MSHA record for Sinclair Slope Ug #2 (mine ID 1507166). Fatalities, non-fatal incidents grouped by year, current operator and controller, and mine context.
Email me when a new MSHA incident is filed at Sinclair Slope Ug #2.
EMPLOYEE STATED HE WAS MOVING CONCRETE AT RETURN AIRSHAFT WITH A HOE, AND FELT PAIN IN LOWER BACK.
INJURED MAINT FOREMAN WAS UNDERGROUND AND STARTED HAVING CHEST PAINS.HE WAS BROUHGT OUT OF THE MINE AND TAKEN TO REGIONAL MEDCIAL CENTER BY AMBULANCE.AS OFF 06-05-91 HE WAS LISTED IN STABLE CO NDITION.
EMPLOYEE STATED BY PHONE ON 6-4-91 THAT HE HURT HIS BACK LIFTING 48" BELT ROLLER OFF 2ND M. SOUTH BELT. THIS INJURY WAS NOT REPORTED BY EMPLOYEE TO HIS FOREMAN ON 5-22-91.
EMPLOYEE STATED HE WAS LIFTING SK-60 PUMP OUT OF SUMP AND FELT PAIN IN GROIN AREA.
EMPLOYEE STATED HE WAS UNLOADING BELT ROLLERS OFF FLAT CAR WHEN HIS BACK STARTED HURTING.EMPLOYEE DIDN'T GO TO DOCTOR UNTIL 05-10-91.STARTING TIME THAT DATE 05-10-91.
WALKING UP RETURN STEPPED IN HOLE HURTING BACK AND KNEE
EMPLOYEE STATED HE WAS USING 3/4" SCOKET TO REMOVE BOLTS FROM CONT. MINER SPEED REDUCER, BOLTS WOULD NOT COME LOOSE. EMPLOYEE STOPPED ON WRENCH USING HIS FEET TO PUSH DOWN, WHEN BOLTS CAME LOO SE EMPLOYEE JARRED HIS BACK AND KNEE.
EE STATED BY PHONE ON 3-19-91 THAT HE WAS WALKING ACROSS UNIT WITH SOME ROOF BOLTS WHEN HE SLIPPED AND HIS BACK STARTED HURTING RECEIVED ACCIDENT REPORT ON 3-28-91.
EMPLOYEE STATED WHILE DRIVING TOWARD FACE IN #2 ENTRY ON #2 UNIT S/CAR HI T HOLE IN ROADWAY & BOUNCED HIM INTO CANOPY
EE STATED HE WAS LIFTING LIDS ON TAILPIECE AND FELT PAIN IN BACK.
EE STATED HE JACKED UP FRONT END OF 6X6 PUMP AND WAS PUTTINJG A BOARD UNDER IT AND FELT PAIN IN BACK.
ROOF FALL AT 3 SEAL M SOUTH SEALE #9 SEAM NO MEN OR EQUIP 5 BOLTS AND 5 SQ TIMBERS
UNINTENTIONAL ROOF FALL #2 UNTIL #5 ENTRY AT PLUS O+70. NO MEN OR EQUIPMENT INVOLVED USING 5' MCDOWELL BOLTS.
UNINTENTIONAL ROOF FALL AT 4TH S WEST RETURN IN FRONT OF #7 SEAL OLD #1 SEALS. USING 5' POINT ANCHOR BOLTS NO MEN OR EQUIPMENT INVOLVED.
UNINTENTIONAL ROOF FALL AT 4+60 1ST N.WEST PANEL OLD #3 UNIT RETURN #11 SEAM. NO MEN OR EQUIPMENT INVOLVED USING 4' RESIN BOLTS.
EE STATED HE WAS CHANGING MINER BITS WHEN HE HIT HIS THUMB WITH HAMMER CUTTING THUMB.
UNINTENTIONAL ROOF FALL.#22 X-CUT ON 3RD SW TRACK ON OLD #1. NO MEN OR EQUIP INVOLVED.USING 5'POINT ANCHOR BOLTS,CRIBS,AND RAIL BARS.
EMPL STATED HE WAS WALKING TO SLOPE MANTRIP AT START OF SHIFT WHEN HE SLIPPED & FELL ON WET SNOW COVERED GROUND. EMPL DIDN'T GO TO DR UNTIL 3/11/91 STARTED MISSING TIME ON 3/11/91.
EMLOYEE STATED A PIECE OF ROCK FELL OUT BETWEEN PINS AND HIT HIM ON UPPER LEG. WHILE HE WAS OPERATING MINER.
EMPL CUTTING METAL BAND FROM BLOCK WHEN ONE END CAME UP AND HIT HAND CUTTING IT.
EMPL STATED HE WAS LIFITING ROCK OUT OF TAILPIECE & FELT PAIN IN BACK. EMPL WORKED UNTIL 12/1790 STARTED LOSING TIME ON 12/17/90.
EMPLOYEE STATED HE WAS WALKING FROM FACE AND FELL WHEN HIS FEET BECAME ENTANGLED IN SLATE.AFTER FURTHER EXAM THIS ACCIDENT BECAME REPORTABLE AS A DOCTOR CASE.
EMPL UNLOADING TIMBERING RAILS IN TRACK ENTRY.RAILS WERE BEING PUSHED OFF FLAT CAR,RAIL KICKED BACK WHEN ONE END HIT THE BOTTOM CATCHING FINGER BETWEEN 2 RAILS.
UNINTENTIONAL ROOF FALL, #1 UNIT TRACK ENTRY AT PLUS 3+50. 60'X20'X6'. NO MEN OR EQUIPMENT INVOLVED. USING 48" RESIN BOLTS, WOOD X-BARS AND TIMBERS.
EE STATED HE WAS TIMBERING SOME TOP THAT WAS BOD. WHEN TOP STARTED TO WORK HE RAN OUT OF CROSSCUT AND RAN INTO TAILPIECE JACKPIPE.
UNINTENTIONAL ROOF FALL ON #5 ENTRY ON #1 UNIT AT PLUS 5+50. 60' X 20' X 5'. NO MEN OR EQUIPMENT INVOLVED. USING 48" RESIN BOLTS.
EMPLOYEE STATED SHE WAS JACKING MANTRIP BACK ONTO TRACK WHEN HER BACK STARTED TO HURT.
