Brooksville Quarry Metal/Non-Metal

Softrock Haul Truck Operator was operating a CAT 777G Haul Unit too close to berm on left side of road and ran into berm knocking off left wheel of Haul Unit. Truck rolled over onto its left side. Operator jumped out of truck injuring left arm, elbow and left foot.

On 6/18 employee was involved in a vehicular collision which resulted in minor back pain to lower back. Employee did not want to seek medical attention on that date. On 6/24 employee was still experiencing back pain and was taken to the doctor where EE was placed on restricted duty.

Maintenance Mechanic was walking to the work station and rolled ankle resulting in a sprain.

Employee was driving company truck (Ford F150) and veered off a paved road and hit a concrete barrier causing airbags to deploy striking face and chest. Employee sustained a cracked sternum and broken nose.

On 6/8/20 Employee was moving a tow cable and strained EE's right shoulder. Reported Incident on 6/9/20 and did not ask for medical attention on that date. Taken to doctor on 6/11/20 and given light duty work restrictions by physician.

Employee was moving a tow cable and a wire from the cable punctured EE's left forearm resulting in a small puncture wound. Employee went to doctor following day and received a tetanus shot. Back to work with no days off.

Employee was swinging sledge hammer and strained right shoulder. Taken to doctor for examination and EE was placed on light duty.

Operator dismounting dragline. Guardrail safety chain across ladder access had been unlatched and hanging down in close proximity to access ladder. While dismounting, operator's finger became snagged on the latch on safety chain, lacerating the finger.

Employee was stepping down from truck, missed a step and fell on the ground.

Employee was operating a McCloskey ST110 Portable Stacker via remote control and ran over ee left foot with the left track of the machine, breaking 2nd and 3rd metatarsal bones in foot.

Employee was removing hydraulic line on gate actuator and nut on hydraulic hose hit employee in the mouth and chipped the Left Front Tooth. No other injury sustained, No Restrictions. Came back to work that day. Needs to get tooth repaired on 5/15/2018.

Employee was working on Portable Crusher and was struck by a blunt object resulting in an abrasion and bruise to the lower back and pain to EE's torso.

Haul Truck Operator was bending over to get into the cab of EE's CAT 777 Haul Unit and felt a sharp pain in EE's lower back. The pain persisted and EE notified EE's supervisor and was sent home. The next day EE went to the clinic and was diagnosed with Sciatica. EE was placed on light duty for 1 week. EE returned to work on 8/26.

EE was removing the belly pan off of a 615 Cat water wagon. When EE was removing the last bolt, the pan came down and landed on hand and wrench. This caused a small cut on the palm of hand below the index finger. The cut required 4 stitches. EE returned back to work and hour and a half later.

On 1/14/2016 Mechanic sustained a puncture wound from a fractured piece of metal after striking a crusher hammer with a sledge hammer. Employee taken to doctor and released to Full Duty, No Restrictions. On 1/29/2016, the employee was taken to doctor for follow up and placed on restricted duty, No heavy lifting. On 1/29/2016 this injury became a reportable injury

Employee was lifting the lid of a metal container and the lid hit his forehead and caused a laceration on the left side of his head that needed 7 staples. He was released to full duty.

On 8/21 employee sustained a puncture wound while using a hammer and punch. On 8/25 he was complaining that there was a piece of metal in his left hand and taken to the doctor. The hand was x-rayed and a piece of metal was. He was sent back to work with NO Restrictions. On 9/2 he had the piece of metal surgically removed and placed on restrictions with limited hand use.

Fixed Plant Mechanic was replacing a conveyor belt on a Power Screen and sustained a small laceration to the top of his left ring finger while he was trimming the belt. He was taken to the ER and the laceration was cleaned and glued together. No restrictions were given. He was given a tetanus shot and prescribed antibiotics.

Fixed Plant Mechanic was helping Mechanic remove a 200 pound bearing from a pallet. During the removal process, they dropped the bearing and it landed on top of Plant Mechanic's left foot, which resulted in the fracture of 3 metatarsal bones.

Electrician was walking down the North 42 Inch conveyor catwalk, slipped and fell backwards. He landed on his left elbow and felt pain in his left shoulder. He was taken to the doctor the following day (11/08/2013) and placed on light duty (no overhead work) and given pain medication.

An employee was handing a piece of steel plate (2'x3') from a shaker screen to EE and the plate slipped out of his hands and pinched EE's left hand between the steel plate and a pipe. He broke a bone in his left hand.

Employee was walking down a concrete slope, he slipped and fell backwards hitting the back of his head. His head sustained a 1.5 inch laceration which required 6 staples.

Employee was carrying a block of wood while walking behind his service truck. His right hand collided with a step on the back bumper, causing his finger to be smashed between the block of wood and the bumper. The employee sustained a laceration to his right ring finger requiring 10 stitches.

Employee was climbing down the ladder of a CAT 777D Haul unit and lost his footing. He fell backwards and hit his head on the ground resulting in a 1 inch laceration to the back of his head. The injury required 3 stitches.

Employee was using a utility knife to cut a piece of skirt rubber. The knife slipped and cut the employee's right thigh. Employee sustained a three inch laceration that required 6 stitches. Employee was returned to full duty with no restrictions.

Employee was turning handle to a winch and let go of the winch handle. The handle to the winch spun backwards, hitting the employee on top of the left hand, breaking two bones in the hand.

