREL OF ANTIFREEZE WITH A PRY BAR, WHEN HIS LEFT HAND SLIPPED AND HIT A SHARP EDGE ON A PIECE OF METAL CUTTING THE TOP OF HIS HAND.

EE WAS PRYING ON A SCREEN WITH A 12" SCREWDRIVERWHEN IT SLIPPED AND HIT HIM IN THE NOSE. HE WAS WEARING HIS SAFETY GLASSES.

EE BENT OVER TO RAISE LID ON MAIN WATER VALVE AT JAW, WHEN SHE FELT A SHARP PAIN IN HER BACK.

EE WAS LIFTING THE HOOD COMPARTMENT OVER THE ENGINE OF THE ROCKBREAKER WHEN HE FELT A TWINGE IN HIS BACK. HE REPORTED IT THEN BUT DID NOT GO TO THE DOCTOR UNTIL 12/26/00.

EE PARKED HIS 988 CAT LOADER AT JAW AREA AT 1130 ON 5-5-99 TO TAKE HIS LUNCH BREAK. WHEN HIS LEFT FOOT HIT THE GROUND WHILE CLIMBING DOWN LADDER, HIS LEFT ANKLE TWISTED. THE GROUND WAS PERFECT LY FLAT AND THERE WERE NO LOOSE ROCKS AROUND. HE MAINTAINED 3 POINTS OF CONTACT AT ALL TIMES.

EE ORIGINALLY FELT PAIN IN HIS SHOULDER ON 12-3-98 WHILE CHGANGING WEAR PLATES IN JAW. HE DID NOT GO TO DR. AND PAIN WENT AWAY AFTER A FEW DAYS. HE RE-AGGRAVATED HIS RIGHT SHOULDER ON 4-30-99 AT APPROX 1900 WHILE TAKING BOLTS OUT OF SIDE RAILS IN ORDER TO CHANGE SKIRT BOARD RUBBER UNDER 5 1/2' CRUSHER. HE FELT TYHE PAIN AGAIN IN HIS RIGHT SHOULDER AND WENT TO DR. ON 5-2-99.

MAN WAS GETTING SCRAP (WASTE) MATERIAL LOADED ON HIS TRUCK. AFTER BEING LOADED HE CLIMBED UP STEPS TO CRANK THE TARP OVER HIS BED. AFTER CRANKING TARP, HE PROCEEDED TO CLIMB DOWN STEPS, WHEN H E SLIPPED. HE REACHED AND GRABBED THE CRANK TO PREVENT HIMSELF FROM FALLING. HIS WEDDING RING GOT CAUGHT ON THE CRANK PULLING HIS LEFT RING FINGER OFF AT THE KNUCKLE. HE WAS IMMEDIATELY TAKEN

HELPING VENDOR STACK BOLT BINS BUT WAS "HORSEPLAYING" WITH ANOTHER EMPLOYEE. THE OTHER EMPLOYEE SWATTED AT INJURED. HE STEPPED BACK TO AVOID CONTACT. HIS RIGHT FOOT SLID ON SOME SAWDUST. HIS K NEE TWISTED AND HE FELL PUTTING ALL HIS WEIGHT ON HIS RIGHT KNEE.

EE WAS STANDING BESIDE CONVEYOR ON FLAT GROUND. ANOTHER, EE WAS ON THE OTHER SIDE. THEY WERE PRYING IDLER INTO PLACE. PRY BAR SLIPPED AND CAUGHT EE FINGER WHEN IDLER FELL.

SETTING CRUSHER. MASHED HAND BETWEEN CRUSHER AND PIECE OF SUPPORT.

EE WAS LEAVING CRUSHER CONTROL HOUSE APPROX 10AM. WHILE WALKING DOWN STEPS, EE ALLEDGELY SLIPPED ON 2ND OR 3RD STEP & SLID DOWN TO PLATFORM. EE HELD BOTH HANDS ON HANDRAIL AS HE SLID. IT WAS R AINING AT THE TIME. DID NOT INFORM FOREMAN UNTIL2 OR 3 WEEKS LATER. IN MARCH OF 1997 INFORMED THAT HE WAS HAVING BACK PROBLEMS DUE TO THE ABOVE.

