St Marys Cement-Detroit Metal/Non-Metal

Notified that an incident occurred. Upon checking near the main shop area, Miner 1 (an electrician) was found lying on the main floor, surrounded by fellow miners. It was determined that the 440 main breaker had experienced a catastrophic failure. Subsequent observations revealed that Miner 1 had borne the brunt of the failure and sustained 2nd-degree burns to both hands.

Miner A was chipping debris in the discharge area of the finish mill, when Miner B noticed a fresh wound on Miner A's right forearm. It is believed that material from the mill caused this laceration. Miner A was conveyed to the hospital and released later that day. Miner A returned to work the next day.

Description of Incident: Employee was attempting to remove pallet from lowered hi-lo forks by hand and sustained a small laceration of left middle finger from an exposed packing nail. Employee was taken to ER and treatment was rendered in the form of two stiches. Employee was cleared and returned to work.

Employee was holding a hose and working with another employee to remove a fitting which was taped to the hose. The other employee was cutting the tape and hose when the knife slipped and struck the back of the employee's right middle finger causing a laceration. The laceration required sutures to close.

The employee went to put an air lance down the pipe, when doing so the air came back faster than expected and the material went right over safety glasses and into the employees eyes. The employee was not wearing EE's face shield.

Miner entered a confined space that shut down 8 hours before hand. The miners boots were not tied. 6" of hot material was at the bottom. The miner stepped into hot material. That material got into EE's boot and burned EE's foot. 2nd degree burn.

Using a crane and hopper to load balls into finish mill. An employee tried to connect the crane hook to the clevis. The operator lifted the load before employee was done attaching the hook.

Resting right foot outside of skid steer cab. Left foot hit controls moved bucket arm, slight crush foot.

Employee was putting away materials from shipment. Took empty boxes to trash bin and EE's back spasmed causing pain.

climbing out of bobcat and twisting.

EE was cleaning area for compressor to be installed and was struck by PVC pipe. EE said EE felt fine but wanted to get checked out. EE is on FMLA and usually takes 1-2 days off a week. EE was taken to emergency and was released without any restrictions. EE went to EE's FMLA doctor and asked for medication for the tightness and was given rest of week off.

Hot slag fell on EE's leg from export bin.

Employee walked from fuel pump to open door looking down on 9 tail pulley to check on water presence in tunnel. Employee turned to the right and walked away from chained doorway when right foot slipped on ice. Left leg bent underneath employee, left arm slipped out over employee's head trying to stop fall.

30 below freezing temperatures with icy walk ways. Employee was walking to work station when they slipped and fell on ice.

Employee was sweeping the Mill building floor with a broom and felt a sharp pain in lower back.

Employee was walking down a stairway at the Bulk Scales and slipped and fell down 4 or 5 steps. Stairway was clean, free of any trip hazards and well illuminated. The employee injured pelvis area.

Standard threshold shift resulting in a reportable hearing loss by miner.

Standard threshold shift resulting in a reportable hearing loss by miner

Standard threshold shift resulting in a reportable hearing loss by miner.

Standard Threshold shift resulting in a reportable hearing loss by miner.

Employee exited shower, while getting dressed, inadvertently kicked bench in locker room.

Standard threshold shift resulting in a reportable hearing loss by miner.

Standard threshold shift resulting in a reportable hearing loss was suffered by the miner. 2008

EE, a Thermico, Inc. was working as a contractor at the St. Mary's Cement plant in Charlevoix, MI and the clamps holding a 4-ft bar broke loose and fell 40 feet striking the employee in the right upper arm. He sufferer a fracture of his right upper arm and was treated at the local hospital.

Moving scrap steel from grounds to dispose of in scrap steel hopper. Awkwardly shaped section of purling struck employee in the thigh.

While using pry bar to unplug interchange, lost balance and fell backwards.

Employee was using a prybar to position a rubber pinch valve sleeve between 2 flanged pipes. His prybar slipped and hit his forehead.

