Waco Plant Metal/Non-Metal

Employee was grinding with a corded 4 1/2" grinder on a dust collector manifold replacement at the maintenance fabricating shop and got a piece of metal in their eye due to flying debris after removing their auto darkening hood and safety glasses.

Employee was cleaning out discharge end of quencher and hurt their ankle in the process, tripping over clinker balls.

While installing a deflection shield for under the redimat, employee was notching the belt to fit correctly around the gate foot with a box cutter. Cutting towards the foot/body, the box cutter slipped and cut employee through EE's work boot and cut into inside part of EE's R foot. Seeked medical care and no stitches or restrictions.

As employee was completing their normal job duties, they were walking up the stairs and they lost their footing and at the same time their knee buckled and went backwards causing their knee to hyperextend back.

Employee was trying to move impact dolly when EE strained EE's Right shoulder

Employee was trying to get the Gypsum feeding unplugged on the bottom of Silo #17. EE was working from a small portable platform. As EE performed the task EE slipped and EE's mouth on the silo cone, causing EE to break EE's Left front tooth.

Employee was helping unchoke south side air slide at the packhouse. EE climbed up on the handrail to hit the side of the air slide box with hammer. The handrail broke causing employee to fall and catch self with right hand. Causing employee to tear/rupture the bicep.

Cut to middle finger on left hand during installation of clay pump housing

Miner was shooting cardox in kiln, inserted the drill bit into the port and when the air valve was turned on hot clinker dust blew back into the miner's face and arms. The miner received first, and second degree burns to face and arms. Miner was treated at ER Clinic and returned to work the same day.

Miner was walking by the bag house and slipped in the wet dust and twisted left ankle when trying to catch self. Weather was cold and wet.

Employee was in the quencher dryer are helping clear a choke up in the kiln throat. Employee was using a sledgehammer to hit the side of the chute. When they struck the chute they felt a discomfort in their upper body.

The miner was removing duct tape from a coupling for KWF-1 using a knife and when the shaft accidentally rolled EE cut EE's left knuckle on EE's index finger and EE needed stitches

The injured employee was walking down the stairwell of the finish mill building when EE fell landing on their right hand.

The injured miner was removing broken bags from under the palletizer area when EE injured EE's lower back.

The injured miner was jack hammering out a choke up in the throat that goes into the quencher dryer when received chemical burns from clinker dust. EE did seek immediate medical attention but the pain got worse later on and they went to an urgent care clinic the next day.

The Injured Miner (IM) was striking a air line when a build up of mud fell striking the IM's hard hat and right shoulder causing neck trauma and chipping a tooth.

The injured process foreman was assisting in shooting out a ring in the kiln with a shot when some material got into right eye.

The injured process attendant IV was washing down the raw mill basement area floor when they slipped on green algae injuring their right knee.

The Injured employee was assisting with removing screens from a raw ball mill when the screen dislodged fell and struck EE's right foot and wrist.

The Miner was removing bars from a cement mold when the screwdriver ee was using slipped and struck left thumb and nail.

The Injured Employee was opening a rail hopper car door with a bar when the bar slipped causing the IE to fall to the ground landing on right wrist.

The injured miner was jackhammering in the quencher dryer and removing the loose material with a shovel. When EE bent over and twisted to remove the material, EE felt a pull in lower back. EE did not seek medical attention until 10/07/2018.

The consultant was eating breakfast in a small conference room when the consultant suddenly collapsed in the chair. CPR was administered until emergency responders and EMS arrived.

The Miner was working on the finish mill chute choke up with a rivot buster. The air hose of the rivet buster moved knocking a 6' bar over striking miner's back causing a bruise. Miner did not seek medical attention until 6/13/2018.

Employee was removing discharge head liner when the liner slid causing the employee to move and lose balance causing EE to fall over on left side. Employee received a laceration to left leg below the knee.

The Maintenance Journeyman was helping to replace a dust collector bag and was pushing in two clips with EE's two index fingers when the other maintenance journeyman lifted the bag the clips mashed both fingers. EE did not seek medical attention until 3/28/2018

The Serviceman was shoveling up cement at the rail unloading station when the Serviceman felt back go out

The Maintenance Journeyman A was bent down vacuuming the compressor room and when the Maintenance Journeyman A raised up felt a pain in lower back. The Maintenance Journeyman A did not seek immediate medical attention until 01/26/2018

While checking a clinker inlet chute the miner was hitting the side of the chute to remove any buildup and had hand resting on the edge of the inspection door when a chunk fell striking right hand against the chute causing a laceration

The injured miner was replacing a door on the side of a screw and was replacing the bar that held the door in place with a hammer when the miner hit left index finger causing a laceration.

The Injured miner was exiting a forklift and when turning to get off felt a sharp pain in the middle of back on the left side

The Maintenance Journeyman A was lifting a troughing roll for a belt conveyor and strained back.

After shoveling around LWF-1 weighfeeder, the miner took a break then complained about a back strain and reported it to a supervisor. Employee did not seek immediate medical attention until 12/27.