Employee was removing a pin from a pneumatic actuator utilizing a sledge hammer and a punch. Upon striking the punch with the hammer, a small piece of metal from the hammer punctured the employee's left hand. The metal had to be removed by a physician.

Employee was lifting the hood on the Mack Blasting Truck and felt a sensation in his L lower abdomen. Later that day he began to experience pain in the area. He was in pain the next day and sought medical treatment. He was diagnosed with a hernia in his L lower abdomen.

On 8/11/07 employee was welding a discharge lip to a shaker screen. He was supporting the metal lip with his right arm. He turned his body and felt a pop in his shoulder. He felt minor pain in the shoulder for several months and on 1/2/08 he asked to see a doctor. Employee was released to full duty on 1/2/08 and given a prescription steroid for inflammation.

Employee was washing off scale with water hose. She lost her footing and fell backwards landing on her left hand and buttocks. She suffered a sprain to her left wrist.

Employee was lifting an 80 pound wear liner into crusher. During the lift he felt a pop in his left shoulder and experienced pain. Employee was taken to the doctor the next day and treated for muscle strain.

Employee was climbing up the ladder of a Cat 777 Haul unit and her hand slipped on the railing, but she did not fall. Later that evening she complained of back pain. The back pain persisted for several days. On May 24 she asked to see a physician because the back pain had not improved. Doctor reveiw revealed muscle spasm and she was treated with medication and placed on light duty.

Employee and two other mechanics were lifting a metal skirtboard in place. During the lift the employee felt a pop in abdomen. A small lump in lower abdomen was noticed the next day. Employee visited physician for diagnosis. Employee was diagnosed with small hernia in abdomen. Employee placed on light duty and scheduled for surgery.

Employee was tightening bolts on screen deck with a 3/4 inch impact wrench. Socket and wrench separated during tightening and wrench traveled up employees arm inflicting a 1 inch laceration on his wrist requiring six stitches.

Employee was washing spilled material underneath plant with hose. She turned valve off on the hose she was using and another hose that was running underneath plant came loose from its location due to the pressure change and hit her elbow. Her elbow remained sore for a few weeks and she was taken to the doctor on 9/26/2005 for evaluation.

Employee was chipping slag from a weld with a hammer. A piece of the slag penetrated his left wrist. He visited the doctor and the incident was initially treated as a first aid. Upon returning to the doctor (8/17/05) for a follow up visit, the doctor recommended the piece of metal be removed. The metal was removed on 8/19/05 and a stitch was placed over the wound.

Employee was stepping off of a 920 Loader. When his right foot hit the ground, he felt a pain in his right knee. His knee continued to hurt throughout the day and he was taken to the doctor. He was placed on light duty and scheduled for further diagnostics of the knee.

EE WAS DESCENDING THE SOUTH LOWER STAIRWAY FROM THE PRIMARY CRUSHER DECK. ABOUT THE THIRD STEP DOWN, BOTH FEET SLIPPED ON THE STEPS, LEAVING CONTACT WITH HIS HANDS ONLY. EE TIGHTENED HIS GRIP ON THE HANDRAILS TO PREVENT BODY CONTACT WITH THE STAIRS. IN DOING THIS, EE CLAIMS TO HAVE TWISTED HIS LOWER BACK.

A Commercial Truck entered the scale and knocked the drain pan out of position with the tarp rack. Scale house operator climbed the ladder on the side of the truck to put the pan back into place. When the pan dropped back into position, the operator's thumb got pinched between the pan and the chute. Right thumb tip was cut, his nail was removed and he received six stitches.

Employee was walking down a flight of stairs in the Screenhouse and fell. Aparently, the employee missed the first step, fell on his back and slid down the length of the stairway. He dislocated his right shoulder as a result of the fall.

A piece of metal apparently entered employee's Left eye after wiping sweat off of his brow with a shirt sleave. He rinsed his eyes in the eye wash station and felt better. The next day he was in pain, so he was taken to the doctor where the object was removed. The cornea was scratched.

Employee was working on the Pond #12 pump platform. Another employee tossed him a bottle of oil from the bank (The toss was too high). Terry fell backwards trying to catch the bottle and landed on his left hand, breaking the wrist.

EE WAS CLIMBING DOWN A FIXED LADDER IN SCREEN HOUSE & ATTEMPTED TO STEP OFF LADDER TO A STAIRWAY JUST TO LEFT OF LADDER. (THERE WAS A HOSE PILED UP UNDERNEATH LADDER.) WHEN EE PLACED HIS FOOT ON THE STEP BELOW, IT SLIPPED OUT FROM UNDER HIM & HE FELL ON HIS TAILBONE. BECAUSE OF THE HOSE BEING IN THE WAY, EE DID NOT HAVE A SUITABLE PLATFORM TO EXIT THE LADDER.

ELECTRICIAN WAS STEPPING INTO THE BED OF A WORK TRUCK AND STRUCK HIS RIGHT KNEE ON THE TAILGATE OF THE TRUCK. HE WAS EXAMINED BY A DOCTOR THE AFTERNOON OF THE ACCIDENT AND GIVEN A DIAGNOSIS OF "MUSCULAR CONTUSION". HE CLAIMED TO HAVE A GREAT DEAL OF PAIN, SO THE DR PRESCRIBED PAIN AND ANTI-INFLAMMATORY MEDICATION. WAS PUT ON LIGHT DUTY FOR A WEEK.