EE was installing V belt over clinker dust collector fan driven pulley. While turning pulley to install belt, finger was pinched and amputated between V belt and pulley sheave.

A customer twisted his ankle.

Employee did not report injury until February 9, 2009. Employee was jackhammering between 2 mill pipe lines. Left foot slipped on loose material. He grabbed jackhammer, causing strain to hip.

While screenign balls, ball screener plugged up. EE climbed ladder stand and poked the chute to unplug the ball screener. The ladder stand collapsed, causing EE to fall.

Abandoned car noticed near stack around 1:30pm. Police were called-they stated its' an abandoned car and left. In the morning, smoke was coming from car. EE put out fire. Police were called again, they checked inside of car and found body of a man. Car and body were removed by Detroit Police around 10:30am

While making silo change tigtened pinch valve, fell pull on right groin side.

Rebuilding equipment-using chain falls and come-a-longs during which time felt sharp pain-pain went away but injury became progressively worse.

EE called to say he had been to his doctor and has carpel tunnel. EE believes condition is work related.

Getting out of forklift, got right foot caught in step area of forklift and twisted knee.**Injury reported to Co. 5-31-07 and Restricted Duty began 6-29-07.**

Opened inspection door on chute to remove chunks of material, got a face full of cement.

Working between stored pallets, hit elbow on metal framework.

EE was working under 3 scale trying to free up the load cell. He was trying to crawl under the bar and hit his knee on the bar.

Slipped on sidewalk outside Distribution building.

Employee picked up a chunk of material, dropped the chunk, it hit a shovel. The shovel handle popped up and hit employee in the left jaw.

Employee was working plate in Herzog. He tried to release stuck plate, cut hand on metal and burned left hand on flame.

Cleaning the 1/2 floor dryer. When he got up he hit his head on overhead beam.

Contractors were to install equipment. EE was to assist contractors. Contractor cut his hand causing load to shift to EE that was injured.

Employees were cleaning out a stone bin filled with hard limestone. Employee injured back when moving a jackhammer to a new location.

In the lunch room getting water when the lunch room door swung open and hit him in the head

EE OPENING PINCH VALVE ON SILO 19. VALVE HIT WRIST

Employee was swinging a sledge hammer when he felt a sharp pain in the right side of his back.

WHILE MOVING VACUUM HOSE, A BOBCAT OPERATOR MOVED BOBCAT AND SWUNG BOBCAT BUCKET INTO EMPLOYEE'S KNEE.

EE FELL BACKWARD ONTO ARM WHILE MAKING A SILO CHANGE, DOESN'T KNOW WHAT HE TRIPPED ON.

Operator was bent over sorting steel balls on the floor with other employees. Contractor working inside mill welding a plate dropped the plate; it fell through door in mill. Plate glanced off steel bolts striking employee in lower back. Plate fell 20 ft; it was 18" by 6" and 1/4" thick.

PACK HOUSE OPERATOR OPENED DOOR TO PACK HOUSE ELEVATOR AND FELL IN ELEVATOR WHICH WAS NOT ON THAT FLOOR. ELEVATOR HAS A 2ND GATE THAT NEEDS TO BE CLOSED BEFORE ELEVATOR WILL MOVE. WHEN ELEVATOR IS IN CORRECT POSITION IT IS LIT & THE ENTRANCE IS ALSO LIT. EE BACKED INTO ELEVATOR W/OUT LOOKING.

PUSHING BAGS ON PALLET LOADER EMPLOYEE'S LEGS FELL THROUGH TRACK.

WHILE UNRAVELING A TWISTED CABLE ON THE LOADER OPERATOR STEPPED BACK FALLING.

CONTRACTOR EMPLOYEE COMPLAINED OF BACK PAIN WHILE HANDLING WHEELBARROW OF GYPSUM. AFTER FIVE DAYS OFF WORK HIS EMPLOYER RE-ASSIGNED HIM TO ANOTHER COMPANY.

