Amrize Three Rivers Quarry Metal/Non-Metal

While offloading material from a haul truck, a hydraulic cylinder broke, causing the bed to fall unexpectedly. The employee suffered a strained neck and was initially treated with First Aid. After five days, they sought medical attention, were diagnosed with an irritated nerve, and returned to work with restrictions.

Employee was removing screens (est. weight of approximately 70 lbs each) from the manlift when the screens began to slide. While attempting to prevent them from falling, the screens slid across the employee's wrist, causing a laceration that required 8 stitches. The employee was returned to work with medical restrictions

While dismounting from the driver's side of a water truck, the employee missed the bottom step and fell backward, landing on their backside. Initial injuries included a scrape to the arm and leg and back soreness (first aid). On 2/11, they reported neck stiffness, received medication, and were recommended physical therapy starting 2/21. Work status: No restrictions.

Employee was riding in a side by side utility vehicle that flipped over on its side and EE sustained an injury to their right knee. EE was wearing the seat belt at the time of the incident

Employee struck their left thumb with a hammer while tightening a bolt with a slug wrench.

The employee was washing at the plant station with a 1.5" water hose when the employee's left forearm began to swell. Due to a pre-existing personal injury, they had recently been released to full duty.

Employee was helping a customer hook up a water hose on the water truck and their shoulder began hurting. Employee did first aid. Employee was then seen at a clinic. F/U to clinic employee was given orders to start physical therapy on 7/30/24.

Bolt broke on motor causing it to fall onto employees left arm.

While exiting the LD11 (980k) loader employee missed a step and fell to the ground no more than 4ft.

Employee stated they were using 3 points of contact while descending the engine access ladder when they lost footing and fell aprox. 3' to the ground injuring left leg, knee and ankle.

A 777 haul truck was getting loaded by a 992 loader when a rock hit the bed hard enough to make the driver bite their tongue and pop their back.

Employee alleges to being bent over using water hose to clean beneath CV46 when felt sharp pain to lower back.

Employee was working on One Jaw Crusher when the left hand was pinched by the shims. This resulted in two broken fingers and required surgery.

(First aid) Employee misplaced their footing and fell while reaching above their head for bolts. 4/21/2021 Became medical due to starting prescription medication.

Laying on right side extended right arm holding end of return roller, pulled roller up towards body and injured bicep.

While loading haul truck boulder caused rocking motion of truck, resulting in restricted duty injury to the haul truck driver.

Employee was walking in the plant and twisted the left knee.

Lifting tool box (40 pounds) - modified work days injury to back

Employee struck chin against handrail resulting in a laceration to the chin.

EE was changing out roller cans on CV-23. EE bent over to be able to get between the belt and the roller and was extended to the other side of the conveyor frame. When trying to grab the roller can it was still stuck. When it finally broke loose and the weight of the can transferred to the injured employee's arms, pain was felt in the groin area.

Employee was dismounting a Komatsu loader - stepped on a rock and twisted an ankle.

The employee was changing screens on the plant and suffered a burn to the top of employee's right hand.

As injured employee was walking EE wasn't watching EE was going and EE's knee bumped the sledge hammer handle that EE had previously placed on the floor adjacent to the track mobile. The injured employee grabbed for the hammer handle to prevent it from falling to the floor and the same time the right ankle turned inward.

Employee was removing rock from a spill from a plugged chute when chute was free a rock rolled off from the chute hitting employee in the top of the hard hat. It became a lost time on Aug 16, 2016

EE was working outside using a 20lb sledge hammer to loosen material that was stuck inside the chute. EE went in to cool off. About 10 minutes after EE tried calling to get ahold of someone because EE stated was cramping up and skin was hot clammy and EE was shivering.

Employee put boots on in morning noticed bug bite at the end of the day at home.

Employee handling an approximately 50 lb. rock sample in a 5 gallon bucket - Employee set the sample down on the floor and said his back was hurting.

Employee was underneath a truck making repairs and his hard hat fell off - when employee reached to retrieve his hard hat he bumped his head, causing a small laceration to his head.

Employee using a 2" water hose - Pulled hose to remove a kink from it and the released energy from the hose knocked employee off balance causing her to fall.

Employee picked up a pail containing a rock sample and strained his back.

Employee was grinding on a crusher liner and some debris flew into his eye.

While investigating a problem with the pit belt beneath the 1 Jaw Crusher, employee tripped over a rock and fell to the ground.

While operating a loader employee felt pain in right groin area.

Employee slipped on ice in the parking lot and fell on elbows and back - Received a fracture to right clavicle bone.

Employee was loosing a coupling on a water hose and the wrench slipped striking the employee in the mouth, chipping a tooth.

Employee was walking on uneven surface to his vehicle, when he stepped on a rock and turned/sprained right ankle.

Employee was standing on dozer track, fueling dozer - Hand slipped from grab rail, employee fell backwards to the ground, bruising right heel.

Employee stepped from barge to the dock - twisting his knee.

Employee was pulling on a hose when his foot got caught on another hose on the ground. Employee tripped and landed on hands, resulting in a broken right wrist.

While installing liner in chute employee strained lower back.

Employee was installing idlers and strained left shoulder.

Employee sustained a metal splinter in right hand above thumb knuckle. Became reportable 7/26/2012.

Employee was pulling cable out of water and strained back.

Employee stepped on a rock and twisted right knee.

An Employee was attempting to remove a 36lb submersible pump from a hatch on the upper dock. As the employee was pulling the pump up, it hung on a ladder rung. The employee pulled on the pump a couple of times to try and force the pump loose, which caused the employee to have a back strain.

An Employee was starting mobile equipment on the ready line. After starting the first 992G loader he suffered a heart attack.

An Employee was repairing a hydraulic pump. Once it was repaired, the employee picked up the hydraulic pump to put it in place. Two days later the employee reported his upper back was hurting from lifting the pump.

Employee was prying snap deck panel loose from the screen with a screw driver. The screw driver slipped and struck him just above the left eyelid, making a small cut above left eye. The employee was wearing the required eye protection at the time of the incident.