WHILE TROUBLE SHOOTING A 4150 MAIN BREAKER PANEL, EE MAD CONTACT WITH 4160 VOLTS IN THE BUS BAR PANEL NEXT TO THE MAIN BREAKER. EE FAILED TO FOLLOW POSTED PROCEDURES BY VISUAL CONFIRMATION THA T THE KNIFE SWITCHES FOR THE BREAKER WERE DISENGAGED EVEN THOUGH THE MAIN BREAKERE SWITCH WAS IN THE OFF POSITION. THE BREAKER SWITCH SHAFT WAS BROKEN.

EE WAS CUTTING BUT HAD HIS LEFT HAND DIRECTLY ACROSS FROM HIM. THE CUTTING UTENSIL SLIPPED AND HE CUT HIS LEFT THUMB. (THE DELAY IN REPORTING THIS WAS NOTED DURING AN INTERAL AUDIT).

EMPLOYEE WAS DRIVING A HAUL TRUCK. HE SAYS HE WAS REACHING INTO HIS LUNCHBOX FOR A SODA WHEN THE NEXT THING HE KNEW, HE WAS OFF THE HAUL ROAD. HE RODE THE BERM FOR 20 FT AND THEN ENDED UP IN T

EE WAS USING A CHISEL BRAND NEW TO SPREAD LINKS ON A TRACK SYSTEM. THE CHISEL SNAPPED IN HALF AND CUT HIM ABOVE THE RIGHT EYEBROW.

EMPLOYEES WERE FIXING THE ENTRANCE GATE WHEN INJURED RELEASED HIS SIDE, THE OTHER EE SLID THE BLOCK FURTHER AND CAUGHT EE'S INDEX FINGER(LEFT).

EE WAS ADJUSTING SEAT IN HAUL TRUCK. HE OVERADJUSTED THE WRONG WAY AND THE SEAT COLLAPSED. THE SEAT WAS APPROXIMATELY 2 WEEKS OLD. THE INCIDENT HAPPENED IN THE TRUCK LOT BEFORE HE STARTED THE TRUCK.

EE WAS HELPING CHIP CEMENT BUILD UP. HIS PANTS GOT WET AND CEMENT GOT INTO A SMALL ABRASION. HE THOUGHT IT WOULD CLEAR UP BUT IT DIDN'T AND GOT INFECTED. FIRST REQUEST FOR MEDICAL TREATMENT ON 4/12/01.

EE WAS WELDING. HOOD & LENSES CHECKED OUT AND WERE ALL RIGHT BUT WERE REPLACED ANYWAY. ONLY CAUSE DETERMINED WAS WATER REFLECTING ON METAL. EE DID NOT REALIZE PROBLEM UNTIL 2100 HOURS THAT NIG HT.

EE PLACED HIS HAND ON DOOR JAM AND SPLINTER LODGED UNDER HIS FINGER NAIL.

SUPERVISOR WAS HELPING ANOTHER DEPT TO DISABBEMBLE A PUMP. THE BRAKE ASSEMBLY BREAKING WERE STUCK. WHEN THE ASSEMBLY WAS LOOSENED IT WENT TO REVERSE CATCHING HIS THUMB DUE TO UNKNOWN PRESSUR E IN THE BASE OF THE PUMP.

EMPLOYEES WERE CHANGING ROLLERS. AS THEY TIPPED A ROLLER TO REMOVE IT, IT HIT AN EMPLOYEE'S LEFTTHUMB, PINCHING IT BETWEEN THE ROLLER & THE BELTFRAME.

EE WAS REMOVING A HOIST FRICTION HE DID NOT WEAR GLOVES & WAS CUT RESULTING IN 6 STITCHES

EE STOPPED HIS HAUL TRUCK TO TALK TO ANOTHER DRIVER. HE LEFT TRUCK IN GEAR AND WHILE HE WAS STANDING ON HIS CATWALK, HIS HAUL TRUCK ROLLED INTO THE OTHER HAUL TRUCK. HE WAS PINNED AND GRABBED ONTO THE BED OF THE OTHER HAUL TRUCK, DROPPED TO THE GROUND, RAN AFTER HIS HAUL TRUCK, CLIMBED UP AND STOPPED HIS HAUL TRUCK. HIS INJURIED OCCURRED AT IMPACT.

EMPLOYEE WAS MAKING REPAIRS ON AN AIR CONDITION-ING SYSTEM ON A LOADER. HE THOUGHT HE'D TURNED THE DISCONNECT TO THE OFF POSITION; HIS KNEE HITTHE REMOTE START WHILE MAKING THE REPAIRS & THE ENGINE STARTED.

EMPLOYEE WAS REMOVING BOLTS TO CHANGE OIL ON AN ARTICULATING TRUCK AND WAS HOLDING UP THE BELLY PAN WHEN HE LET THE PAN DROP, HE DIDN'T MOVE HIS HAND OUT OF THE WAY ON TIME.