WHILE REMOVING BOLTS & NUTS ON LID TO SLAD SCREEN, CHANNEL LOCKS SLIPPED PINCHING FINGER.

WHILE APPLYING PRESSURE TO LOOSEN BOLT WITH SCREW DRIVER, THE SCREWDRIVER SLIPPED CUTTING EE'S THUMB.

WHILE REVIEWING INSPECTIONS SHEETS, DUST FROM PAPERWORK ENTERED EYE.

WHILE MOVING CABINETS, LOST BALANCE AND TWISTED KNEE. NOTE: ALL TREATMENT WAS FIRST-AID UNTIL 5/20/04 - NOW IS PHYSICAL THERAPY. 7/26/04: LOST TIME OCCURRED WHEN EE HAD SURGERY 7/7/04 FOR TORN LIGIMENTS. INJURED FIRST EXPERIENCED PAIN 5/3/04.

DURING SLUMP TEST, OPERATOR STOOD UP STRIKING HIS BACK ON A PULL OUT SHELF ON A NEAR BY DESK. OPERATOR HAD CONSIDERABLE PAIN BUT THOUGHT IT WOULD GO AWAY. OVER THE LAST FEW MONTHS THE PAIN HAS GOTTEN PROGRESSIVLY WORSE.

EE was driving van, it started sliding on wet pavement, when brakes were touched it slid into parking lot pole; cement dust and rain created slipery conditions.

EE WAS TO TIGHTEN SCREW IN MCC CIRCUIT BREAKER AND TOUCHED GROUNDED METAL POST AND GENERATED AN ELECTRIC ARC. EE WAS NOT WEARING GLOVES, SAFETY GLASSES, DID NOT REMOVE CASING, AND USED AN UNINSULATED SCREW DRIVER.

WHILE OPERATING BOBCAT AND DUMPING LOADED BUCKET, DUST BLEW BACK INTO EE'S EYE.

CARPAL TUNNEL SYNDROME DUE TO DATE ENTRY.

EE WAS LEANING INTO MACHINE TO CLEAN IT, ANOTHER EE HIT START BUTTON, PINCHING EE'S THUMB IN THE MACHINE.

EMPLOYEE PULLED MUSCLE IN ARM WHILE PICKING UP A HEAVY BUCKET.

EMPLOYEE TRIED LOOSENING A TIGHT VALVE & PULLED A MUSCLE IN HIS BACK.

WENT TO CONDUCT REPAIR AT FK PUM BY MILL & WHILE STANDING ON CONCRETE BASE, EMPLOYEE REACHED FOR PRESSURE SWITCH & TWISTED RIGHT KNEE.

EMPLOYEE HAD SAFETY GLASSES ON & WALKED INTO THE OIL HOUSE; SOMETHING BLEW INTO HIS EYE.

AS EMPLOYEE GOT OUT OF THE FRONT END LOADER, SHE TWISTED HER ANKLE.

EMPLOYEE GOT HIS BOOT CAUGHT IN THE RAILROAD TRACK AND FELL, STRAINING HIS LEFT KNEE.

ACCIDENTALLY SMACKED RIGHT HAND AGAINST COOLER.

LEG CRAMPS FROM PROLONGED STANDING.

WHILE PUSHING A HOIST ONTO A PALLET, HE PULLED A BACK MUSCLE.

WHILE LIFTING ELECTRICAL EQUIPMENT EMPLOYEE FELT A PULL FROM HIS LEG TO HIS STOMACH.

WHILE TRYING TO PUT FIRE OUT ON THE GRASS, EMPLOYEE TWISTED ANKLE.

SHOVELING IN THE TRANSFER TOWER, HE PULLED A MUSCLE.

EMPLOYEE TURNED AND REACHED TO PICK UP A CEMENT BAG TO PLACE ON THE PACKER: ROTARY CUFF IS SORE.

ATTEMPTED TO PULL A JAMMED CEMENT BAG FROM THE A-LINE.

