IMI Stony Creek Stone Co: 162 MSHA citations Metal/Non-Metal

While using torch to remove and replace shaker screen, a piece of debris hit the employee's hard hat and fell behind cutting PPE. Employee was taken for evaluation at medical facility and returned to work with no restrictions.

Employee was scraping drive and hit frozen material. Employee was thrown forward and hit steering wheel. Employee had lap belt on during time of accident. Employee did not report injury to IMI till 12/10/2018.

Miner was climbing out of a transfer box on aggregate plant when their knee twisted.

While adjusting the door on secondary crusher, the door fell open and crushed the miner's thumb. Two people were trying to adjust the door when it fell. The door fell open smashing the thumb against a conveyor structure.

EE was working on East Pump and using right hand to put test cover on incoming power, when power flashed back and burned his right hand.

A stray rock apparently left the shot and struck a visitor on his left leg, while he was sitting inside a pick-up.

Workers were gathering materials for a job & moving from bin #2 to the tower. One was driving a flat bed service truck & 1 was in the passenger seat. Injured was seated on the rear of the flat bed. As the truck moved thru the yard it hit a bump & ee bounce up and back down on the bed of the truck causing pain in his buttocks, hip, tailbone, & broke the skin behind his right knee.

EE was helping other ee change screens all the plant. He lost his footing causing him to slip and hit bump into a motor mount with his back.

EE IS A MECHANIC AND WAS WORKING ON A TAILGATE OF A HAULING UNIT AT STONEY CREEK. HE WAS WORKING UNDER IT AS WELL AS ALL AROUND. HE WAS WEARING SAFETY GLASSES. AT SOME POINT METAL FLEW BEHIND THE GLASSES INTO HIS LEFT EYE CAUSING IRRITATION. IT GREW MORE IRRITATED AS TIME WENT ON.

During morning clean-up, ee entered a feed box to clean out material build up. As he kicked material, it broke free causing him to twist his back and fall. As he fell he stradled the inner wall.

EE WAS IN THE SHOP. AN EXTENSION CORD WAS HANGING ON A HOOK ATTACHED TO A SHELF. THE CORD WAS NOT IN USE. ONE LOOP OF THE CORD HAD FALLEN TO THE FLOOR. EE REACHED FOR A SCRAPER & STEPPED INSID E THE LOOP OF THE EXTENSION CORD WITH HIS RIGHT FOOT. HE BECAME ENTANGLED, LOST HIS BALANCE & FELL BACK, REACHING BEHIND W/HIS RIGHT HAND TO CATCH HIMSELF, HE FELL & BROKE HIS RIGHT WRIST.

EE WAS CUTTING A PIECE OF METAL WITH CUTTING TORCH. HE FINISHED HIS CUT AND TURNED TO SHUT HIS TORCH OFF, WHEN A PIECE OF SLAG POPPED OFF THE COOLING METAL AND FLIPPED INTO HIS RIGHT EYE BEHIND HIS SAFETY GLASSES.

THE GROUND WAS FROZEN AND SNOW COVERED. EE WAS HELPING REMOVE CONCRETE BLANKETS FROM CONCRETE - GETTING READY TO REMOVE CONCRETE FORMS. HE STEPPED INTO A FROZEN RUT AND TWISTED HIS LEFT ANKLE.

EE WAS BACKING HAULING UNIT UP TODUMP MATERIAL OVER EDGE OF STOCKPILE. REAR TIRES WENT OVER EDGECAUSING HAULING UNIT TO FALL TO THE RIGHT SIDE AND ROLL DOWN STOCKPILE AND LAND ON ITS WHEELS. MR.BALL RECEIVED LACERATION TO HEAD AND CONCUSSION TO HEAD AND BRUISES TO BODY.

EE WAS CLIMBING DOWN THE LADDER OF A FRONT END LOADER. THE LADDER WAS WET FROM RAIN. HIS FOOT SLIPPED ON A WET LADDER RUNG AND HE TWISTED HIS RIGHT KNEE TRYING TO CATCH HIMSELF FROM FALLING.

EE CLIMBED UP ON THE CRUSHER TO REACH AND CLEAN A CAMERA LENSE. AS HE WAS DESENDING, HE STEPPED ON TO THE MOTOR AND JUMPED DOWN ON TO THE DECK, TWISTING HIS LEFT KNEE.