EE SAYS THAT WHILE HE & 2 OTHER EE'S WERE ATTEMPTING TO REMOVE A TOOL BOX MODE OF 3/8" PLATE, HEWAS HOLDING IT & HURT HIS BACK. HE FRIST BROUGHTBACK INJURY TO OUR ATTENTION 1ST WK OF JUNE. HE WASNT' SURE IF IT WAS WORK RELATED OR JUST AN O LD BULL RIDING INJURY. HE DECIDED TO GO ON HIS OWN BECAUSE HE WASN'T SURE. HE RETD 6/16 WITH NO RESTRICTIIONS. THE BEGINNNING OF SEPT HE HAD TO

EE RAN INTO THE BACK OF A PAN TRK (CONVERTED INTO WATER WAGON) WITH A 55TON HAUL UNIT. WHEN HE REARENDED THE PAN, THE HAUL UNIT BOUNCED CAUSINGA MUSCLE STRAIN IN THE LOWER BACK IT APPEARS THAT HE FELL ASLEEP (CONVERSATION WITH WIFE RE VEALED HE HAD BEEN UP ALL NIGHT THE NIGHT BEFOREWITH A SICK CHILD)

EE STEPPED IN A POT HOLE.

EMPLOYEE STEPPED IN MUD WHERE A FORM BOARD HAD BEEN INADVERTANTLY BURIED.

EE HIT A CLAY POCKET IN HAUL ROAD AND LOST STEERING (HITTING THE CLAY POCKET BROKE THE HYDRAULIC CYLINDER FITTING STEERING.)

EE WAS USING A TORCH TO CUT SOME METAL. A PIECE OF SLAG FLEW INTO HIS SHIRT CAUSING IT TO CATCH FIRE.

EE WALKED UPSTAIRS TO PICK UP CLAMPS AND WALKED BURN DOWNSTAIRS. NO SPECIFIC EVENT WHERE EE REALIZED INJURY. EE TESTED POSITIVE FOR DRUGS-HE WAS SUBSEQUENTLY SUSPENDED.

EE WAS USING A HAMMER, MISSED AND HIT HIS RIGHT INDEX FINGER.

EE WAS OPERATING DRAGLINE WHEN CABLE BROKE ENTERING THE OPERATOR'S CAB.

EES WERE PULLING STEEL CABLE (APPROX 2" IN DIAMETER) WHEN INJURED EE TURNED AND FELT A PAIN N HIS BACK. INJURY WAS NOT REPORTED TO SAFETY DEPARTMENT UNTIL 9-13-99 WHEN MEDICAL TREATMENT WAS RE QUESTED.

WHILE EE'S HAUL TRUCK WAS BEING LOADED BY THE PAYLOADER, THE PAYLOADER OPERATOR ACCIDENTALLY HIT THE BED OF THE TRUCK WITH HIS BUCKET.

EE WAS UNLOADING A TRACTOR OFF OF A LOWBOY.

EE WAS STRIKING A SHAFT WITH A SLEDGEHAMMER WHEN A PIECE OF METAL CHIPPED OFF AND EMBEDDED IN HIS ARM.

EMPLOYEE WAS CLIMBING THE LADDER OF HIS HAUL UNIT AND SLIPPED AND FELL. HE DID HAVE 39 POUNT CONTACT BUT APPARENTLY MISSED THE HANDRAIL HE WAS REACHING FOR.

EE WAS CHANGING OIL IN A HAUL UNIT. WHILE HE WAS CHANGING THE OIL, SOME WAS SPILLED WHERE HE WAS STANDING AND HE SLIPPED, LANDING ON HIS RIGHT ELBOW AND HIP. EE IS CURRENTLY ON MEDICATION FOR HEART PROBLEM WHICH POSSIBLY CONTRIBUTED TO HIS ACCIDENT.

EE WAS CARRYING (2) 5 GALLON BUCKET OF OIL AT THE SAVE TIME. INJURED WAS NOT REPORTED UNITL 4-26-99.

EMPLOYEE WAS CHANGING OUT HAMMERS IN #3 BOHRINGER.

EMPLOYEE EXPERIENCED A SWOLLEN NECK AND NUMBENSS IN LEFT ARM. IT WAS BELIEVED TO BE A NON-WORK RELATED PROBLEM UNTIL 4-29-99, WHEN WE SENT HIM TO THE DR HE HAD BEEN TO A CHIRO ON HIS OWN & WAS TOLD THAT THE INJURY HAPPENED OVER TIME FROM CHANGING TIRES.

EE LOST HIS FOOTING AND FELL ON HIS BUTTOCKS. THIS WAS REPORTED TO HIS SUPERVISOR 4-2-99 AS AN INCIDENT. MEDICAL TREATMENT WAS NOT REQUESTED UNTIL 6-17-99. THIS WAS NOT REPORTED TO THE SAFETY DEPT. UNTIL MEDICAL TREATMENT WAS REQUESTED.

EMPLOYEE WAS WORKING ON A BELT LINE. HE DID NOT HAVE ON A SAFETY HARNESS, HE FELL.

EE WENT TO PICK UP AN OBJECT THAT WAS TOO HEAVY AND HURT HIS BACK. AT THAT TIME WE WERE TOLD IT WAS A STRAIN. WE WERE JUST NOTIFIED THAT THE INJURY WAS A HERNIATED DISC WHICH WAS DISCOVERED TH ROUGH AN MRI. HAD DIFFICULTY OBTAINING INFO FROMEE AND INSURANCE COMPANY. APPARENTLY RELATED TO DEGENERATIVE PRE-EXISTING CONDITION.

THE EMPLOYEE WAS WORKING IN AN AWKWARD POSITION AND STRAINED HIS BACK.