EMPLOYEE WAS LIFTING A GEAR BOX & HURT HIS BACK.

CEMENT DUST GOT INTO RIGHT EYE.

A PIECE OF CEMENT WAS ON A CABLE CORD ON A SHELF AND WHEN PULLING THE CABLE OFF THE SHELF CEMENT WENT INTO THE EYE.

WHILE MAKING A LIFT, THE WIRE CHOKE ATTACHED TO THE HOIST BROKE. A PIECE OF ROUND STOCK THEN FELL UPON AN EE'S FOOT. THE EE'S RT. FOOT WAS BROKEN.

HURT BACK FROM REMOVING AND REPLACING A DAMAGED BAG.

EE WAS MOVING A NEW FILE CABINET, 4 DRAWER, AND STRAINED HIS BACK.

GETTING OFF THE FRONT END LOADER, HE TWISTED HIS ANKLE.

ATTEMPTING TO GET INTO DUST COLLECTOR, THE LADDER MOVED, HE ATTEMPTED TO CATCH HIMSELF, INJURED HIS SHOULDER.

THE CRANE CABLE BROKE.

ALLEGEDLY LIFTING A TABLE, THE EE STRAINED BACK.

OPERATING A JACKHAMMER AND DUMPING WHEELBARROW WITH CLINKER, HE DEVELOPED A HERNIA.

LIFTING A BUCKET OF CONCRETE.

THE EMPLOYEE WAS CLEANING #11 SCREW WHEN HE DISCOVERED THE SCREW WAS NOT RUNNING. HE ATTEMPTED TO GET THE BELT STARTED AND FAILED TO TURN SWITCH OFF.

SHOVELING,FELT PAIN IN GROIN AREA.

CLEANING UNDER THE CONVEYOR BELT,HE STRAINED HIS BACK WHILE SHOVELING.

REPAIR COMNPRESSOR OF INSULFLATION DUST.

WHILE JACKHAMMERING HE FELT PAIN IN H IS BACK

ALLEGES WHILE JACKHAMMERING AROUND CEMENT COOLER.

USING A PRY BAR TO TRY TO PLACE FRAMWORK ON BALL DUMPER IN PLACE; THE BAR SLIPPED AND JERKED EMPLOYEES SHOULDER.

ATTEMPTING TO CLOSE WINDOWS TO PREVENT DUST COMING IN. IT FELL ON HIS FINGERS.

WHILE GETING OFF PAYLOADER, HE STRUCK HIS LEG ON THE LADDER OF EQUIPMENT.

BURNING A BEARING OUT OF A ROTARY FEEDER, A PIECE OF SLAG BURNED ELBOW.

EMPLOYEE STATES THAT WHILE ATTEMPTING TO PULL A PIPE OUT OF WATER SPRAY ON #3 MILL, HE STRAINED BACK.

CHANGING #2 SEPEERATOR BLADES, HE WAS IN A CONFINED AREA.

WHILE LIFTING BEARING, HE INJURED BACK.

WORKING IN REAR OF #3 MILL WITH WELDING ROD AND SOME SLAG CAUSED CAN OF AERO KROIL TO EXPLODE CAUSING BURNS ON HIS BODY.

WAS CARRYING OIL IN 15 GALLONG CAN TO MOTOR DS #3 FROM GARAGE.

HE WAS TAKING A DOOR OFF AND HIT HIS LEFT THUMB WITH A HAMMER. HIS RIGHT ARM IS ALSO BOTHERING HIM.

BURNING ON TEH DIVISION HEAD OF #2 FINISH MILL, THE TORCH SET HIS GLVOE ON FIRE.

WAS WORKING IN #2 FINISH MILL AND A PIECE OF THE DIVISION HEAD FELL ON HIS LEFT THUMB.

WAS IN #3 BUCKET ELEVATOR-STRAPS ON BOLSON CHAIR BROKE.

WHILE WORKING, "A 2 X 4 X 6 INCH PIECE OF STEEL SHOT OUT AND HIT HIS LEFT FOREARM.