Employee was operating a man-lift when he drove over a rock causing the employee to loose his balance. The employee hit his shoulder on the handrail resulting in a contusion. Reported on 8/21/2009, became reportable on 4/9/2010 when the doctor took him off of work.

Employee was standing under conveyor attaching a nylon sling to the belt that was tangled around the framework of the take up pulley. A piece of material fell from the framework of the conveyor and struck them in the back of the hardhat.

Employee was loading rollers into the back of a pick up. While loading he struck the tail gate post that locks the tail gate in the closed position with his left pinkie finger causing a laceration.

Employee was walking down 5-dock ramp to boat, when he stepped on a patch of ice, causing him to fall onto his right hand and forearm.

Employee was walking between MCC5 and LPT system water tanks when he stepped into a hole full of slurry. At the time of the incident he did not think he had an injury. Reported to company as injury on 10/23/07, doctor released to full duty at that time, became reportable when doctor took him off work on 11/13/07.

Employee was standing on rope stand platform, throwing a swing line rope to another employee. His left foot slipped off the platform, onto the first step, twisting his back.

Employee was climbing into grader. He placed his right hand on the door frame and was inspecting the grease on the table when the wind blew the door shut on his right hand.

Employee was attemting to clean Ultrasonic at the 7 ft. cone crusher. His right middle finger was caugh between a bolt and the motion sensor, causing a laceration.

Employee was climbing ladder to haul truck and felt a sharp pain in his lower back. Delay in reporting due to misdiagnosis by doctor. Doctor stated the pain was caused by a fractured vertebrae from a fall. The employee had not fallen and went for a second opinion where a pinched nerve consistent with the activity was diagnosed making the injury reportable.

Employee was unhooking the haul cable from a loaded barge, when the cable was unhooked and the winch operator began to raise the cable the cable hung under the cavel. When the cable became tight it sprang from under the cavel and struck the employee in the left thigh.

Moving pipe threader, felt pain in knee.

Carrying load down steps, when knee popped, causing pain in right knee. This was 1st aid until 5-16-06 when EE wanted to have DR. check it. This company was notified of this on 5-16-06.

EE was checking work at area #46 conveyor hand rails and walk ways when a section of grating measuring 24 1/2 x 67' fell through after apparently slipping out of place. This resulted in a fall of 15'3" to ground.

Employee fell from scaffolding during dismantling process.

Slipped on welding blanket in screen, extended body to catch fall, struck back of neck on beam above.

Co-worker pushed concrete chute striking employee on the opposite side of chute causing him to fall off 4' high pier. Employee worked until Jan. 16, 2006. Began missing work on Jan. 17, 2006.

Employee was pulling extension cord while grinding and tripped over the cord and fell.

While using handheld rock drill, at chest height, the bit broke. Drill fell to the ground & EE hit his right elbow on top of broken drill steel in the rock. The skin was not broken & EE only reported his elbow was "sore". EE worked without interruption for more than 2 months. Later the EE had swelling around the area and went to Doctor's office.

Changing screen cloth on the middle deck of the station 3 Diester. Employee laid a chipping hammer on the deck in front of him. Another employee then slid the screen cloth down to him so it could be put in place. The screen hit the chipping hammer and it popped up hitting employee in the forehead.

Two men, Other ee and EE were picking up rebar to stand up vertical got out of baance and fell back.

Employee was working on a screen deck in the tower of the #1 plant. His right hand started to itch, he thought it may have been a mosquito bite but it later began to swell.

Employee was being lowered in manbasket. Basket stopped suddenly. Employee was standing with legs crossed lighting a cigarette when basket stopped causing him to fall in squatted position. Knee struck basket interior causing injury.

Employee was using a utility knife to cut the end of a fire hose and the knife slipped cutting his right index finger.

Employee was checking a flex conduit at 2 jaw. He had his hand on a beam and a rock fell from above. The rock hit his left index finger causings a cut.

Employee was climbing access ladder on a WA800 front end loader when he fell to the ground. Employee right foot slipped on second rung from cab platform and he lost his grip with right hand. He swung out to the left while left foot and left hand still on loader when he lost his grip and fell an estimated 8.5 feet to the ground landing on his right side.

Employee was turning the water on at the water stand pipe so he could wash the bed of the truck bed. When he bent over to turn the water valve on there was an aluminum valve wrench hanging over head approximately six foot off the ground. The wrench fell striking the employee's hardhat and back of his head.

Employee was loading scrap metal on trailer. Had just loaded a 10" steel pipe with boom truck and disconnected lifting cable. Employee was concerned that pipe might shift during transport and roll off trailer. Employee repositioned pipe and mashed his right ring finger.

Ee was performing work on the crane on the lower dock. He and a co-worker were changing over from the claw to the bucket. After attaching the tagline to the bucket, ee tugged on the tagline to tension it up with the boom. The resulting tension sucked his hand into the cable guide (bell), and cut his hand.

Employee was replacing the drill steel in the drill and the end of one drill steel rolled over the top of his foot.

Employee was stepping over a water line that was approximately 4" off the ground. Employee's right foot caught on the water line and he stumbled and while trying to catch himself with his left foot, he sprained his left ankle.

EE WAS SHOVELING UNDER THE TAIL PULLEY OF THE CONVEYER AND STRAINED HIS LOWER BACK. THIS DID NOT BECOME REPORTABLE UNTIL 10-24-03.

EE WAS CONDUCTING HIS WORK AS A DECKHAND WHEN HEWAS STUNG BY A WASP.

EMPLOYEE WAS OPERATING A WATER TRUCK AND WHILE DRIVING THE TRUCK OVER A PERIOD OF TIMME HIS LOWER BACK AND LEG BEGAN TO HURT. THIS DID NOT BECOME REPORTABLE UNTIL AUGUST 4, 2003.