The Maintenance Journeyman A was climbing an affixed ladder at the Quencher Dryer Pier when the anchor point broke loose causing EE to fall landing on right shoulder.

The injured employee was cleaning the raw mill area. While shoveling material into the gehl loader bucket, the injured employee turned EE's body to dump the shovel into the bucket, EE felt a sharp pain in EE's upper right hip.

The injured employee was operating a forklift to stack pallets of packaged cement when a fluid cooler fan started vibrating. EE went to adjust the fan guard when finger was cut by the plastic fan blade requiring stitches.

The Quality Control Tech(QC Tech) was assisting with charging a raw mill with grinding media using a 5 ga. bucket. 4/25 ee reported that Dr. diagnosed ee with a hernia. EE was sent to the worker's comp Dr. with an umbilical Hernia. The hernia was cosmetically corrected on July 8.

The injured employee was moving pallets of cement with a forklift. Due to stronger winds from storms sawdust from a pallet blew up under employee's safety glasses and got into employee's eyes requiring prescription drops.

Process Attendant IV was making rounds inspecting the finish mill equipment when they made contact with a beam just under the finish mill area. They reported it immediately to their foreman and their scheduled day off was Monday. They came in Tuesday with a stiff neck asked for medical attention.

The injured employee(IE)was be refreshed in import cement unloading. The IE was assisting opening the hopper door on a railcar. The IE was holding open a locking device on the door inertia caused the door to open and crush is left index finger to smashed by the locking device.

Miner was walking out of the elevator when he bumped his right elbow on the scissor gate. The miner was carrying a box in his arm. He did not have symptoms of swelling until later that night. He called his foreman the next day 7/25/2015.

The Injured Miner was changing the housing cover of CSP-8 pump. It was badly worn and had sharp edges around the bottom of the cover. He grabbed a hold of it to slide it out of the way and the sharp edge sliced his left finger

Employee had just got a sample of flexicoke from a flexicoke trailer and was descending when his foot landed on a chain used to secure the discharge cap to the trailer. This caused him to lose the 3 points of contact and lose his balance causing him to put his weight on his right arm causing pain. As a process attendant he had his required PPE including his fall protection

A Serviceman IV temporarily assigned to the pack house stepped off the forklift to refuel it with propane when he felt pain in his left knee. He was sent back with no restrictions. On 8/6/2015 a specialist reviewed his MRI and put him restrictions.

Injured Employee (IE) removing a chunk of material when some fell off hitting a bar and smashing his left thumb breaking the bone. IE did not request medical attention until December 8th.

Injured Employee (IE) was moving rail car from c-silos to plant; came up on switch and dropped to ground. As IE turned to walk to back of car the gravel gave way and he twisted his left knee, left ankle, left wrist and right ankle

Miner was removing castable from a quencher spout and piece of castable blew into his eye.

Injured employee (IE) was taking off parts from the K5 when the follower plate suddenly came loose and smashed the IE's finger between the pump shaft

Injured Employee(IE) was removing raw mill spout cut bolt and was driving out bolts to remove the spout. The spout moved and made the alignment bar come in contact with his left and the hopper of the raw mill causing bruising. Subsequently a knot or cyst has come up requiring more attention.

Injured Employee (IE) was starting the Cemex unloading system and saw that the system was dusting. He went around to the Cemex Dust Collector while it was still running and opened the inspection port and stuck his right hand inside and contacted with a rotary feeder catching the tips of his two fingers on the right hand and pinching tissue on the ends.

Injured Employee (IE) was removing coating from the kiln throat using a rivet buster. He aggravated his old back injury by binding and pushing the coating down with the throat.

Aqueous Ammonia 19% dripped into his left eye, air lines were contaminated with aqueous ammonia, trying to remove plug on the run under pressure, wind blew it into his eye

Injured Employee (IE) was working on a stretch hood machine. When he stepped off the machine from an access staircase, he twisted his knee. The IE was sent to a specialist which the IE underwent an MRI the MRI came back inconclusive. The IE was sent back to the specialist after reviewing the MRI again and again saying the MRI was inconclusive the specialist recommended therapy.

Injured Employee (IE) was cleaning out a dust collector with his left hand up in dust collector trying to unplug it. The cement in the dust collector broke loose pushing his hand down and his finger got caught in the rotary feeder below.

Injured employee was doing an assembly of a finish mill cement pump parts. The pump is below waist line alot of leaning over lifting parts and strained back

Injured Employee (IE) was cleaning chunks out a 3" hole from a cement silo with a bar and chunk broke up then cement come out and knocked the IE's glasses off and got in his eyes.

Miner was moving a vending machine and smashed his right little finger between machine and door jamb.

Employee was trying to get KCD #2 drag running when some hot raw clinker splashed on to employees left arm causing second degree burns.

Injured Employee (IE) was helping to charge a raw mill with steel balls and was tightening the chain on a Morse drum handler when he felt the pain. He wanted a report filled out but did not seek medical attention until 8/16/2011.

Miner was handing up cages for dust collector bags to re-install them when he felt something in his back.