WAS GETTING OFF THE BOBCAT AND FELL BETWEEN ANOTHER PARKED BOBCAT CAUSING CONTUSION TO LEGS.

WAS EATING LUNCH AND HE GOT A PAIN IN HIS CHEST.

WAS TRYING TO LIFT A BAR WHICH WAS STUCK AND HE PULLED RIGHT GROIN. THERE WAS A BURNING SENSATION.

WAS WORKING ON A HEAD SPROCKET, WITH A HAMMER AND HE SLIPPED AND WACKED HIS LEFT THUMB.

WAS LIFTING AND HE FELT A SHARP PAIN IN HIS CHEST.

CHANING FLOP GATE GATE JAMMED AND INJURY OCCURRED.

PUTTING IN SKIRTING BACK STARTED TO HURT.

WAS RUNNING A JACKHAMMER AND JAMMED HIS RIGHT HAND AND FOREARM.

DROPPED KILN FEED PIPE ON FOOT.

WAS HUNGING CHAIN STEPPED UP TO PASS TO ANOTHER EE AND TWISTED RIGHT KNEE.

WORKING ON THE CONVEYOR-WIND BLEW DUST/DIRT IN EYE.

SHOE WAS HUNG UPON SOME GRATING & HE WENT TO MOVE BUT LEFT LEG WAS STUCK & TWISTED HIS LEFT KNEE

WAS USING PALLETIZER MACHINE & THERE WAS MALFUNCTION OF MACHINE TRAP DOOR CLOSED ON ARM.

WAS GRINDING INSIDE A CONE. A MAN OUTSIDE WAS WELDING AND A SPARK FLEW AND CAUGHT THE BACK OF HIS SHIRT BURNING HIS BACK.

GOT THUMB (LEFT) SMASHED BY A COME-A-LONG.

DROPPED STEEL PLATE ON RIGHT INDEX FINGER FX.

PICKED UP MOTOR & PULLED MUSCLE IN LOWER BACK.

I WAS WALKING DOWN STAIRS AND FELL ON MY RT SIDE AND LOWER BACK

I WAS OPERATING A 65 LB JACKHAMMER AND I TWISTED MY LEFT WRIST

I WAS BURNING WITH A WELDER WHEN SOME OF THE HOT SLAG FELL ONTO MY RIGHT ARM AND HAND.

"I WAS COMING UP A FLIGHT OF STAIRS, STEPPED ON A SMALL ROCK AND TWISTED MY RIGHT ANKLE. I BROKE THE SAME ANKLE ABOUT 2 1/2 YEARS AGO.

WHILE LIFTING A PIECE OF STEEL IN THE PRECIPTATOR BLDG.HE FELT SEVERE APIN IN HIS CHEST.

I GOT MY RT.HAND PINNED IN BETWEEN A SPEED R EDUCER & THE WALL

I WAS CLEANING OUT THE CLAY MILL TANK & W AS THR*OWING OUT BOLDERS & MY LOWER BACK STARTED HURTING AGAIN

SLIPPED ON HOSE NEAR MILL AT BRENNAN AND HURT BACK.

I FELL 6FT.& LANDED ON MY TAIL BONE & TWISTED MY LEFT ANKLE

HE WAS KNEELING ON SOME SCAFFOLDING & WHEN HE GOT UP HIS LOWER BACK DEVELOPED A SEVERE PAIN

INJURED ARM WHI5E LIFTING LINER PLATES

HE WAS REMOVING3IMPELLER FROM #3 UNDERFLOW PUMP & IN SO DING HE PULLED A MUSCLE IN HIS LOWER BACK

HE WAS SWINGING A SLEDGE HAMMER & HE H IT HIS H AND ON THE SIDE OF A PALLET

USING JACKHAMME9 WHILE LYING DOWN CLEANING UNDER #11 BELT EMPLOYEE INJURED HISBACK

WHILE HOEING AN8 SHOVELING SOME CLINKER DUST MY LOWER BACK STARTED HURTING.

