Mary Lee No 2 Mine Coal

EMPLOYEE STEPPED ON EDGE OF CONCRETE SLAB & TWISTED HIS ANKLE & FX FOOT

EMPLOYEE WAS JACKING JEEP BACK ON TRACK WHEN THE JACK SLIPPED & EMPLOYEE FELL.

A FALL OF ROOF OCCURRED ON BELTLINE IN THE 425 #1 ENTRY AT SPAD 32 + 4D. SIZE WAS 25 X 18 X 3-1/2. WE WILL CLEAN UP FALL AND REBOLT.

A FALL OF ROOF OCCURRE DON 450 MAIN LINE BELT AT SPAD 32+30 SIZE WAS 20X50X5 AREA HAD BEEN BOLTED WITH 36" B HAM BOLTS.

A FALL OFF ROOF OCCURRED ON SECION 4445 IN THE RETURN AIR COURSE AT SPAD 1&20 THE SIZE WAS 60X20X51/2 IT HAD BEEN BOLTED WITH 36 INCH B HOUR BOLTS.

EMPLOYE EWAS WORKING ONBATTERY CRUSHER LID FELL AND CAUGHT HIS HAND.

THE EMPLOYEE WAS DRIVING A BEARING ONTO MIENR WHEN HE HIT HIS THUMB WITH THE HAMMER.

EMPLOYEE WAS SHOVELING ON BELT, THE BELT STOPPEDAND THE EMPLOYEE STARTED TO CROSS THE BELT, IT STARTED UP AND THREW HIM OFF.

EMPLOYEE WAS HELPING MOVE POWER CENTER WHEN A PIECE OF ROCK FELL FROM THE TOP & STUCK HIM ON THE HEAD & SHOULDERS.

EMPLOYEE WAS SCALING ROCK & TWISTED HIS RT KNEE BY STEPPING ON A PIECE OF SCALE ROCK.

A FALL OFROOF OCCURRE DON 425 TRACK AND BELT, AT SPAD 37+30. SIZE 60X24X4 1/2 AREA HAD BEEN BOLTED WITH 36 IN BOLTS.

EMPLOYEE WAS HELPING LOUD A 2 WHEEL CART AND FELT IT SWING OVER AND HIT HIS LEG AGAINST HE FALT CAR.

A FALL OF ROOF OCCURRED IN THE BELT HEADING OF 450 AT SPAD 22 AND 00 SIZE WAS 40 X 24 X 5 1/2 AREA WAS SPINNED WITH 42 IN BOLTS STRATA WAS LAW SANDY SHALE.

EMPLOYEE WAS HELPING LAY TRACK WHEN ONE OF THE RAILS FELL ON HIS FOOT

EMPLOYEE WAS LIFTING MOTOR OFF JEEP WITH ROCK BAR WHEN HE GAT A PAIN IN HIS SHOULDER. HE RE-INJURED ON 8-26-93 REACHING FOR SUPPLIES HE WENT TO DR ON 8-26-93.

EMPLOYEE WAS CLEANING ON BELT. HE BENT OVER AND GOT A CATCH IN HIS BACK.

EMPLOYEE WAS SPLICING CABLE & HIT CABLE RING WITH HAMMER & A PIECE FLEW OFF & STRUCK HIM IN THE HAND

EMPLOYEE WAS JACKING TRACK OVER WHEN JACK LEVER SLIPPED AND HIT HIM IN THE CHEST.

WHILE CHANGING BATTERIES, JUMPER CABLE FIRED UP AND BURNED FINGER.

EMPLOYEE WAS GETTING OFF RAM CAR TRAILER WHEN HE SLIPPED AND FELL.

EMPLOYEE WAS CLEANING HEADER AND FELL OVER TIE DOWN STAND.

EMPLOYEE WAS WORKING ON SECTION WHEN SMALL ROCK FELL FROM TOP AND HIT HIS ARM.

RAM CAR TRAILER HIT ANKLE 12-09-92 SPRAIN AGAIN 12-15 -93 & SPRAINED AGAIN 06-14-93 WHICH WAS T HE FIRST DAY HE MISSED

EMPLOYEE WAS PUSHING CART LOAD OF HEADER SCREENS ONE SLIPPED & CUT HIS HAND

EE WAS RUNNING RAM CAR WHEN HE HIT A ROCK AND THRU HIM INTO CANOPY HURTING BACK.

EMPLOYEE WAS LOADING EMPTY ACETYLENE TANK ONTO TRACK JEEP WHEN IT SLIPPED AND CAUGHT HIS HAND.