EE WAS USING A STEAM CLEANER TO CLEAN DRILL. HE TURNED TO THE LEFT TO PULL SOME SLACK IN THE HOSE. WHEN HE TURNED AROUND, THE END OF THE NOZZLE PASSED OVER THE TOP OF HIS FOOT. THE WATER PRESS URE CUT A HOLE IN THE TOP OF HIS BOOT, & THE HOT WATER BURNED THE TOP OF HIS FOOT.

EE WAS ASSISTING THE MECHANIC INSTALL A DRIVELINE IN A 100 TON HAUL TRUCK. WHILE INSTALLING THE DRIVELINE EE STRAINED HIS BACK.

EMPLOYEE WAS STEPPING OUT OF WORK BASKET OF BOOM TRUCK AND TWISTED HIS LEFT KNEE WHEN HIS FOOT CAME IN CONTACT WITH THE GROUND. *DID NOT BECOME REPORTABLE TILL 02/24/03.

EE WAS WASHING DOWN A CRUSHING PLANT & HIS LEG STARTED BURNING & HURTING. WHEN HE GOT HOME HIS LEG WAS RED & HE HAD A BROWN SPOT ON IT. HE WENT TO THE EMERGENCY ROOM & WAS TOLD THAT HE HAD BEE N BITTEN BY A SPIDER.

EE WAS WASHING WITH A 1 1/2" WATER HOSE, AND HITA PILE OF ROCK WITH THE STREAM OF WATER, AND THEOVERSPRAY WASHED DEBRIS OVER HIS SAFETY GLASSES AND INTO HIS EYE.

EE WAS REMOVING THE AUGER @ LIME MILL. THE BOOM TRUCK WAS ATTACHED TO AUGER TO LIFT WITH. THEY ATTACHED A COMEALONG TO ONE END OF AUGER TO PULL WITH. EE REACHED TO MOVE THE CHAIN ON COMEALONG & AUGER SLIPPED STRIKING HIS ARM.

EE WAS DRIVING A TRUCK & THE BEADED SEAT COVER KEPT PRESSING AGAINST THE KILL SWITCH BEHIND THESEAT. HE REACHED BEHIND THE SEAT TO CLEAR THE SWITCH & ACCIDENTLY STUCK MIDDLE FINGER ON RT. HAND IN FAN RESULTING IN 12 STITCHES TO FINGER. PUT ON ANTIBIOTICS FOR INFECTION & PAIN RELIEVER(UNABLE TO WORK FOR 2 WEEKS).

EE WAS PUTTING A HYDRAULIC PUMP ON MICHIGAN LOADER WHEN HIS WRENCH SLIPPED OFF BOLT, RESULTING IN HITTING HIS LEFT ELBOW, BRUISING MUSCLE. DR. PUT ARM IN SLING FOR 2 DAYS AND GAVE AND ANTI-INF LAMMATORY DRUG.

EE WAS WORKING IN THE BACK OF THE MAINTENANCE SHOP, IT WAS VERY WINDY CONDITIONS, AND THE WIND BLEW A FOREIGN BODY INTO HIS EYE. HE HAD HIS SAFETY GLASSES ON.

EE WAS USING THE AIR HOSE TO CLEAN OUT THE DUST BOX. THE HOSE SLIPPED FROM HIS HAND AND HIT HIM ON THE LEFT EYE.

EE WAS HELPING REPAIR THE LIME MILL AND STRAINED HIS BACK.

EMPLOYEE WAS GETTING OUT OF THE CRANE, HIS FOOT SLIPPED AND HE FELL, LANDING ON HIS RIGHT SIDE.

EMPLOYEE WAS DISMOUNTING OFF OF A FRONT-END LOADER AND HE STEPPED ON A ROCK, TWISTING HIS ANKLE.

EE JUST COMPLETED CHANGING THE AIR FILTER ON THELOADER AND WAS DISMOUNTING IT. WHILE DISMOUNTINGFROM THE LOADER HE BUMPED HIS LEFT ELBOW & ARM. THIS INJURY DID NOT BECOM REPORTABLE UNTIL 5/11.

TOOK LOADER INTO THE AREA OF THE SHOT ROCK TO GET A BUCKET OF ROCK TO LOAD A TRUCK. THERE WERE A LOT OF LARGE ROCKS AND THE LOADER HIT A ROCK AND STOPPED WHICH RESULTED IN A TORN MUSCLE AND PU LLED LIGAMENTS BY TWISTING HIS RIGHT SHOULDER.

EMPLOYEE WAS CLIMBING DOWN THE LADDER OF THE CAT773B HAUL TRUCK. HE STEPPED OFF OF THE LADDER ONTO A ROCK. HE TWISTED HIS ANKLE AS A RESULT OF STEPPING ON THE ROCK.

SECOND SHIFT FOREMAN WAS CLEARING & INSPECTING BELT. HE FELL OFF THE BELT & INJURED HIS NECK, SHOULDER, BACK, HIPS & LEGS. HIS RIGHT ANKLE IS SWOLLEN & HE HAS NUMBNESS IN HIS THUMBS. HE CONTIN UED TO WORK UNTIL 4 AM AFTER THE INCIDENT BEFORE HE LEFT WORK TO GO HOME.

TWO EMPLOYEES WERE CUTTING A ROPE USING UTILITY KNIFE, ONE WAS HOLDING THE ROPE TIGHT, WHILE THE OTHER CUT IT. THE KNIFE SLIPPED CUTTING THE EMPLOYEE HOLDING THE ROPE ON THE ARM. THE CUT RE QUIRED STITCHES TO CLOSE THE WOUND.

EE WAS STANDING BY A BOOM TRUCK WHEN THE OUTRIGGER WAS LOWERED ON HIS FOOT.

CUTTING HAND RAILS OFF IMPACT STAND, FELL THORUGH OPENING WHERE IMPACT SITTING. CUT LEFT ELBOW AND RIGHT KNEE. RIGHT KNEE SWELLED UP FRI. NIGHT SAID HE DID NOT NEED TO GO TO DR WOULD GO IF IT STARTED BOTHERING HIM. HE WAS LET GO 9-19 STILL IN PROBATIONARY/TRAIL PERIOD. HE THEN DECIDED HE NEEDED TO SEE A DR.