EMPLOYEE WAS HI7 WITH BRICK IN THE KILN INJURING HIS UPPER BACK AND LEFT SHOULDER

TRYING TO OPEN 8OOR TO THE CLAY PUMP ROOM THE EMPLOYEE INJURED HIS BACK BECAUSE THE DOOR WAS JAMMED

BASE OF LADDER 2FF FROM HOT INSULFLATION DUST CAUSING EMPLOYEE TO SLIP AND BURN HIS WRIST

EMPLOYEE WAS LI1HTING A TORCH AND A FLAME CAME OUT AND BURNED HIS LOWER ABDOMEN.

HE WAS ON TOP O0 THIS MILL AND THERE WAS A LOT OF GREASE UP THERE AND HE SLIPPED AND CAUGHT HIMSELF AS HE WAS SLIPPING, AND HIS RIGHT LOWER BACK "POPPED".

WHILE OPERATING3BOBCAT RAN OVER A BIG HUMP WHICH CAUSED BOBCAT TO JUMP UP OFF THE GROUND THROWING HIM OUT OF SEAT AND INJURING HIS LEFT SIDE AND HIP.

EMPLOYEE STATES3THAT WHILE SHOVELING DIRT MY LOWER BACK BEGAN HURTING.

HE SLIPPED ON S2ME WATER AND JAMMED HIS LITTLE TOE ON HIS LEFT FOOT UNDER A LOCKER.

EMPLOYEE DISCOV9RED THAT TGHERE WAS A LEAK IN AIR CYLINDER GOT A REPAIRMAN IN ATTEMPTING TO SHOW THE REPAIRMAN WHERE THE LEAK WAS HE POINTED HIS FINGER IN THE CYLINDER WHIULE THE PACKER WAS P LACING A BAG ON3THE SPOUT

PATIENT STATES 4HILE AT WORK, I SLID DOWN A GREASY LADDER, LANDED ON THE GROUND (CONCRETE) FLAT ON BOTH FET AND HURT BOTH MY KNEES

HE STATES THAT 4HILE AT WORK, HE SPILLED ALKALINE WATER ON HIS FOOT BURNING IT.

WHILE LOWERING 8CRAP TO THE FLOOR FROM SEPERATOR, FINGERS BECAME LODGED IN CRANE CABLE.

THE PORTA-PAK H9 WAS WORKING ON AT #2 AGITATOR SLIPPED HE HIT HIS THUMB CAUSING A CUT AND SOME SWELLING.

LIFTING A 400LB8. BARREL USING HOIST,DRUM SWUNG AROUND AND HIT HIM IN THE CHEST.

SHOVELING UNDER3#8 BELT,HE FELT PAIN IN HIS LOWER BACK.

STANDING ON A 5ADDER WHILE ATTEMPTING TO TAKE THE WEDGE OUT OF CABLE AND REWIND IT, THE LADDER WAS CAUGHT IN THE COUNTER WEIGHT.

REPAIRING THE D3SCHARGE PUMP, HE ATTEMPTED TO CLOSE A VALVE AND INJURED HIS BACK.

WALKING ON TOP 2F #2 MILL HE TRIPPED ON OXYGEN AND ACETYLENE LINES.

OPERATING AN AI9 HOSE SHE STARTING HAVING PAINS IN HER CHEST.

WALKING TO THE 9ESTROOM HE SLIPPED ON WET PAVEMENT AND INJURED HIS KNEE.

WORKING ON THE 9AW MILL FEED BELT, SHOVELING STONE THAT WAS WET

TAKING A 70 LB 4ACKHAMMER OUT OF THE LEACH TANK BY CARRYING IT DOWN A LADDER

OPERATING AN EN8LOADER HE HIT AN AREA IN THE FLOOR THAT WAS UNEVEN AND INJURED HIS HAND WHEN IT WAS CAUGHT IN THE STEERING WHEEL

SLIPPED OFF STE1 OF CRFANE WHILE GETTING OFF

WORKING ON #12 1RECEPITATOR SCREW HE ATTEMPTED TO MOVE A MOTOR & INJURED HIS BACK.