EE WAS WALKING DOWN SOME STEPS WITH MUDDY BOOTS & MUD ON THE STAIRS. HE SLIPPED & FELL STRAINING HIS LOWER BACK.

EE FELL ASLEEP WHILE DRIVING HAUL UNIT. TRUCK ENDED UP ONITS RIGHT SIDE & WHEN THE EE UNBUCKLED HIS SEATBELT HE FELL ONTO THE HANDRAILS AND BROKE HIS LEG.

EE WAS WALKING ALONGSIDE A DUMPING HAUL UNIT WHEN A ROCK FELL OF THE TRUCK AND STRUCK HIM ON TOP OF HIS HEAD HE WAS WEARING A HARD HAT. HE FELL TO THE GROUND WHERE HE INCURRED A LACERATION TO THE BACK OF THE HEAD.

WHILE CLEANING, EE SLIPPED AND FELL.

EE WAS CLIMBING ON AN UNFINISHED PLATFORM TO INSTALL ANOTHER SCREEN, AND AS HE WAS CLIMBING HE SLIPPED TWISTING HS LEFT KNEE.

EE WAS WELDING WHILE STANDING ON IRON ANGLE. HE WAS NOT WEARING HIS SAFETY HARNESS (AS INSTR BY SUPERVISOR) AND FELL/SLID APPROX 15 FT. HE WWAS PUT ON LIGHT DUTY AND WHILE ON LIGHT DUTY, MO VED A GENERATOR (WAS NOT TOLD TO, EE DID IT BEC AUSE HE WAS BORED) AND AGGRAVATED THE CONDITON

EE WAS BEATING ON THE KILN DISCHARGE SCREW HOPPER WITH A 10FT PIECE OF HEAVY STEEL. HE HAD BEEN INSTRUCTED TO WAIT UNTIL THE PROPER TOOL HAD BEEN BROUGHT (SLEDGE HAMMER). HE REACHED OVER HIS H EAD AND PULLED A MUSCHLE.

EMPLOYEE WAS ATTEMPTING TO MOVE AN AIR COMPRESSOR. HIS FOOT STUCK IN THE MUD AND HIS RIGHT KNEE TWISTED.

CREW WAS WORKING TO REMOVE LARGE SPRING FROM SOUTH PIT CRUSHER. HYDRAULIC JACK WITH SPACERS WAS IN USE TO ALLOW REMOVAL OF SPRINGS. SPACER WAS NOT TIED OFF AND FLEW OUT HITTING EE IN THE HEAD, SLIGHTLY DEFLECTED BY HIS HARD HAT AND SAFETY GLASSES.

EE JUMPED OFF OF A NON-MOVING FORKLIFT AND STRAINED HIS BACK.

ON 3-94 O&K EE WAS CHECKING OUR SHOVEL TO GET READY FOR PRODUCTION. WHILE WALKING BETWEEN ENGINE COMPARTMENT AND SWING TRANSMISSION HOSE AREA FOOT GOT CAUGHT ON HOT TUBE AND TRANSMISSION WHILE EE WAS STILL IN MOTION. FOOT GOT HUNG CAUSING HIM TO TWIST LEFT KNEE.

OPERATING A 245 CAT BACK HOE.

EE WAS WASHING FROM AROUND TAIL PULLY WITH 1" HIGH PRESSURE WATER HOSE WHEN THE PRESSURE SURGED THE WET HOSE SLIP OUT OF HIS HAND. WHILE TRYING TD OUT CONTROL OF THE HOSE ON EOF THE CLAMPS HIS RIGHT BETWEEN THUMB AND INDEX FINGER.

TROMMEL SCREEN GOOSE NECK. EMPLOYEE WENT INSIDE TO UNPLUG. WHEN IT CAME LOOSE, EMPLOYEE'S FEET WAS WASHED FROM UNDER HIM, TWISTED HIS LEFT KNEE.

OPERATOR WAS MOVING A LONG SECTION OF 10" PIPE WITH 920 CAT LOADER. HE DROVE THE LOADER UP THE EMBANKMENT WITH BUCKET RAISED TO MAXIMUM HIGHT. WHEN HE TURNED THE LOADER FELL OVER.

LOADING ROLLERS INTO PICKUP, GOT FINGER CAUGHT BETWEEN TWO ROLLERS.

CLEANING SPILLED CEMENT FROM UNDERNEATH CONVEYOR BELTS. CEMENT GOT ON HIS ..., ... THROUGH HIS SKIN CAUSING A RASH TO DEVELOP.

OPERATING PAN, DRIVING DOWN HAUL ROAD WITH A FULL LOADF, ... HITCH ON, ... IN 4TH GEAR. HE FELT A ROUGH BUMP & TIGHTNESS IN HIS BACK. OPERATOR STATED HE DIDN'T THINK ANYTHING OF IT UNTIL THE N EXT MORNING WHEN HE WOKE UP.

EE WAS OPERATING A SCRAPER HIT A BUMP & INJURED HIS BACK.

ROCK FELL FROM ABOVE & HIT HEAD BELOW HARDHAT.

EE WAS USING 20 LB SLEDGE HAMMER TO DRIVE OUT BRAKER BELT IN CRUSHER. EE STATED THAT HE PULLED HIS BACK.