EMPL STATED HE WAS WALKING DOWN BELTLINE & STEPPED ON PIECE OF ROCK & TWISTED LEFT KNEE.
EMPLOYEE STATED HE STARTED TO STAND UP AFTER REPAIRING S/CAR WHEN HIS LEFT KNEE STARTED TO HURT.
UNINTENTIONAL ROOF FALL #6 ENTRY ON 1ST N WEST INTAKE AT SPAD 5631. 60' X 30' X 6 OR 7 USING 6' POINT ANCHOR BOLTS 5' SQ TIMBERS & 6' CRIBS. NO MEN OR EQUIPMENT INVOLVED.
EMPLOYEE STATED HE WAS WALKING IN #11 SEAM RUN-AROUND, WHE HE FELL AND HRUT HIS LEG.
EMPLOYEE STATED HE WAS OPERATING A 21S/C SHUTTLE CAR FROM DUMPING POINT TO MINER, WHEN THE TIRE ON DUMP END THREW A ROCK AND STRUCK THE BACK OF HIS NECK.
UNINTENTIONAL ROOF FALL, 3RD SOUTHWEST MAINS AT 11+20 OR 2 CROSSCUTS OUTBY SPAD 9072. 30' X 30' X 6'. NO MEN OR EQUIPMENT INVOLVED. USING 6' POINT ANCHOR BOLTS. CALLED INTO B. DAM OFFICE.
UNINTENTIONAL ROOF FALL ON #2 UNIT, LAST OPEN CROSSCUT, #2 ENTRY, 40 FEET FROM FACE. 70' X 20' X 7'. NO MEN OR EQUIPMENT INVOLVED. USING 5' MCDOWELL BOLTS. CALLED TO B.DAM OFFICE.
EMPLOYEE STATED HE WAS DRIVING SHUTTLE CAR TURNED CORNER TO SHORT AND BUMPED (LF) ELBOW AGAINST RIB OF COAL.
UNINTENTIONAL ROOF FALL, 1 CROSSCUT INBY SPAD #9274 ON #2 UNIT TRACK. 50' X 20' 6'. NO MEN OR EQUIPMENT INVOLVED. USING 5' MCDOWELL BOLTS. CALLED INTO B.DAM OFFICE.
UNINTENTIONAL ROOF FALL. 3 UNIT 3 ENTRY AT PLUS 5 AND 25. 20X20X6. USING 5 FT MCDOWELL AND WOOD CROSSBARS AND 30 INCH CRIBS. NO MEN OR EQUIPMENT INVOLOVED.
UNINTENTIONAL ROOF FALL 30FTOFF BOTTOM ON RUN AROUND TRACK NO MEN OR EQUIPMENT INVOLVED USING 5FT CONT BOLTS & STEEL RAILS CALLED INTO I NAME OFFICE
UNINTENTIONAL ROOF FALL, 5' OUTBY INTAKE AIR SHAFT. 20'X 20' X 7'. NO MEN OR EQUIPMENT INVOLVED. USING 5' CONVENTIONAL BOLTS AND STEEL RAIL BARS. CALLED INTO THE B.DAM OFFICE.
UNINTENTIONAL ROOF FALL,1ST SOUTH EAST SUB MAIN,1 CROSSCUT OUTBY SPAD 3055 IN FRONT OF #2 SEAL.30'X20'X5'.USING 4' RESIN BOLTS AND 5' SQ TIMBERS.NO MEN OR EQUIPMENT INVOLVED.CALLED TO B DAM OF FICE.TALKED TO (NAME)
EMPL STATED HE WAS LIFTING WOOD CROSSBAR TO PUT ON ROOF BOLTER WHEN BACK STARTED TO HURT.
EMPLOYEE WAS PULLING ON PINNER CABLE TO HOOK IT TO TRANSFORMER. STATED HIS SHOULDER (LEFT) WAS HURTING.
EMPLOYEE STATED HE WAS OPERATING CONT MINER WITH HAND ON REMOTE CONTROL BOX WHEN A PIECE OF GOB FELL & HIT HIS HAND FINGER WAS CAUGHT BETWEEN GOB & REMOTE CONTROL BOX
UNINTENTIONAL ROOF FALL ON MAIN WEST RETURN 200' OUTBY SPAD 3055. 160' X 20' X 8'. NO MEN OR EQUIPMENT INVOLVED. USING 5' BOLTS AND 5' SQ TIMBERS. CALLED INTO BOULDER DAM OFFICE.
UNINTENTIONAL ROOF FALL, 34D S.WEST NEUTRAL ENTRY, 1 X-CUT OUTBY SPAD #9147 AT #33 X-CUT. 60'X20'X6'. NO MEN OR EQUIPMENT INVOLVED. USINING 5' POINT ANCHOR BOLTS.
UNINTENTIONAL ROOF FALL, 3RD S.WEST ENTRY. 1 X-CUT OUTBY SAPD #9112 AT #25 X-CUT. 60'X60'X8'. NO MEN OR EQUIPMENT INVOLVED. USING 5' POINTANCHOR BOLTS.
EMPL STATED HE WAS LIFITING BATTERY COVERS ON HOIST CAR WHEN HE FELT PAIN IN SIDE. EMPL DIDN'T GO TO DR UNTI 6/21/91 STARTED LOSING TIMBE ON 6/24/91.
UNINTENTIONAL ROOF FALL, 2ND SOUTHWEST INTAKE AIR COURSE, SPAD #4355. 25' X 20' X 6'. NO MEN OR EQUIPMENT INVOLVED. USING 48" RESIN AND STRAIGHT TIMBERS. CALLED INTO B. DAM OFFICE 7-2-90.
UNINTENTIONAL ROOF FALL ON 2ND SOUTHWEST INTAKE AIR COURSE, SPAD #4316. 40'X20'X6'. NO MEN OR EQUIPMENT INVOLVED. USING 48" RESIN AND STRAIGHT TIMBERS.
LOADING S CAR WITH COAL TIRE RAN OVER PC OF CAOL IT FLEW OUT HIT KNEE HE TURNED BACK NOW HAS BACK PAIN
EMPL CHANGING HOSE ON UNIT SCOOP,STRETCHING OVER TIRE FELT PAIN IN LOWER BACK.