EMPLOYEE WAS GETTING OUT OF HIS TRUCK & TWISTED HIS RIGHT ANKLE.

EE PUTTING TOOLS IN TOOL BOX OF TRUCK. LID FELL ON LEFT ELBOW. EE DROVE HIMSELF TO HOSPITAL X RAYS ICE AND PAIN MEDS. NOT BROKEN, POSSIBLY CHIPPED. WATCH IT AND BE CAREFUL A FEW DAYS.

ON 4/22/00 THE EE FELL WHILE CLIMBING DOWN FROM A TRUCK AND LANDED ON HIS TAILBONE. THE EE WAS CHECKED BY A DR AND RELEASED TO NORMAL WORK. THE EE DID NOT SEEM TO GET BETTER AND ON 9/14/00 THE DR RECOMMENDED STEROID INJECTIONS, MAKING HIS INJURY REPORTABLE.

THE EE WAS CARRYING A RETURN ROLLER WITH ANOTHER EE. THE ROLLER SLIPPED OUT OF THE EE'S HAND CAUSING HIM TO STRAIN HIS RIGHT ARM AND SHOULDER.

WHILE OPERATING A HAUL TRUCK THE EE HIT A HOLE IN THE HAUL ROAD. HE WAS JARRED IN THE CAB CAUSING HIM TO HAVE A HEADACHE.

UNHANGING ROCK IN JAW WITH PRY BAR. DROPPED PRYBAR. WHEN PICKING UP PRY BAR, CAUGHT HAND BETWEEN BAR AND METAL WALL. BROKE MIDDLE FINGER ON RT HAND AT JOINT. WENT TO ER AT LIVINGSTON COUNTY HO SPITAL. FINGER PLACED IN SPLINT.

EMPLOYEE WAS ATTEMPTING TO THROW A HEAVY ROCK OUT OF THE WAY. HE DROPPED THE ROCK AND PINCHED FINGER BETWEEN IT AND ANOTHER ROCK. A BLOOD BLISTER DEVELOPED. EMPLOYEE THOUGHT IT WAS JUST MASHED HE WORKED REMAINDER OF HIS SHIFT. EMPLOYEE'S FINGER CONTINUED TO HURT. HE WENT TO THE EMERGENCY ROOM ON 11/18/99. THE TIP OF HIS FINGER WAS BROKEN AS WELL AS HIS WRIST WAS STRAINED.

INJURED AND FELLOW EE WERE UNHANGING ROCK IN JAW. FELLOW EE THREW SMALLER ROCK TO PUSH OUT JAMMED ROCK. THROWN ROCK STRUCK INJURED'S HAND BETWEEN THUMB AND INDEX FINGER.

EE WAS HELPING LOAD A CLAM SHELL BUCKET ON A TRAILER WHEN RUST FELL INTO HIS EYE. HE SAW THE EYE DR ON THE FOLLOWING DAY. METAL WAS REMOVED ON A FOLLOW YOUR APPT ON AUG. 30 1999 A RUST RING WA S REMOVED.

EMPLOYEE WAS WORKING ON A FEEDER, WHEN HE SLIPPED AND FELL AGAINST THE FEEDER. HE WENT TO THE DOCTOR THAT MORNING FOR X-RAYS. HE WORKED THE NEXTSHIFT ON LIGHT DUTY.

THE EE WAS CLEANING OUT GRIZZLY BARS W/ A SLEDGEHAMMER WHILE SWINGING THE HAMMER THE EE STRAINEDHIS BACK

THE EMPLOYEE WAS REMOVING LARGE ROCKS FROM THE CRUSHER. HE LOST HIS GRIP ON A ROCK AND SMASHED HIS LEFT HAND AGAINST THE CRUSHER LINER.

THE EMPLOYEE ON DATE OF THE INJURY PICKED UP ON AN IMPACTOR HAMMER. HE STRAINED HIS SIDE BY DOING THIS TASK AFTER SEVERAL MONTHS WAITING FOR IT TO IMPROVE HE WAS SENT TO A BACK SPECIALIST ON JULY 12.

SHOVELING--STEPPED ON A ROCK--TWISTED LEFT KNEE.

EE WAS WELDING. A LARGE ROCK SLID OFF HOPPER WALL. STRUCK EE ABOVE KNEE ON LEFT LEG. WENT TO ER, XRAYS TAKEN. PAIN PRESCRIPTION GIVEN.

EMPLOYEE CHANGING UNILOADER BUCKET LEFT FOOT CAUGHT BETWEEN HANDLE AND EDGE OF BLADE. EE LOOKED AT FOOT EMPLOYEE CONTINUED WORKING. ALSO CAME IN AND WORKED FRIDAY. WAS OFF SAT, SUN AND MON. BEFORE SHIFT WERE TO BEGIN MON EVENING, HE DECIDED TO GO TO DR DR SAID MAYBE SMALL FRACTURE, WRAPPED UP. WAS TOLD HE MAY CONTINUE WORK.

THE EE WAS BITTEN BY A SPIDER ON HIS LEG. MEDICAL TREATMENT WAS GIVEN IN THE FORM OF AN ANTISERUM.

EE SIMPLY PASSED OUT IN CONTROL ROOM. TAKEN TO ER. DR. SAID HE WAS DEHYDRATED AND STRESS. GIVEN MEDICINE, SHOTS, IV, ADMITTED. RELEASED 1-7-99 @ 1120.

EE SLIPPED ON ICE AND STRAINED GROIN. TAKEN TO ER. PRESCRIPTION GIVEN. OFF WORK 1/4, BACK 1/5.

THE EMPLOYEE WAS LIFTING BATTERIES OVER A RAILING, WHEN HE PULLED A MUSCLE IN HIS BACK.