EMPLOYEE WAS GING THROUGH DOOR THAT HAD A LOT OF PRESSURE ON IT SHE FELL CAUSING INJURY

EMPLOYEE WAS CHANGING BATTERY ON RAM CAR WHEN THE CABLE AREA AND BURNED HIS HAND.

EE SLIPPED ON LADDER WHILE GETTING IN FRONT END LOADER.

EMPLOYEE WAS LOADING BELT ROLLERS ONTO FLAT CAR AND GOT A CATCH IN HIS BACK.

EMPLOYEE WAS LIFTING A DRUM OF OIL AND GOT A PAIN IN HIS BACK. HE DID NOT BECOME LTA UNTIL 5-7-93.

EMPL WAS RIDING IN RAM CAR TRAILER WHEN IT HIT ABUMP THROWING HIM INTO THE TOP.

EMPLOYEE PLACED OPEN POCKET KNIFE ON TOP OF DUST BOX AND TURNED AND CUT HIS ARM ON IT.

EMPLOYEE WAS HELPING MOVE TRACK OVER RAIL WAS ON TRACK JACK & SCOOP BUMPED IT & IT FELL ON EMPLOYEES FOOT

EE WAS STRETCHING BELT ROPE WHEN IT SLIPPED AND HIT HIS KNEE.

EMPLOYEE WAS OPERATING MINER FROM REMOTE POSITION WHEN A PIECE OF DRAW ROCK FELL AND STRUCK HIM ON RIBS AND BACK.

EMPLOYEE TRIPPED GETTING OUT OF TRACK JEEP AND TWISTED KNEE. THIS EMPLOYEE HAD 4 DAYS TURNED IN AND ONLY BECAME A LOST TIME ON 1-4-93.

ANOTHER EMPLOYEE WORK HOLDING PANEL WITH ROCK BAR WHEN IT SLIPPED AND HIT HIM IN EYE.

EMPLOYEE WAS REMOVING RAM CAR TIRE WHEN HE GOT A CATCH IN HIS BACK.

EMPLOYEE BENT OVER TOOL BOX TO REMOVE SOEMTHING WHEN HE GOT A CATCH IN HIS BACK.

EMPLOYEE WAS RIDING ON PORTAL BUS WHEN IT RAN INTO MOTOR ON TRACK.

EMPLOYEE WAS PULLING MINER CABLE AND SLIPPED AND FELL, EMPLOYEE DID NOT GO TO DR UNTIL 1-12-93 CAME BACK TO WORK ON 1-13-93 OFF FOR OPERATION ON 1-27-93.

EMPLOYEE WAS CHANGING OUT RAM CAR BATTERY, SUDDEN MOVEMENT OF BATTERY CAUGHT HIS THUMB BETWEEN BATTERY AND HOOKING ARM.

EMPLOYEE WAS UNLOADING TIMBERS FROM TRACK JEEP WHEN ANOTHER TRACK JEEP ROLLED BACK INTO HIM CATHCING HIS LEG BETWEEN THE JEEPS.

EMPLOYEE HIT HIS HEAD ON T-BOARD WHILE WALKING IN OLD WORKS THIS EMPLOYEE DID NOT BCOME A LOT OR REPORTABLE UNTIL 1-6-93.

EMPLOYEE WAS PINNING WHEN THE PIN STEEL FELL OUT OF THE HOLE AND HIT HIS FINGER.

A FALL OF ROOF OCCURRED ON SEC 4225 IN HEADING AT THE FACE SPAD #15+00 SIZE WAS 20' X 30' X 8' AREA WAS BOLTED WITH 36 IN BLUM BOLTS.

A FALL OF ROOF OCCURED ON THE BELTLINE AND TRACK 3 X CUTS IN BY 425-3 BELT HEADER. THE SIZE OF FALL WAS 20" X 24' X7' TOP WAS LAM SANDY SHALE.

38509NJURED WAS LIFTING BATTERY LID WHEN HE FELT PAIN IN HIS BACK.HE DID NOT DESIRE MED ATTENTION AT TIME OF INJURY AT END OF SHIFT.HE CALLED THE MINE THE FOLLOWING DAY 08-12-92 FOR DR REFERRA 30344BAR NERVE ROOT COMPRESSION DIAGNOSED CHIROPRACTOR.

