NORTH QUARRY Metal/Non-Metal

While switching plant over employee needed to use a come along to flip a gate, once the come along was grabbed the chain was knotted up. The employee hung the come along up to straighten the chain and get some slack in it, when EE pulled the slack the hook came free and struck employee in the mouth breaking one front tooth in half.

Employee was using a pry bar to remove plate from feedbox when the plate came loose and fell on EE's right ring finger resulting in a laceration/fracture.

Employee was lifting engine with shop hover head hoist to install in Euclid R-40 water truck. While using a Caterpillar lifting Bar the adjustment screw failed pinching employee right ring finger between roller resulting in laceration/amputation to the tip of finger.

CHANGING MIXING PADDLES ON PUGMILL. WAS TURNING SHAFT TO BRING UP THE NEXT PADDLE. THE OTHER PADDLE ROTATED DOWN MASHING R. LITTLE FINGER AGAINST BOOT ON R. ANKLE. DREW BACK THE HAND AND FINGE R WAS CUT.

WAS CLEANING MATERIAL AWAY FROM HOLE IN CHUTE ON TOWER #2. OTHER EE'S WERE WORKING ON A LEVEL ABOVE CHUTE CUTTING A PIECE OF METAL FROM A PLATE.THE PIECE OF METAL AFTER BEING CUT FELL THRU AN OPENING ON THE DECK AND TRAVELED TO LOWER LEVEL WHERE INJURED WAS WORKING. METAL STRUCK INJURED IN THE BACK OF HIS LEFT LEG AT THE KNEE AREA.

USING A RAM (500 LBS.) THAT WAS SUSPENDED FROM A CRANE TO LOOSEN THE HEAD NUT ON A SHORTHEAD CRUSHER. WHEN THE RAM CONTACTED THE WRENCH THAT WAS WELDED ON TO TO NUT, THEWRENCH CAME UNCOUPLED A LLOWING THE RAM TO FALL TO THE GROUND AND CONTACTING THE SAFETY SHOE OF THE INJURED EE CAUSING PARTIAL AMPUTATION OF THE LEFT BIG TOE.

EMPLOYEE WAS SAWING SPACER WHEN IT CAME LOOSE, EMPLOYEE REACHED FOR IT WHILE SAW BLADE WAS RUNNING, CUTTING HIS THUMB.

EE WAS OPERATING CRANE TO REPLACE THE WATER PUMPIN THE PIT. THE GROUND WAS NOT LEVEL ENOUGHT TO SET THE CRANE UP PROPERLY AS HE CARRIED WOODEN BLOCKS TO LEVEL THE RIGHT REAR OUTRIGGER HE STEPPED ON A LOOSE ROCK CAUSING HIS LEFT ANKLE TO TWIST

EE WAS WORKING ON EMERGENCY STEERING ON R-50 EUCLID. THE WARNING LIGHT IN THE CAB WAS NOT WORKING PROPERLY. HE CLIMBED DOWN THE BACK OF THE CAB TO CHECK THE WIREING. HE THEN PROCEDED TO CLIMB BACK INTO THE CAB. HE TOOK HOLD OF THE BROKE FLUID CAMISTER TO PULL HIMSELF UP. THE LID CAME LOOSE AND HE FELL BETWEEN THE FUEL TANKS AND TIRE HITTING THE MUD LAP BRACKET.

EE CAME DOWN COLUMN ONTO A 16'-0" HIGH CONCRETE WALL, TRIPPED. WHILE OFF BALANCE HE LEAPED TRYING TO LAND ON HIS FEET. HE THEN FELL BACKWARD LANDING ON HIS RIGHT HAND CAUSING A BROKEN RADIUS U LNA HE ALSO BRUISED THE NERVE.

USING HYUDRAULIC JACK TO COMPRESS SPRING PACK ON 7' CRUSHER. THE JACK FLEW OUT AND STRUCK EE ON THE ARM KNOCKING HIM OFF TICULER TO FLOOR.

