Mine No 108I Coal

Employee was in a standing position blocking roof bolts when a piece of rock 3'x1 1/2'x6" fell from the top striking him on the side of his left leg.

Employee was walking to get a timber when a peice of rock 3'x5'x1' x 0 fell from the roof striking him on his left shoulder, back and left leg. Employee continued to work light duty until 10/25/2005, the date of his operation.

EE was attempting to lift high voltage cable into a sled when he began having trouble seeing out of his right eye.

Intake entry at #2 block along #2 belt between stations #58 and #64. Fall was 70' long, 18' wide and 4 1/2' high.

Belt entry in #1 block, 150' from portal, fall was 60' long, 18' wide and 5' high.

EMPLOYEE WAS USING A PICK HAMMER TO OPEN ON A BELT SPLICE. HE USED A SECOND HAMMER TO DRIVE THE TIP OF THE HAMMER INTO THE CLIP, WHEN A PIECE OF THE HAMMER BROKE OFF & LODGED IN HIS LEFT WRIST.

Employee was walking around #4 belt tail piece when he tripped over the anchor pin or turnbuckle causingm him to fall to the mine floor causing pain in his back. Employee quit working as of March 29, 2005.

Employee broke a drill steel off in the top, leaving approximately 8 inches of the steel handing out. After drilling another hole for the roof bolt, he caught his left index finger between the roof plate and the broken drill steel while installing a roof bolt.

ROOF FALL IN #6 ENTRY OF NE MAINS ON BELT ONE BLOCK INBY SPAD #1711. FALL WAS 38'LONG X 18'WIDE X 5'HIGH. FALL WAS DISCOVERED BY FIREBOSS PRIOR TO WORKING ON SUNDAY NIGHT.

EE WAS TRAVELING THE RETURN AIR COURSE, A ROOF FALL WAS ENCOUNTERED. IT WAS LOCATED IN THE INTERSECTION OF #1 ENTRY OF NORTHEAST MAINS IN THE REDSTONE SEAM SPAD #1727. IT WAS APPROX. 18'WIDE , 30'LONG, AND AT LEAST 6'HIGH. NO INJURIES.

EE WAS STANDING IN THE INTERSECTION AS THE SCOOP WAS TRAMMING OUTBY WHEN THE SCOOP SLID INTO A HOLE IN THE ROADWAY & CAUGHT HIS RT.FOOT BETWEEN SCOOP BUCKET & ROADWAY PAVEMENT.

FALLS IN BLEEDER ENTRIES OF BARRIER BETWEEN TOP END OF 7 LEFT OFF 1 RIGHT AND 6 LEFT OFF 1 RIGHT SECTION.

EE WAS HELPING UNROLL A 700' ROLL OF MINER CABLE THAT WAS SUPPORTED WITH A 5' PIECE OF PIPE LOCATED BETWEEN THE FORKS OF A FORK LIFT. THE PIPE FELL OFF THE FORK CAUSING THE SPOOL TO FALL AGAI NST THE LEFT FORK WHERE EE'S RIGHT INDEX FINGER WAS LOCATED.

EE WAS ASSISTING THE CREW IN THE CHANGING OF THE GEARCASE ON THE JOY 14CM10 CONTINUOUS MINER WITH REMOTE IN THE #5 ENTRY, SPAD #1722, OF EAST MAINS WHEN HIS RIGHT FOOT WAS PINCHED BETWEEN THE RIPPERVEYOR SPROCKET AND GEARCASE OF THE MINER, RESULTING IN TWO BROKEN BONES IN HIS RIGHT FOOT.

WHILE MAKING THE WEEKLY EXAM OF THE BLEEDER ENTRY IN BLEEDER ENTRY IN 5 LEFT OFF 1RIGHT, A ROOF FALL WAS ENCOUNTERED IN #1, #2, AND #3 INTERSECTION NEAR STATION #1532. APPROXIMATE LENGTH: 125' , WIDTH: 18' AND HEIGHT: 6'.

EE WAS SWINGING A BOLTER WRENCH WITH HIS RIGHT HAND STRIKING AGAINST A PLUGGED UP BOLTER STEEL, WHEN IT GLANCED OFF AND HE STRUCK HIMSELF WITH A WRENCH ABOVE HIS RIGHT EYE.