54736YEE SLIPPED ON OLD PIECE OF BELT TWISTED KNEE

54736YEE WAS SHOVELING ON BELT WHEN HE SLIPPED ON WET BOTTOM & FELL

61330OF ROOF OCC ON 425 TRACK AT 440 RETURN OVER CAST 20 . 35

A FALL OF ROOF OCCURRED ON SECTION 4520 AT SPAD 7 & 50 IT WAS IN THE BELT ENTRY APPROX. 1400 FEET FROM THE FACE SIZE IN 60X24X41/2 TOP WAS LAM SAND AND WAS BOLTED WITH 36 IN BOLTS.

EE WAS WAITING IN CROSSCUT FOR PIN CREW TO PIN FACE WHEN A PIECE OF DRAW ROCK FELL BETWEEN BOLTS AND STRUCK HIM.

A SMALL ROCK FELL FROM BOOM OF MINER & STRUCK EMPLOYEE ON TOE

WHILE EXTENDING BATTERY CHARGER ARM OF RAM CAR EMPLOYEE GOT HAND CAUGHT IN PINCH POINT.

EMPLOYEE WAS PULLING WATERHOSE WHEN HE GOT A CATCH IN HIS BACK WATER HOSE

EMPLOEE WAS THROWING BLOCKS ON TOP OF OVERCAST WHEN HE GOT A PAIN IN HIS BACK

EMPLOYEE WAS PINNING WHEN A SMALL PIECE OF SCALE FELL AND STRUCK HIM ON THE ARM.

EMPLOYEE WAS HOLDING VALVE ASSEMBLY FOR SECTION ELECTRICIAN WHEN HE ACCIDENTLY ACTIVATED STAB JACK. REAR OF MINER RAISED AND CAUGHT HIS HAND BETWEEN COVER AND ROOF.

EMPLOYEE WAS PULLING MINER CABLE WHEN HE GOT A PAIN IN HIS KNEE.

MINER OPERATOR WAS TRAMMING MINER WITH REMOTE AND PINNED HIMSELF AGAINST THE RIB BEHIND LINE CURTAIN.

EE SAID HIS RAM CAR WOULD NOT GO IN REVERSE SO HE KICKED TRAM PEDAL AND HURT RT FOOT.

EMPLOYEE WAS PINNING WHEN HE MASHED HIS HAND BETWEEN PINNER HEAD & CANOPY

BUILDING A STRIP BRATTICE,EMPL HIT TOP WITH HAMMER IT BOUNCED BACK AND HIT IN MOUTH.,

EMPL LIFTING ROCK FROM TRUCK,FELT A BURNING IN SIDE.

EMPLOYEE WAS WORKING ON FEEDER WHEN A PIECE OF DRAW ROCK FELL AND HIT HIM ON BACK AND FINGER.

A SMALL PIECE OF SCALE ROCK FELL FROM TOPAND STRUCK EMPLOYEE ON TOP OF FOOT.

EMPLOYEE WAS CROSSING BELT AND HE REACHED UP TO CUT THE BELT OFF AND HE CUT IT ON. IT THREW HIM OFF CUTTING HIS THUMB.

EMPLOYEE WAS DRILLING TOP WHEN A SMALL PIECE OF SCALE ROCK FELL AND CUT HIS FOREARM.

A FALL OFF ROOF OCCURRED IN THE 450 ENTRY AT THE FIRST OVERCAST SIZE WAS 60X24X4 1/2 AREA WAS BOLTED WITH 48 IN HIGH BOLTS.

FALL OF ROOF OCCURRED ON SEC 04225 AT SPAD 13+50 IN 2R AIR COURSE SIZE 70X20X4 1/2 TOP WAS SANDY SHALE.

EMPLOYEE WAS OPENING OIL DRUM WHEN PIECE OF METAL HIT HIM ON ARM.

SMALL PIECE OF SCALE ROCK FELL & STRUCK NOSE & FACE AS HE WAS HANGING WATER HOSE

FALL OF ROOF ON SECTION 04225 (I.D. 002) IN 1 LEFT HEADING AT SPAD 13+50, 600' OUTBY FACES. BLOCKING NEUTRAL TRAVELWAY AND WILL BE CLEANED UP. CALLED TO BIRMINGHAM OFFICE.

EE WAS TRANNING RAM CAR FROM THE FACE LACK TO THE FEEDER WHEN A PIECE OF DRAW ROCKS FELL FROM THE TOP STRIKING HIM.