EE WAS HOLDING A REEL OF ELECTRICAL WIRE IN HIS HAND. HE SPUN THE REEL SO AS TO SEE THE SIZE OF THE WIRE. THERE ARE 4 BOLTS THAT HOLD THE REEL TOGETHER. AS THE REEL OF WIRE WAS SPINNING THE BO LTS CUT THE THUMB AND INDEX FINGER ON HIS RT HAND.

CRUSHED INDEX FINGER TIP ON RT HAND, PUSHING CAR FOR ANOTHER EE AND DOOR WAS CLOSED ON FINGER.

EMPLOYEE WAS CHANGING FLOURESCENT TUBE IN THE DIVISION OFFICE UPSTAIRS STORAGE AREA. HE HAD ATTACHED ONE END OF THE TUBE AND WAS ABOUT TO ATTACH THE OTHER END WHEN THE TUBE EXPLODED.

METAL IN EYE.

EE WAS TALKING A C-CLAMP OFF OF THE CHUTE HE WAS FABRICATING. AFTER HE PLACED THE CLAMP ON THE CUTTING TABLE, HE TURNED AROUND, LOST HIS BALANCE AND FELL, HITTING HIS HEAD ON THE EDGE OF THE T ABLE.

THREE EES WERE UNLOADING TWO FLATBED TRAILERS LOADED WITH CONVEYOR FRAMES. WHILE UNLOADING THE SECOND FLATBED, ALL CHAINS WERE REMOVED PREPARATORY TO MOVING THE FRAMES. AS THE INJURED EE WAS R EMOVING THE LAST CHAIN, THE CONVEYOR STARTED TO MOVE, AND HE WAS PINNED BETWEEN CONVEYOR FRAME AND BELT FEEDER AND HOPPER.

EMPLOYEE WAS UNLOADING A TRUCK LOAD OF STEEL IN OUR STORAGE YARD. THE BUNDLES OF STEEL WERE TOO CLOSE TOGETHER TO WRAP THE CRANE CHAINS AROUND THEM AND HAD TO BE SEPARATED. WHEN EMPLOYEE MOV ED BUNDLE WITH A PRY BAR HE FELT A SHARP PAIN IN HIS BACK. (BUNDLE OF STEELW EIGHTED 1924 LBS)>

INJURED WAS STANDING ON THE AXLE OF A 115 KAWASAKI LOADER CHANGING THE FUEL FILTERS. AFTER COMPLETING THE TASK, HE STEPPED ONTO THE BATTERY BOX AND THEN ONTO THE STEPS TO EXIT THE MACHINE. WHE N HE DID, HIS LEFT FOOT SLIPPED ON THE TOP STEP AND HE FELL APPROX 3 1/2 FT TO THE SHOP FLOOR, SCRAPING HIS RIGHT CHEEK, SPRAINING HIS RIGHT WRIST AND BRUISING HIS RIGHT HIP AND LEG. HE

SEVERED BIG TOE ON RT FOOT & FRACTURED 2ND TOE

INJURED HAD CLIMBED UP AN 8' LADDER ONTO THE TOPSHELF OF A 8' STORAGE RACK LOOKING FOR AN ENGINEPART. INJURED WAS CLIMBING OFF OF THE STORAGE RACK BACK ONTO THE LADDER WHEN STEPLADDER FELL AWA Y FROM STORAGE RACK. INJURED GRABBED TOP RACK BEAM & LEGS FELL DOWN & RIGHT LEG STRUCK MIDDLE SHELVE BEAM, BRUISING RIGHT LEG, SHIN AREA.

EMPLOYEE FELL FROM LADDER TO GROUND.

EMPLOYEE FELL 15' AND FRACTURED HIS LEFT FOOT.

