Antire Quarry (CS-72) Metal/Non-Metal

Employee alleges they were changing a drill bit and the drill fell from the hammer and pinned the index and ring fingers under the drill bit causing injuries to their right hand. Employee also received stitches.

Employee alleges employee was standing on a platform trying to unhook a chain and fell backwards off of the crane landing on the ground.

Employee was doing maintenance at the plant, removing a section of catwalk. While doing so, the catwalk fell hitting EE's wrist pushing it into the hood of the scalping screen causing laceration on the outside of EE's rt wrist.

Employee was belt splicing when EE reached for the skiver tool by twisting backward to the right, reaching with EE's right hand/arm. Once EE had hold of tool EE realized it was hung on a piece of belting, EE started pulling and jerking to free up the tool when EE heard pop from shoulder and felt pain.

Employee was lifting a full argon gas cylinder for the welder. Felt pain in lower back. Returned 1/08/21 - didn't report until 1/11/2021 - at that time we sent EE to the Doctor.

Employee was working on a conveyor scraper. While tapping on scraper bracket with hammer, struck right forefinger knuckle against bracket causing abrasion. EE did not initially report injury, thought it to be minor, on Sunday 9/20 it was infected and sought treatment @ urgent care.

Employee was working on the shop floor underneath the Komatsu 900 pit loader. When coming up from under machine EE hit head on the edge of the hydraulic tank causing a laceration on the top of EE's head, requiring stitches.

Employee was using a utility knife to cut a piece of conveyor belting. In the process the blade pulled from the belting, the knife struck EE's right leg which caused a laceration that required sutures.

employee was walking on crusher catwalk after crusher went down, stepped on rock and rolled ankle causing ligament strain of right ankle.

Employee arrived for the shift, while walking across the wet limestone parking lot EE slipped and fell onto knees, causing contusion on L knee. At time of this injury on 9/3/19, EE thought was okay. On 10/24/19 EE reported knee still bothering EE. Was sent to Dr for 1st visit. On 11/4/19 EE had follow-up & Dr put EE on restrictions.

Employee was at the crusher spraying inside of chute with 115 psi. The hose tip was just inside the chute door. Something broke loose above and it fell down hitting tip of the hose which caused employee's arm to go downward causing bone fractures in left arm.

Employee was going up steps of skid steer to pull the keys from the ingnition for the day. After retreiving the key, EE pivoted on EE's foot causing the boot tread to get caught in the step of the machine. Employee was thrown off balance and fell approx 2' to ground on right shoulder.

Employee was using pick axe to clear chute build up. The pick axe hit hard build up and slid off going deeper into chute, causing employee's finger to strike the chute hinge causing laceration.

Employee was rolling air hose onto reel by hand when a twist at the end of the hose came undone and hit him in the mouth, causing his tooth next to the front tooth to break off.

EMPLOYEE WAS ON DOZER PLATFORM AND DROPPED HIS PENCIL, BENT OVER TO PICK IT UP AND BUMPED HIS HEAD ON THE MACHINE WHICH CAUSED HIM TO LOSE HIS BALANCE, LOST HIS GRIP AND SLIPPED DOWN ONTO HIS PICKUP TRUCK HOOD WHICH WAS PARKED NEXT TO HIS MACHINE, THEN SLIPPED DOWN TO THE GROUND.

employee was walking up on hill # 4 (with safety glasses on) to work on hydraulic drill, when he felt scratchiness, burning and watering of the left eye. foreign object in eye.

EMPLOYEE WAS HOLDING IN POSITION A PIECE OF WATER PIPE ON ONE END AND THE CRANE WAS HOLDING THE OTHER SO THEY COULD BE WELDED TOGETHER. THE END THE EMPLOYEE WAS HOLDING DROPPED DOWN 6" TO THE GROUND CAUSING THE EMPLOYEE'S PINKY FINGER TO GET BETWEEN THE PIPE AND THE GROUND, CAUSING LACERATION.

Employee was using wheel grinder on a piece of plate steel. Foreign object in right eye.

Employee was using a 6' pry bar on the hood at the shaker. The pry bar slipped and caused him to lunge forward on the catwalk approx 10' falling against the lower hand rail.

Employee was removing bent conveyor for repairs. While using a 12' x 12' timber to block the conveyor, the timber was pushed to far on one end causing his end to drop down onto angle iron which caught his pinky on right hand, which partially tore the fingernail from the nailbed.