EMPLOYEE STATED HE WAS WALKING TO CHECK CONVEYOR TAIL PIECE WHEN HE SLIPPED ON A SLIGHT BANK AND TWISTED LEFT KNEE.
UNINTENITONAL ROOF FALL ON 2 UNIT 5 ENTRY 1 CROSSCUT INBY SPAD 9062 25X20X5 TO 6 FT NO MEN OR EQUIPMENT INVOLVED USING 5 FT MCDOWELL BOLTS.
EMPL BENDING OVER AND IN PROCESS OF CLEANING DUST BOX OUT IN X-CUT BETWEEN #1 & #2 ENTRY ON #2 UNIT,WHEN PIECE OF ROCK FELL OUT BETWEEN PINS AND RIB HITTING EMPL ON BACK.NO BROKEN BONES.
UNINTENT. RF FALL 4 ROOM 3 UNIT 20' 20' 5' 6'. USING MCDOWELL BOLTS 5'
EMPLOYEE STATED HE WAS BENDING OVER PINNER TO GET CHAIN HANGER PLATE WHEN A PIECE OF GOB FELL OUT & HIT HIM ON BACK CAUSING HIS HEAD TO GO FORWARD & HIT PINNER
CHANGING FUEL FILTER ON DOZER STEPPED UPON FIRST STEP FOOT SLIPPED OFF AND HIS BODY SWUNG AROUND AND SSTRUCK RT SIDE ON FRONT OF DOZER
UNINTENTIONAL ROOF FALL ON #2 UNIT AT 55+60 BETWEEN XCUTS #2 & #3 40FTX20FTX8FT NO MEN INVOLVED USING 5FT MCDOWELL BOLTS CALLED TO I NAME TALKED TO I NAME
EE STATED HE WAS DRIVING S/CAR AND IN THE PROCESS OF TURNING INTO RT CROSSCUT. WHEN S/CAR HIT INBY RIB, CAUSING EE TO HIT HEAD ON CANOPY, HURTING HIS NECK AND BACK.
RF FALL 3 UNIT TRACK AT SPAD 8530 18' X 20' X 6' NO MEN OR EQUIP. INVOLVED
UNINTENTIONAL RF FALL SPAD 22 AND 23 CROSSCUTS ON 3RD SW BELT NO MEN INVOLVED COVERED THE S W BELT USING ANCHOR BOLT AND 5' TIMBERS
EMPLOYEE STATED HE WAS THROWING A BOX OF MIENR BITS ON SCOOP, WHEN HE FELT PAIN IN LOWER BACK AND SIDE.
UNINTENTIONAL FALL OF ROOF ON TRCK ENTRY #2 UNIT AT 41/30. 20' X 45' X 6'.USING 5'MCDOWELL BOLTS,NO MEN OR EQUIP INVOLVED.
INJURED STATED HE WAS OPERATING A OPEN TYPE MANTRIP AND PULLING A WIRE ROPE.HE WAS WATCHING THE WIRE ROPE AND HE TRAVELED UNDER A 4" WATER LINE AND STRUCK A COUPLING CAUSING A LACERATION ABOVE THE LEFT EYE.
INJURED STATED HE WAS LIFTING A THIRTY GALLON OIL DRUM ONTO A MECHANIC CART TO TRANSPORT TO MINER WHEN HE FELT PAIN IN LOWER BACK.
UNINTENTIONAL ROOF FALL ON #2 UNIT,#1 ENTRY AT 36/40. 35' X 20' X 5-6'. USING MCDOWELL ROOF BOLTS NO MEN OR EQUIP INVOLVED.
A ROOF FALL OCCURRED ON THE 2 SOUTHWEST PANEL, UNIT #2 ENTRY #2 SPAD #35+00. THE ROOF FALL MEASURED 20' LENGTH, 18' WIDTH AND 6' THICKNESS. THE AREA WAS SUPPORTED WITH 5' RESIN MCDOWELL BOLTS.
A ROOF FALL OCCURRED ON THE 1ST NORTH EAST PANEL, UNIT #3, #3 ENTRY, SPAD #7+50. THE ROOF FALL MEASURED 20' LENGTH, 18' WIDTH, 6' THICKNESS. THE AREA WAS SUPPORTED WITH 5' RESIN MCDOWELL BOLTS .
INJURED STATED HE WAS TIGHTENING REGULAR CONVEYOR TAIL PIECE JACKS WHEN THE REGULAR JACK HANDLE SLIPPED PUT OF THE JACK AND STRUCK RIGHT SIDE OF FACE AREA.
UNINTENTIONAL ROOF FALL ON #2 UNIT AT #6 ENTRY.35'X20'X6'X7'.NO MEN OR EQUIPMENT INVOLVED.USING 6' MCDOWELL BOLTS.CALLED TO BEAVER DAM.TALKED TO (NAME).
UNINTENTIONAL ROOF FALL ON 2 UNIT IN 5 ENTRY 30 X 20 X 6TO 7 NO MEN OR EQUIPMENT INVOLVED. USING 6 FT MCDOWELL BOLTS. CALLED INTO B DAM TALKED TO J.
ROOF FALL OCCURRED ON 2NS SOUTH WEST PANEL RETURN ENTRY AT STATION 21+00 MEASURING 40' LENGTH, 18' WIDTH & 6TH THICK. AREA WAS SUPPORTED WITH 5' TENSION BELTS.
A ROOF FALL OCCURRED ON THE 2ND SOUTH WEST PANEL ONE CROSSCUT INBY SPAD #8494 IN #7 ENTRY, WHICH MEASURED 15' LENGTH, WIDTH 18' AND 6' THICK. THE AREA WAS SUPPORTED WITH 6' GROUTED BOLTS AND S AWED TIMBERS DOWN EACH RIB.
UNINTENTIONAL ROOF FALL, 4 CROSSCUTS OUTBY SPAD #7146 ON 1ST SOUTH EAST MAIN RETURN. 40' X 30' X 7'. NO MEN OR EQUIPMENT INVOLVED. USING 6' POINT ANCHOR BOLTS AND TIMBERS. CALLED IN TO BEAVER DAM.