EMPLOYEE STATED HE WAS NOT PAYING ATTENTION WHEN HAUL UNIT RAN OFF ROAD INTO DITCH.FRONT WHEEL STRUCK AN OBJECT IN DITCH CAUSING STEERING WHEEL TO SPIN AROUND CATCHING RIGHT THUMB,BROKEN THUMB RESULTED.EMPLOYEE ALSO STATED HE DROPPED A LIT CIGARETTE INTO HIS BOOT CAUSING BURN AT TIME OF ACCIDENT.

EE WAS PUSHING 4X4 FT PC OF METAL OVER BIN SHARP EDGE CUT INDEX FINGER.

WAS USING A 2 INCH PIECE OF PIPE 3 FT LONG TRYING TO PRY THE TUB AWAY FROM THE CHAIN CHAIN WAS RUBBING IN TUB WHILE ATTEMPTING TO DO THIS HIS LEFT HAND SLIPPED OFF THE PIPE CAUSING HIM TO HIT THE TOP OF HIS FINGERS ON HIS LEFT HAND AGAINST THE ROUGH PART OF THE GUARD.

OPERATOR WAS HEADING EAST ON #10 DIKE UNLOADING UNIT WHEN SOFT MATERIAL GAVE WAY CAUSING PAN TO TURN OVER,SLOW TUMBLE LANDING ON ALL FOUR TIRES.OPERATOR WEARING SEAT BELT.

WHILE CUTTING RUBBER FOR WIPER ON BELT KNIFE SLIPPED OUT RIGHT LEG ABOVE KNEE.

WHEN HE KNOCKED ROLELR OUT OF A BOOM BASE, ROUND METAL PLATE FELL HITTING LEFT HAND CUTTING FINGER.

WHILE PLATING 5/8" CABLE, ONE OK THE WIRE WENT THROUGH HIS GLOVE INTO TOP LEFT HAND.

EMPLOYEE WENT OUT INTO BONE YARD AREA, LOOKING FOR A USED PART ON ONE OF THE OLD JUNK PICKUP, AFTER LOOKING INTO OLD PICKUP HE TURNED AND STARTED TO WALK AWAY. HIS FEET SLIPPED ON LOOSE GROUND , AS HE STARTED TO LOSE HIS BALANCE, HE EXTENDED HANDS OUT TO CUSHEN FALL. HIS LEFT HAND PALM STRUCK A PIECE OF OLD SCRAP METAL.

EMPLOYEE WENT OVER TO HEAD PULLEY (ON GROUND) TO REPOSITION CHAIN, SIGNALED CRANE OPERATOR TO BOOM DOWN. OPERATOR CABLED UP INSTEAD CAUSING HD PULLEY TO LIFT, WHIPPING AROUND, PULLEY SHAFT CAU GHT KNEE AND TWISTED HIS LEG.

STANDING ON LADDER IT SLID EMP FELL TO GROUND

EMPLOYEE WAS HELPING MECHANIC HOLDING THE ROD UP ON OPPOSITE SIDE OF EQUIPMENT WHILE BEING RAISED BY A JACK THE ROD JERKED FORWARD CAUSING EMPLOYEE TO LOOSEUP & THREW HIMSELF BALANCE CAUGHT HI MSELF FROM FALLING TO FLOOR & HAND HIT STEERING KNUCKLE THAT WAS ON THE FLOOR

EMPLOYEE WAS HOLDING A PIECE OF KEY STOCK 1 1/2" X24" ON A BUSHING WHILE BEING HIT WITH HAMMER BY ANOTHER EMPLOYEE. HE SLIPPED WITH KEY STOCK WHILE BEING HIT AND CUT FINGER ON STEEL OF 3 SP.R EDUCER.

EMPLOYEE WAS LOADING A STUFFING BOX FROM A PUMP INTO A PAYLOADER BUCKET,HE LOST CONTROL AND STUFFING BOX FELL ON LEFT FOOT.EMPLOYEE WAS WEARING STTEL TOE SAFETY SHOES.WEIGHT OF BOXX 800(#'S)

EMPLOYEE WAS LIFTING HAMMERS FROM CRUSHER THAT WERE BROKEN INTO A PAYLOADER BUCKET, APPROX. WEIGHT 190#, LIFTING TO MUCH WEIGHT BY HIMSELF DURING TIME OF LIFTING FELT SOMETHING PULL IN LOWER A BD. AREA.

EMPLOYEE WAS CHECKING SCREEN SHEETS ON #8 SCREEN AT THE SCREENHOUSE APPARENTLY LOST HIS BALANCE AND FELL INTO THE #6 CROSSBELT CHUTE, LANDING ON THE BELT ON HIS BACK, WITH HIS RIGHT LEG UNDER HIM - EMPLOYEE WAS NOT WEARING HIS SAFETY BELT, AS INSTRUCTED.

EMPLOYEE WAS WALKING UP AN INCLINE, OF STACKER CONVEYOR WITH 2-V-BELTS AND KEEDLED OVER AND FELL ON THE CAT WALK.