EMPLOYEE WAS HELPING PULL BELT TOGETHER WHEN BRIDLE BROKE MASHING HIS FINGER BETWEEN BRIDLE & BELT ROLLERS

A FALL OF ROOF OCCURRED ON SEC 4225 IN THE 2R AIR COURSE SPAD 12+20 SIZE 50X24X5 THE FALL WAS 30 FT FROM FACE. AREA WAS BOLTED WITH 42IN BOLTS.

INJURED EMPLOYEE WAS PULLING MINER CABLE & GOT A PAIN IN HIS BACK

THE INJURED EMPLOYEE WAS GETTING OFF TRACK JEEP AND FELL HURTING HIS BACK.

SQUATTED TO GET OUT OF RAM CAR PAIN IN KNEE

INJURED EMPL STEPPED OFF MOTOR & TWISTED KNEE

A ROOF FALL OCCURRED IN SEC 450 SPAD 20+60 IN THE 3L AIR COURSE 2500 FT FROM FACE.SIZE 60X20X8.

A FALL OF ROOF OCCURRED ON SECTION 450 AT SPAD 20+60 IN 1L AND CROSSCUT FROM 1L TO 2L 2500 FT FROM FACE 150X20X8FT.

A FALL OF ROOF OCCURED ON SEC 450 AT SPAD 19+90 IN THE 2L AIR COURSE 50X20X8 2500 FEET FROM FACE.

A FALL OF ROOF OCCURRED ON SEC 450 AT SPAD 19+20 IN THE 3L AIR COURSE 3000FT FROM FACE SIZE 65X20X8.

A FALL OF ROOF OCCURRED ON SECT 450 AT SPAD 24+80 IN THE CROSSCUT BETWEEN HEADING AND 1L 2000FT FROM FACE.40X20X8.

EMPLOYEE WAS PULLING PUMP FROM SUMP AND MASHED HIS HAND PUMP AND BEAM.

THE EE WAS DRIVING TRACK JEEP AND HIT A ROCK ON THE RAIL CAUSING HIS TEETH TO JAR TOGETHER BREAKING TOOTH.

EMPLOYEE GOT CATCH IN BACK WHILE PLUGGING UP SCOOP BATTERIES.

EMPLOYEE WAS WORKING ON RAM CAR WHEN HE STRAINED HIS SHOULDER.

A FALL OF ROOF OCCURRED ON SEC 4225 N THE 1L TRAVELING AT SPAD 4+00 20X20X10 THE TOP WAS LAMINATED SAND.

EMPLOYEE WAS WORKING ON WATER LINE WHEN RIB ROLLED OVER ON FOOT.

EMPLOYEE WAS HANGING CURTAIN WHEN PIN MACHINE RAN OVER HER LEG.

A FALL OF ROOV OCCURRED ON SEC 4430 16 RM 30X 22X 5.

A FALL OF ROOF OCCURRED ON SEC 4430 IN THE FACE OF THE 17 RM 30X24X4 1/2 TOP WAS LIME SANDY SHALL.

PULLING TIE DOWN ROPE HURT BACK

WHILE PINNING THE PIN STEEL FELL & HIT BEAM SWUNG LEVER & CAUSED BOOM OF PINNER T O HIT KNEE

EMPLOYEE WAS PULLING A PIECE OF BELT WHEN HE GOT A PAIN IN HIS SHOULDER

EMPLOYEE WAS TEARING DOWN A PIECE OF CUTAIN WHEN HE GOT A PAIN IN HIS RIGHT SHOULDER AND NECK.

EMPLOYEE WAS CLEANING BELT WHEN HE GOT HAND CAUGHT BETWEEN BELT AND ROLLER.

A FALL OF ROOF OCCURRED ON SECTION 04225 IN THE CROSSCUT BETWEEN HEADING AND 1L AT SPAD 5+40 SIZE WAS. 25X20X6 AREA HAD BEEN BOLTED WHICH 48 IN B BOLT.

A FALL OF ROOF OCCURRED ON SEC 04225 IN THE HEADING OF SPAD 6+10. SIZE 20 X 20 X 8. AREA WAS BOLTED WITH 48' FOOT.

A FALL OF ROOF OCCURRED ON THE 4225 IN THE CROSSCUT BETWEEN THE HEADING AND 1R AT SPAD 4 +70 50'X20' X10' TOP WAS LAMINATED SAND.IT HAD BEEN BOLTED WITH 4 IN ROOF BOLTS.

A FALL OF ROOF OCCURRED ON SEC 4225 IN THE 2L AIR COURSE AT SPAD 3 +30 24'X24' X8'.TOP WAS LAM SANDS AND HAD BEEN BOLTED WITH 42" ROOF BOLTS.