UNINTENT RF FALL ON 1 UNIT RETURN SPAD 6810 100' 20' 6' TO 7'. NO MEN OR EQUIP INVOLVED
INJURED STATED HE WAS RIDING IN A GOODMAN MULE MANTRIP AND WHEN TRYING TO HOOK UP TO ANOTHER GOODMAN MULE MANTRIP THE TRIPS BUMPED PRETTY HARD AND HE STRUCK A MANTRIP WHICH STRAINED HIS LOWER BACK.
EMPLOYEE STATED HE WAS HOLDING TOP BELT UP SO ANOTHER EMPLOYEE COULD REPLACE BELT ROLLER.HE FELT PAIN IN BACK.
UNINTENTIONAL ROOF FALL 1 CROSS CUT INBY SPAD #6466 ON 3RD SOUTHWEST INTAKE. 40' X 20' X 7'. NO MEN OR EQUIPMENT INVOLVED. USING 6' POINT ANCHOR BOLTS AND 6" X 6" SQ. TIMBERS. CALLED BEAVER DA M OFFICE. TALKED TO I.NAME.
UNINTENTIONAL ROOF FALL ONE X CUT INBY SPAD #8268 AT S WEST PANEL OFF 2ND N EAST MAIN 40' X 20' X 7'. NO MEN OR EQUIPMENT INVOLVED USING 5' RESIN BOLTS.
OCC ON SW PANEL OF NE MAIN 2 X CUT OUBY SPAD 8359 20'L 40'W 8'H SUPPORTED WIHT 5' TENSION BOLTS ON 5 CENTERS
A ROOF FALL OCCURRED ON THE 1ST SOUTH EAST BELT AND TRACK ENTRY 2 AT ONE X-CUT OUTBY SPAD #7144 MEASURING 25' LENGTH, 60' WIDTH AND 10' THICK. THE AREA WAS BELTED WITH 6' GROUTED BOLTS. TRACK WAS RAIL BARRED WTIH CRIBS, BELT ENTRY WAS STRAIGHT LEGGED AND CRIBBED.
REMOVING CABLE FROM CROSS OVER HANGERS CABLE SLIPPED CAUGHT HAND IN CABLE IN HOOK
INJ DRILLING HOLE IN ROOF TO INSTALL ROOF BOLT.DRILL STEEL HUNG IN HOLE.TRYING TO DISLODGE PINNER STEEL THE STEEL SUDDENLY DROPPED OUT OF HOLE AND CAUGHT FINGER BETWEEN DRILL STEEL AND ROTATIO N HEAD.
A ROOF FALL OCCURRED OUTBY #1 UNIT ON SUPPLY LOAD AT SPAD #8187 MEASURING 20' IN LENGTH 20' WIDTH AND 7' THICKNESS.THE AREA WAS SUPPORTED WITH 6' POINT ANCHOR BOLTS.
A ROOF FALL OCCURRED ON THE 4TH SOUTHWEST BELT ENTRY ONE X-CUT OUTBY SPAD #6649 MEASURING 30' LENGTH 20' WIDTH AND 6' TO 7' THICKNESS.THE AREA WAS SUPPORTED WITH 6' POINT ANCHOR BOLTS AND STRA IGHT LEGS ON 5' CENTER ON BOTH SIDES OF BELT.
EMPLOYEE STATED HE WAS OPERATING A TEN TON MOTOR, AS HE WENT UNDER THE M. SOUTH BELT, HE HIT HIS HEAD ON GUARD, CUTTING HIS HEAD ABOVE RT. EYE.
ROOF FALL OCCURRED ON 6TH SW ,2 X-CUTS OUTBY SPAD 7815 MEASURING 3 X-CUT LONG X 20'WIDE X 8'HIGH.AREA WAS SUPPORTED WITH 6' POINT ANCHOR BOLTS.
UNINTENTIONAL ROOF FALL 1 CROSS CUT INBY SPAD #5497 30' X 20' X 8' NO MEN OR EQUIPMENT INVOLVED USING 48" RESIN BOLTS AND 5'SQ TIMBERS CALL TO NAME ON 10/12/89
INJ OPERATING 10 TON LOCOMOTIVE ON NW TRACK AND WHEN TRAMMING DOWN SLIGHT GRADE,STRUCK FLATCAR OF STEEL RAILS WHICH WAS PART OF SUPPLY TRIP SITTING ON THE TRACK.
UNINTENTIONAL ROOF FALL, 1 X-CUT OUTBY SPAD #7960 ON 2ND S. WEST PANEL. 20' X 20' X 6'. USING 5' POINT ANCHOR BOLTS AND 5' SQUARE TIMBERS. NO MEN OR EQUIPMENT INVOLVED. 0/5/89.
FALL OCC ON 2 SOUTH WEST TRACK 20'W 25'L 6' T SUPPRTED WITH 48' RESIN BOLTS 90 RAIL BARS AND CRIB BARS
ROOF FALL OCCURRED IN OLD NORTH WEST MAIN RETURN ENTRY ONE CROSS CUT INBY SPAD #3378. LENGTH 20' WIDTH 20' THICNESS APPROX 6'. AREA WAS SUPPORTED WITH 48" RESIN BOLTS 90# RAIL BARS & CRIBS.
A ROOF FALL OCCURRED APPROXIMATELY 25'LX18'X5' TO 6'H IN THE MAIN SOUTH BELT ENTRY BETWEEN #1 AND 2 CROSS CUTS. THE AREA WAS SUPPORTED WITH A 2" ROOF BOLTS, RAIL BARS AND SQUARE TIMBERS AND S TRAPS.
INJURED STATED HE WAS HELPING INSTALL STEEL ARCHES FOR ROOF SUPPORT & WHILE INSTALLING LAGGING BETWEEN ARCHES HE CAUGHT HIS INDEX & MIDDLE FINGERS BETWEEN LAGGING
INJURED STATED HE WAS REMOVING A SMALL ROCK FROM THE HAULAGE ROAD & AS HE ATTEMPTED TO THROW ROCK INTO HIS SHUTTLE CAR HE MISJUEDGED & CAUGHT FINGER BETWEEN ROCK & FRAME OF SHUTTLE CAR.
INJURED STATED HE WAS PULLING AND LIFTING ON CONT MINER CABLE TO KEEP IT OUT OF WAY WHEN HE FELT PAIN IN LOWER BACK.