WHILE MAKING A PRE-SHIFT EXAMINATION FOR 3RD SHIFT, A ROOF FALL ON THE HAULAGE ROAD WAS FOUND. IT WAS LOCATED 2500 FEET FROM THE OUTSIDE AND 2700 FEET OUTBY THE WORKING SECTION IN #7 ENTRY AT SPAD #493. IT WAS 25'LONG, 18'WIDE, AND 2'- 7' IN HEIGHT ABOVE THE COAL SEAM.

A ROOF FALL OCCURRED DURING MINING IN THE 5-LEFT WORKING SECTION WHILE CONNECTING THE XCUT BETWEEN NO. 7 AND NO. 8 ENTRIES. THE ROOF FALL RODE BACK THROUGH THE INSTALLED ROOF BOLTS, STRIKING T HE REMOTE CONTROLLED CONTINUOUS MINER OPERATOR AND MINER HELPE. THE MINER OPERATOR SUSTAINED SERIOUS PERSONAL INJURIES WHILE THE MINER HELPER SUSTAINED FATAL INJURIES.

EE WAS TRAVELING TO THE OUTSIDE AT THE END OF HIS SHIFT ON A JEEP, WHEN A ROCK FELL FROM THE ROOF STRIKING HIS RIGHT HAND AND CAUSING A LACERATION. THE ACCIDENT OCCURRED WITHIN 100' FROM THE O UTSIDE. HIS RIGHT HAND HAD TENDON AND NERVE DAMAGE REQUIRING CORRECTIVE SURGERY.

A ROOF FALL MEASURING 50' W X 22' L X 15' H WAS DISCOVERED BY THE SECTION FOREMAN ON THE 4 LEFT SECTION (001-0). IT WAS JUST OUTBY STATION 1382 IN THE #5 BELT ENTRY. IT WAS IN AN INTERSECTION AND EXTENDED INTO THE ADJOINING X-CUTS. THE ARE WAS DANGER OFF AND POSTS WERE SET.

THE FALL WAS DISCOVERED WHENTHE CONVEYOR BELT QUIT RUNNING AND THE MINE FOREMAN WENT TO INVESTIGATE. IT IS 1 BLOCK INBY STATION 558 IN THE 35 ENTRY. IT MEASURES 8'HX16'WX25'L.

A FALL IN THE #4 ENTRY ALONG #5 BELT WAS DISCOVERED BY THE PRE-SHIFT EXAMINER. HE ALSO FOUND A FALL IN THE BELT ENTRY ADJACENT, TO THE 1ST FALL. BOTH FALLS ARE APPROXIMATELY8'HIGH X 20'LX18' W. THEY ARE OUTBY 1 BLOCK FROM SPADS 1152 AND #1153. BOTH FALLS HAVE BEEN POSTED OFF, DANGERED OFF AND ABANDONED.

A FALL IN THE #4 ENTRY ALONG #3 BELT WAS DISCOVERED BY THE PRE-SHIFT EXAMINER. HE ALSO FOUND A FALL IN THE BELT ENTRY ADJACENT, TO THE 1ST FALL. BOTH FALLS ARE APPROX 8'HX20'LX18'W. THEY AR EA OUTBY 1 BLOCK FROM SPADS #1152 AND #1153. BOTH FALLS HAVE BEEN POSTED OFF, DANGERED OFF AND ABANDANED.

THE EE WAS CHANGING INTO HIS WORK CLOTHES. WHILE PULLING HIS MINE BELT OUT OF HIS LOCKER, A CLAW HAMMER FELL AND STRUCK HIM ON THE FOOT. THE HAMMER FELL ABOUT 3 FT. HE WAS IN HIS STOCKING FEET WHEN STRUCK.

EE HAD JUST INSTALLED A BOLT IN HIGH AREA USING A LONG BOLT WRENCH TO TIGHTEN IT WHEN THE DRILL HEAD WAS LOWERED IT RUBBED AGAINST THE CANOPY JACK CAUSING THE HEAD TO MOVE ABRUTLY. THE WRENC H IN THE DRILL HEAD STRUCK EE ON THE BILL OF HISHARD HAT, DRIVING IT AGAINST HIS SAFETY GLASSES THE IMPACT AGAINST THE GLASSES CAUSED A CUT ON HIS EYELID

EE WAS REPLACING A TOP ROLLER IN THE #2 CONVEYOR BELT. HE WAS STRAINING TO LIFT THE ROLLER INTO PLACE AND SUFFERED A COMPRESSION FRACTURE TO HIS 1ST VERTABRAE IN HIS LUMBAR SPINE. "THIS ACCIDE NT WAS NOT REPORTABLE UNTIL 3/13/00".