Miner was opening a door on a cement hopper car and was breaking a cable tie with a large bar. When the cable snapped it jarred both his elbows causing pain.

Miner was repairing a Hercules roller mill plow and was removing a bolt from one of the plows. when he struck the bolt with a hammer cement shot out of the hole and into his face and left eye which was scratched.

Miner was rebuilding a hercules mill roll for installation and was using a 3# hammer to drive a bolt into place and after several minutes of swinging the hammer he felt a pop in his lower back.

Miner was removing broken parts of a die ring from a hercules mill and strained his lower back

While doing a brick job and putting in the key row the brick moved and smashed his right hand small finger breaking the tip of the finger.

Miner was helping to remove a guard at the end of a Raw Grinding Mill and said he felt some discomfort in his back but did not want medical attention at the time. 1/14/2011 Miner was having some back spasms and requested to see a dr. Dr diagnosed a sprain on the right side of his back.

Miner was inspecting outfall #1 from the source, slipped and fell in the mud and felt pain in both shoulders and arms. Dr. released him with no restrictions 8/26. 9/2 Dr. released with no restrictions set up MRI appointment 9/4/10. Specialist visit 10/5 Dr put him on restricted duty of use of right arm.

Miner was hauling clinker from end of quencher dry with a skid steer loader and had a chemical reaction burn from the clinker dust.

Miner was manually moving by hand, a bucket elevator by sheave and pulley to position elevator sprocket into a workable position when his pinky finger was caught between the sheave and the belt and the tip of the finger was broken.

Miner was charging Raw mill with steel balls. He cut the band that held the lid of the barrel and when the band came loose it hit his forearm cutting it requiring 2 stitches.

Due to repetitive motion which includes loading the cement packing machine with empty bags and operating a forklift. carpal tunnel syndrome was deemed as a work related injury on May 18th. Day surgery was done on May 20th.

Miner was using a 50 lb weight to calibrate a scale belt when he said he felt something in his back. The initial visit did not reveal anything and he returned to work. During an economic lay-o ff he went to a third doctor who discovered 2 disc protrusions in his back and he did not return to work from lay-off on December 14th.

Miner was tracing air line for a dust collector slide gate actuator. He closed a valve to begin removing a cam locked air hose fitting. When he grabbed the connection, the air line broke at the valve and blew debris that was in the line into his face.

Finish Mill work was being done, when some equipment was being removed, creating a hole. The miner was tracing water lines, when he stepped into the hole falling to the same level, causing a fracture in the wrist and bruised his chin and leg. They were in the process of covering the hole when the accident occurred.

Crush & laceration of right ring finger, no broken bones, loss of fingernail. Required 5 stitches. Gentleman had 2 beams rigged together & was flagging with other hand. Had one hand on beams as lift was being made & finger was caught between beams.

Miner was holding a shaft for a 2" slurry with a pipe wrench while another miner removed the nut on the impeller end. The wrench came loose striking the miner's middle finger breaking it in three (3) places.

While removing a coupling on a shaft of cement pump, miner used a jackhammer bit as punch. As he was striking the bit, a piece of metal sliver splintered off and struck victim in the arm. The doctors original diagnoses stated that nothing needed to be done, but later due to discomfort, the miner requested that the object be removed and the surgery was performed on July 30th.

Miner was stepping down off a clinker platform after trying to locate a clinker chunk; when he was about 4' off of the platform level the miner fell on his side. He was helped up by the process attendant. Within the next couple of minutes he passed out and hit his head on the platform grating causing a laceration requiring stitches

While replacing screens in the raw mill a screen fell on the back of the victim's leg and it took assistance from another miner to lift it off. The strain of lifting the screen caused a herniated stomach. He is on light duty at this time but will require surgery at a later date. The screen was placed improperly on the uneven ball charge causing it to fall over.

The victim was observing a auto stretch film operate to determine why the knife was not cutting the film when he went to check the knife because it was jammed. Before de-energizing the equipment or checking for stored energy the victim unjammed the blade from the guard causing the knife to cut his thumb and thumb nail requiring 3 stitches.

Miner was replacing 3/4" steel air line and valve. When he was replacing damaged valve, compressed air in the line blew rust into his left hand. He had isolated the damaged valve with a second valve. The second valve appeared to be completely closed, but was not closed.

Miner was installing a 3/8" metal plate on the bottom of a drag conveyor. The injured was using an aligning bar to put bolts in the bottom. He was laying on his side & moving the bar when he felt a burn. It was not reported that day to a foreman or supervisor. The next day he came in & complained about the pain.

Miner was removing a 10" pipe elbow that was originally installed using silicone as as a gasket. While using pressure with a forklift fork to break the elbow loose, it broke loose and fell onto the miners right hand cutting the right hand knuckle requiring stitches and broke his small finger on his right hand.

The administrative Assistant was moving a box of files when her left foot caught on a chair mat causing her to put out her right foot for balance. The heel of the right foot came off of the shoe causing an in place fracture of the foot.