8-8-01-OVER 90 DEGREE HEAT. EE WAS UP ON TOP OF PLANT GREASING. HE BECAME ILL-VOMITING-=WAS NOT SWEATING-CLIMBED DOWN OFF PLANT AND CONTACTED HIS SUPERVISOR. EE WAS TAKEN TO HOSPITAL AND TREAT ED FOR HEAT EXHAUSTION-THEN RELEASED AFTER 1500 THE SAME DAY.

EMPLOYEE WAS WELDING ON A SCREEN USING SCALER TO CLEAN SLAG AND WELD. HE HAD SAFETY GLASSES ON AND WAS PREPARING WELD AREA. A PIECE OF MATERIAL WAS BLOWN IN BEHIND HIS GLASSES BY THE WIND. HE WENT TO EYE AREA, BRUSHED IT AWAY, THOUGHT IT WAS GONE. THE NEXT EVENING HIS EYE STARTED TO BECOME IRRITATED. WENT TO DOCTOR AND PRESCRIPTION WAS GIVEN.

JACKING ANGLE IN PLACE USING AN EXTENTION POST. PUT PRESSURE ON JACK AND JACK KREELED OUT STRIKING IN HEAD CUTTING HIS EYEBROW AND OPENING UP A WOUND THAT REQUIRED STITCHES.

EMPLOYEE WAS MOVING A CRUSHER PIECE AROUND IN THE SHOP. HE PICKED THE PIECE UP WITH HIS ARMS AND STARTED WALKING. HE FELT A SHARP PAIN IN HIS BACK. HE DIDN'T SAY ANYTHING UNTIL TUESDAY THE 13T H OF FEBRUARY. WENT TO DOCTOR ON WEDNESDAY. DR. GAVE HIM MEDICINE FOR A PULLED MUSCLE. EMPLOYEE WENT TO WORK ON MONDAY 2-19-96.

EE WAS GREASING THE MOBILE EQUIPMENT THE PREUMATIC GREASE GUN WAS EMPTY EE WAS CHANGING THE GREASE GUN OVER A NEW PAIL OF GREASE EE WAS USING A SCREWDRIVER TO TAKE THE LID OFF OF THE PAIL THE SCREWDRIVER SLIPPED & HIS FINGER WAS CUT ON THE LID

EMPLOYEE WAS CLEANING STONE OFF OF A CRUSHER PLATFORM. APPROX 20' BELOW A SCREENING TOWER THE SCREEN HAD PLUGGED . A ROCK APPROX. 2 1/2 ROUND HIIT EMPLOYEE IN THE HARD HAT CAUSING HIS NECK TO FLEX. THE DOCTOR SAID HIS NECK HAD BEEN SPRAINED

EE & EE WERE REMOVING A 4IN PIPE OT OF A 12IN CONCRETE WALL EE WAS HOLDING A PUNCH EE WAS HITTING IT W/A 8LB SLEDGE HAMMER TO DRIVE THE PIPE OUT OF THE WALL EE MISSED PUNCH & HIT EE RT THUMB

EE WAS STANDING IN BED OF SERVICE TRUCK. HE BENT OVER TO PICK UP A TRANS CARRIER ASSEMLY AND TURNED TO PLACE ASSEMBLY ON A SKID, INJURING HIS LOWER BACK.

EE WAS CLEANING DIRT FROM A FRONT END LOADER TO GET TO A BOLT. HE WAS USING A 2 LB HAMMER AND PUNCH TO FREE THE HARDENEND MUD AROUND THE BOLT. HE HIT HIS LEFT HAND INSTEAD OF THE PUNCH. THIS C AUSED THE INJURY.

EE WAS WORKING OUTSIDE CLEANING OUT A CHUTE. A PIECE OF RUSTY SCALE BLEW INTO HIS LEFT EYE. THE WIND WAS VERY STRONG THAT DAY. EE SAID IT DIDN'T BOTHER HIM UNTIL THE NEXT MORNING.

I.NAME CLEANING AROUND 7' CRUSHER PLATFORM. WHEN FINISHED,STARTED WALKING DOWN STAIRS,MISSED BOTTOM STEP AND FELL ON PLATFORM. HIT RIGHT HAND DURING THE FALL CAUSING THE SPRAIN.