EE WAS CLIMBING OFF A CRANE, WHEN HE SLIPPED AND FELL. THE FALL FRACTURED HIS LITTLE FINGER.

THE EMPLOYEE STEPPED OFF A PLATFORM AND TWISTED HIS KNEE. THE EMPLOYEE HAS BEEN SEEING THE DR ABOUT HIS KNEE. AT NO POINT WAS HE PLACED ON LIGHT DUTY UNTIL THE DR DECIDED TO DO ARTHROSCOPIC SURGERY ON 3-26-99.

EMPLOYEE CLEANING OUT SCREENS. HAND CAUGHT IN SCREEN AND WAS CUT.

EE WAS STEPPING ONTO A BELT WITH WELDING LEADS. THE LINES CAUGHT ON EE'S BOOT. WHEN HE PULLED OR JERKED THE LINE HE TWISTED HIS BACK.

EE DISASSEMBLING CONVEYOR FRAMEWORK. HAND CAUGHT IN PINCH POINT.

EE WAS PLACING SCREENS IN A SCREEN BOX. AS HE STEPPED INTO THE BOX HE BANGED HIS LEFT KNEE. HE DIDN'T NOTICE ANY PROBLEMS UNTIL 11:30AM AT THISPOINT HE WAS SENT TO DR

EE WAS TRYING TO START A CHAIN THROUGH AN ELECTRIC WINCH. HIS FINGER GOT CAUGHT IN A PINCH POINT CUTTING FINGER. THE CUT REQUIRED A COUPLE STITCHES.

EE WAS TRYING TO BREAK LARGE ROCKS WHICH PLUGGED THE #1 JAW CRUSHER. WHILE HE WAS STRIKING THE ROCK WITH A SLEDGE HAMMER A PIECE OF ROCK FLEW UP STRIKING HIS ARM. THE ROCK CUT HIS ARM REQUIRIN G 5 STITCHES.

EE WAS WALKING THROUGH THE SHOP AS HE STEPPED OVER A TRAILER TONGUE HE BANGED HIS SHIN. SEVERAL WEEKS LATER INFECTION SET IN CAUSING THE REMOVE OF DEAD TISSUE BY THE DR 6-16-98.

EE WAS GREASING THE PLANT WHEN HE FELT A POP IN HIS KNEE. HE AHD NO PROBLEMS FOR AWHLE,BUT IT THEN STARTED TO BOTHER HIM AFTER A WEEK. HE WEN TO A DR BUT WAS RELEASED WITH NO RESTRICTIONS. IT STILL BOTHERED HIM, SO HE WAS SENT TO THE DR ON 1-12-98. THIS TIME HE WAS PLACED ON RESTRICTED UNTL A SPECIALIST COULD LOOK AT IT.

EE WAS WELDING IN A ROCK FEED CHUTE AT THE SECONDARY SCREENING STATION AND RECEIVED BURNS TO THE EYES, DUE TO WELDING FLASH. WAS TREATED AT ER. DR PRESCIBED OINTMENT FOR EYES. RETURNED TO WORK NEXT SHIFT.

EE WAS MOVING BY HAND AN ELECTRICAL STARTER BOX INTO THE MCC BUILDING WHEN HIS RIGHT ARM STRUCK THE OPENED DOOR OF AN ADJACENT STARTER BOX.

EE WAS WORKING ON THE GROUND, USING HAMMERS TO FREE EXCESS ROCK. HE FELL BACKWARDS ON METAL INJURING HIS BUTTOCKS & SHOULDERS.

EE WAS CLEANING MATERIAL OUT FROM UNDER THE BELTOF THE IMPACT CRUSHER. HE STATED HE TURNED TO THE LEFT WITH A SHOVELFUL OF MATERIAL AND FELT A BURNING IN HIS BACK. EE INFORMED HIS OFFICE 3/11/ 97 THAT HE HAD HURT HIS BACK & NEEDED TO GO TO THE DR. EE WAS DIAGNOSED WITH A STRAIN TO HIS BACK

EMPLOYEE WAS TRYING TO BREAK A ROCK LODGED IN THE CRUSHER. A ROCK FELL TOWARD THE EMPLOYEE. HE PUT HIS HANDS UP AND HIS HEAD DOWN TO SHIELD HIS FACE. THE ROCK WENT OVER HIS HEAD AND FELL ON HI S HARD HAT AND NECK. AT THE TIME OF THE ACCIDENTHE WAS ASKED IF HE WAS HURT & IF HE NEEDED TO SEE A SR. HE INSISTED THAT HE WAS FINE & RETURNED TO WORK. SAW A DR. 2-20-97 & BEGAN LOSING TIME.

ROCK WAS HUNG IN JAW CRUSHER WERE REMOVING 50# ROCKS BY HAND FROM JAW. ROCK SLIPPED OT OF ANOTHER EMLOYEE'S HAND AND MASHED THE TIP OF LITTLE FINGEER, MIDDLE FINGER, AND RING FINGER.

EE WAS TIGHTENING BOLT ON HAULPAK 210M DUMP TRUCK WITH A WRENCH. THE WRENCH ALIPPED AND CUT HIS FOREHEAD.

EE WAS HOLDING A HAMMER IN POSITION WHILE ANOTHER EE WAS USING A DRIVING BAR TO MOVE THE HAMMER BAR. EE THOUGHT COWORKER HAD STOPPED STRIKING THE BAR. EE MOVED HIS FINGER NEAR THE END OF THE B AR JUST AS COWORKER STRUCK THE BAR.

OUR EE WAS WELDING IN A BIN WITH TWO OTHER WELDERS AND THE REFLECTION OF THE OTHER WELDERS RESULTED IN SEVERE FLASHBURNS TO EE'S EYES.

EMPLOYEE WAS ATTEMPTING TO CONNECT A WINCH CABLE TO THE BARGE. THE EMPLOYEE REACHED DOWN TO GRAB THE CABLE AND HIS LEFT HAND GOT CAUGHT BETWEEN THE SOFT ROPE, THAT WAS HOLDING THE BARGE AND TH E KERVIL.