A ROOF FALL OCCURRED ON SEC 4225 IN THE SHUIRTDAY HEADING AT SPAD 1+10. SIZE 20X50X10 AREA HAD BEEN BOLTED WITH 36 IN. BOLTS.

FALL OF ROOF OCCURRED ON SECTION 4225 IN BELT INBY SPAD 6/30.SIZE 20 X 24 X 9.AREA HAD BEEN BOLTED WITH 36" BOLTS.

A FALL OF ROOF OCCURRED ON SECTION 4225 IN THE 1L AIR CORSE AT SPAD 5 & 40 SIZE 40X15X8 AREA WAS LAMINATED SAND PREVIOUSLY PINNED WITH 36 INCH B HIM BOLTS.

EMPLOYEE WAS HOLDING SPLICE AND ANOTHER EMPLOYEE HIT HIS FINGER WITH A HAMMER.

DRAW ROCK FELL STRUCK ON NECK AND SHOULDERS

EMPL GOT FINGER CAUGHT BETWEEN 2 PIPES.

RECOVERING CURTAIN HE STEPPED ON NAIL

LOADING MATERIAL OF PINS WIRE BAND BROKE CUT HAND

INJ STEPPED OUT OF PORTAL BUS AND TURNED HIS KNEE.

A FALL OF ROOF OCCURRED ON 425 BELT HEADING JUST INBY 440 PANEL AT SPAD 51+70 SIZE ROCKS 15 X 24 X 5 AREA HAD BEEN BOLTED WITH 36 IN BOLTS.

WHILE SCALING TOP A SMALL PIECE OF SCALE RACK FELL AND STRUCK HIM ON THE HAND.

EMPL WAS HOLDING PIPES TOGETHER & GOT FINGER MASHED.

EMPL SLIPPED & FELL ON WET BOTTOM HIT LEG ON TRACK RAIL.

A FALL OF ROOF OCCURRED ON SECTION 4215 B AT SPAD 12 +40 IN THE 1 R ENTRY 150 FEET OUTBY FACE.30X28X5 HAD BEEN BOLTED WITH 36 AND 42" BOLTS.

CAUGHT FINGER BETWEEN ELEVATOR DOORS AT TOP OF ELEVATOR.

FALL OF ROOF OCCURRED ON SEC 450 IN HEADING LAST BREAK AT SPAD 12=40 24X20X6 AREA HAD BEEN BOLTED WITH 42" RESIN PIN.

CAUGHT FINGER BETWEEN SCOOP FRAME AND SAFETY BUMPER

FALL OF ROOF OCCURRED ON SECTION 450 AT SPAD 14+00 IN SLANT BETWEEN 1 R 20X20X6 HAD BEEN BOLTED WITH 48 IN BHA BOLT PINS.

INJURED EMPL WAS OPERATING SCOOP WHEN HE HIT LUMP & JARRED BACK.

THE INJURED EMPLOYEE WAS CUT TING BELT CABLE WHEN IT FLEW UP & HIT HIM ON ARM

THE INJURED EMPLOYEE WAS PINNING IN HIGH HOLE WHEN A SMALL ROCK FELL AND HIT HIM ON THE HAND.

WHILE RIDING IN RAM CAR EMPLOYEE WAS STRUCK ON SHOULDER BY PIECE OF DRAW ROCK.

EMPLOYEE WAS RIDING IN RAM CAR WHEN IT HIT A BUMP & THREW HER UP & BOUNCED HER ON SEAT CAUSING INJURY

FALL OF ROOF OCCURRED ON SEC 450,#6 ROOM SPAD 6/30. 130 X 20 X 8 AREA HAD BEEN BOLTED WITH 48" ?B.... BOLT HI-TECH.

A FALL OF ROOF OCCURRED ON SECT 450 PARRALLEL RM AT SPAD 105 AND 70 IN INTAKE. SIZE 35X20X4 HAD BEEN BOLTED WITH 48 INCH BOLTS.

A FALL OF ROOF OCCURRED ON SECT 425 IN THE RETURN AT SPAD 13+30 SIZE WAS 90X20X5 AREA HAD BEEN BOLTED WITH 36 IN BOLTS.

A FALL OF ROOF OCCURRED INT HE INTAKE ON SECTION 4215 AT SPAD 7+65 SIZE 30X20X5 AREA AND BEEN BOLTED WITH 36 IN BOLTS.