EMPLOYEE HAD A PERIODIC SCREENING CHEST XRAY READ BY 3 B READERS USING THE ILO PROCEDURES THE XRAY WAS CHARACTERIZED AS BEING CONSISTENT WITH PNEUMOCONIOSIS BY TWO READERS WITH SCOREDS OF V/1 AN 1/0 DAMAGE OR IMPAIRMENT CANNOT ABE DETERMIEDBY READING CHEST FILMS ONLY THE REPORT IS BEING SUBMITTED TO SATISFY MSHA PROGRAM POLICY LTR P92M-2

EMPLOYEE HAD A PERIODIC SCREENING CHEST XRAY REAED BY 3 B RADERS USING THE ILO PROCEDURE THE XRAY WAS CHARADCTERIZED AS BEING CONSISTENT WITH PRNUMOCONIOSIS BY TWO READERS WITH SCORES OF 1/1 & 0/1 DAMAGE OR IMPAIRMENT CANNOT BE DETERMINED BY READING CHEST FILMS ONLY THIS REPORT IS BEING SUBMITTED TO SATISFY MSHA PROGRAM POLICY LTR P92-III-2

EMPLOYEE HAD A PERIODIC SCREENING CHEST XRAY READ BY 3 B READERS USING THE ILO PROCUREDES THE XRAY WAS CHARACTERIZED AS BEING CONSISTENT WITH PNEUMOCOIOSIS BY TWO READERS WITH SCORES OF 1/1 & 0/1 DAMAGE OR IMPAIRMENT CANN0T BE DETERMINED BYREADING CHEST FILMS ONLY THIS REPORT IS BEING SUBMITTEDD TO SATISFY MSHA PROGRAM POLICYH LETTER P92-III-2

PULLING FILE FOLDER FROM LARGE FILE FOLDER. AS I PULLED FOLDER UP, END OF FOLDER JAMED AND POPPED INTO EYE.

INSTALLIG BELT ON #2 CONV. ONE END OF CABLE CONNECTED TO BELT, RAN THRU SNATCH BLOCK ON CRANE THEN CONNECTED TO LOADER. INJURED SIGNALED LDR OPER. TO BACK UP TO TIGHTEN UP CABLE TO PULL BELT U P CONV. WHEN CABLE TIGHTENED UP, IT SNAPPED, CAUSING CRANE BOOM TO BOB UP & DOWN WHICH CAUSED SNATCH BLOCK TO TAP INJURED ON BACK OF HARD HAT. HE FELL 4-5', & CAUGHT HIMSELF ON CONV. SUPPPORT

EE WAS DELIVERING A PC TO CENTROL SERVICES FOR INSTALLATION. AS SHE ROLLED THE CART INTO THE ENTRANCE, A WHEEL CAME OFF THE CART CAUSING IT TO TILT TO ONE SIDE. THE PC EQUIPMENT BEGAN TO SLIDE OFF THE CART AND SHE CAUGHT IT BEFORE IT SLID COMPLETELY OFF SPRAINING HER WRIST.

INJURED WAS POSITIONING THREE AIR COMPRESSOR ROTORS ON WORK BENCH TO BE CLEANED. THE EDGE OF ROTORS ARE EXTREMELY SHARP. HE MOVED THE FIRST ROTOR THEN THE SECOND ROTOR ROLLED OVER AGAINST THE BACK OF HIS RIGHT HAND. THE SHARP EDGE OF ROTOR LACERATED THE BACK OF HIS HAND.

EMPLOYEE HAD AIR ARC CRACK OUT IN MAIN FRAME OF REAR DUMP. EMLOYEE REWELDED CRACKS AFTER HE FINISHED WELDING, HE WAS GRINDING WELD BACK SMOOTH WHEN HE FELT SOMETHING HIT HIM IN HIS RIGHT EYE. EMPLOYEE HAD HIS SAFETY GLASSES ON WITH SIDE SHIELD AND WELDING HELMENT WITH FLIP UP FRONT ON.