EE WAS CARRYING A CAN OF HYDRAULIC OIL TOWARD THE FACE. HE WAS WALKING IN A MUD HOLE AND TWISTED HIS KNEE.

THE EMPLOYEE WAS RIDING IN THE SECTION MANTRIP, TAVELING TOWARD THE OUTSIDE. A BELT ROPE WAS ATTACHED TO THE REAR OF THE MANTRIP. HE TURNED AROUND TO LOOK AT THE ROPE. HIS LEFT ARM AND 3 FINGERS ON HIS RIGHT HAND WERE CAUGHT BETWEEN THE MANTRIP AND COAL RIB.

THE EMPLOYEE WAS LIFTING A GARAGE DOOR AT THE MINE REPAIR SHOP. THE DOOR WAS HARD TO GET UP. HE FELT PAIN IN HIS LOWER BACK.

EMPLOYEE WAS OPERATING THE SECTION MANTRIP, TRAVELING TO THE OUTSIDE AT THE END OF SHIFT. THE FRONT TIRES OF THE MANTRIP STUCK A RUT IN THE ROAD, CAUSING THE STEERING WHEEL TO SPIN. THE EMPLOYEE'S HAND WAS BETWEEN THE SPOKES OF THE STEERING WHEEL AND WAS STRUCK BY THE SPINNING STEERING WHEEL.

INJURED WAS BENT OVER WITH WATER HOSE WASHING OUT TAIL ROLLER. HIS FOOT SLIPPED CAUSING HIM TO TWIST AROUND. HIS BACK STARTED HURTING.

WALKING UP #2 BELT RAW HEAD INTO OVERCAST GOING ACROSS BELT.

INJURED PERSON WAS HELPING PUT BELTS ON FAN ON THE SURFACE, WHILE DOING THIS HE WAS PULLING ON BELTS AND HIS BACK STARTED HURTING.

ROCK FALL IN #7 ENTRY 1 CROSS CUT INBY SPAD 255.

INJ WAS LOADING SUPPLIES ON SCOOP WHILE TRYING TO MOVE ROOF BOLTS OFF TOP OF PLATES HE TWISTED HIS BACK

EE WAS IN A KNEELING POSITION WIRING A PUMP AT AN OUTSIDE PUMP HOUSE. HE STARTED TO STAND AND LOST HIS BALANCE. CAUGHT HIS TOE IN A CRACK BETWEEN BOARDS IN THE FLOOR, WHICH CAUSED HIM TO TWIST HIS KNEE. THIS ACCIDENT WAS NOT REPORTABLE UNTIL 10-8-99.

BELT ROLLER FELL OFF BELT ROPE HITTING EMPLOYEE ON TOP OF KNEE CAP WHILE PUTTING STRUCTURE IN BELT.

ROOF FALL IN INTERSECTION 18' WIDE 18' LONG 7' HIGH NO INJURIES.

INJURED WAS PULLING BELT TOGETHER WITH COMEALONG & BELT CLAMP. THE CLAMP SLIPPED OFF BELT HITTING HIM IN THE FACE.

INJURED WAS LIFTING A ROLL OF BRATTICE CURTAIN STARTED TO PUT UPON SHOULDER BACK STARTED TO HURT.

INJURED WAS MOVING MINER CABLE PULLED SOMETHING IN UPPER BACK.

TIGHTEN UP BOLT ON LEVEL WIND ON STD SHUTTLE CAR.WRENCH SLIPPED OFF BOLT CAUSING FINGER TO HIT LEVEL WIND

WAS PUTTING LID ON PANEL BOARD ON MINER, WHILE LIFTING LID, HE PULLED MUSCLE IN CHEST.

INJ MAN WAS TRAMING SHUTTLE CAR TOWARD FACE WHENCAR WENT THROUGH DIP IN BOTTOM HE BOUNCED UP STRIKING HEAD ON CANOPY

STRAINED BACK WHILE LIFTING.

INJURED WAS DOWN ON HIS KNEES WHEN HE STARTED TO GET UP HE HEARED A POP IN HIS KNEE AND IT STARTED HURTING.

INJURED PERSON WAS STANDING BESIDE MINER WHILE LOADING COAL. A SMALL ROCK CAME OUT OF MINER HITTING HIM ON RIGHT LEG.

DRAGGING MINER CABLE WITH LEG. FELT PAIN IN GROIN AREA.