A FALL OF ROOF OCCURRED ON SECTION 4215 ON BELT LIN AT SPAD 7+00. SIZE 85X20X8AREA HAD BEEN BOLTED WITH 48 IN REHIND BOLT HI-TECH.

FALL OF ROOF OCCURED ON SEC 4215 IN 1L AIR COURSE AT SPAD 13+70 SIZE 40X20X8 AREA PINNED WITH 42" RESEN BOLTS.

THE INJURED EMPLOYEE WAS SITTING AGAINST RIB WHEN A PIECE OF ROCK FELL FROM TOP AND STRUCK HIM ON THE BACK.

A FALL OF ROOF OCCURED ON SEC 4050 IN THE #5 REOOM IN FACE CROSSCUT SPAD 4+80 40X20X5 PREVIOUSLY USING 36IN BOLTS

A FALL OF ROOF OCCURED ON SECT 4050 IN FACE XCUT SPAD 5140 600X30X4 BOLTED WITH 36IN BOLTS THIS WAS IN #6 ROOM

THE INJURED EMPLOYEE WAS LIFTING DRUM OF OIL TO PUT IN RAM CAR WHEN HE GOT A CATCH IN HIS BACK.

EMPLOYEE WAA TROUBLE SHOOTING COAL VIBRATOR WHEN HE GOT HIS FINGER CAUGHT BETWEEN VIBRATOR AND FRAME.

THE INJURED EMPLOYEE WAS LIFTING ROLL OF CURTAIN WHEN HE GOT A CATCH IN HIS BACK.

THE INJURED EMPLOYEE WAS USING SLEDGE HAMMER WHEN HE GOT A PAIN IN HIS BACK.

THE INJURED EE WAS LIFTING CRIB BLOCKS AND GOT A PAIN IN HIS BACK.

ROOF FALL OCC IN 1 L HDG.FACE OF SECT 04205 JAST AS DAY SHIFT PREPARED TO LEAVE SECTION AT END OF SHIFT 20'W 18'L 4 1/2' FT HT MAX WAS NOT BOLTER NO EQUIP NO INJ

A RALL OF ROOF OCCURRED ON SECTION 4205 IN THE 1 LEFT AIR COURSE AT SPAD 10 + 20. SIZE 150' X 20' X 8'. AREA HAD BEEN BOLTED WITH 36" AND 48" BOLTS TOP WAS LAM. SANDY SHALE.

WHILE EMPLOYEE WAS PINNING A SMALL PIECE OF DRAW ROCK FELL FROM THE TOP AND STRUCK HIM ON THE LEFT FOOT.

EMPL ON KNEES OPERATING MINER.THEN WENT TO SITTING POSITION ,HIS KNEE POPPED.

THE INJURED EMPLOYEE WAS GOING FROM HIGH COAL TO LOW COAL WHEN HE STEPPED IN A HOLE AND TWISTED HIS KNEE.

INJURED EMPL WAS LIFTING SEAL BLOCKS WHEN HE GOT BURNING IN GROIN.

INJURED EMPL WAS OPERATING SCOOP WHEN HE RAN OUR ROCK IN ROADWAY HURTING BACK.

A FALL OF ROOF OCCURRED ON SECTION 04205 IN THE #4 ROOM & 15+40 IN THE FIVE AREA SIZEW WAS 25X20X8 IT FELL ON THE PINNER

A FALL OF ROOF OCCURRED ON SECT 04205 IN FACE AREA DISCOVERED AT 600PM SUN.FEB 4 1990 APPROX 25FTLX28FTWD&6FTH PARTLY ON CONT MINER INVESTIGATION BY MSHA INSPECTOR I NAME & MINER OUT COAL ON N EXT PRODUCTION SHIFT MON AM 2-5-90 IMMEDIATE ROOF LAMINATED SANDY SHALE

PRIZE BAR SLIPPED UNDER PRESSURE,WHILE PUTTING DIGGING ARM ON MINER GATHERING HEAD.

INJURED EMPL WAS LIFTING CRIB BLOCKS WHEN HE GOT CATCH IN BACK.

THE INJURED EMPLOYEE WAS HOLDING WRENCH ON NUT ON MOTOR WHEN WRENCH SLIPPED HITTING HIM IN NOSE.

THE INJURED EMPLOYEE WAS USING ROOF BOLT TO DISLODGE BELT FROM SHIRT RUBBER WHEN IT SLIPPED AND CUT HIS HAND.