DRIVING HAUL UNIT HIT BUMP AS HE WAS TURNING PULLED MUSCLE IN BACK

GAS SPLASHED IN R EYE LOADING CAN IN TRUCK

LOOSENING BOLTS ON TRUCK TO CHANGE REAR AXLES PULLED ON WRENCH BACK WENT OUT OF PLACE

I NAME WAS OPERATING A 7IN DISC GRINDER GRINDING WHEEL CAUGHT THE EDGE OF THE STEEL PIPE & TWISTED HIS LEFT ARM

EE WAS FILLING THE AIR SYSTEM ON A 631 HAULING UNIT. HE SHUT THE AIR VALVE, REMOVED THE PLUG AND FILLED THE RESERVIOR WITH ALCOHOL. HE TURNED THE VALVE ON WITHOUT THE PLUG AND BLEW ALCOHAL IN HIS LEFT EYE.

EE WAS STOCKPILING MATERIAL, HE HIT A BUMP FROM THEN ON HIS BACK HURT. THE PAIN WAS BAD ON SATURDAY BUT IT DID EASE UP. MONDAY MONRING OTHER DECIDED TO HAVE HE TAKEN TO HOSPITAL AND HAVE X RAY S RAN.

EE WAS HOLDING A PUNCH WITH HIS LEFT HAND. OTHER WAS HITTING THE PUNCH WITH A SLEDGE HAMMER. HE MISSED, THE PUNCH HIT EE MIDDLE FINGER ON HIS LEFT HAND.

HE WAS RAISING HIMSELF IN THE MANLIFT. HE WAS LOOKING TO THE LEFT WHEN HIS RIGHT ARM GOT CAUGHT BETWEEN THE MANLIFT FRAME AND A 21" I BEAM. AT HIS TIME HE SHUT HTE MACHINE OFF, UNTIL HELP AR RIVED WHICH WAS IMMEDIATELY.

DIGGING OUT FEEDER,ROUND TANK.PULLING ROCK OUT ,FOOT SLIPPED CAUSING SOMETHING TO PULL IN HIS SIDE.

CHANGING HYDRAULIC CYLINDER HOSE,CYLINDER ROLLED ONTO HAND -LACERATION REQUIRING STITCHES.

STEPPING DOWN OFF STEEL CASTING.FOOT SLIPPED AND HE HIT RIGHT HAND ON PIECE OF STEEL.IT BROKE RIGHT WRIST.

EMPL WAS PLACING SHUTE IN FRONT OF SCRREN WHEN SCREEN FELL. IT THEN CAUGHT FINGER HE THEN PULLED FINGER OUT. IT PINCHED FINGER & RIPPED SKIN OFF BOTTOM OF FINGER.

A CABLE CLEVIS WAS DROPPED FROM ON TOP OF SHOVEL WHEN VICTIM WALKED FROM UNDERNEATH THE SHOVEL VICTIM RECEIVED STITCHES TO HEAD LACERATIONS.

USING A HAMMER PUNCH SMASHING FINGER WITH HAMMER.HE WAS INSTALLING A PIN AT THE TIME.FINGERNAIL HAD TO BE REMOVED AND TWO STITCHES PUT IN.

TIGHTENING BOLT8 ON NEW PLANT CONTRUCTION, STRAINING LOWER BACK.

UNLOADING BRAKE3BANDS FROM FRONT END LOADER BUCKET ONTO POWER SHOVEL FOR LATER INSTLALLATION IN POWER SHOVEL. EMPLOYEE WAS STANDING ON BOOM OF POWER SHOVEL, STARTED RAINING, EMPLOYEE SLIPPED A PPROX. 12 FEET.3

INSTALLING RETU9N IDLER ON BELT CONVEYOR.

LIFTING CONVEYO9 ROLLERS FROM OVERHEAD TO FLOOR BACK SPRAIN.

SMALL SLIVER OF3STEEL FROM CUTTING & GRINDING INFECTION OF RIGHT KNEE.

A 3/4" EYE BOLT WAS USED IN LIFTING A SECTION OF STEEL BIN WITH CHAIN FALLS FOR PAINTING OF BIN, EYE BOLT LOOKED GOOD AND BIN SECTION WAS LESS THAN 1000 POUNDS IN WEIGHT, NO CLEAR REASON FOR B OLT TO BREAK