CUTTING TOP FOR EQUIPT TO CLEAR. ROCK FELL OUT OF ROOF AT ATRS ON FLETCHER BOLTER, STRIKING EMP ON HEAD, KNOCKING HIM DOWN.

7 ENTRY THE MAIN MINE FAN ENTRY CANOPY TOP ON THE SURFACE COUAPSED FOLLOWING A HIGHWALL DISLODGEMENT. RESULTING IN HOLE IN THE CANOPY TOP APPROX 20'WIDE BY 12' LONG CAUSING AIR TO SHORT CIRCUI T TO THE OUTSIDE.

THE EMPLOYEE WAS CARRYING ONE END OF A CROSS BAR, WHEN HE LOST HIS FOOTING AND FELL, STILL HOLDING ONE END OF THE CROSS BAR. HE TWISTED HIS LOWER BACK CAUSING A SPRAIN/STRAIN.

THE EMPLOYEE WAS STANDING ON THE SCRUBBER RAIL OF THE 14CM-1 5 CONTINUOUS MINER ATTEMPTING TO REMOVE A ROCK FROM THE TOP OF THE MINER WHEN HIS FOOT SLIPPED CAUSING HIM TO FALL TO THE MINE FLOO R

THE EE WAS BENT OVER CUTTING A PIECE OF 2INCH BLACK PLASTIC IN TWO WITH A UTILITY KNIFE. AS THE KNIFE CUT THRU THE PIPE IT CONTACTED HIS LEFT THUMB.

THE EMPLOYEE WAS IN AN UPRIGHT POSITION TAKING A SHOWER. THE WATER SHE WAS SHOWERING IN BECAME HOT AND SHE JUMPED BACK, SLIPPED AND FELL TO THE FLOOR.

EMPLOYEE WAS STANDING BESIDE A MINE POST VISUALLY EXAMINING THE ROOF AND RIBS WHEN A PIECE OF THE RIB BROKE LOOSE, DISLODGING THE MINE POST WHICH STRUCK HIM IN THE UPPER RIGHT ARM.

EE WAS IN A STANIDNG POSITION REUTRNING THE WINCH CABLE AND HOOK TO THE SCOOP. AS HE PLACED THE CABLE AND HOOK ONTO THE SCOOP HE WAS STUCK ON THE BACK OF THE LEFT HAND BY THE HOOK.

THE 14 CM-15 REMOTE CONTROL MINER WAS BEING USED TO PILLAR RETREAT MINE IN THE 2 BLOCK OF 1 LEFT PANEL IN THE REDSTONE SEAM. AS THE CONTINUOUS MINER OPERATOR LOADED THE LAST SHUTTLE CAR FROM T HE PUSH OUT AND STARTED TO BACK THE MINER OUT, THE ROOF BEGAN TO WORK AND FELL ON THE HEAD OF THE CONTINUOUS MINER PREVENTING FURTHER MOVEMENT. FELL APPROX. 7 FT HIGH. THERE WAS NO INJURIES T

THE EMPLOYEE WAS STANDING UPRIGHT STACKING DOWTY CRADLE ROLLERS. AS HE WAS LAYING A PIECE OF STRUCTURE ON THE STACK, HIS FINGER WAS CAUGHT BETWEEN THE TWO PIECES OF BELT STRUTURE.

THE EE WAS IN AN UPRIGHT POSITION OBSERVING THE MINE ROOF AND THE ROOF BOLTERS WORK WHEN A PIECE OF ROCK FELL FROM THE MINE ROOF BETWEEN THE ROOF BOLTS AND STRUCK HIM ON THE HEAD AND KNOCKING HIM TO THE MINE FLOOR.

EMPLOYEE WAS IN AN UPRIGHT POSITION ROOF BOLTING ON THE RT SIDE OF THE ROOF BOLTER HE RAISED THE DRILL STEEL AGAINST THE ROOF & BEGAN TO ROTATE IT A PIECE OF ROCK FELL FROM THE ROOF HE WAS DRI LLING & STRUCK HIM ON THE HAND

EMPLOYEE WAS OPERATING SHUTTLE CAR FROM MINER TO DUMPING POINT WHEN HE GOT A SMALL PIECE OF COAL IN HIS EYE

AN UNTENTIONAL ROOF FALL OCCURED IN THE INTAKE ESCAPEWAY MESURING 16' LONG X 16' WIDE AND APPROX 7' HIGH IN #9 ENTRY. #8 ENTRY HAD A PREVIOUS FALL IN IT MEASURING 30' LONG X 16' WIDE AND APPR XO 15' HIGH. NO PERSONEL INJURED OR EQUIPMENT COVERED #8 ENTRY WILL BE CLEANED, CRIBBED, CANOPIED WITH STEEL BEAMS AND CRIBBED TO MINE ROOF.