SLIPPED OFF THE3BOARD INTO HOT DUST.

WORKING IN THE 1RECIPITATOR ON #8 SCREW, USING THE LADDER TO STEP ON HIS FOOT SLIPPED AND HOT DUST BURNED LEG.

WALKING THROUGH3THE MILL BUILDING A DRAIN COVER SLIPPED AS HE STEPPED ON IT CAUSING HIS FOOT TO SLIP INTO THE DRAIN.

PAIN IN ARM AND3SHOULDER AFTER ATTEMPTING TO PULL WEEDS OUT OF ELECTRICAL AREA.

WHILE ATTEMPTIN1 TO BACK OUT OF THE KILN THE GUARD OF THE BRICK PEELER HIT THE TOP OF THE BURNER PIPE CAUSING IT TO PIN THE EMPLOYEE BETWEEN THE STEERING WHEEL AND THE SEAT.

WHILE ATTEMPTIN1 TO UNPLUG #2 MILL DUST COLLECTOR HE HIT HIS HEASD ON AN OVERHEAD SCREW CAUSINGINJURY TO HIS NECK

SQUATTING DOWN 9EPAIRING 3 DUST COLLECTOR.

A PIECE OF STEE5, 2X2FT ANGLE IRON FELL ON HIS FXX HAND CAUSING INJURY TO HIS MIDDLE FINGER.

EE JUMPED OFF T2E DRAG CHAIN & LANDED ON HIS HEEL CAUSING A CONTUSION.

WELDING GRATES 2N BOTTOM OF COOLER GRATES.

THE EMPLOYEE WA8 ATTEMPTING TO GET A BROKEN LOG OF CEMENT OUT OF THE HOPPER.

DUMPING WHEELBA9ROW TO CHUTE ATTEMPTED TO DUMP WHEEL BARROW IT TIPPED FORWARD,PULLED HIS SHOULDER.

WHILE WORKING H9 CAUGHT HIS LEFT RING FINGER BETWEEN A LADDER

LIFTING A TIPPI3G VALVE HE INJURED HIS LOWER BACK

CLIMBING DOWN L5DDER FROM #3 AIR SLIDE HE STEPPED IN GREASE AND FELL

WALKING UNDER A3STEEL FRAME SUPPORT HE HIT HIS HEAD ON A STEEL FRAME.

CLEANING SPILLS3ON THE FEED FLOOR HE SLIPPED ON MUD CAUSING INJURY TO HIS BACK.

MOVING A WHEEL 6ARROW OF MUD HE STRAINED ABDOMINAL WALL

THE AREA WAS WE7 MUCCY AND COLD

WORKING IN KILN3HANGING CHAINS

WALIKING NEAR T2E BULK SILOS SLIPPED ON ICE

EMPLOYEE WALKIN1 IN MILL TRIPPED OVER COVER PLATE ON FLOOR

MOVING COAL MIL5 ROLL FROM SHOP TO THE COAL MILL USING A FORK TRUCK

OPERATING A JAC5 HAMMER.

OPERATING THE B9ICK PEELER TO REMOVE COATING FROM THE KILN.

CHANGING A DRAI3 PIPE HE STRAINED HIS SHOULDER.

WHILE WORKING IN #3 SEPARATOR HE FELT PAIN IN THE LEFT GROIN.

EMPLOYEE WAS CUTTING OUT A SECTION OF STEEL FROM CONVEYOR WHEN THE CUT SECTION FELL ON HIS TOE

GUIDING BUCKETS OF MILL BALLS TO HOOK TO CRANE HE INJURED HIS BACK.

CONFLICTING REPORTS OF HOW INJURY OCCURRED.

HITTING INSULATION ELEVATOR WITH A 5 INCH