EE WAS CLEANING A CONVEYOR TAIL PULLEY IN THE SHOP. HE STOPPED FOR LUNCH BREAK, WASHED HIS HANDS AND NOTICED HIS FINGER WAS SORE. HE DUG OUT A SMALL PIECE OF METAL. THIS INJURY WAS REPORTED A S FIRST AID. 3 DAYS LATER HIS FINGER IS SWOLLEN & INFECTED. HE RECIEVED TREATMENT AT HOSPITAL FOR INFECTION EE WAS WEARING GLOVES.

EE WAS KNEELING ON HIS KNEES USING A BELT KNIFE CUTTING THE INSULATION OFF A WELDING CABLE WHEN THE KNIFE SLIPPED CAUSING A DEEP LACERATION TO LEFT THIGH REQUIRING SUFURES.

EE & EE WAS LIFTING A 6IN X6IN X8FT WOODEN TIMBER APPROXIMATELY 41/2 TO PUT ON BACK OF BOOM TRUCK EE NOTICED HIS BACK WAS HURTING LATER & GOT WORSE AS THE DAYWENT ON HE WAS THEN TAKEN TO HOSPI TAL & XRAYED

INJURED WAS WELDING IN JAW FEEDER.A ROCK WEIGHING ABOUT 15 LB. FELL FROM THE JAW DUMP HOPPER AND ROLLED DOWN THE FEEDER STRIKING HIM ON THE LEFT SHOULDER AND LEFT LEG.THIS ACCIDENT WAS ORIGINA LLY REPORTED AS A FIRST AID INJURY.

EMPLOYEE WAS PULLIGN ELECTRIC CORD OUT THE BACK OF THE WELDIGN TRUCKA ND WRENCH WAS TANGLED UP I TEH CORD CAUSING THE WRENCH TO FALL ON EMPLOYEE'S FOOT BEHIND THE STEEL TOE.

EE WAS STARTING TO CUT A PIECE OF METAL WHEN THE TORCH CAME IN CONTACT WITH THE CONCRETE CAUSING DUST AND GRIT TO BLOW IN EYE.

EE WAS USING A TORCH TO CUT A BOLT AT THE 2 PLANT SCREENING TOWER THE TORCH SLIPPED OUT OF HIS HAND AND HE TRIED TO CATCH THE TORCH AND BURNED HIS RIGHT WRIST.

EE WAS LIFTING SWING CYLINDER FOR THE BACKHOE AT THE #2 JAW, WHEN HIS RIGHT HAND SLIPPED CAUSING EE TO CATCH FINGER BETWEEN CYLINDER AND BACKHOE BASE.

EE WAS USING A BELT KNIFE TO CUT A 3/4" RUBBER HOSE. THE KNIFE SLIPPED STRIKING EE ON THE LEFT THUMB AND CAUSING A LACERATION.

EE WAS SWINGING A SLEDGE HAMEMR WHEN HIS FINGE RWAS CAUGHT BETWEEN THE HANDLE AND A PEICE OF CHANNEL IRON.

EE WAS USING A BELT KNIFE TO CUT A PIECE OF RUBBER OFF THE PIT BELT. THE KNIFE SLIPPED AND THE POINT OF THE KNIFE PUNCTURED HIS LEFT HAND BETWEEN THE THUMBE AND INDEX FINGER. EE WAS TAKEN TO T HE HOSPITAL AND WAS SUTURED.

EMPLOYEE WAS OPERATING 966 LOADER DOWN THE RAMP WHEN THE ENGINE DIED CAUSING THE LOADER TO RUN INTO THE BERM. EMPLOYEE WAS TAKEN TO THE HOSPITAL AND X-RAYED. ON 12-21-94 EMPLOYEE WAS TAKEN TO SEE DR. AND HE IS TO HAVE A MRI ON 12-22-94.

HE WAS USING A PRY BAR TO HOLD UP STEERING CYLINDER ON A 50 TON TRUCK WHEN THE BAR SLIPPED CATCHING HIS RIGHT HAND BETWEEN THE BAR AND CONCRETE FLOOR.

EMPLOYEE WAS STARTING TO STEP DOWN OFF AN ELEVATED PLATFORM WHEN HE CAUGHT HIS HEEL OF HIS BOOT AND FELL DOWN 2 STEPS CATCHING HIMSELF WITH HIS LEFT HAND AND STRIKING HIS BACK ON AN I-BEAM.

EMPLOYEE WAS GETTING OUT OF THE BOOM TRUCK. STEPPED ON RUNNING BOARD WITH MUD ON BOOTS CAUSING HIM TO FALL STRIKING HIS MOUTH ON ARM REST ON DOOR.

EMPLOYEE WAS USING A HYDRAULIC JACK TO PUSH A PIN OUT OF A LOADER BUCKET WHEN THE HOSE CONNECTOR CAME LOOSE STRIKING EMPLOYEE ON RT LEG

HE WAS HELPING THE WELDERS LINE UP THE BOLT HOLES ON THE SOLIDS PUMP. HE WAS ON HIS HANDS AND KNESS. WHEN HE STOOD UP HIS FINGER WOULD NOT STRAIGHTEN.

EMPLOYEE WAS UNSTOPPING CHUTE OVER SPOKANE CRUSHER. EMPLOYEE HA DHIS LEFT HAND ON THE HANDRAIL WHEN A 4" ROCK FELL APPROIMATELY 10' STRIKING EMPLOYEES HAND.

EMPLOYEE WAS TIGHTENING BOLT ON THE SKIRT BOARD OF THE RIVER CONVEYOR. THE BOLT BROKE, CAUSING THE RATCHET TO STRIKE EMPLOYEE IN THE LIPS AND CHIPPING ONE TOOTH AND CRACKING ANOTHER.