EMPLOYEE WAS WALKING ALONGSIDE SECTION POWER CENTER WHEN HE STEPPED ON CABLES, WHICH WERE LYING ON THE MINE FLOOR, CAUSING HIM TO TWIST HIS BACK AND FALL.

AN UNINTENTIONAL ROOF FALL WAS DISCOVERED BY THE PRE-SHIFT EXAMINER ON 12-19-93. THE FALL MEASURED APPROXIMATELY 58 FEET LONG, 16 FEET WIDE, & 5 TO 8 FEET ABOVE THE COAL SEAM. AREA HAD BEEN SU PPORTED WITH 5 AND 6 FOOT ROOF BOLTS. THERE WERENO INJURIES TO EMPLOYEES OR EQUIPMENT. NO INTERRUPTION TO VENTILATION.

THE EE WAS IN A STANDING POSITION RAISING THE BOOM OF THE BOLTER. AS THE BOOM WAS RAISING HE REACHED FOR THE BOLT WRENCH THAT WAS LAYING ON THE DRILL BOOM. HIS FINGER BECAME CAUGHT BETWEEN THE WRENCH AND THE CANOPY JACK AND MASHED THE TIP OF HIS FINGER.

EMPLOYEE WAS ATTEMPTING TO REMOVE A FOULED DRILL STEEL FROM THE ROOF BY ROTATING THE DRILL STEEL & PUTTING DOWNWARD WITH HIS RT HAND WHEN HIS GLOVE CAUGHT ON THE DRILL STEEL & TWISTED HIS HAND ACCIDENT OCCURRED IN PITTSBURGH SEAM 002-0- SECTION

THE EMPLOYEE WAS IN A STANDING POSITION PULLING AND HANGING TRAILING CABLES FOR FACE EQUIPMENT.

EMPLOYEE WAS IN A STANDING POSITION OPERATING A REMOTE CONTROL MINER A ROCK MEASURING 10IN THICK X24IN WIDE X48IN LONG IDLODGED FROM THE MINE ROOF & STRUCK HIM ON THE HEAD & SHOULDER THIS RESU LTED IN A MIS ALIGNMENT OF HIS CERVICAL SPINE HEWAS UNDER SUPPORTED TOP

EE WAS IN A STANDING POSITION OPERATING A FLETCHER ROOF BOLTER, WHEN SHE LOWERED THE DRILL HEAD TO THE MINE FLOOR, HER RIGHT FOOT WAS CAUGHT BETWEEN THE DRILL HEAD AND THE MINE FLOOR. THIS CAU SED CONTUSIONS TO HER RIGHT FOOT.

THE EMPLOYEE WAS ROOF BOLTING A ROOF FALL CAVITY. WHILE HE WAS DRILLING A HOLE, HE WAS LOOKING UP AT THE TOP. A ROCK "ABOUT THE SIZE OF HIS FIST" FELL AND STRUCK HIM ON THE MOUTH AND LEFT CHEE K, CAUSING CONTUSIONS AND LACERATIONS.

AN UNINTENTIONAL ROOF FALL OCCURRED IN #8 AND #9 ENTRY AT STATION #503 MEASURING APPROX. 8' HIGH, 17" WIDE X 80' LONG. THE FALL OBSTRUCTED THE ESCAPEWAY BUT WAS NOT IMPASSABLE. THE FALL DID NO T AFFECT VENTILATION TO THE WORKING SECTION. THERE WERE NOT ANY INJURIES TO PERSONNEL OR EQUIPMENT. THE FALL WILL BE CLEANED UP AND THE ESCAPEWAY RE-ESTABLISHED.

THE EE WAS IN A SEATED POSITION IN THE HYDRAULIC AND MOTOR COMPARTMENT OF A SCOOP. HE DROPPED A BOLT. AS HE MANEUVERED HIS BODY TO PICK IT UP, HE TWISTED HIS KNEE AND SPRAINED IT.

DURING THE NORMAL MINING CYCLE ON THE 001-0 SECTION, THE CONTINUOUS MINER CUT INTO AN UNCHARTED AUGER HOLE MEASURING 24" IN DIAMETER. THE HOLE CONTAINED WATER WHICH CAUSED ABOUT 24" OF WATER O T ENTER THE WORKPLACE. NO CH4 OR OXYGEN DEFICIENCY WAS DETECTED. THE AUGER HOLE WAS IN THE #6 HEADING, 1 BLOCK INBY STATION #724.