WAS INSTALLING A CHAIN GUARD. GUARD SLIPPED AND CAUGHT RING FINGER ON LEFT HAND BETWEEN TOP AND BOTTOM OF GUARD.

EMPLOYEE WAS OPERATING SMALL DRILL PRESS IN MACHINE SHOP, HE WAS DRILLING 4 SMALL HOLES IN A 3X3PIECE OF METAL. AS EE DRILLED LAST HOLE, THE METAL PIECE CAME LOOSE FROM THE VICE CAUSING THE ME TAL TO MOVE STRIKING THE PALM OF LEFT HAND.

EMPLOYEE WAS USING A JACKHAMMER. A THROTTLE VALVE SPRING CAME OFF JACKHAMMER AND HIT CONCRETE THEN BOUNCED OFF AND HIT EMPLOYEE ON CHIN CAUSING LACERATION.

EE WAS FUELING A PROPANE TANK ON FORK TRUCK. THE TANK GAUGE SHOWED FULL. EE SHUT OFF MAIN VALVE TO FILL TANK & SHUT OFF VALVE TO FORK TRUCK TANK. AS HE STARTED TO REMOVE FILL HOSE FROM FORK TR UCK TANK, PROPANE ESCAPED FROM PROPANE HOSE CONNECTION SQUIRTING INTO HIS EYE.

EE WAS ATTEMPTING TO OPEN A RAIL CAR DOOR WITH CROW BAR. THE BAR SLIPPED CAUSING EE TO FALL AGAINST RAIL CAR. AS HE FELL HIS RT. HAND CAUGHT HIS WEIGHT AND HE JAMMED HIS HAND & INDEX FINGER.

EE WAS RAISING GATE ON SILO #14 WITH PRY BAR. BAR SLIPPED, HITTING RT. INDEX FINGER. EE LOST NAIL AND HAD LACERATION THAT REQUIRED 2 STITCHES.

KILN WAS DOWN. EE ENTERED KILN TO MAKE SURE KILNWAS IN CORRECT POSITION FOR MEN TO WORK ON IT. STEPPED INTO HOT KILN FEED, NOT REALIZING IT HAD NOT COOLED SUFFICIENTLY, AND BURNED BOTH FEET.

EE WAS IN THE MAN ELEVATOR GOING UP TO THE TOP OF A SILO. HIS #2 HAMMER FELL THROUGH THE PASSENGER ELEVATOR'S ACCORDIAN STYLE DOOR. THE HAMMER HANDLE EXTENDING OUTSIDE OF THE RISING ELEVATOR HIT ONE OF THE FLOORS AND FLIPPED INTO THE AIR, STRIKING HIM ON THE LEFT SIDE OF HIS FACE.

EMPLOYEE WAS HAMMERING. LEANED OVER TO SET HAMMER DOWN. LEANED SO FAR THAT HARD HAT FELL OFF HEAD, REACHED TO GRAB IT BEFORE IT HIT GROUND. AS EMPLOYEE STOOD UP, HEAD HIT A PLUG AND CUT HEAD, REQUIRED 11 STAPLES.

INJURED WAS REMOVING SMALL BALLS FROM GATES INSIDE BALL MILL WITH HAMMER AND CHISEL. SMALL PIECEOF BALL CAME OUT OF GRATES, CUTTING LEFT BACK OF HAND THROUGH GLOVE.

INJURED WAS CHECKING MOTOR ON PALLETIZER DUE TO FAILURE. PALLETIZER OPERATED AND THE PRESS ELEMENT OF THE PALLETIZER CAUGHT HIS RIGHT HAND CRUSHING THE ENDS OF 3 FINGERS, REMOVING LAST JOINT O F SMALL FINGER AND RING FINGER.

EMPLOYEE STANDING ON PLATFORM TWISTED RIGHT KNEEHAD ARTOSCOPIC KNEE SURGERY 12-29-99.

EMPLOYEE WAS CLEANING UP SPILL AT LIMESTONE RECLAIN TUNNEL. HE WAS WEARING RESPIRATOR DUE TO DUSTY CONDITIONS. EMPLOYEE HAD A COLD FOR THREE DAYS PRIOR TO ACCIDENT. EMPLOYEE DIAGNOSED AS ASTHM A AND BRONCHITIS.

EE UNLOADING RAIL CAR. STEPPED BACK OF RAIL CAR LOADDER-STOPPING ON RIDOE ON GROUND CAUSING HIM TO LOOSE BALANCE FALL BACKWARDS. CAUGHT AMSTIF WITH ARMS-BAFAMING LEFT WRIST. THOUGHT IS WAS A S PRAIN UNITL 10-6-99 WHEN HE WENT TO DR. DR DIAGNUOISED AS FRACTURE.

DRIVE PIN BACK IN LOADER BUCKET WITH SLEDGE HAMMER, CAUGHT RIGHT THUMB BETWEEN HAMMER HANDLEAND BUCKET CAUSING INJURY.