INJURED WAS USING A BOAT AND OARS TO INSTALL PUMP AND FLOAT FOR DEWATERING PIT WHILE ROWING HIS LEFT WRIST POPPED.

HE WAS LOADING DISASSEMBLED TUNNEL SECTIONS ONTO 40' TRAILER. SECTION STACKS WERE BEING LOADED WITH CRANE WITH 4-WAY CHAIN WRAPPED AROUND EACH END. EVIDENTIALLY THE TOP 5 SECTIONS ON STACK WER E PULLED SEVERAL INCHES FROM LOWER SECTION BY THE PULL OF THE CHAIN. WHEN LOAD WAS LOWERED INJURED PUT HAND BETWEEN SEPARATED SECTIONS & WHEN THE TOUCHED DOWN HIS FINGERS WERE CAUGHT.

USING A DIE GRINDER WITH A WIRE BRUSH TO CLEAN 0O-RING GROOVES IN PUMP PARTS AND ONE OF THE WIRES CAME LOOSE PENETRATING THE SKIN OF THE RIGHT LEG.

EMPLOYEE WAS CLIMBING UP ON THE OUTRIGGER OF CRANE TO ACCESS THE CAB WHEN HE LOST HIS BALANCE AND FELL TO THE GROUND.

EE WAS USING RATCHET WITH UNIVERSAL SOCKET TO TIGHTEN BOLT IN A TIGHT PLACE. SOCKET DID NOT SEAT FULLY OVER BOLTHEAD. THIS RESULTED IN SOCKET SLIPPING OFF BOLT. EE S RIGHT HAND HIT EDGE OF MET AL PLATE ON ENGINE CAUSING LACERATION ON RIGHT HAND FOREFINGER.

EMPLOYEE WAS STEPPING DOWN FROM FRAME OF WATER PUMP TO THE FLOOR OF FLATBED TRAILER AND STEPPED ON PIECE OF NIPAK PIPE. TWISTING LEFT FOOT. WORKED REST OF THE DAY AND NEXT DAY. EMPLOYEE DID NOT THINK HE WAS SERIOUSLY INJURED. ON SAT 1-16, THE FOOT WAS SWOLLEN SO EMPLOYEE WENT TO THE DOCTOR. INJURYW AS A SPRAINED LEFT FOOT.

WAS PRYING INNER RACE OF BEARING FROM GEAR WHEN RACE SUDDENLY CAME OFF AND PRY BAR CUT RIGHT HAND BETWEEN THUMB AND FOREFINGER.

INJURED WAS LOADING MISC ITEMS SUCH A S CONVEYOR HEAD PULLEY SPEED REDUCEAS, 4' SH BOWL COVER, FLOATING FEEDCONE, OLD DROP BALLS AND LOADER BUCKET ONTO HIGHT FLATBED TRAILER AT ROYAL STONE QUA RRY-RICHMOND, VA TO COME TO CNETRAL SHOP WINSTON SALEM, INC.

OTHER AND EE WERE REMOVING BUCKET FROM 966 CAT LOADER. THEY WERE KNOCKING PIN FROM BUCKET. HE WAS HOLDING ROD TO DRIVE PINE OUT OTHER HIT ROD WITH HAMMER. IT GLANCED OFF AND HIT HIM IN THE FAC E, CAUSING A LACERATION TO THE UPPER JAW AND LOOSENED TEETH. TWO OF THE TEETH HAD TO BE REMOVED.

ROCK UNDER BOARD ON CONV CLIMBE D ON BELT, JABBING AT ROCK ANOTHER ROCK FELL IT STRUCK HIM O N R FOOT SPRAIN AND BRUISING IT

EMPLOYEE RECEIVED RUST IN RIGHT EYE WHILE HE WAS HAMMERING AWAY RUST FROM A CONVEYOR FRAME. A MEDICAL DOCTOR REMOVED IT WITH NO DAMAGE TO HIS EYE.