THE INJURED EE GOT OFF THE MOTOR TO THROW THE TRACK SWITCH AND TWISTED HIS KNEE.

THE INJURED EE WAS CARRYING A BUCKET OF BEROSENE IN TOP OF ELEVATOR WHEN HE FELL AND BROKE HIS HAND.

THE INJURED EMPLOYEE WAS CARRYING A DRUM OF OIL WHEN HE STEPPED IN A DITCH HURTING HIS BACK.

MINER ON SECTION 4420 WAS CUTTING PLACE THROUGH TO OLD SET OF ROOMS WHEN HE CUT THROUGH WATER RUSHED IN & FLOODED SECTION SPPROX 2' DEEP. NO INJUREIS.

RF OCC ON SECTION 43D IN BELT RRACK HEADING AT SPAD 41+20 TO 41+90 SZ OF FALL 70X24X10 BOLTED WITH 48"BOLTS TOP LAM SANDY SHALE

A FALL OF ROOF OCCURRED ON SECTION 4315 IN THE 2R AIRCOURSE AT SPAD 3+40 IN THE INTAKE ESCAPEWAY SIZE 20X20X4 HAD BEEN BOLTED WITH 36 INCH BHN BOLTS.

A FIRE OCCURRED ON THE CLEAN COAL BELT FROM THE TUNNEL AREA TO THE TOP FLOOR OF THE LOADOUT BUILDING. THE BELT WAS TOTALLY DESTRAYED WITH DAMAGE TO THE HEND HOUSE.

THE INJURED EMPLOYEE WAS MOVING BELT TAIL PIECE WHEN SPOOL OF WIRE ROPE FELL ON FOOT.

THE INJURED EMPLOYEE WAS KNEELING NEAR COAL RIB WHEN IT "POPPED" WITH FRAGMENT HITTING HIS EYE.

A FALL OF ROOF OCCURRED ON SECTION 4215 INT EH 1L AIR COURSE AT SPAD 5+60, 30X24X4 TOP STRATA LAM SANDY SHALE AREA WAS BOLTED WITH 48IN. BOLT HIGH TECH.

THE INJURED EMPLOYEE WAS LIFTING A BOX OF PARTS WHEN HE GOT A CATCH IN HIS BACK.

FALL OF ROOF OCCURRED SECTION 4420 BELTLINE AT SPAD 2/20 SIZE 40 X 24 X 5.TOP WAS LAM SAND AND HAD BEEN BOLTED WITH 36" BOLTS.

FALL OF ROOF OCCURRED ON SECTION 4215 AT SPAD #5+60 IN LOX BETWEEN HEADING & 2R SUZE 70X20X6 TOP WAS LAM SANDY SHALE.

THE INJURED EMPLOYEE WAS ROOF BOLTING WHEN A SMALL PIECE OD SCALE FELL FROM TOP AND HIT HIS LEFT ARM.

A FALL OF ROOF AT INTERSECTION OF 440 HDG AND 4420 SECTION BETWEEN 2 & 3 RT OF 440 HOG & IS IN 1 RT OF 4420 40'L 20 TO 22'W 48" T LAMINATED SHALE ROOF WITH STEAKS OF SAND AREA SUPPORTED INITIA LLY WITH 36" BIHAM BOLT

WHILE MOVING SCOOP CHANGE UP A SMALL PIECE OF DRAW ROCK FELL FROM THE TOP AND STRUCK HIM ON THE RT HAND.

INJ SHOVELING COAL FROM RAM CAR TRAILER WHEN HE SUFFERED LUMBAR STRAIN.DIDNT SEEK TREATMENT UNTIL 9-4-89.

A PIECE OF RIB FELL & STRUCK THE EMPLOYEE ON THE FOOT WHILE HE WAS OPERATING THE MINER

THE INJURED EMPLOYEE WAS OPERATING ROOF BOLTER AND MASHED INDEX FINGER WITH THE CANOPY OF THE ROOF DRILL.

A FALL OF ROOF (UNKNOWN EXACT TIMES) ON SECTION #430 HDG. IN 2 RT HDG.(INTR) @SPAD NO 45+85 APPROXIMATELY 50' X20'X5' THICK.LAM SANDY SHALE IMMEDIATE ROOF.SUPPORTED BY 48" JENN MAR COMB RESIN REBOLT.