INJURED WAS PERFORMING MAINTENANCE ON 48" BOX FAN. GUARD WAS REMOVED FOR MAINTENANCE. INJURED ATTEMPTED TO ADJUST DRIVE WITH FAN RUNNING. INJURED CAUGHT HIS RIGHT HAND IN FAN. LACERATIONS TO R IGHT/MIDDLE & RING FINGER. TOTAL 9 STITCHES.

INJ CHECKING OPERATION OF DRIVE MOTION OF CEMENTPALLETIZER LAY OUT TABLE. INJ LEFT ARM WAS CAUGHT IN THE MACHINE WHEN THE TABLE MOVED. LAYOUT TABLE MOVEMENT CAUSED INJURY Y

CUTTING TOP OUT OF 55 GAL DRUM OF STEEL BALLS, CUT RIGHT INDEX FINGER WHILE REMOVE DRUM TOP.

TORE FINGERNAIL LOOSE ON LEFT RING FINGER-BY GETTING FINGER CAUGHT BETWEEN SLEDGE HAMMER AND ANGLE IRON HE WAS DOING FEED TO SILO 23. DR SEWED FINGER NAIL BACK ON.

INJURED WAS WORKING ON SUMP PUMP IN SLURRY PUMP HOUSE ON 6" ELEVATED PLATFORM. AS HE WAS STEPPING OFF PLATFORM HE TRIPPED AND FELL BACKWARDS STRIKING THE BACK OF HIS HEAD ON STAIRS CAUSING CUT TO BACK OF HEAD.

INJURED WAS ADJUSTING FORKS ON PALLETIZER TO ACCEPT PALLOT WITH DIFFERENT HEIGHT. FINGER CAUGHT BETWEEN PALLET & FORKS OF PALLETIZED.

AN OUTSIDE TRUCK DRIVER FROM CHEMICAL EXPRESS WAS ROLLING TARPING STRAPS TO TARP LOAD OF PALLETIZED CEMENT AT LEHIGH CEMENT LOADING AREA. HE BACKED UP INTO AREA USED TO LOAD SECOND TRUCK AS FO RK LIFT OPERATOR WAS BACKING UP. FORKLIFT BACKEDINTO INJURED AND FORKLIFT TIRE HIT INJURED'S ANKLE AND BROKE LEFT ANKLE.

IN EXITING TRUCK, DRIVER SLIPPED OFF GRID [STEP] & HIT RIGHT ELBOW.

EMP GOT RIGHT INDEX FINGER CAUGHT BETWEEN FORKLIFT BASKET AND PIECE OF CONDUIT. PINCHED FINGER CAUSING LACERATION WHICH REQUIRED SUTURES.

MECHANIC WAS ASSISTING ANOTHER ONE THE CRANE AND CAUGHT HIS TWO FINGERS IN BETWEEN A CABLE AND PULLEY AND SMASHED HIS FINGER TIPS. BRUISED UP ENDS PRETTY GOOD. HE IS DOING FINE AND CONTINUES T O WORK IN DALLAS.

EE ATTEMPTED TO MOVE ELECTRICAL SWITCH GEAR BY DRAGGING WITH ROPE. ROPE BRATICE EE FELL HIT LEFT CAR ON DOOR JAM. REQUIRED A STITCHES.

EE WAS DESENDING STEPS TO FLAT CLEAN CONCRETE FLOOR. STEPPED ON FLAT CLEAN CONCRETE FLOOR, TURNED TO RIGHT & FELT SHARP PAIN IN BACK. WORKING ON RBC-1.

EMPLOYEE LIFTED USED BEARING FROM SHELF AND THREW IN TRASH CONTAINER. HE FELT SHARP PAIN IN ABDOMEN. WENT TO DR.- DR SAID PULLED MUSCLE POSSIBLE. CONTINUE TO HURT WENT BACK TO DR AND FOUND UMB ILICAL HERNIA WHICH REQUIRED SURGERY 3-15-96.

EMPLOYEE WAS JACKHAMMERING HARDENED MATERIAL FFROM KILN CHAIN HANGERS/ OINT JAMMMED INHANGER. AS EMPLOYEE ATTEMPTED TO PULL OUT OF DAM. FELT A PAIN IN LOWER BACK..

EMPLOYEE WAS SHOVELING CEMENT DUST OUT OF KILN MAN HOLE. WIND BLEW DUST IN EYE (EMPLOYEE WS WEARING SAFETY GLASSES WITH SIDE SHIELDS).

INJURED WAS CLIMBING UP FRONT STEP OF CAT 769B TRUCK WHEN HE TWISTED HIS LEFT KNEE. HE WAS ASSISNGED TO HAUL CORE.

WELDING HANDRAIL BACK INTO PLACE- FALL- FRACTURED RIGHT FOOT.

INJUR ED WAS TIGHTENING BOLTS FOR SPEED R EDUCER COUPLING WHEN WRENCH SLIPPED & HE STRUCK HIS RT THUMB AGAINST THE SPEED REDUCER CUT THUMP REQUIRE 5 STICHES

INJURED WAS CHANGING DISCHARGE VALVE ON THICKENER WHEN THE VALVE FELL OFF THE STAND AND CAUGHT HIS LEFT THUMB AND HURT HIS LIGAMENT.