OPERATING JAW CRUSHER. CRUSHER KICKED OUT. WAS ATTEMPTING TO ADJUST A CHAIN ON ROCK TO HOIST UP SO ROCK WOULDN'T FALL THAT WAS HUNG. ANOTHER ROCK FELL THROUGH HOLE FROM TOP, STRIKING EE ON RT HAND.

EES WERE KNOCKING TOGGLE INSERTS OUT OF TOGGLE. INJURED EE WAS HOLDING BAR THAT WAS BEING STRUCK BY 2ND EE. 2ND EE MISSED THE BAR AND STRUCK INJURED EE ON THE ARM.

USING WEEDEATER TO CLEAR WEEDS AROUND THE PLANT.

THE EMPLOYEE WAS HELPING PUT NEW VBELTS ON DRIVE THEY WERE ROLLING BELTS ON WITH SHEAVE BY TURNING IT WHEN SHEAVE TURNED OVER IT TWISTED EMPLOYEES LEFT WRIST & WRIST THEN CAME IN CONTACT WITH THE SHEAVE GUARD

WAS IN THE PIT AREA OF THE QUANG HOOKING UP A WATERLINE. WAS HOLDING A 6" HOSE BETWEEN HIS RIGHT SIDE AND RIGHT ARM PRESSING AGAINST HIS RIB TO HOLD THE HOSE.

EMPLOYEE WAS STANDING ON 5 1/2" CRUSHER PLATFORM UNSTOPPING CRUSHER WITH 5' PRY BAR. HE INSERTEDPRY BAR BETWEEN FEEDCONE & FEED HOPPER & WAS GOUGING BAR WITH RIGHT HAND WHILE RESTING LEFT HAND ON ANGLE IRON THAT HOLD FEED HOPPER. A 10" ROCKDISLODGED FROM SCALPING SCREEN & HOPPED OFF THRUST SIDE OF SCREEN & ROLLED DOWN CATWALK STRIKING EMPLOYEE'S LEFT HAND.

EE HAD CUT BEARING AND WAS USING SLEDGE HAMMER TO BREAK HOUSING LOOSE. A PIECE OF SLAG DISLEDGED FROM BEARING HOUSING AND STRUCK EE IN THE EYE. EE WAS USING SAFETY CUTTING GLASSES.

DOING MAINTENANCE TO PRIMARY CRUSHER EMPLOYEE WS CRAWLING OUT FROM BENEATH PITMAN ON PRIMARY CRUSHER WHEN HE STOOD U P MISJUDGED DISTANCE FROM BEAM & STRUCK MIDDLE OF HIS BACK AGAINST IBEAM

OPERATING DRILTECH DRILL CHANGING DRILL STEEL. ON CATWALK REMOVING EXTRA DRILL STEEL. STEEL WAS HOISTED BY CABLE. WAS POSITIONING STEEL IN SLOT TO ALLOW FOR LETTING MAST DOWN. WHEN HE LET DOWN ON WINCH CONTROL TO SET STEEL. THE STEEL KICKEDBACK, PINCHING HIS THUMB BETWEEN LOOSE STEEL AND STEEL ATTACHED TO ROTARY HEAD.

HE AND ANOTHER EMPLOYEE WERE CHANGING SCREENS. WAS LIFTING BACKPLATE TO PUT IN PLACE & IN DOING THIS, HE TWISTED HIS WRIST.

THIS EE WAS HELPING REPAIR JAW CRUSHER AT TPRIMARY PLANT, TRYING TO HOOK A CHAIN TO PULL CRUSHER BAKC IN PLACE. WHEN HANGING CHAIN ACROSS A RUST BEAM, FOREIGN OBJECT FELL INTO HIS LEFT EYE.