55061S IN THE BED OF HIS MECHANICS TRUCK WHEN HE STARTED TO GET OUT HE CAUGHT HIS PANTS ON SOMETHING. HE FELL TO THE GROUND CATCHING HIMSELF WITH HIS RIGHT HAND. HE WENT TO THE DR AND WAS X RA 85407 RAY SHOWED HAIRLINE FRACTURE OF RIGHT ARM.

95149ED WAS PICKING UP A ROCK SAMPLE WEIGHING APPROXIMATELY 15 POUNDS.HE FELT A SHARP PAIN IN HIS LOWER BACK.INJURED CONTINUED TO WORK-HE THOUGHT THE PAIN MIGHT SO AWAY.WENT TO CHIROPRACTOR AT 08?30PM 08-20-92.

54730PULLING 3 COPPER WIRES WEIGHING 125 LBS WHEN FELT A PAIN IN NECK. EMPL HAS BEEN GOING TO CHIROPRACTOR FOR TREATMENT. EMPL HASNT MISSED ANY WORK FROM INJURY.

EE WAS WALKING DOWN STEPS HOLDING ON TO THE HANDRAIL WHEN HIS RIGHT HAND HIT THE SUPPORT POST CAUSING HIS THUMB TO BEND BACK.

I.NAME LIT THE TORCH AND THEN IT WENT OUT.SHUT OFF THE ACETYLENE & OXYGEN,HIT THE TRIGGER TO BLOW OUT THE TORCH.STARTED TO RELIGHT TORCH,TURNED ACETY. ON AND REACHED FOR THE STRIKER.TORCH TIP BRUSHED AGAINST GLOVE AND CAUGHT FIRE.JERSEY GLOVE ON LEFT HAND CAUGHT FIRE AND CAUSED SEVERE BURN TO HAND.

STEPPED ON ROCK FELL ON R WRIST

EMPLOYEE WAS REMOVING SHAFT OF CONVEYOR BELT WINDER FROM ROLL OF BELT WITH THE AID OF A WINCH TRUCKS WINCH WHEN THE SHAFT CLEARED THE BELT ROLL IT FELL TO THE GROUND CATCHING THE EMPLOYEES 2ND FINGER OF LEFT HAND BETWEEN GROUND AND SHAFT.

EMPL WAS SWITCHING BARGE FROM DOCK. BARGE WAS DRIFTING DOWNSTREAM THEREFORE HAD SLACK IN CABLE WHEN IT TIGHTENED IT CAUGHT EMPL;S FEET & CAUSED HIM TO FALL ON LOADED BARGE. THEREFORE CASUING C UTS LACERATION & PUNCTURES TO BOTH LEFT & RIGHT LEGS.

EMPLOYEE WAS CARRYING TWO CONTAINERS EQUALING THREE GALLONS OF OIL. WHEN HE STEPPED OFF THE BERM IN FRONT OF THE TRUCK. HIS MISJUDGED THE APPROXIMATE 2' DROP OFF, AND FELT PAIN IN HIS RIGHT KNEE.

EMPLOYEE WAS REMOVING A SREEN FROM THE SHAKER. HIS HAND SLIPPED OFF OF THE SREEN AND CAUGHT HIS ARM ABOVE THE GLOVE. CUT UPPER FOREARM.

METRO SPECIAL POLICE EMPLOYEE WAS WALKING THROUGH AN INTERNAL OPEN DOORWAY.SHE TRIPPED OVER DOOR FACING.SHE FELL FORWARD AND TWISTED HER LOWER BACK AND LEFT LEG.WE RECEIVED NOTICE TODAY 08-23- 89 THAT SHE INCURRED LOST TIME.

EMPLOYEE WAS LIFTING A 1 1/2" GASOLINE PUMP INTO A STORAGE BOX ON THE UPPER LOADING DOCK.WHEN HE FELT A PAIN IN LOWER BACK.

WHILE CLEANING ROCK OUT OF INTERIOR COMPARTMENT OF HBC 1625 HE WAS LIFTING BOULDER OUT OF HOLE IN SIDE OF BARGE AND WRENCHED BACK MUSCLE.

AN EMPLOYEE OF METRO SPECIAL POLICE, A CONTRACTOR FOR SECURITY SERVICES AT THE QUARRY, BRUISED HIS KIDNEY. HE WAS CHECKING A METER AT OUR GENERATOR & LOST HIS FOOTING ON THE STEPS. HE SLIPPED APPROX. ONE FOOT FROM ONE STEP TO THE NEXT. HE FELL ON THE HAND RAIL. HE DID NOT FALL DOWN COMPLETELY.

EMPL WAS PUMPING WATER OUT OF HOPPER BARGE WITH 3" PUMP. WHEN HE BENT OVER COMMING TO MOVE HOSE HE FELT PAIN IN UPPER BACK. HOSE WAS 13' TO 14' LONG & FULL OF WATER.

EMPLOYEE WAS ATTEMPTING TO HAND LOAD AN OIL COOLER ONTO A SERVICE TRUCK OIL COOLER WEIGHTED APPROX 40LBS AS HE PULLED ON COOLER HE FELT PAIN IN LOWER BACK LOST TIME ACCIDENT AGGRTAVATED EXISTI NG BACK PROBLEM

EMPL GETTING BARREL OF OIL OUT OF PICKUP ONTO BARREL RACK.TWISTING ON BARREL FELT PAIN IN LOWER BACK.LOST TIME ACCIDENT.

EMPLOYEE WAS TRYING TOMOVE IMPACT HAMMER WITH TOOL BAR & WHEEL DOLLY TO SHOP DOOR FOR LOADING SO IT COULD BE SHIPPED FOR REPAIR UNIT SLIPPED OFF OF DOLLY & TOOL BAR HIT EMPLOYEE HIGH ON INSTEP BRUISING IT LOST TIME ACCIDENT

PULLING SLAB FJORM IMPACOTR LEAVING AGAINST AND OVER PART MAHCINE TO JPUL LEVERS PRESSURE EXERTED CAUSED CRACKED RIB. EMP THOUGHT HE PULLED, LATER DISCOV. RIB WA> CRACKED.