Employee was getting off his excavator when he noticed there was mud on the step. To avoid slipping from the step he jumped from the track approx 3' landing on his left heel, which in turn caused pain in his back and leg.

Employee was working on snow removal with his highlift when he struck a piece of frozen ice and it jarred him in his machine causing pain in his lower back. EMPLOYEE RETURNED TO WORK ON 1/28 & 1/29/09....FIRST DAY MISSED 1/30/09

EMPLOYEE WAS PUTTING A CONVEYOR BELT ON WITH A ROPE ATTACHED TO A PULLEY THAT WAS THEN ATTACHED TO A TRUCK TO PULL. THE PULLEY BROKE AND THE ROPE HIT THE EMPLOYEE IN THE FOOT/ANKLE (R).

EMPLOYEE WAS HAMMERING ON WOOD BLOCK TO REMOVE SHAFT FROM THE SHAKER. MEANWHILE, THE SHAFT BREAKS LOOSE FALLING ONTO EMPLOYEE'S (L) LEG PINNING IT BETWEEN THE SHAFT AND THE DIVERTER PLATE.

Employee was using his left hand to hold the "raise bed" switch on his loaded haul truck. His hand slipped from the switch causing his bed to free fall approx 1-2' causing the employee's body to jar.

EMPLOYEE WAS AT THE PLANT INSTALLING DUST SHIELD OVER THE CONVEYOR WHEN HE FELT A SHARP PAIN IN HIS LEFT CALF. POSSIBLE REPETITIVE MOTION FOR THE PAST 2 DAYS APPROX 5 HRS/DAY STANDING ON THE BALL OF HIS FOOT.

For the past 6 days for 2-3 hrs per day, this employee has been lying on his back at the crusher cleaning tar paper off the screens (from crushing asphalt) with his arms in the air. The repetive motion of holding arms up caused a golf ball size lump to pop up on his shoulder at the joint of the arm.

Employee was operating a skidsteer cleaning up at the crushing plant. When he got out of the machine he felt a pain in his lower left back. (Not reported until 1/07/08).

EMPLOYEE WAS IN A MAN LIFT TURNING ANGLE BRACKETS IN THE UPRIGHT POSITION TO SET THE CONVEYOR FRAME ONTO THE BRACKETS. THE OPERATOR HOLDING THE END OF FRAME WITH FORKLIFT MOVED AND IT CAUSED THE CONVEYOR FRAME TO MOVE AND LET CONVEYOR COME DOWN , RESTING UPON EMPLOYEE'S LEFT THUMB.

This over the road driver got out of his truck @ stockpile (restricted area) while waiting to be loaded to air up his low tire. On the ground he reaches into his truck to turn on a valve to put compressed air to his air hose. He then accidentally released his parking brake which allowed the truck to roll back and his leg ended up under the front wheel of his truck.

Employee was climbing off a D8R Cat Dozer and lost his footing. Employee's right ankle hit the dozers blade arm and a step welded to the blade arm , causing bruising and swelling.

Employee was on the haul road with his haul truck. There was a large rock in the roadway. Employee proceeded to roll the rock off the road and in the process hurt his shoulder. *****1st day of treatment = 9/26/06******

Employee was making a J bolt out of a concrete anchor. Instead of using a hammer he used a 2" steel pin to strike the bolt. While hammering he slipped causing him to slide his little finger into the bolt causing laceration.

EE WAS CHANGING SCREEN CLOTH AT THE CRUSHER, STEPPED ON THE DISCHARGE LIP CAUSING EE TO SLIP AND LOSE FOOTING. EE SLIPPED DOWN THE DISCHARGE SHOOT APPROX 6' LANDING ON THE CONVEYOR BELT.

Employee was using power saw to cut a piece of plywood when he felt something in his left eye. (EE was wearing safety glasses).

EE WAS REPLACING THE BEARING ON THE BEND ROLLER. THE CABLE HOLDING THE ROLLER SLIPPED CAUSING IT TO HIT HIS FINGER CAUSING A LACERATION.

EE WAS CLIMBING THE LADDER TO GET IN HIS TRUCK WHEN HIS HANDS SLIPPED FROM THE HAND RAILS, CAUSING HIM TO FALL TO THE GROUND.

EMPLOYEE WAS USING CUTTING TORCH TO CUT THE LEGS OFF A CONVEYOR. THE LEG FELL DOWN HITTING EMPLOYEE ON THE RIGHT SIDE OF THE FACE AND THE EAR. THE RIGHT EAR RECEIVED A LACERATION AS WELL AS A BURN FROM THE HOT METAL.