OPERATOR WAS DRIVING EMPTY HAULTRUCK HEADING SO ON HAULROAD WHEN ANOTHER HAULTRUCK HEADING NORTH LOADED STARTED COMING TOWARDS HIM HE WENT TO THE FAREST POINT OF THE SIDE OF THE ROAD TO AVOID A COLLISI0N BUT THE 2 HAVING UNITS CAME TOGETHERRT FRONT TO RIGHT FRONT SPINNING VEHICLE AROUND & STOPPED

EMPLOYEE WAS DRIVING HAUL UNIT LANDED TO PLANT ON THE N.P.T. HAUL RD, LEFT THE SIDE OF THE ROAD CROSSED TO OTHER SIDE APPROX. 85 FT TO OTHER SHOULDER TRAVELED 92 FT HIT BOULDER PROCESS 108 FT HIT 3SM DIRT MATERIAL MOODS CAUSING TRUCK TO TURN OVER ON ITSLEFTSIDE ROAD LONG AND STRAIGHT 60FT WIDE TOLD HIS SUPERVIOR THAT HE FELL ALSEEP. TAKEN TO LYKES HOSPTIAL THEN VIA AMBULANCE TAMPA

THE EMPLOYEE WAS STEAMCLEANING A 235 CATBACKHOE,WHEN THE BURNER ON THE STEAM CLEANER WENT OUT.HE CLIMBED UPON THE UNIT TO SEE WHY AND JUST AS HE WAS NEAR THE BURNER IT REIGNITED FLAME BURNED H IS RIGHT FOREARM.FIRST AID TREATED 06-22-88 MEDICAL TREATMENT AT THE HOSPITAL AND ADMITTED ON THE 23RD.

I NAME WAS GOING INTO THE CRUSHER CONTROL ROOM AND WHEN HE CLOSED THE DOOR HE CAUGHT HIS RIGHT FINGER TIP IN THE DOOR FROM AND AMPUTATED TIP.

EMPLOYEE WAS FILLING THE WATER TRUCK AT THE DIKE PUMP PIPELINE HE GOT ON THE PIPE TO TURN THE VALVE OFF AND SLIPPED OFF THE PIPE WHEN HE HIT THE GROUND HE STEPPED OR LANDED IN A HOLE AND BROKE HIS LEFT ANKLE.

RESTACKING TOP IDLERS AND DROPPED ON RT FOOT WEARING STEEL TOED SHOES

EMPLOYEE HAD JU8T FILLED 5-GAL CAN WITH GASOLI-NE AND SET IT UPON THE TRUCK BODY NEAR THE PONY MOTOR ON THE FUEL TRUCK SLIDCAN ABING BED A SPARK IGNITED THE GASOLINE FUMES, CAUSING EMPLOYEE TO JUMP BACK, SPI5LING GAS ON HANDS AND ARMS WHEN HE PULLED CAN FROM THE TRUCK BODY.

EMPLOYEE WAS OP9RATING 651-B SCRAPER AT THE NORTHPIT DUMP AREA OPERATING EMPTY WHEN THE HITCH BROKE RIGHT SIDE. EXCESS STRAIN PROBABLY CAUSED HITCH LINK TO BREAK ALSO LEFT SIDE AND TRACTOR NOS E DIVED INTO TH9 GROUND SOFT MANTRIP OPERATOR WAS WEARING MANDATERY SEATBELT.

EMPLOYEE WAS RE4OVING BOLT WHEN WRENCH SLIPPED GREASE ON HANDLE. HIT LEFT BAND ON JAGGED PIECE OF FRAME WHEN HE SLIPPED.

ELECTRICIAN HAD3PUT ON HIGH VOLTAGE GLOVES AND USED HOT STICK TO REMOVE OR PULL OUT THE FUSES.AFTER HE DID THIS,HE REMOVED HIS GOVES TO TEST OPEN FUSES WITH SIMPSON METER FOR CONTINUITY.AT THI S PERIOD A FLAS2 OCCURRED.ONE PIGTAIL ON THE FUSE HAD BLOWN,MADE CONTACT 2400V,CAUSING INSULTION BREAKDOWN.

EMP OPERATING 50 TON HAUL UNIT IN NO PIT, DRIVER FELL ASLEEP AND RODE UNIT APPROX 170 FT WITH LEFT TIRES ON SHOULDER OF ROAD. BEFORE HITTING PILE OF ROCKS AND MATERIAL FLIPPING UNIT ON ITS TOP OPERATOR WA8 WEARING A SEAT BELT

EMPL PULLING SC9EEN SHEET ON FRAME TO BE WELDED.FELT SOMETHING SNAP IN RIGHT ANKLE.

EMP WORKING DUM1 AREA N. PIT, AND BACKING DOZER UP WENT OFF 20' EMPBANKMENT, WEARING SEAT BELT

EMP DISMOUNTING3FROM HAULING UNIT LAST SLING STEP BROKE CAUSING EMPLOYEE TO FALL TO GROUND LANDING ON LEFT ARM

EMPLOYEE WAS CU7TING A PIECE OF CONVEYOR BELT FOR THE TALLGATE ON BOHINER 2 KNIFE CUT THRU BELT SUDDENLY AND WENT INTO RIGHT THIGH.

EMPLOYEE WAS IN8IDE THE BOHRINGER CRUSHER PERFROMING MAINTENANCE WORK AND WAS HCECKING THE ROLE BARS AND TRIED TO MOVE THEM FORWARD WITH HIS FEET AND SLIPPED AND FELL INSIDE THE CRUSHER STRIKI NG THE REAR OF 2IS HEAD ON THE STEEL STRUCTURE OF THE CRUSHER.