EMPLOYEE WAS LOADING BULK TRUCK. WENT DOWN STAIRS TO ADJUST FEED RATE. TRIPPED ON AIR HOSE AT BASE OF STAIRS. HIT HIS FOOT AND KNEE.

INJURED WAS PULLING DOWN ON A 6FT BAR IN A STANDING POSITION WHEN INJURED FELT A SHARP PAIN IN HIS LEFT SIDE INJURED WAS WORKING ON A HERCULES MILL

EMPL SITTING ON BEAM AT CLAY WASH MILL AND LEANED DOWN TO PULL UP A BROKEN CHAIN-ABOUT 50 LBS.FELT A SHARP PAIN IN LOWER BACK.BACK MUSCLE STRAIN

EMPLOYEE WAS USING CUTTING TORCH TO BURN STEEL BALLS FROM CREVICES IN BALL MILL MATERIAL SPLATTERED BACK & A STEEL PARTICAL GOT AROUND CUTTING GOGGLES & INTO RT EYE

DESCENDING STAIRS WHEN BOTTOM STEP GAVE WAY. STRUCK LEFT KNEE AGAINST HANDRAIL POST. WENT TO ASAP CLINIC SAME DAY- DIAGNOSIS OF STRAINED KNEE. LAST WEEK SAID KNEE WAS STILL HURTING. WENT TO AS AP CLINIC 2-13 AND ORTHOPEDIC SURGEON 2-14. IS PRESENTLY TAKING THERAPY. NO LOST TIME AND NOT RESTRICTED WORK ACTIVITY TO DATE.

EMPLOYEE ADVISED SUPERVISOR 4-17-91 THAT HIS BACK HAD BEEN HURTING SINCE 4-15-91. HAD NO RECOLLECTION OF ANY SPECIFIC ACTIVITY THAT TRIGGERED PAIN. HAS BEEN OPERATING A SMALL FEL AND DOING C LEANUP WITH A SHOVEL AND BROOM. DOCTOR DIAGNOISED MID BACK STRAIN AND PUT EMPLOYEE ON LIGHT DUTY.

INJURED AND COWORKER WERE REMOVING CHUNKS FROM A DUST COLLECTOR HOPPER. COWORKER WAS USING A METAL BAR TO HIT ON HOPPER. INJURED SUDDENDLY MOVED HIS HAND AND IT WAS HIT BY THE BAR.

INJURED AND CO WORKER WERE REMOVING STEEL COVER PLATES FROM A DRAIN ROUGHT IN ROADWAY. PLATE WEIGHTED 161 LBS. INJURED WAS IN PROCESS OF TIPPING PLATE FROM OVER DRAIN TO BESIDE DRAIN WHEN HE L OST CONTROL AND IT TIPPED ONTO HIS FOOT. IT BROKE HIS RIGHT BIG TOE.

EMPLOYEE WAS ENTERING A DARK LOAD CENTER AND TRIPPED. WHILE FALLING, HE REACHED OUT AND HIS LEFT HAND CAME IN CONTACT WITH A BREAKER DOOR. THE DOOR CUT THE SMALL FINGER ON HIS LEFT HAND REQUIR ING TEN STITCHES.

INJURED SPENT THE DAY WELDING STEEL PLATES TOGETHER. AT 11:00 PM HE CALLE DHIS SUPERVISOR AND STATED THAT BOTH EYES WERE BURNING. HE WAS TAKEN TO THE HOSPITAL EMERGENCY ROOM TREATED AND RELE ASED.

EMPL WAS INSIDE VAN INSTALLING EMPTY PALLETS ALONGSIDE CEMENT PALLETS TO KEEP LOAD FROM SHIFTING. EMPL BRUSHED AGAINT PIECE OF BANDING MATERIAL THAT WAS PROTRUDING FROM SIDE OF VAN. HE SUSTAIN ED DEEP LACERATION BELOW KNEE OF LEFT LEG.

EMPL WAS PART OF CREW USING ELECTRIC HOIST TO LIFT MANHOLE COVER UP INTO BALL MILL. EMPL WAS SITTING ON FLOOR PUSHING COVER WITH FEET TO GUID IT THROUGH MANHOLE. DEAD END OF HOIST CABLE CAME L OOSE & COVER FELL ON EMPL'S LEGS PINNING HIM TO THE FLOOR.

EMPLOYEE WAS INSIDE A ROATERY COLLER USING A 90LB JACKHAMMER TO REMOVE REFRACTORY LINING.THIS WAS THIRD DAY OF THIS JOB.NORMALLY WORKS AS A CONTROL ROOM OPERATOR.EMPLOYEE EXPERIENCED PAIN IN L OWER BACK CAUSED BY THIS MORE STRENIOUS THAN NORMAL WORK.

EMPLOYEE HADN CLIMBEDA VERTICAL LADDER SEVERAL TIMES IN THE PAST TWO DAYS TO GET INSIDE A 31 FOOT HIGH TANK TO REPAIR IT'S RAKES. THIS EXTRA ACTIVITY AGGRAVATED A PREVIOUS KNEE CONDITION.