EE WAS STANDING ON A LADDER, UP APPROX. 6', WHEN HE OVER EXTENDED, CAUSING THE LADDER TO FALL TO THE SIDE. EE HIT HIS SHIN.

EMPLOYEE HAD JUST MOVED TO A NEW WORK STATION & KEPT HITTING HER ELBOW ON THE COUNTER. NERVE IMPINGEMENT IN LEFT ELBOW CAUSING THE TIPS OF HER SMALL/RING FINGERS TO BECOME NUMB.

EE WAS STEPPING OVER WELDING LEADS & TRIPPED. HE WENT HEAD FIRST INTO THE CATWALK HANDRAIL.

EE WAS SPOT WELDING A PIECE OF PLATE STEEL. HE SLID OVER ROLLING HIS LEG OVER THE PLASMA CUTTER, CAUSING IT TO TURN ON AND BURN HIS LEG.

EE WAS CLIMBING THE LADDER TO HIS HAUL TRUCK WHEN HIS FOOT SLIPPED CAUSING HIM TO SLIP DOWN LANDING ON THE NEXT LADDER RUNG.

EMPLOYEE WAS USING AIR CHISEL TO REMOVE HAMMERS FROM CRUSHER. A PIECE OF THE BIT BROKE OFF AND LODGED IN HIS CHEST.

EE WAS LIFTING A ROCK TO UNJAM CRUSHER, WHEN THE ROCK ROLLED INTO ANOTHER ROCK, PINNING HIS FINGER, CAUSING LACERATION.

EMPLOYEE WAS LIFTING A SAW HORSE WHEN HE FELT PAIN IN HIS RIGHT ARM, SHOULDER AND NECK.

EE WAS USING CUTTING TORCH ON A PIECE OF PLATE STEEL. AS HE WAS BACKING AWAY FROM HIS PROJECT HE TRIPPED OVER A ROCK CAUSING HIM TO FALL & BREAK ANKLE

EMPLOYEE SUSPECTS HE HAD OIL ON THE BOTTOM OF HIS SHOES WHEN HIS FOOT SLIPPED FROM THE CATWALK OF HIS HAUL TRUCK AS HE WAS OPENING THE CAB DOOR.HE FELL APPROX. 8 FEET TO THE GROUND.

EE IS HAVING NUMBNESS IN BOTH HANDS AND UP TO HIS ELBOWS. POSSIBLE CARPAL TUNNEL DUE TO REPETITIVE MOTION OF A MACHINE OPERATOR.

EE WAS WALKING DOWN HITTSIDE LAYING OUT SHOT FOR BLASTING. HE SLIPPED, TRIED TO CATCH HIMSELF FROM FALLING WHEN HE FELT A TWINGE OF PAIN IN HIS NECK.

EE WAS PULLING DRILLING HOSES FROM DRILLED HOLES WHEN HE FELT DISCOMFORT IN HIS LOWER BACK.

AN ELECTRICAL SHORT IN THE CABL OF A D8L DOZER PARKED INSIDE THE MAINTENANCE BUILDING, CAUSING THE BUILDINGS TO BURN TO THE GROUND, DESTROYING ALL CONTENTS WITHIN.

EE WAS STEPPING OUT OF THE BOBCAT WHEN HE TWISTED HIS ANKLE.

EE CLAIMS THAT FROM YEARS OF EXCESSIVE NOISE FROM THE ROCK DRILL THAT HE IS LOSING HIS HEARING.

EE STATE THAT FROM REPEADTELDY RUNNING THIS MACHINE THIS IS CAUSING PAIN IN HIS THUMB AND IN HIS WRIST.

EE LOST TIME AGAIN 1-5-98, RETURNED 3-9-98.

EE CUT OLD PLATE FROM INSIDE STORAGE BIN TO REPLACE WITH A NEW PLATE. HE WAS USING A GRINDING WHEEL TO REMOVE EXCESS METAL FROM SIDE OF BIN WHEN A PIECE OF FOREIGN MATERIAL LODGED IN HIS LEFT EYE. EE WAS WEARING SAFETY GLASSES NOT GOGGLES.

EMPLOYEE WAS CUTTING OLD LINE ROUT OF ROCK BOX AT SCREENING PLANT WITH A CUTTING TORHC. HOT PIECE OF SLAG DROPPED DOWN INTO HIS LEFT EAR CANAL.