INJURED STATED HE WAS CHECKING A WATER PUMP WHEN ONE OF THE WATER HOSES CAME APART, AS HE JUMPED OUT OF WAY, HE WRENCHED HIS KNEE.
HOIST CAR WAS BEING BROUGHT OUT OF MINE FROM #9 SEAM, WHEN AXLE BROKE. NO EMPLOYEES WERE ON HOIST CAR OR IN SLOPE WHEN AXLE BROKE. AT 3:20 PM HOIST CAR WAS REPAIRED AND RETESTED. ACCIDENT WAS CALLED IN B.DAM OFFICE.
INJURED STATED HE WAS HELPING ON CONT MINER AND WAS PULLIUNG ON THE MINER CABLE TO KEEP IT OUT OF WAY WHEN HE FELT PAIN IN LOWER BACK.
EMPLOYEE STATED HE WAS OPERAT ING SHUTTLE CAR WHEN A ROCK LODGED BEHIND THE WHEEL UNIT & AS HE WAS ATTEMPTING TO REMOVE THE ROCK BY HAND HE HURT HIS BACK
EMPLOYEE STATES HE WAS RIDING IN A GOODMAN MULE MANTRIP TRAVELING FROM UNIT TO BOTTOM, WHEN THE MANTRIP STUMPED THE TRACK & STRUCK RAILS HAND WHICH JARRED OR VIBRATED HIM
EMPL STATED HE WAS CARRYING MINER PARTS FROM END OF TRACK TO MINER WHEN HE FELT PAIN IN LOWER BACK.
UNITENTIONAL ROOF FALL, ONE CROSSCUT OUTBY SPAD #7918 ON 2ND EAST. 65'X20'X10'. NO MEN OR EQUIPMENT INVOLVED. USING 72" BOLTS.
UNINTENTIONAL ROOF FALL ON 3RD SOUTHWEST AT SPAD #6689.22'X20'X7'.NO MEN OR EQUIPMENT INVOLVED. USING 48: RESIN BOLTS AND SQUARE LIMBERS.
UNINTENTIONAL ROOF FALL ON #4 ENTRY AT FACE AREA ON #2 UNIT.20'X20'X6'.NO MEN OR EQUIPMENT INVOLVED USING 36" RESIN BOLTS.CALLED IN TO BEAVER DAM.
EMPLOYEE STATED ONE MAN TRIP SLID BACK DOWN A HILL AND RAN INTO HIS TRIP.
EMPLOYEE STATED WHILE SETTING ON RIB WATCHING MINER OPERATOR A PIECE OF GOB, FELL FROM ROOF HITTING EMPLOYEE ON HEAD. EMPLOYEES MINE CAP CAME DOWN AND HIT HIM IN THE NOSE BREAKING IT.
UNINTENTIONAL ROOF FALL IN NEUTRAL ENTRY ON #1 UNIT, 4 X-CUTS OUTBY SPAD #7872. 20' X 20' X 7'. NO MEN OR EQUIPMENT INVOLVED. USING 5' POINT ANCHOR BOLTS.
UNINTENTIONAL ROOF FALL AT SPAD #6953 ON 5TH S. WEST RETURN. 20' X 20' X 6'. NO MEN OR EQUIPMENT INVOLVED. USING 48" RESIN BOLTS AND TIMBERS. CALLED TO B. DAM OFFICE.
UNINTENTIONAL ROOF FALL AT SPAD #6965 ON 5TH S., WEST RETURN. 20'X20'X6'. NO MEN OR EQUIPMENT INVOLVED. USING 48" RESIN BOLTS AND TIMBERS.
A ROOF FALL OCCURRED OUTBY FACE OF #1 ENTRY,3RD SOUTH EAST OFF 1ST SOUTH WEST UNTI #4 AT SPAD #7804.WIDTH 18' IN LENGTH 40' IN HEIGHT 10'.THE AREA WAS BOLTED WITH 5' PINT ANCHOR & CROSS BARS W ITH CRIBS.
A ROOF FALL OCCURRED AT FACE #2 ON UNIT #2 1ST SOUTH OFF 2ND NORTH EAST LENGTH 30' WIDTH 18' HEIGHT 10' THE AREA WAS BOLTED WITH 6' POINT ANCHOR BOLTS,RAIL BARS INSTALLED ON CRIBS.
INJURED STATED HE STRAINED RIGHT KNEE WHILE PULLING ON CONTINUOUS MINER CABLE.
A ROOF FALL OCCURRED AT THE FACE OF #2 ENTRY ON #2 UNIT SOUTH PANEL OFF 2ND NORTH EAST PANEL AT 3 + 00. WIDTH 20; LENGTH 20', HEIGHT 10'. THE AREA WAS SUPPORTED WITH 6' MCDOWELL BOLTS.
LOADING CAR OF COAL PC OF OAL FLEW OUT FORM UNDER S CAR TIRE STRUCK HIM ON L KNEE.
EMPLOYEE STATED HE WAS LIFTING TIMBERS, WHEN HIS LITTLE FINGER WAS CAUGHT BETWEEN TWO 5' TIMBERS.
LIFTING BAG OF ROCKDUST FELT PAIN IN BACK LOSING TIME ON 5-15-89
EMPLOYEE STATED THAT A CABLE BLEW UP IN FRON OF HIM WHEN TURNED TO RUN HE FELL TWISTING HIS LEFT KNEE.
EMPLOYEE STATED HE WAS CHANGING OUT BOWL ON PUMP EMPLOYEE LIFTED ON 4IN WATER LINE & FELT PAIN IN LOWER BACK EMPLOYEE WAKED THE REST OF SHIFT & RETURNED ON 041189 WAKED UP T HRU 041389 STARTED LOSING TIME THEN
UNINTENTIONAL ROOF FALL/25'INBY SPAD#7396 ON 3RD EAST RETURN.40'X20'X8'.NO MEN OR EQUIPMENT INVOLVED.USING 48" RESIN BOLTS.
EMPLOYEE STATED HE WAS SHOVELING ON BELT WHEN SHOVEL WAS CAUGHT IN BELT AND SHOVEL CAME BACK AND HIT HIM IN RIBS.
UNINTENTIONAL ROOF FALL ON WEST RETURN. USING 6 FOOT POINT ANCHOR BOLTS, WITH TURN BOLTS. NO EQUIPMENT OR MIN.