EMPLOYEE STEPPED UPON HANDRAIL & REWACHED OVER FENCE GUARD & ATTEMPTED TO TIGHTEN BRACKET BOLTS ON PROXIMIT Y SWITCH FOR PADDLE STOP AS EMPLOYEE TIGHTENED BOLTS WITH RT HAND PADDLE CAME AROUND & STRUCK EMPLOYEES LEFT ELBOW THIS RESULTED INA CUT THAT REQUIRED SEVERAL STITCHES

BRICK HAD BEEN KNOCKED DOWN FROM KILN AND LOADED INTO A WHEELBARROW TO BE REMOVED FROM KILN. AS EMPLOYEE WAS LIFTING UP ON WHEELBARROW HE FELT A SHARP PAIN IN HIS RIGHT GROIN.

EMPLOYEE WAS STANDING ON A PILE OF MATERIAL REMOVING A HOPPER DOOR.AS EMPLOYEE REMOVED A BAR HOLDING THE DOOR,THE FORCE OF THE MATERIAL INSIDE THE HOPPER PUSHED EMPLOYEE BACK AGAINST THE HANDR AIL.FIRST DOCTOR VISIT 09-29-89.

INJURED WAS LOOSENING BOLTS ON A WIFLEY PUMP WHEN THE WRENCH SLIPPED AND HE CAUGHT HIS FOOT IN A DRAIN CAUSING HIM TO STRAIN HIS RIGHT KNEE.

EMPLOYEE REPORTED LEG PAIN & WENT TO HIS PERSONAL DOCTOR 7/25/89. HE THINKS IT MIGHT HAVE BEEN CAUSED BY A SLIP ON ABOUT 7/18/89. NO PAIN UNTIL 7/20/89. SECOND DOCTOR VISIT WAS ON 7/31/89. AT THIS TIME DR. RECOMMENDED THERAPY AND SUSPECTS ABACK PROBLEM. EMPLOYEE HAS NOT LOST ANY TIME TO DATE.

INJ USING IRON BAR TO PRY OPEN RR CAR DOOR.JUMPED ON BAR TO BREAK OPEN DOOR AND STRAINED RIGHT GROIN AREA.

INJURED HAD BEEN OFF WORK DUE TO A DISLOCATED SHOULDER FROM AN ACCIDENT AT HIS HOME. HE WAS RELEASED TO RETURN TO WORK 4/17/89. HE REACHED TO PICK UP A 36" PIPE WRENCH AND FELT PAIN IN HIS RIG HT SHOULDER.

EMPLOYEE SAT ON A BUILD UP OF CLINKER & RAW MATERIAL TO ENABLE HIM TO REACH A BUILDUP UNDER LBC-4 HEET CONVEYOR. MATERIAL WAS WET DUE TO RECENT RAINS, RESULTING IN CHEMICAL BURNS TO RIGHT & LE FT BUTTOCKS.

EMPL WAS ATTEMPTING TO REMOVE BAG FROM ROLLER CONVEYOR AS HE LIFTED BAG AND TRNED WITH IT TO DUMP IN HOPPER HE FELT PAININ R KNEE

EMPLOYEE WAS RETURNING FROM CHECKING ANALYZER IN KILN LOGHOUSE. HE SLIPPED AND FELL SIDEWAYS DUE TO DEBRIS ON FLOOR, THUS TWISTING HIS ANKLE. THERE WAS NO APPARENT PROBLEM UNTIL ABOUT A WEEK L ATER. AT THAT TIME HE REPORTED THE INCIDENT TO HIS FOREMAN AND WAS SENT TO THE DOCTOR.

EMPLOYEE AND CO-WORKER REMOVED PUMP FROM BASE AND LIFTED IT ACROSS 4BC-4 BELT TO WEST SIDE. INJURED LIFTED OLD PUMP AND CARRIED IT OUT OF THE TUNNEL. HE ATTRIBUTES THIS TO HAVING A STIFF BAC ACK THE FOLLOWING MORNING.

EMPLOYEE WAS PU5LING BY PASS SIDE WITH A COME-A-LONG, SLIDE WAS STUCK.AFTER GENERAL ATTEMPTS SLIDE CAME LOOSE SUDDENLY, CAUSING EMPLOYEE TO LUNGE AND TWIST KNEE.

CO-WORKER WAS U8ING CUTTING TORCH TO WORK ON SCREEN SCREW. INJURED PICKED UP TORCH HOSE TO FREE IT FROM HANGING ON METAL. HOSE BROKE AT POINT WHERE INJURED WAS HOLDING IT. THERE WAS A FLAME A ND INJURED'S HA3D WAS BURNED.

CO WORKER WAS D9IVING A PICKUP TRUCK WITHA WELDING MACHINE IN TOW. AFTER CO-WORKED HAD PARKED PICK UP INJURED DISCONNETED WELDING MACHINE FROM PICKUP AND STARTED WALKING BACK TO THE ROW MIN AR EA. WHILE DRIVE9 OF PICKUP WAS IN THE PROCESS TURNING AROUND HE BACK UP AND STRUCK INJURED IN THE BACK CAUSING INJURY.