EE IS SUFFERING FROM NUMBNESS IN BOTH HANDS. HE FEELS THAT THE REPETIVENESS OF HIS JOB OPERATING FRONTEND LOADERS, DOZERS, ETC. IS CAUSING THIS PROBLEM. EE WAS DIAGNOSED 2/97. FIRST DAY MISSED WORK DUE TO SURGERY WAS ON 5-1-97.

EE WAS HELPING TO INSTALL A BED CYCLINDER ON A CATERPILLAR HAUL TRUCK WHEN THE CYCLINDER HE WAS HOLDING UP SLIPPED FROM POSITION, CAUSING IT TO HIT HIS THUMB ON HIS LEFT HAND.

EMPLOYEE WAS CLIMBING UP WOODEN SHELVES TO GET SOME LUMBER DOWN THAT WAS STACKED UP THERE. ON HIS WAY DOWN HE GOT A VERY LARGE SPLINTER OF WOOD IN HIS RIGHT INDEX FINGER.

EMPLOYEE WAS ATTEMPTING TO GET OFF HIS HAUL TRUCK WHEN HE MISSED THE HAND RAIL, FALLING TO THE GROUND.

EE WAS WALKING ACROSS AN ICY SPOT ON THE CATWALK AT THE CRUSHING PLANT. HE TRIED TO PREVENT HIMSELF FROM FALLING AND HE TWISTED HIS KNEE.

EE WAS PUTTING A STEEL PLATE IN THE ROCK BOX OF THE CRUSHER WHEN HE FELT A PAIN IN HIS BACK AND SHOULDER.

EMPLOYEE WAS STANDING ON THE FENDER OF TE FRONTEND LOADER TAKING THE SCREWS OTU TO PULL THE ENGINE. HE LOST HIS FOOTING, HE THEN GRABBED THE HANDRAIL TO CATCH HIMSELF.

EMPLOYEE HAD JUST STARTED FOR ONE DAY WHEN HE WAS GOING UP THE LADDER ON HIS FRONT END LOADER.HE MISSED ONE OF THE STEPS,WHEN HE DID HE GRABBED THE RAIL WITH HIS RIGHT HAND CAUSING HIM TO SWIN G INWARD TOWARD HIS RIGHT HAND SPRAINING HIS WRIST.

EMPLOYEE WAS SERVICING THE CRUSHING PLANT BY CHECKING OIL ON TEH SCREENS WHEN HE TRIPPEDON TEH STEPS OF THE WALK AN DFELL ON HIS RIGHT ARM.

EMPLOYEE WAS GREASING PULLEY ONT EH STACKE RBELT WHEN E TRIPPED OVER THE GAURD WHICH CAUSED HIM TO HIT HIS SHOULDER AS HE FELL APPROX 5'.

EMPLOYEE WAS GRINDING ON A SLIDE FOR A TAILPULLEY WITH A HAND HELD GRINDER WHEN THE GRINDER JUMPED BACK HITTING THE EMPLOYEE IN THE FOREARM

EE WAS LOADING A TRUCK AT THE LIME PILE. HE FILLED HIS BUCKET AND WAS IN THE LIFTING MTOTION WITH HIS BUCKET WHEN A LARGE PIECE OF THE STOCKPILE FELL FROM THE TOP HITTING ON TOP OF HIS LOADER BUCKET. WHEN THAT HAPPENED IT CAUSE THE FRONT OFHIS MACHINE TO GO DOWN AND THE BACK TO GO UP. THAT CAUSED THE EE TO BE JARRED AROUND INSIDE HIS MACHINE.

EE WAS USING A METAL ROD TO GET MUD OFF THE ROLLERS OF THE CONVEYOR WHEN THE PULLEY CAUGHT THE ROD AND PULLED THE EE INTO THE GUARD SHIELD.

EMPLOYEE ROCK DRILL-WENT TO KICK CENTRALIZER ARM RELEASE PLATE WITH HIS FOOT-DRILL BIT CAME OUT OF DRILLED HOLE AND CAUGHT LEFT FOOT BETWEEN CENTRALIZER ARM & DRILL BIT.

EMPLOYEE WAS GETTING DOWN OUT OF HIS HAUL TRUCK. WHEN HE GOT TO THE BOTTOM STEP, HE JUMPED DOWN TO THE GROUND FROM THE LADDER (APPROX. 3'). NOT AT THE PRESENT BUT LATER FELT PAIN IN HIS RIGHT ANKLE.