INJURED EMPLOYEE IS SWITCH HOUSE OPERATOR, MONITORING THE CRUSHING OF STONE AS IT COMES OFF BELTS, ETC. IT WAS A RAINY DAY AND HE NOTICED #8 STONE WAS GETTING DIRTY AND HE WENT OUTSIDE SWITCH HOUSE TO CHECK ON THEM. ON THE WAY TO THE CRUSHER PLATFORM, HE TRIPPED OVER A CABLE. AS HE FELL, HE HIT HIS HAND ONA PIECE OF METAL ON THE GROUND.

EMPLOYEE WAS LOADING PUGMILL ONTO TRUCKS AT PUGMILL HOUSE. THERE WAS A WATER VALVE STICKING OUT AT THIS LOCATION AND WHEN HE RAISED HIS HEAD, HE STRUCK THIS WATER VALVE WITH HIS HEAD, CAUSING A LACERATION TO LEFT SIDE OF HEAD.

EMPLOYEE WAS OPERATING THE CRANE. HE GOT OUT OF THE CRANE TO LIFT A ROCK OUT OF THE WAY SO THAT THE CRANE COULD BE MOVED. WHEN LIFTING THE ROCK, HE FELT PAIN IN HIS LOWER BACK.

TWO EMPLS WERE TAKING GAS TANK LOOSE FROM CONCRETE PAD. WHEN THEY THOUGHT THEY HAD IT LOOSE, WITH ONE EMPL ON EACH SIDE, THEY STARTED TO LIFTBUT ELECTRIC LINE WAS STILL ATTACHED CAUSING A PULL BACK MOTION.

THE EE AND PLANT LEADMAN WERE PUTTING PARTS BACK TOGETHER ON CRUSHER HEAD WHEN TURNING THE FEED DISTRIBUTOR OVER IT SLID ON THE PLATFORM MASHING EE S FINGER.

HOT SUMMER WEATHER WHEN BEES BUILD NEST IN GROUND. SEVERAL STINGS TO ARMS AND LEGS.

A CYLINDRICAL PISTON (OFF DRILL HAMMER) WAS POSITIONED ON SHOP WORKBENCH WITH NO MEANS TO PREVENT IT FROM ROLLING. EE WAS STANDING BESIDE WORKBENCH WHEN BENCH WAS JARRED CAUSING THE PISTON TO ROLL OFF AND STRUCK HIS LEFT FOOT, BRUISING HIS FOOT.

EMPLOYEE WAS USING A TORCH TO CUT BOLTS WHICH SECURE TOGGLE ENDS IN A TOGGLE A HOT BOLT HEAD LANDED ON CONCRETE PAD HOT BOLT HEATED UP THE CONCRETE CONCTRETE CRACKED & CAUSED THIS HOT BOLT HE AD TO FLY THRU THE AIR & WENT DOWN THIS EMPLOYEESHIRT COLLAR

EMPLOYEE WAS TIGHTENING DOWN ON THE 3' CRUSHER AT MAIN PLANT USING A BIG WRENCH TO KNOCK PIN OUT. FINGER WAS CAUGHT BETWEEN WRENCH AND METAL PLATE ON CRUSHER, BREAKING HIS LEFT INDEX FINGER.

EMPL WAS ASSISTING ANOTHER EMPL TO REMOVE SHAFTEON CRANE. WAS HAMMERING ON SPROCKET THAT WAS ATTACHED TO SHAFT TO DRIVE IT OUT. SLEDGE HAMMER STRUCK SIDE OF CRANE CASUING EMPL TO LOSE BALANCE & CUT FINGER ON SPROCKET TOOTH. LACERATION TO LEFT INDEX FINGER REQUIRED FOUR SUTURES & RESTRICTED USE OF HAND FOR 3 WEEKS.

WAS LOADING THE STOCK & STONE TRUCK AT THE FINISHING PLANT BINS. WHEN HE REACHED DOWN TO PULL THE GATE OPEN, HE PULLED A MUSCLE IN HIS BACK.