AFTER DESCENDIN1 STAIRS TO GROUND LEVEL INJURED STEPPED ON BOARD THAT HAD BEEN PLACED IN MUDDY AREA. BOARD WAS SLICK AND INJURED SLIPPED AS HE STEPPED ON BOARD. HIS LEG EXTENDED OUT CAUSING STRAIN. 3

INJURED WAS CLE5NING FINISH MILL LINERS. ASHE WAS MOVING A INER ANOTHER LINER THAT WAY LAYING LOOSE SLIPPED AND STRUCK INJURED ON UPPER RIGHT SHIN.

INJURED WAS STA3DING OUTSIDE CLOSE TO #2 FLUE DOOR. CO-WORKING WAS USING 12 GAUGE SHOTGUN WITH SLUG TO SHOOT INTO SMALL OPENING FROM THE GROUND LEVEL. SLUG DISINTEGRATED & SOME SMALL PIECES ST RUCK INJURED ON3HAND & ARM.

CO-WORKER LIFTI3G 55 GALLON DRUM OF HYDROPHOBE USING A FORKLIFT. INJURED WAS HELPING TO LINE UP DRUM IN STORAGE RACK. WHEN BAREL WAS PLACED IN RACK INJURED'S HAND WAS CAUGHT BETWEEN RACK & EDG E OF DRUM. 3

MOVING BURNER P3PE INTO KILN.BURNER PIPE IS MOUNTED ON RAILS.INJURED WAS PULLING ON CHAIN WHICH OPERATOR A WRENCH.CHAIN WERE HARD TO MOVE AT FIRST THEN TENSION EASED AND INJURED RECEIVED STRAI N BY SUDDEN MOV9MENT.

CLEANING UP PIL9 OF SPILLER CLINKER ATTEMPTED TO PULL PIECE OF SCRAP METAL OUT OF CLINKER PILE STEPPED ON PIECE OF LOOSE CLINKER AND LOST HIS BALANCE RESULTING IN A FALL WHEN HE FELL HE T WIS HIS BACK CAUSIN1 STRAIN

INJ PERFORMING 9LEC REPAIR WORK ON CEMENT COOLER.WALKING BESIDE COOLER STRUCK RIGHT SHOULDER AGAINST JUNCTION BOX MOUNTED ON WALL.

INJURED WAS WAL5ING DOWN CONVEYOR BELT TUNNEL WHICH WAS ON AN INCLINE STEPPED ON A SMALL ROCK ON CONCRETE. HE SLIPPED & TWISTED HIS KNEE.

INJURED WAS WAL5ING UP STAIRS. HIS RIGHT FOOT STRUCK FRONT OF STEP. HIS RIGHT KNEE GAVE WAY AND HIS RIGHT KNEE STRUCK STAIR STEP.

INJURED WAS REPLACING DAMAGED BAGS IN DUST COLLECTOR INJURED AND COWORKER ATTEMTED TO RAISE A 30 FT X 11 FT DIAM FIBER GLASS BAGS THAT HAD FEL FILLED WITH DUST AND HAD FALLEN WHILE PULLING O N ROPE THAT HAD BEEN ATTACHED TO BAG HE FELT A PAIN IN HIS BACK HE CONTINUED TO WORK UNTIL 9-12-85

INJURE WAS OPERATING JACKHAMMER TO REMOVE OLD CASTABLE FROM TOP SIDE OF I.D. FAN END OF AIR HOSE BECAME DETACHED FROM COUPLING WHILE ATTEMPTING TO GRAB END OF AIR HOSE HE WAS STRUCK IN THE GR OIN BY END OF HOSE DID NOT MISS WORK UNTIL 5-10-85

INJURED WAS WORKING INSIDE QUINCHER DRYER OPERATING A 60# JACKHAMMER TO LOOSEN HARD BUILDUP OF MATERIAL ONSIDE OF DRYER. AS MATERIAL BROKE LOOSE JACKHAMMER SLIPPED DOWN SIDE CAURVED DRYER STRI KING INJURED ON LEFT FOOT

INJURED STEPPED OFF OF MOTOR BEARING AFTER OPERATING COME-A-ALONG TO LIFT COUPLING COVER. HE SLIPPED AND FELL. WHILE FALLING HE GRASPED SOMETHING WITH HIS LEFT HAND. THE WEIGHT ON LEFT HAND CAUSED LACERATION.

INJURED & COWORKER WERE CONSTRUCTING FORMS TO POUR CONCRETE WALKWAY INJURED STEPPED 18IN OFF AN D STEPPED 18IN OFF ANOTHER WALKWAY AND AS HE HIT THE GROUND HE SLIPPED SLIGHTLY & FELT BURNING SENSATION HE WORKED UNTIL FOLLOWING FRI & RECEIVED MEDICAL ATTENTION