EMPLOYEE WAS CHANGING SCREENS ON SHAKER, WENT TO CLOSE CHUTE GATE WHEN HANDLE HIT EMPLOYEE ON SIDE OF FACE.

EMPL LIFTING 8" H-BEAM FELT SOMETHING PULL IN RIGHT SHOULDER.

EMPLOYEE WAS GETTING UP ONTO FORKLIFT WHEN HIS FOOT SLIPPED OFF THE STEP CAUSING HIS RT ARM WHICH WAS HOLDING ONTO THE HAND RAIL TO SLIP DOWN INTO THE HAND RAIL TWISTING HIS RT ELBOW

EMPLOYEE WAS ASSISTING IN PUTTING A STEEL PLATE BETWEEN THE CONES OF THE CRUSHING PLANT WHEN THE LIFTING LUG POPPED OFF THE PLATE CAUSING THE SHACKLE TO HIT EMPLOYEE IN FRONT OF THE LEFT EAR.

EMPLOYEE WAS DISLODGING ROCK FROM CRUSHING PLANT WITH STEEL WIRE CABLE WHEN A PIECE OF WIRE FROM CABLE PIERCED TOP SIDE OF HIS LEFT HAND

EMPLOYEE HAD BEEN PLUGGING HIS AIR NEEDLE GUN INTO THE AIR HOSE WHEN AIR AND WATER BLEW OUT INTO HIS FACE, HE WENT ON ABOUT HIS WORK AND FELT PAIN IN HIS RIGHT EYE.

EMPL WALKING ON LEVEL GROUND,STEPPED ON TREE ROOT CAUSING TREE ROOT TO ROLL,EMPL FELT SEVERE PAIN IN LOWER PART OF RIGHT LEG.

EMPLOYEE WAS DRILLING WHEN COUPLING OF DRILL HIT CENTRALIZER ARM CAUSING CHUNKS OF METAL TO CHIP OFF LODGING IN DRILLER'S LEFT ARM AND LEFT LEG.

EMPLOYEE WAS PULLING ROCK FROM CRUSHER FEEDER WHEN HIS FOOT GOT CAUGHT BETWEEN THE ROCK AND THE FEEDER CAUSING HIM TO TWIST HIS KNEE.

EMPLOYEE WAS WELDING IN CRUSHING PLANT PIECE OF WELDING SLAG POPPED AND WENT INTO HIS RIGHT EYE.

EMPLOYEE WAS GRINDING DOWN APIECE OF METAL WITH DISC GRINDER.FOREIGN OBJECT LODGED IN RIGHT EYE.

EMPLOYEE WAS LOADING ROCK FROM STOCKPILE WITH FRONT END LOADER. BLASTER SET OFF BLAST, DUE TO SEAM IN FACE, ONE ROCK FLEW FAR DISTANCE BREAKING THROUGH WINDOW ON RIGHT SIDE OF LOADER HITTING EMPLOYEE ON THE LEFT WRIST BONE.

EMPLOYEE WAS WELDING IN BED OF EUCLID TRUCK, WIND BLEW PIECE OF OREIGN OBJECT IN HIS RIGHT EYE.

EMPLOYEE WAS US3NG PIPE WRENCH BREAKING LOOSE ON EUCLID TRUCK TRANSMISSION,FELT SOMETHING PULL IN LEFT SHOULDER.

EMPLOYEE WAS CH5NGING STEEL ON DRILL STEEL WHEN A PIECE BROKE AT COUPLING LODGING IN LEFT EYE.

EMPLOYEE WAS ST5NDING ON A PLATFORM APPROX. 4' HIGH, HE JUMPED OFF AND LANDED ON A PILE OF ROCK BELOW CAUSING HIM TO INJURE HIS RIGHT ANKLE.

EMPLOYEE WAS WO9KING AT THE CRUSHING PLANT WHEN ROCKS BRIDGED UP IN THE CRUSHER FEEDER EMPLOYEE WAS PUTTING CABLE AROUND LARGE ROCK WHEN HE LOST HIS FOOTING AND FELL ABOUT 5-6 FT INTO FEEDER P AN LANDING ON H3S LEFT WRIST

EMPL GREASING F9ONT END LOADER WENT TO GO AROUND LOADER TO OTHER SIDE.GRABBED HAND RAIL AND FELT PULLING IN LEFT WRIST.

