Employee was climbing down the ladder on the front end loader and twisted EE's right knee. Employee did not miss any work and was not placed on restrictive duty. Employee's first day of missed work was May 12, 2025.
Employee was working on screen #4 repairing a drive motor when a piece of consolidated limestone dust fell down onto employee from conveyor #33 located above screen #4. Conveyor #33 was not running at the time of accident. The piece of consolidated limestone dust struck employee in the back.
Employee was working on conveyor 7. While removing the chain from the conveyor drive system employee's left hand thumb & forefinger were pinched and lacerated by the chain.
Employee was straightening a rear access step on a Cat 980G front end loader. The employee was using a steel bar to straighten the step. The bar slipped free causing employee to lose balance and place all his weight and momentum on lower right leg.
EE was painting on processing plant and felt his knee pop when raising from a squatting position. Cont's. to work without restriction on 4/9 & 4/10. Became reportable on 4/11/13 when EE went to doctor due to discomfort. Doctor requested that EE not work for 5 days.
EE slipped and fell while performing maintenance work on 2/14/2012. This became reportable on 4/3/2012 when he went to doctor for the first time and doctor requested physical/occupational therapy after work hours with no work restrictions.
While assembling a cone crusher, the bowl adjusting cylinder was working back and forth. While trying to hold the cylinder in place the injured employee pinched his finger causing a cut that required stitches.
EE was working on a conveyor belt in a kneeling position, when he stood up to re-position himself, he felt a pop and muscle strain in his left knee.
EE strained his back while attempting to pick up a 20 lb object. He has not missed any work but on 3/30/11 he saw a doctor for continued discomfort from 9/27/2010 incident making it a reportable injury.
EE strained a muscle in his left thumb while lifting a pail of nuts and bolts. This became a reportable injury on 3/23/10 when his doctor requested physical/occ. therapy and temporary restricted use of his left thumb.
EE was fusing pipe together, while in the process, he injuried his knee. **This was not diagnosed until 7/23/08.
While dismounting from the trackhoe, he strained his lower abdomen.
Employee was cutting a piece of steel that two other workers were supporting. When he broke through the steel it slid, getting away from the other two workers. The steel plate slid down hitting employee's foot, bending it downward, putting strain in his back.
While pushing off on a stockpile with a front end loader, one wheel of the loader went into a dip in the grade causing a jolt straining his lower back.
Employee was installing steel wear plate in the crushing mill. The load shifted and he twisted trying to control the load, injuring his lower back and leg muscle.
EE WAS HELPING REPLACE A SHAFT IN THE CRUSHER. AS THE SHAFT WAS SWUNG INTO PLACE HE GOT HIS HAND PINCHED BETWEEN THE SHAFT AND HAND RAIL.
REPETITIVE MOTION UP AND DOWN LADDER OF HAUL TRUCK CAUSED STRAIN ON KNEE. (PENDING WORKMAN'S COMP INVESTIGATION)
INJURED WAS REPLACING ROLLER FRAME ON PLANT SURGE BELT. INJURED HIS BACK AND LEFT LEG.
OPERATOR WAS HAVING A LOAD OF DIRT TO WASTE DUMPSITE AS HE COMPLETED DUMPING IS LOAD THE GROUND AT THE REAR OF THE TRUCK STRATED TO GIVE WAY.THETRUCK BEGAN TO SUDE BACKWARD AT THAT POINT THE OPERATOR JUMPED FROM THE CAB TO THE GROUND CAUSING INJURY TO HIS LEFT FOOT AND LOWER BACK. TRUCKSLID APPROX. 30 FT AND WAS STOPPED BY A DIRT BANK AND LOWER BACK. TRUCK SLID APPROX. 30 FT. AND
GREASING EQUIPMENT WHEN HE TRIGGER HIGH PRESSURE HOSE FROM CLOSE RANGE STRIKING HIMSELF IN THE EYE WITH A STREAM OF GREASE.
OPERATOR STOPPED ON HAUL RAMP TO REMOVE LARGE ROCKS FROM HIS PATH. HE KICKED A ROCK OFF THE RAMPAND IN DOING SO STRAINED HIS KNEE
EMPLOYEE WAS REPLACING A WEAR PLATE AT THE CRUSHING PLANT. HE LIFTED A PIECE OF STEEL & INJURED HIS LOWER BACK.
EE WAS STEPPING OFF LOADER, SLIPPED AND FELL, HITTING HIS KNEE ON LOADER STEP.
EE WAS CHANGING SCREENS ON A SCREEN DECK. HE PULLED A SCREEN, SLIPPED AND INJURED HIS BACK.
EE RECEIVED FLASH BURN FROM C0-WORKER WELDING INTHE SAME AREA.
EE WAS IN THE PROCESS OF WASHING UNIT #330 WITH A POWER STEAM JENNY WHEN HE SLIPPED. WHILE TRYING TO CATCH HIMSELF THE LINE OF HOT WATER PRESSURE CAME ACROSS HIS RIGHT FOOT.
EE WAS LIFTING I BEAM OUT OF ROCK HOPPER. HE LOST HIS FOOTING FELL AND BUMPED HIS KNEE ON A ROCK.