WAS CLEANING UP WITH A SHOVEL BEHIND AND BESIDE BELT CONVEYOR UNDER FEEDER AT JAW CRUSHER.ROCK FELL OFF CONVEYOR STRIKING HIS HARD HAT CAUSING HIM TO DROP TO HIS KNEES.IN DOING SO AS HE WENT D OWN,TWISTED HIS BACK WHICH AGGRAVATED A PREVIOUSBACK INJURY FROM AN AUTO ACCIDENT.

EMPLOYEE WAS DOING MOBILE EQUIPMENT REPAIR IN THE SHOP. HE WAS USING A DRILLPRESS TO DRILL A HOLE IN A PIN. THE PIN SLIPPED OUT FROM THE PLIERS IN WHICH IT WAS BEING HELD, AND SLAMMED INTO H IS LEFT HAND. RESTRICTED ACTIVITY OF LEFT HAND FOR 5 DAYS. LACERATION TO LEFT PINKY FINGER ON LEFT HAND RQUIRING FIVE (5) SUTURES.

EMPL HELD THE BASE BOLT OF THE IDLER WITH AN END WRENCH WHILE HELPER ATTEMPTED TO LOOSEN THE BOLT WITH A RATCHET EMPLS WRENCH SLIPPED SMASHING HIS FINGER AGAINST THE CONVEYOR STRUCTURE

HELPING REMOVE TIMING GEAR FROM DRIVE SHAFT OF DEISTER FEEDER. WHEN GEAR PULLED NEAR END OF ECCENTRIC DRIVE SHAFT SHAFT SPUN IN GEAR. SHIFTING OF SHAFT PULLED EMPL HAND BETWEN TEETH OF DRIVE & DRIVEN GEARS.

EMPLOYEE WAS WORKING IN MAINTENANCE SHOP REPIARING BUCKET ON 988B LOADER.HE LOST HIS GRIP WHILE AHNDLING A BOFERS ADAPTER.THE ADAPTER CAUGHT HISD FINGER AGAINST THE CONCRETE FLOOR,MASHING HIS FINGER WHICH BROKE THE END OF THE INDEX FINGER ON HIS LEFT AHND.

EMPLOYEE WAS PERFORMING REPAIRS TO THE TRANSMISSION FROM THE UNDERSIDE OF A 91 FD EUCLID TRUCK.AS HE ATTEMPTED TO COME OUT FROM UNDER THE TRUCK,HIS HARD HAT FELL OFF AND HE STRUCK HIS HEAD ON THE BOTTOM OF THE OPEN RIGHT HAND DOOR OF THE TRUCK.

EMPLOYEE WAS OPERATING 988B LOADER IN PIT WHICH HAD A RIGHT WINDOW GLASS SHATTERED PREVIOUSLY AND WAS SCHEDULED FOR REPLACEMENT THIS DAY. THE BUCKET TOOTH CAUGHT UNDER A LARGE ROCK, BUCKET SLI PPED LOOSE, JARRING LOADER, SENDING FRACTURES OF GLASS ACROSS EMPLOYEE FROM THE SHATTERED WINDOW.

MOVING 38B CRANE AWAY FROM WEST WALL FACE WHEN SWINGING BOOM (APPROX 50 DEGREE BOOM ANGLE) HE ALLOWED DROPBALL TO CROSS OVER HIGHWALL OF LOWER BENCH BOOM AT THIS POINT WAS PERPENDICULAR TO TR ACKS AND REAR OF CRANE HAD RAISED HE RELEASED DROPBALL AND JUMPED FROM CRANE BEFORE CABLE SNAPPED AND CRANE RETURNED TO GROUND HE INJURED HIS BACK WHEN HE JUMPED

EMPLOYEE WAS WALKING ACROSS THE QUARRY FLOOR WHEN HE STEPPED ON A ROCK TWISTING HIS RIGHT ANKLE.