FOUR HAULAGE CARS; BECAME UNCOUPLED FROM THE BRAKE CAR WHEN A SAFETY CHAIN BROKE THEY TRAVELED APPROX 900FT BEFORE THEY WRECKED AT THE BOTTOM OF SLOPE

A FALL OF ROOF AT SPAD NO 4+20 RMS TO RT OFF 3 RT AIR COURSE MID RM HDG SET OF 5 RUS AT FACE EXTENDING TO OLD CLEANED UP FALL IN 3 RT HDG 85'L 20'W 6'T LAM SANDY SHALE ABOVE ANCHORAGE OF 48" B HAM HIGH TECH BOLT

A FALL OF ROOF OCCURRED IN BELT & TRACK HEADING OF 425 PANEL AT SPAD 43+50 21X70X20 LAM SANDY SHALE HAD BEEN BOLTED WITH 48IN FULLY GROUTED RESIN BOLTS

A FALL OF ROOOF OCCURRED ON SECT 450 IN 3 R AIR COURSE AT SPAD 4+20 SIZE 30X22X4 STRATA WAS LAM SHALE AND HAD BEEN BOLTED WITH 48 IN BOLTS.

THE INJURED EMPLOYEE STEPPED OFF OF PORTAL BUS AND TURNED HIS ANKLE.

A FALL OF ROOF OCCURRED IN 430 BELT HEADING AT 3RD OVERCAST AT SPAD 5+40 SIZE WAS 26X2 4X3 TOP WAS LOW SENDING SHALE BOLTED WITH 36IN XXXBOLTS

A FALL OF ROOF OCCURRED ON SECTION 450 BELT HEADING AT APD 2+80-3+50 SIZE WAS 70X24X4-10 FEET THICK. LAM SANDY SHALE AND HAD BEEN LISTED WITH B. BOLT 48IN BOLTS.

INJ HURT HIS BACK SNATCHING LOOSE CURTAIN OFF BOOM OF MINER.

A SMALL PIECE OF SCALE ROCK FELL FROM BETWEEN BOLTS AND STRUCK HIM ON THE LEFT LEG.

THE INJURED EMPLOYEE WAS CHECKING PLUG WITH METER WHEN METER BLEW UP AND BURNED HIS HAND.

INJURED EMPLOYEE WAS WORKING ON MINER WHEN HE CUT HIS HAND ON PANEL COVER LID

THE INJURED EMPLOYEE WAS WORKING ON PUMP AT CREEK REAR WASHER WHEN HE SLIPPED AND TWISTED HIS KNEE.

THE INJURED EMPLOYEE WAS WORKING BESIDE RAM CAR AND REACHED HIS HAND ACROSS SHARP EDGE OF PANEL COVER ON RAM CAR.

A FALL OFF ROOF OCCURRED ON SECT. 430 (I.D. 018) IN 3 LEFT HDG. APPX. 100 FT. OUTBY FACE TO 170 FT. OUTBY. FALL IS APPX. 70 FT. X 24 FT. X 5 FT. HIGH. TOP WAS LAMINATED SAND WITH SANDY SHALE. AREA BOLTED WITH 48" RESIN BOLTS.

A FALL OF ROOF OCCURRED ON SECT 4065 IN THE 3R AIR COURSE AT SPAD 3+60 TO 4+20 SIZE WAS 95 X 24 X 7 120 FEET FROM THE FACE

A FALL OF ROOF OCCURRED ON SECTION 4315 IN THE 1R AIRCOURSE AT SPAD # 4410 SIZE WAS 25X20X6. TOP WAS LAW SANDY SHALE TOP WAS PREVIOUSLY PINNED WITH BOLT 42 INCHES HIGH TECH BOLTS.

INJURED EMPLOYEE WAS L0ADING MATERIAL ON YARD WITH FORKLIFT HE GOT OFF TO ADJUST ROLL OF CURTAIN & FORK LIFT ROLLED FORWARD TRAPPING HIM BETWEEN BUMPER OF FORKLIFT & MINE CAR

A FALL OF ROOF OCCURRED ON SECTION 425 IN THE FACE CROSSCUT BETWEEN 2R AND 3R AT SPAD 02+20 SIZE WAS 35 X 20 X 3 1/2 TOP WAS LIME SANDY SHALE

A FALL OF ROOF OCCURRED IN THE 1R AIR COURSE OF SECT 425 AT SPAD #77+70 SIZE 24 X 20 X 7 TOP WAS LIME SANDY SHALE BOLT WITH 48 IN JEN MAR BOLTS

EMPLOYEE WAS LIFTING A BELT ROLLER AND GOT A PAIN IN HIS BACK.