AN INTENTIONAL ROOF FALL MEASURING 7' HIGH X 20 WIDE X 15' LONG WAS DISCOVERED. THE AREA WAS SUPPORTED WITH 6' AND 8' RESIN GROUTED ROOF BOLTS. THERE WAS NO INTERRUPTION TO VENTILATION OR ESCAPE ROUTES. THE FALL WAS IN #8 HEADING ONEBLOCK INBY STATION #473. THE APPROACHES TO THE FALL WERE BARRICADED AND DANGERED OFF.

THE EMPLOYEE WAS IN AN UPRIGHT POSITION TRAMMING THE ROOF BOLTER WITH THE INCH TRAM CONTROLS. A PIECE OF ROCK FELL FROM THE ROOF. IT STRUCK HIM ON THE RIGHT HAND, WHICH WAS ON THE VALVE HANDLE AND CAUSED THE HANDLE TO PUNCTURE HIS HAND.

EMPLOYEE WAS HELPING ANOTHER EMPLOYEE CHANGE SCOOP BATTERIES HE WAS ATTEMPTING TO RAISE THE BATTERIES BY PLACING A BOARD OVER THE BATERY ELEVATION JACK HIS THUMB BECAME CAUGHT BETWEEN THE BOAR D & THE BATTERY FRAME

THE EMPLOYEE WAS IN AN UPRIGHT STANDING POSITION BEHIND THE BRATTICE LINE CURTAIN. HE WAS DRAGGING CONTINUOUS MINER CABLE AS THE OPERATOR TRAMMED THE CONTINUOUS MINER OUT OF THE CROSS CUT TO START THE CLEAN UP RUN. AS THE CONTINUOUS MINER TURNED, IT CAUGHT THE EMPLOYEE BETWEEN THE BOOM AND THE RIB.

THE EE WAS IN AN UPRIGHT POSITION BUILDING A BLOCK STOPPING AS HE TIGHTENED A BLOCK AGAINST THE ROOF, SMALL PIECE OF ROCK FELL FROM THE TOP AND STRUCK HIM ON THE RIGHT SHOULDER.

THE EMPLOYEE WAS REMOVING A BROKEN BIT BY POUNDING ON A PICK HAMMER WITH A BRASS HAMMER. WHEN HE STRUCK THE HAMMER, A PIECE OF THE BIT FLEW OFF AND STRUCK HIM ON THE INDEX FINGER OF HIS LEFT H AND PUNCTURING IT.

23943K METAL HAMMER WITH OTHER HAMMER , PC OF METAL FLEW OFF OF ONE OF HAMMERS STRUCK THE EMP IN R KNEE

38505MPLOYEE WAS LIFTING MINER CABLE INTO POSITION TO BE HUNG OFF OF ROOF BOLTS, WHEN WIRES BROKE LETTING THE WEIGHT OF THE MINER CABLE COME DOWN ON HIM. THIS CAUSED PULLED MUSCLES IN HIS LEFT 09920CAGE.

THE EMPLOYEE WAS LIFTING THE LID THAT COVERS THE BATTERY ON SCOOP WITH HIS LEFT HAND. THE LID SLIPPED FROM HIS HAND AND CAUGHT HIS RIGHT INDEX FINGER BETWEEN THE LID AND THE BATTERY FRAME.

EMPLOYEE WAS WALKING AROUND THE DRILLING HEAD OF A ROOF BOLTER WHEN HE STEPPED ON A WET ROCK CAUSING HIM TO FALL AGAINST THE ROOF BOLTER,HIS MOMENTUM CAUSED A PAIR OF CHANNEL LOCKS THAT WERE I N HIS BELT TO STRIKE AGAINST HIS LEFT RIB CAGE.

EMPLOYEE WAS IN AN UPRIGHT POSITION PLACING BELT STRUCTURE ON ELEVATED BELT HANGERS. AS HE LIFTED APIECE OF STRUCUTRE OVER HIS HEAD, HE FELT A PAIN IN HIS LEFT CHEST.

EMPL WAS IN UPRIGHT POSITION ROOF BOLTING WHEN PIECE OF ROCK FELL FROM ROOF AND STRUCK EMPL ON LEFT SIDE OF EAR.