EMPLOYEE STATED HE WAS GETTING OFF MAN-TRIP WHEN HE STEPPED ON CRIB BLOCK AND TWISTED HIS LEFT KNEE.
UNINTENTIONAL ROOF FALL ON 2ND M. EAST RETURN USING 36" RESIN BOLTS NO MEN OR EQUIPMENT.
UNINTENIONAL ROOR FALL. 2 CROSSCUTS INBY SPAD #6848 ON 5TH SOUTH WEST RETURN. 100' X 20' X 6 OR 7'. NO MEN OR EQUIPMENT INVOLVED. USING 6' POINT ANCHOR BOLTS AND 6' SQ. TIMBERS.
UNINTENTIONAL ROOF FALL. SPAD #6366 ON 3ES S.W. RETURN. 20' X 20' X 6'. NO MEN OR EQUIPMENT INVOLVED. USING 6' POINT ANCHOR BOLTS AND SQ. TIMBERS.
EMPLOYEE STATED HE WAS LIFTING A TIMBER AND FELT PAIN IN LOWER BACK.
UNINTENTIONAL ROOF FALL #6 CROSSCUT ON 1ST SOUTH EAST RETURN NO MEN OR EQUIPMENT INVOLVED 100 FT X 20 FT X 12 FT USING 6 FT POINT ANCHOR BOLTS AND SQUARE TIMBERS CALLED INTO BEAVER DAM
EMPLOYEE STARTED WHILE PULLING ON MINER CABLE HE HURT HIS BACK. ACCIDENT WAS NOT REPORTED TO SUPERVISOR UNTIL (2-14-89).
INTENTIONAL ROOF FALL. THE COMPANY SHOT THE FALL DOWN FOR SAFETY REASONS. #21 CROSSCUT ON MAIN SOUTH TRACK. 30-40' X 20' X 10-12'. NO MEN OR EQUIPMENT INVOLVED. USING 6' POINT ANCHOR BOLTS AND RAIL BARS. CALLED INTO BEAVER DAM OFFICE.
UNINTENTIONAL ROOF FALL ON #3 RETURN ONE CROSSCUT OUTBY SPAD #6259 150 FT X 20 FT X 6 FT NO MEN OR EQUIPMENT INVOLVED USING 6 FT POINT ANCHOR BOLTS AND SQUARE TIMBERS
UNINTENTIONAL ROOF FALL ON #O UNIT #5 ENTRY AT SPAD #7321 APPROX 500' INBY.20'X25'X6'.NO MEN OR EQUIPMENT INVOLVED.USING 6' POINT ANCHOE BOLTS.CALED INTO B DAM ODDICE 01-24-89.
UNINTENTIONAL ROOF FALL ON #3 UNIT, 6 CROSSCUTS OUTBY UNIT TAILPIECE. 25' X 20' X 7'. USING 6' POINT ANCHOR BOLTS AND SQUARE 6" X 6" X6" TIMBERS. NO MEN INVOLVED. COVERED APPROX. 500' OF BELTI NG.
EMPLOYEE STATED HE STRAINED HIS GROIN WHILE PULLING ON PIPE WITH PIPE WRENCH EMPLOYEE WOPRKED FROM 011789 TO 021789 STARTED LOSING TIME ON 021889 ACCIDENT WAS NOT REPORTABLE UNTIL 021889
EMPL STATED WHILE UNDERGROUND HE BECAME SICK.
EMPLOYEE STATED HE WAS REMOVING CENTER SECTION OF SCOOP WITH CUTTING TORCH AND USING THE OVERHEAD HOIST TO HOLD TENSION ON THE CENTER SECTION. WHEN EMPLOYEE STARTED TO CUT AFTER SEVERAL CUTS HAD BEEN MADE, CENTER SECTION CAME LOOSE AND HIT EMPLOYEE IN JAW. BREAKING IT IN 3 PLACES.
EMPLOYEE STATED HE WAS PULLING ON PIPE AND FEET SLIPPED OUT FROM UNDER HIM CAUSING HIM TO FALL.
UNINTENTIONAL ROOF FALL 2ND SW BELT 1 X-CUT INBY SPAD #4386 AT #27 X-CUT.20' X 20' X 7'.NO MEN INVOLVED.USING 6' POINT ANCHOR BOLTS,SQUARE TIMBERS & CRIBS.
EMPLOYEE STATED HE WAS HELPING LOAD STEEL RAILS ONTO SCOOP WHEN HE FELT PAIN IN BACK
ROOF FALL ON 3 RD S W PANEL 3 X CUTS INBY SPAD 6366. NO MEN OR EQUIPMENT INVOLVED. USING 48" RESIN BOLTS TIMBER SQUARE. CALLED INTO V DAM ON 12-14-88
EMPLOYEE STATED HE WAS HELPING INSTALL A TRACK IDLER ON CONT. MINER. EMPLOYEE'S HAND WAS CAUGHT BETWEEN IDLER AND PAN OF MINER.
UNINTENTIONAL ROF FAL ON AMIN SO. AT SPAD #413. 150' X 20' X 5' & OR -. NO MEN OR EQUIP. INVOLVED USING 5' BOLTS TIMBERS CRIBS AND WOOD X-BARS. CALLINTO B. DAM ON 10-3--88
INJURED STATED HE WAS HELPING ON A DOUBLE BOOM BOLTER AND HAD JUST INSTALLED HIS INSIDE BELT AND WAS DISMOUNTING SEAT ON BOLTER WHEN A PIECE OF GOB OR ROCK FELL BREAKING OF IN FRONT OF ATRS A ND OUTSIDE BOLT WHICH STRUCK HIM IN LOWER BACK. THE ROCK OR GOB WAS APPROX. 2 1/2' X 59" X 60".
INJURED STATED HE WAS HANDLING DUSTER HOSE OF A BANTAM ROCK DUSTER WHEN A SMALL PIECE OF GOB FELL OUT FROM BETWEEN PERMANENT ROOF SUPPORTS AND STRUCK HIS LOWER BACK.
EMPLOYEE STATED THAT PINNER WAS TWINING AROUND IN #4 ENTRY TO PIN LEFT WING.EMPLOYEE WALKED BEHIND PINNER AND A PICE OF GOB FELL ON HIM.HURTING HIS AHND HIP AND LEG.