EE WS INSTALLIN1 DRIVE SHAFT ON 980B FRONT END LOADER HE WAS PULLING ON A WRENCH. HE STATED THAT HE FELT NO PAIN IN HIS FINGER BUT LATER WHEN HE WAS WASHING HIS HANDS HE NOTICED HIS LEFT HAND LITTLE FINGER 4OULD NOT EXTEND OUTWARD.

EMPLOYEE WAS WA5KING ON THE CATWALK ON CRUSHING PLANT, WAS STEPPING OVER BELT AND TRIPPED ON A ROCK, FELL ON BELT PULLING MUSCLES IN LEFT LEG

EMPLOYEE WAS GR3NDING ON A MOTOR MOUNT WITH A PORTABLE DISC GRINDER, THE GRINDER SLIPPED FROM HIS LEFT HAND-CUTTING THE MIDDLE FINGER ON LEFT HAND.

EMPLOYEE WAS OP9RATING A PORTABLE CRANE AND WAS HOOKING UP TO A LARGE TOOL CHEST WITH THEBOOM OF THE CRANE EMPLOYEE STEPPED OUT OF THE CRANE TO CHECK IF HE WAS HOOKED UP AND HIT HIS HEAD ON TH E BOOM OF THE 7RANE WHICH JAMMED HIS NECK

EMPLOYEE WAS PU7TING ON HIS WELDING HOOD TO WELD ON A PIECE OF EQUIPMENT THERE WAS SOME STEEL DUST IN THE HOOD AND IT GOT INTO HIS RT EYE

EMPLOYEE WAS BA7KING UP ROCK DRILL,STARTED TO MAKE A TURN WITH DRILL WHEN HIS LITTLE FINGER ON RIGHT HAND GOT BETWEEN THE HANDLE OF THE DRILL AND THE COMPRESSOR.

EMPLOYEE WAS HAMMERING ON A IRON CHISEL WHEN A OPIECE OF THE CHISEL CHIPPED OFF AND STRUCK THE EMPLOYEE IN THE STOMACH.EMPLOYEE RECEIVED STITCHES FROM THE METAL PIERCING HIS STOMACH.

EMPLOYEE WAS GOING UP THE LADDER ON THE FRONT END LOADER TO GREASE IT WHEN HIS FOOT SLIPPED OFF THE STEP FROM WET LIME ON HIS SHOE EMPLOYEE LANDED WITH ALL THE WEIGHT OF HIS BODY ON HIS LEFT L EG

EMPLOYEE WAS WELDING IN THE BED OF A EUCLID TRUCK AND R ECEIVED FLASH BURN ON BOTH EYES.

EMPLOYEE WAS WORKING ON A CATERPILLAR ENGINE. HE PICKED UP THE PISTON AND FELT SOMETHING PULL IN HIS LEFT THIGH.

EE WAS GRINDING A PIECE OF IRON FROM A HI-LIFT BUCKET WITH A GRINDING DISC WHEN THE DISC SLID OFF THE IRON ONTO HIS LEFT UPPER LEG APPROX 6" ABOVE THE KNEE.

EMPLOYEE WAS USING A PRY BAR TO PRY OFF A HYDRAULIC TANK ON A 988 FRONT END LOADER WHEN HE FELT A SHARP PAIN IN THE CALF OF HIS LEFT LEG

EMP WAS HAMMERING ON A METAL ROLLER WITH A SLEDGE HAMMER WHEN PIECE OF METAL FROM THE ROLLER CHIPPED OFF AND FLEW INTO EMP LEFT UPPER RT THIGH

EMPLOYEE WAS STANDING APPROX. 15 FT. FROM ANOTHER EMPLOYEE WHO WAS HAMMERING ON A METAL PIN WHEN A PIECE OF METAL FLEW FROM THERE AND WENT THROUGH THE EMPLOYEES EARLOBE WHO WAS STANDING 15 FT. AWAY.

INSIDE ROCK STORAGE BIN CLEANING ROCK OUT WHEN EANOTHER EMPL WAS INSTRUCTED BY ASST SUP TO OPEN BIN DOOR THINKING EMPLS WERE OUT OF BIN.EMPL FELL FROM BIN ONTO GROUND 13-14\.

EMPLOYEE WAS REMOVING BOLT FROM JACKHAMMER WHEN WRENCH SLIPPED-STICKING A 1" METAL SPLINTER IN PALM OF RIGHT HAND.