EMPLOYEE WAS OPERATING 38B CRANE IN THE QUARRY PIT. HE WAS WALKING ON THE RIGHT HAND CATWALK OF THE CRANE WHEN HIS LEFT FOOT CAUGHT IN A HOLE IN THE WALKWAY, CAUSING HIM TO TWIST HIS LEFT KNEE

EMPLOYEE WAS STEPPING UP INTO LOADER. HIS FOOT SLIPPED OFF THE 3RD STEP CAUSING HIM TO FALL ON THE GROUND. WHEN HE FELL, HE LANDING ON SOME ROCK ON THE GROUND, STRIKING IT WITH HIS LEFT SIDE A ND BACK.

EMPLOYEE WAS WELDING ON LOADER BUCKET IN SHOP. BUCKET NEEDED MOVING SO HE CLIMBED INTO LOADER TO RAISE BUCKET. WHEN STEPPING BACK OUT OF LOADER, HIS SHOESTRING HUNG IN LOADER STEP CAUSING HIM TO FALL. WHEN HE FELL, HIS FIGNER WAS CUT ON LOADER CAB WHICH WAS LYING ON THE FLOOR OF THE SHOP.

EMP WAS CUTTING3SPIRAL BLAST HOLE TUBING WITH A KNIFE. KNIFE SLIPPED STABBING HIM IN LEFT LEG JUST ABOVE ANKLE. SUTURES REQUIRED

I,NAME WAS HELP3NG LOAD EXPLOSIVES INTO BOREHOLES ON SHOT. I,NAME WAS HOLDING A FLEXIBLE PLASTIC PIPE CONNECTED TO AN AIR COMPRESSOR DOWN A BOREHOLE USING THE PNEUMATIC FORCE TO REMOVE UNDERST RENGTHED FERTIL3ZER FROM THE HOLE. SOME OF THE FERTILIZER BLEW INTO HIS EYES CAUSING A PAINFUL IRRITATION THAT REQUIRED THE ATTENTION OF A PHYSICIAN.

EMPLOYEE WAS DR3LLING OVERSIZED ROCK WITH AIR TRACK DRILL IN QUARRY JUST BELOW HIGH WALL. A LOOSE ROCK FELL FROM HIGHT WALL STRIKING THE BOULDER THAT EMPLOYEE WAS DRILLING. ROCK ANGLED OFF BOU LDER STRIKING E4PLOYEE'S LEFT FOOT.

EMPLOYEE WAS CL9ANING UP IN SHOP, HANGING V-BELTS ON WALL. HE WAS USING A 3 FT STEP LADDER. WHEN HE STEPPED OFF LADDER, HE STRUCK THE LOWER PART OF HIS BACK ON AN OIL DRUM THAT WAS SITTING THE RE. 3

EMPLOYEE WAS OB8ERVING OPERATION OF 38B CRANE FROM CATWALK TO SEE IF CONTROL LEVERS WERE BEING USED PROPERLY. CRANE WAS FRACTURING OVERSIZED ROCK. EMPLOYEE WAS STRUCK BY ROCK FRAGMENT RESULTIN G FROM IMPACT O0 DROPCROSS ON ROCK.

EMPLOYEE WAS ST2CKING REPLACEMENT PARTS (HYDRAUCLIC PUMP) ON METAL SHELF IN SHOP ADDITION. THE COMPLETE SHELF UNIT ASSEMBLY FELL FORWARD. HE GRABBED THE UNDERNEATH SIDE OF ONE OF THE ADJUSTABV BLE SHELVES ATT9MPTING TO PREVENT THE UNIT FROM FALLING ONTO ELECTRICAL BREAKER PANEL ON SHOP WALL. AS HE DID THIS, FOUR OF HIS FINGERS ON HIS RIGHT HAND WERE CUT.

EMPLOYEE WAS IN3THE SHOP DOING REPAIR WORK ON 980 LOADER. HE WAS REMOVING HEAVY PARTS ON AND OFF LOADER WHEN HE STRAINED HIMSELF.