EMPLOYEE WAS RE4OVING A TRANSMISSION FROM THE PETTIBONE CRANE THE TRANSMISSION SLIPPED SIDEWAYS AND CAUGHT HIS LEFT HAND CAUSING LACERATIONS ON HIS PALM

CAST IRON LINER3PLATES WERE BEING INSTALLED IN THE FINISH MILL.THE INJURED EMPLOYEE WAS LEANING THROUGH AN OPENING TALKING WITH THE OTHER EMPLOYEE'S WHEN SEVERAL OF THE LINER PLATES DISLOGED S STRIKING INJURE8 EMPLOYEE IN THE FACE WITH MULITIFLETRAUMA.

EMPLOYEE WAS VE9TICAL WELDING USING GLASSES BUT DIDNT HAVE SIDE SLIELDS IN, CAUSING FLASH BURNS

PAN PULLING OUT3OF DUMPING AREA, SIGNALMAN HOT PAYING ATTENTION, DOZER BUMPED INTO BACK OF PAN, CAUSING IMPACT, JERKING OPERATOR CAUSING BACK STRAIN

651-B PAN WAS IN POSITION TO BE PUSHED BY THE PUSHCAT THE OPERATOR OF THE PUSHCAT PUSHED AND HIT THE PAN TO HARD JARRING THE OPERATOR AND THIS IN TURN CAUSED THE OPERATOR TO STRAIN HIS BAC K

EMP WAS ATTEMPTING TO REINSTALL GLASS INTO RUBBER GROMET (FACE OF SCALE) WHEN THE GLASS SHATTERED CUTTING HIS FINGER

EE WAS INSIDE A CONCRETE TRUCK USING AN AIR HAMMER TO LOOSEN MATERIALS THAT HAD ADHERED TO THE INSIDE. THE VIBRATION CAUSED A CHUNK OF CONCRETE TO LOOSEN & FALL ON THE EES NECK & BACK AREA.

EMPLOYEE WAS BOLTING DOWN BARREL RACK ON TOP OF THE PORTABLE STEAM CLEANER EMPLOYEE STARTED TO COME DOWN FROM UNIT STEPPING ON LADDER AND GRABBED THE HANDRAIL HANDRAIL BROKE AND EMPLOYEE HIT T HE BACK OF HIS HEAD ON THE HITCH LANDING ON THE CONCRETE FLOOR OF THE SHOP

EMPLOYEE, A SHOVEL OPERATOR WAS ATTEMPTING TO INSTALL A SPRING ON THE CABLE TRIP CONTROL HIS HAND SLIPPED OFF THE SCREWDRIVER THAT HE WAS USING AND HIS HAND WENT INTO THE CABLE SPOOL OR GEAR.

EMPLOYEE HAD BEEN WASHING UP WITH A HOSE ANDGOT WET, WENT TO THE OPERATORS HOUSE WHERE A FUEL FIRE WAS BURNING HE ATTEMPTED TO ADD MORE FUEL OIL AND THE FIRE, FLAMES ERRUPTED AND THEN HE PANIC ED AND STARTED THROWING WATER ON THE FLAMES. (THIS ISA STEEL THREE SIDED BUILDING THE WATER CAUSED STEAM AND HE RECEIVED 2 DEGREE BURNS ON THE FACE AND FOREARM.

EMP DRIVING GROUND ROD NEAR A ELEC JUNCTION BOX AND HIT LEFT HAND ON THE BOX MISSED ROD WHILE DRIVING

EMP WAS USING HAND SANDER ON METAL PLAE ON THE FLOOR SANDER CAUGHT EDGE OF PLATE KICKING BACK STRIKING LEFT KNEE NEAR KNEE CAP

EMPLOYEE HAD BEEN CHECKING SHORT CONVEYORS AND CHUTES ANDWAS COMING DOWN 4 FOOT EXIT LADDER, HAND RAIL BROKEN CAUSING EMPLOYEE TO FALL 4 FT ON TO THE STAIRWAY.

EMPLOYEE CUTTING CONVEYOR WITH JACKKNIFE IT FOLDED AND HE CUT MIDDLE FINGER AND TOP LEFT HAND REQUIRED SEVERAL SUTURES

EMP WAS CLEANING HAULING UNIT BODY OUT WITH PAYLOADER ROCK CAME OUT OF BODY JUMPED OVER BUCKET PAND WENT THROUGH WINDSHIELD OF LOADER CUT INDEX GINGER ON LEFT HAND. WINDSHIELD IN LOADER BROKE, THIS IS WHAT CUT EMPLOYEE

EMPLOYEE WAS INSTALLING SPD. REDUCER AT THE PLT THE SPD REDUCER SLIPPED OFF SHAFT AND CAUGHT EMPLOYEES RIGHT RING FINGER BETWEEN SPD REDUCER AND ANGLE IRON

USING PIPE WRENCH WORKING ON PUMP SHAFT,WRENCH SLIPPED HIT LITTLE FINGER ON STELEL PIPE CASING.

EMP OPERATING PAN SOUTH PIT AREA WEARING SEAT BELT OPERATING ON ROUGH TERRIAN CLAIMS CONDIDTIONS CAUSED BACK INJURY

EMPLOYEE CHANGING DRILL STEM STEM MOVED AND HIT MAST EMPLOYEE HAD LEFT HAND HOLDING STEM HIT HAND ON MAST BREAKING FINGER LEFT HAND