EMPL WAS HELPING TO PUMP BARGES. HE WAS CARRYING 3" PUMP DOWN SIDE OF HOPPER BAGE WHEN HE HUNG HIS FOOT UNDER KEVIL CAUSING HIM TO FALL INTO RIVER. EMPL STRUCK FACE & NOSE ON PUMP WHEN HE F ELL.

EMPLOYEE WAS HAULING FROM THE PLANT. SAID HE HAD A HEADACHE AND HAD TAKEN HIS HARD HAT OFF. HE HIT A DITCH CROSSING ROAD A 1/4 X 0 PILE TO HARD AND THE JOLT CAUSED HIM TO STRIKE HIS HEAD ON A BOLT PROTRUDING IN CAB.

EMPLOYEE WAS DISMOUNTING EQUIPMENT WHEN HE TWISTED HIS LEFT ANKLE ON LADDER AND FELL TO THE GROUND

EMPLOYEE WAS STRIKING A BEARING BRACE WITH A HAMMER. A PIECE BROKE OFF AND STRUCK HIM IN THE NECK. A PIECE LODGED IN HIS NECK.

EMPLOYEE WAS OPERATING 50 TON TRUCK #111.HE HAD STOPPED UNIT AND WAS EXITING CAB DOOR WHEN DOOR SLAMMED ON HIS HAND.

EMPL WAS USING PRY BAR TO FREE LARGE ROCK FROM CRUSHER FEED TUBE WHEN ROCK SHIFTED CATCHING PRY BAR CAUSING PRY BAR TO CATCH EMPL'S FINGER BETWEEN LARGE ROCK & FEED TUBE.

EMPLOYEE WAS REMVOING A TOOL BOX ON WELDING SERVICE TRUCK. AROLL OF ROPE BEHIND THE TOOL BOX PREVENTED THE LID FROM LAYING BACK IN POSTION. THE LID FELL, FRACTURING HIS RIGHT HAND INDEX FING ER.

EMPLOYEE WAS REMOVING A ROCK THAT HAD LODGED IN THE BARS AT THE NUMBER TWO JAW FEEDER USING A EIGHT POUND SLEDGE HAMMER. EMPLOYEE CAUGHT HIS LEFTHAND LITTLE FINGER BETWEEN THE HAMMER HANDLE A ND THE SIDE OF THE FEEDER WHILE STRIKING A ROCK.

EMP WAS WORKING3AS DECKHAND, HE WAS PULLING A WIRE ROPE UP ON BARGE DECK, THE ROPE WAS HANGING IN THE WATER, WHEN HE REACHED TO GRAB THE ROPE A LONG BURR STRUCK HIM IN THE ARM ABOVE HIS GLOVE

EMPLOYEE WAS CA9RYING A FIVE GALLON BUCKET OF METHANOL UP A LADDER TO WINTERIZE DRILL DUST SUPPRESENT.WHILE THE EMPLOYEE WAS CLIMBING THE LADDER,HE FELT A STRAIN IN HIS BACK.

EMPLOYEE WAS WA5KING IN PARKING LOT & SLIPPED TWISTING HER RIGHT KNEE

EMPLOYEE WAS CU7TING THE TILT LINE COVER LOOSE ON D8H TRACTOR DOZER WITH A CUTTING TORCH.FOR THE FINAL REMOVAL OF THE COVER THE EMPLOYEE STUCK THE COVER WITH A SLEDGE HAMMER.THE COVER BROKE LO OOSE STRIKEING 7HE EMPLOYEE'S LEFT FOOT.THE EMPLOYEE SURRERED A CONTUSION TO THE LEFT FOOT.

THE EMPLOYEE WA8 TRAINING ANEMPLOYEE TO OPERATE THE JAW CRUSHER. A SEVERE THUNDERSTORM WAS APPOCHING AND THE EMPLOYEES WERE EXITING THE CONTROL HOUSE. THE INJURED EMPLOYEE SLIPPED, CAUGHT HIMS ELF ON THE DOOR3FRAME. THE OTHER EMPLOYEE CLOSED THE DOOR ON THE INJURED EMPLOYEE'S FINGERS. THE EMPLOYEE RECEIVED A LACERATION TO HIS SECOND AND THIRD DIGITS, RIGHT HAND, AND FRACTURED BOTH

UPPER BARGE CAB5E WAS HUNG BEHIND THE COMBING ON THE BARGE THE EMPLOYEE BENT OVER TO PICK THE CABLE UP

EMPLOYEE PICKED3UP 5 GAL CAN OF DRILL OIL AND SET IT UP ON THE TRUCK DRILL EMPLOYEE DID NOT MISS WORK DUE TO INJURY UNTIL 10/20

EE WAS DESCENDI3G STAIRWAY IN QUARRY OFFICE WHEN HE SLIPPED OR CAUGHT HIS FOORT IN A TURN PIECE OF CARPET CAUSING HIM TO FALL APPROX 6 STEPS HITTING HIS HEAD & SHOULDER ON THE WALL AT THE END OF THE STAIRWA2 EE WAS NOT USING HANDRAIL.

EMPLOYEE STEPPE8 DOWN FROM A LADDER ON A 50 TON HAUL TRUCK TO THE GROUND HE FELT A PAIN IN HIS KNEE EMPLOYEE DID NOT MISS WORK DUE TO THE INJURY UNTIL 10-16 AT WHICH TIME OUTPATIENT SURGERY W AS PERFORMED 3

EMPLOYEE WAS RE1AIRING A LEAK IN A FUEL LINE GOING TO A MAIN ENGINE HE WAS CUTTING THE RUBBER LINE WITH A KNIFE WHEN HE CUT HIS THUMB

EE WAS PULLING 5 WOOD CRATE CONTAINING A CAST METAL HOUSING OUT OF LAODER BUCKET WHEN THE CRATE CLEARED THE BUCKET THE HOUSING SHIFTED &C AUGHT HIS FINGER BETWEEN THE CRATE & HOUSING.