EMPLOYEE STGATES HE WAS HELPING REPAIR A MINER POT WHEN HE PULLED HIS RT.HAND ACROSS A PIECE OF METAL WITH A SHARP EDGE RESULTING IN A LACERATION WHICH REQUIRED SUTURES
ROOF FALL OCCURRED TWO X-CUTS OUTBY #3 UNIT CONVEYOR BELT TAIL ROLLER AT SPAD #6725. ROOF WAS SUPPORTED WITH SIX FOOT POINT ANCHOR BOLTS & TIMBERS. AREA AROUND FALL WAS CRIBBVED WITH TIMBERS
EMPLOYEE STATES HE WAS REACHING DOWN TO LIFT BELT CHANNELS OFF THE MINE FLOOR WHEN HE FELT PAIN IN THE LOWER BACK AREA
WHILE HELPING ROCK DUST MAJIN WEST TRACK AND BELT LINE, HE WAS CAUGHT BETWEEN TOP OF TEN TON MOTOR AND 90# STEEL RAILS INSTALLED FOR ROOF SUPPORT.
INJURED STATED HE WAS DISMOUNTING FROM THE DECK OF A BATTERY SCOOP WHICH HAS A CANOPY WHEN HE TWISTED HIS LEFT KNEE.
UNINTENTIONAL ROOF FALL 4 CROSSCUTS OUTBY 1ST NORTH EAST BELT HEADER ONE CROSSCUT INBY SPAD 5203 18X20X7FT NO MEN INVOLVED CALL INTO 5-27-88.
A FIRE OF UNKNOWN ORIGIN WAS DISCOVERED BY TWO ROCK DUSTERS AT APPROX 5:15 AM ON MAIN WEST BELT BETWEEN #5 & #6 CROSSCUTS MEN WERE REMOVED FROM MINE AND THE FIRE WAS EXTINGUISHED AT 6:00 AM
EMPLOYEE STATED HE WAS HELPING THROW A COAL FLOP GATE & FELT PAIN IN LOWER BACK ACCIDENT NOT REPORTABLE UNTIL 060388
INJURED WAS USING A LIFTING JACK TO RERAIL A BOO GOODMAN TRIP WHEN THE JACK SLIPPED AND JACK HANDLE STRUCK HIM UNDER THE CHIN
EMPLOYEE STATED SHE WAS CLEANING UP LOOSE MATERIAL OFF THE SLOPE WHENHER LEFT FOOT WAS CAUGHT UNDER FRONT OF SUPPLY CAR
EMPLOYEE STATED HE WAS UNLOADING BELT ROLLERS WHEN HE FELT PAIN IN HIS LIFT SHOULDER
EMP. STATED HE STRUCK A METAL MOUNT BRACKET IN THE OPERATING CAB WHILE MOVING BACK HOE, TO A NEW DIGGING LOCATION. EMP. WORKED FROM 4-7-88 TO 5-2-88. STARTED LOSING TIME ON 5-2-88. ACCIDE NT WAS NOT REPORTABEL UNTIL 5-2-88.
INJ. STATED HE WASS UNLOADING ROUND TIMERS AND FROM AS SUPPLY TRAILER AND WHILE THROWING THE TIMBERS HE FELT PAIN IN GROIN AREA.
EMPLOYEE STATED HE WAS INSTALLING SHEAR JACK ON MINER. HANDS SLIPPED OFF JACK AND HIS FINGERS WERE CAUGHT BETWEEN JACK AND MOUNTING BRACKET.
EMP STATED HE W5S LIFTING TIMBER AND FELT PAIN IN LOWER BACK
EMPLOYEE STATES3HE WAS OBSERVING THE MINER CUTTING COAL IN THE ENTRY, WHEN A PIECE OF DRAW SLATE FELL FROM AROUND PERMANENT ROOF SUPPORT AND STRUCK HIM A GLANCING BLOW TO THE LOWER BACK AREA.
EMPL LIFTING TI4BER AND FELT PAIN IN BACK.
EMPL LOWERING B2OM SAFETY JACK WHEN HE CAUGHT FINGER BETWEEN BOLTER FRAME AND SAFETY JACK.
UNINTENTIONAL R2OF FALL ON #1 UNIT, #5 ENTRY 3 CROSSCUTS FROM FACE. 50' X 20' X 9'. NO MEN OR EQUIPMENT INVOLVED. USING 6' POINT ANCHOR BOLTS 6' CRIBS 6' TIMBERS
EMPLOYEE STATED3HE WAS WALKING DOWN TRACK ENTRY AND HIT HIS HEAD ON RAIL BAR. HURTING WECK AND SHOULDER.
EMPL OPERATING 4INER BY REMOTE,SMALL PIECE OF RIOCK FELL HIT HIM ON LITTLE FINGER,CUTTING IT.AVULSION TO LITTLE FINGER RIGHT HAND.
UNINTENTIONAL R2OF FALL ON #1 UNIT, 3 X-CUTS OUTBY BASE, INTERSECTIONS 4,5,6, 80 FEET X 20 FEEET X 9 FEET. NO MEN OR EQUIPMENT INVOLVED..
EE STATED HE WA8 MAKING A TURN THRU X-CUT GOING DOWN HILL WHEN THE BRAKES ON HIS S/C WENT OUT. EE TURNED S/C INTO RIB, CAUSING HIM TO BE THROWN FROM CAR.
UNINTENTIONAL R2OL FALL ON #3 UNIT, #5 ENTRY. 20'X18'X6'. NO MEN OR EQUIPMENT INVOLVED. USING 6' POINT ANCHOR BOLTS.
EMPLOYEE STATED3HE WAS LIFTING BELT ROLLER & FELT PAIN IN LOWER BACK
EMPLOYEE STATED3WHILE UNDER GROUND HIS ARM SWELLED UP
EMPLOYEE STATED3HE WAS WALKING DOWN BELTLINE, WHEN HE STEPPED ON WATER LINE AND FELL.
UNINTENTIONAL R2OF FALL.1 X-CUT INBY TAIL PIUECE ON #3 UNIT. 40'X20'X6'.NO MEN OR EQUIPMENT INVOLVED.USING 6' POINT ANCHOR BOLTS. CALLED TO B.DAM ON 08/10/87.TALKED TO FRANK DUPREE.