EMPLOYEE WAS ST2CKPILING CRUSHKERRUN AT MAIN PLANT HE WAS LOADING A TRUCK UNDER THE BINS WITH CRUSHER RUN WHICH HAS A LEVER TO OPEN THE GATE HE PROPPED IT OPEN WITH AN OBJECT THE GATE CAME LOO SE & STRUCK HIM3ON THE BACK OF HIS ARM HE HAS A CONTUSIONTO LEFT ELBOW WITH TRAUMA TO NERVE

EMP WAS TAKING 5 ROLLER OUT FROM UNDER CONVEYOR BELT BELT WAS SHUT OFF HOWEVER IT CAUGHT THE SIDE OF ANOTHER BELT WHICH WAS RUNNING UNDER IT CAUSING THE ROLLER TO CATCH HIS HAND BETWEEN IT AN A METAL FRAME B9UISED RT HAND AND CUT A GASH BETWEEN THUMB AND INDEX FINGER ON RIGHT HAND REQIRING 8 STITCHES

EMPLOYEE WAS DO3NG REPAIR ON BUCKET LINE AT MAIN PLANT TAKING A V-BELT OFF DRIVE. HE WAS TAKING V-BELT OFF HEAVE BY TURNING V BELT AND SHEAVE WHEN HIS H AND WAS CAUGHT BETWEEN SHEAVE AND V BEL T THIS SHEAVE W3LL NOT TURN BUT ONE WAY SO COULD NOT TURN BACK TO GET HIS HAND OUT.

THE EE WAS HELPING PUT A NEW PART ON CRUSHER. THIS PART WAS TO BE HAMMERED DOWN TIGHT. A PIECE OF METAL CAME OF HAMMER & STRUCK EE IN THE RIGHT SHOULDER.

EMPLOYEE WAS HAULING STONE FROM BINS TO STOCKPILE WITH EUCLID AT MAIN PLANT WHILE UNDER BIN TO LOAD HE WENT TO GET OUT OF TRUCK AS HE STEPPED DOWN FROM TRUCK ONTO CONCRETE HIS FOOT WAS NOT EN TIRELY ON CONCRFETE & HE SLIPPED OFF CONCRETE & DOWN WALL CUTTING HIS LEFT LEG WHICH REQUIRED SUTURES

EMPLOYEE WAS STANDING ROCKER MOTOR BASE UP AGAINST CONCRETE ABUTMENT, HE CAUGHT HIS FINGER BETWEEN THE MOTOR BASE AND CONCRETE. SOFT TISSUE AMPUTATION TIP OF RIGHT INDEX FINGER. NO DEFINITE BO NY ABNORMANLITY IS SEEN. THERE WAS APPARENT AMPUTATION OF THE SOFT TISSUE DISTAL TO THE TERMINAL PHALANX.

EMPLOYEE WAS FUELING HEAVY EQUIPMENT WITH SERVICE TRUCK. HE WAS COMING UP THE HILL OUT OF THE QUARRY WHEN VEHICLE MOTOR STALLED BRAKES DID NOT HOLD AND TRUCK RAN AWAY BACKWARDS DOWN THE HILL, STRIKING SOME ROCKS WHICH OVERTURNED VEHICLE ONTO ITS SIDE. EMPLOYEE SUFFERED CONTUSION OF RIGHT ELBOW BUT DOES NOT KNOW HOW INJURY OCCURRED.

EMPLOYEE WAS HELPING TIGHTEN A CAP SCREW BOLT ON THE 4\ ROCK CRUSHER. WHEN THE WRENCH WENT AROUND, HIS FINGER WAS CAUGHT BETWEEN THE WRENCH AND A METAL BAR. CRUSHED BONE AND TORE NAIL OFF OF L ITTLE LEFT FINGER.

STANDING TOO CLOSE TO EDGE OF HIGH WALL SLIPPED AND FELL ABOUT 24\ LANDING ON SOME LOOSE GRAVEL RECEIVING BRUISES AND ABRASIONS

EMPLOYEE WAS WORKING ON THE CRUSHER FIXING TO TAKE HEAD OFF WITH AN ELECTRIC HOIST.