UNINTENTIONAL R2OF FALL, 18'X18'X5',6 CROSSCUTS ON 2ND NORTH WEST TRACK. NO MEN OR EUIPMENT INVOLVED. 6' POINT ANCHORS, 6X6 TIMBERS.
EE STATED HE W5S MOVING ROCK BY HAND TO MAKE TOOM FOR A TIMBER TO BE SET. WHEN A PIECE OF ROCK FELL & HIT ON HEAD SHOULDER & WRIST.
UNINTENTIONAL R2OF FALL AT THE #9 CROSSCUT ON THE NORTHEAST BELT.NO MEN OR EQUIPMENT INVOLVED.30' X20' X6'.USING CRIBS AND TIMBERS.
EMP STATED HE W5S SANDING TRACK WHEN HE RAISED UP TO SEE WHERE HE WAS AT. HIS HEAD WAS CAUGHT BETWEN RAIL BAR AND MOTOR
EMP STATED HE S7EPPED OFF SUPPLY MOTOR AND WRENCHED HIS RIGHT KNEE
EMPLOYEE STARTE8 HE WAS UNLOADING WOOD CROSS BARS WITH ANOTHER EMPLOYEE WHEN ANOTHER WOOD CROSS BAR FELL ON HIS FOOT CHIPPING BONE IN ANKLE
HE WAS THROWING3TIMBERS ONTO MAINTANCE CART. WHEN TIMBER CAUGHT ON CABLE, CAUSING HIS FI NGER TO BE CAUGHT BETWEEN CART AND TIMBER. MASHING MIDDLE FINGER ON LEFT HAND.
EMPLOYEE HE WAS3CHANGING OUT CONTROL BREAKER ON 100 HP BELT STARTING BOX. EMPLOYEE DID NOT TURN POWER OFF H E RECIEVE ELECTRIAL SHOCK WHICH BURNED HIS HAND ALSO CAUSED HIM TO FALL BACK WHICH D ISLOCATED HIS R7 SHOULDER.
EMPLOYEE STATED3HE WAS OPERATING SUPPLY MOTOR ON 2ND WEST SUPPLY ENTRY, WHEN HE DIDNT GET DOWN AND HIS HEAD, WAS CAUGHT BETWEEN MOTOR AND STEEL RAIL BAR. HURTING HEAD AND NECK.
EMPL OPERATING 8COOP AND HIS BACK STARTED HURTYING.
UNINTENTIONAL R2OF FALL ON #1 UNIT, #4 ENTRY, 6 X-CUTS FROM FACE. NO MEN OR EQUIPMENT INVOLVED. USING 48" RESIN BOLTS, WOOD CROSS BARS.,
UNINTENITONAL R2OF FALL ON 11 SEAM SLOPE 25 FT X 16 FT X 8 FT. NO MEN OR EQUIPMENT INVOLVED. USING STEEL SETS AND LAGGING, CRIB BLOCKS ABOVE.
UNINTENTIONAL R2OF FALL 1 ST S.W. PANEL 100 INBY SPAD 5033. 100X20X4 TO 5 FT USING 48 INCH RESIN BOLTS AND TIMBERS. NO MEN OR EQUIPMENT INVOLVED.
EMPLOYEE STAED 2E WAS TRAMMING MINER AND TWISTED KNEE WHILE WALKING
EE STATED WHILE3SHOVELING ON BELT A SMALL PIECE OF ROCK FELL OUT OF ROOF HITTING HIM ON BACK. EE STATED HIS BACK & KNEE WAS HURT. EE RETURNED TO WORK ON 12-13-86 & HAD WORKED UP TO NOW WITH OUT ANY PROBLEM8.
EMP STATED HE W5S HELPING REMOVE I BEAM FROM SUPPLY CAR I BEAM SLIPPED OFF CAR AND FELL ON HIS FOOT
EMPLOYEE STATED3HE WAS REPAIURING SCOOP CONTROL SWITCH. HE TURNED A BREAKER ON TO TEST SCOOP. SCOOP WOULD NOT START DUE TO BAD CONNECTION. SCOOP SUDDENLY STARTED AND TRAMMED HIS FOOT.
EMPLOYEE STATED3HE WAS MOVING MINER CABLE OUT OF ROADWAY AND HURT HIS BACK.
EMPL HELPING PL5CE TIMBERS BETWEEN 2 STEEL ARCHES WHEN SEVERAL TIMBERS FELL STRIKING HIM ON NECK,SHOULDER,BACK.
UNINTENTIONAL R2OF FALL ON MAIN WEST BELT AT 6 CROSS CUT. NO MEN INVOLVED. COVERED THE MAIN WEST BELT.
UNINTENTIONAL R2OF FALL.#3 UNIT,#6 ENTRY,3 X-CUTS FROM FACE.NO MEN OR EQUIP INVOLVED.USING 6'POINT ANCHOR BOLTS AND T-TIMBERS.
EMPLOYEE STATED3HE WAS HELPING PULL BELT BACK TOGETHER TO PUT SPLICE IN BELT BELT RIPPED CAUSING TIE OFF BLOCK TO COME FORWARD AND HIT EMPLOYEE DISLOCATING LEFT ELBOW
EE STATED HE W5S POUTTING UP RAIL BARS WHEN HE HURT HIS BACK.
UNINTENTIONAL R2OF FALL ON #1 UNIT TRACK ENTRY,UST X-CUT OUTBY FACE.NO MEN OR EQUIPMENT INVOLVED.USING 48'' RESIN BOLTS AND X-BARS AND LEGS.
UNINTENTIONAL R2OF FALL SOUTHWEST MAIN TRACK ENTRY 2 X CUTS INBY SPAD 5014 NO MEN OR EQUIPMENT INVOLVED USING 4 FT R ESIN BOLTS CRIBS 7 RAIL BARS 6X6
EMPLOYEE WAS USING 20 TON JACK TO LIFT I BEAM I BEAM SLIPPED OFF JACK, HITTING EMPLOYEE IN FACE.
A dated report covering the 26-year penalty trail, line-item violation pattern, contest and docket posture, rate-normalized peer benchmark, and full fatality history. Delivered as a PDF with the underlying data as CSV.