INJURED WAS STANDING ON A SCAFFOLD HE HAD MADE BY WELDING PIECE OF ANGLE TO THE INSIDE WALLS OF THE BIN AND THEN LAYED BOARDS ACROSS THE BIN ON THE ANGLE. HE WAS STANDING ON THE BOARDS, ALI GNING METAL TO WELD ONTO THE SCALPING SCREEN WHEN A BOARD SLIPPED AND HE FELL AGAINST A PIECE OF THE ANGLE. BRUISING HIS RIGHRT RIB CAGE AND SHOULDER.

INJ LOADING DIESEL ENGINE INTO BED OF SERVICE TRUCK USING CRANE BOOM MOUNTED ON TRUCK.INJ LOWERING LH OUTRIGGER MOUNTED AT REAR OF TRUCK.PULLING OUT LOCK PIN WITH LEFT HAND AND HOLDING UPPER M ID PART OF OUTRIGGER WITH RIGHT HAND AND INDEX FINGER IN HOLE.PIN CAME LOOSE AND OUTRIGGER DROPPED CATCHING FINGER.

EMPLOYEE WAS INSTALLING NEW BRAKES ON TRUCK & GOT A STEEL PARTICLE IN RT EYE

SWITCH WOULD NOT CLOSE PROPERLY. ELECTRICIAN HAD DOOR OPEN TRYING TO OBSERVE WHAT WAS CAUSING HTE PROBLEM. WHEN HE CLOSED BLADES THE WIRES SHORTED AND CAUSED FLASH.

SANDLBASTING CATWALK AND CAB PANELS OFF UH501 SHOVEL. EE WAS BACKING UP TO STRAIGHTEN SANDBLASTING HOSE AND TRIPPED OVER RAILROAD IRONS THAT HAD BEEN USED PREVIOUS TO SET PARTS ONTO SANDBLAST.

INJURED WAS CARRYING A BOX UPSTAIRS VIS THE HAND TRUCK WHEN HE FELT SOMETHING PULL IN HIS LOWER BACK.

MECHANIC WAS REMOVING OIL COOLER FROM E120 ISUZU ENGINE.TWO PHILLIPS SCREWS WOULD NOT COME LOOSE WITH IMPACT SCREWDRIVER.MECHANIC ATTEMPTED TO STRIKE SCREW WITH HAMMER AND PUNCH,AND A FRAGMENT OF PUNCH CAME OFF AND IMBEDDED IN LEFT FOREARM.

INJURED WAS HAMMERING ON PUNCH REMOVING BEARING RACE FROM DIFFERENTAIL HOUSING WHEN FOREIGN METAL FROM PUNCH CAME OFF ENTERING LEFT WRIST.

EMPLOYEE FELL FROM CONVEYOR FRAME AND FRACTURED HIS HEEL (RIGHT).

EMPLOYEE WAS HELPING MOVE A FIRE-PROOF FILE CABINET FROM ONE LOCATION TO ANOTHER LOCATION IN COMPUTER ROOM. THE CABINET MOVED OFF THE FLOOR AND CAME BACK DOWN ON RIGHT FOOT.

SAFE CONDITIONS-EMPLOYEE USED BAD JUDGMENT.

INJURED WAS ON TOP OF #3 SCREEN TO REPLACE A RUBBER PAD USED TO CUSHION THE SCREEN WHEN THE ROCK COMES OFF THE CONV. BELT. INJURED WAS USING A POCKET KNIFE TO CUT HOLEN THRU THE RUBBER SO BOLT S COULD BE PLACED THRU IT. WHILE CUTTING A HOLE, THE POCKET KNIFE BLADE CLOSED UP ON HIS RIGHT INDEX FINGER, CUTTING IT.

WORKING CONDITIONS WERE GOOD AND DID NOT CONTRIBUTE TO INJURY.

EMPLOYEE WAS ARCING WEAR PLATES FROM BOTTOM OF 501 BUCKET WITH SECOND EMPLOYEE.BOTH EMPLOYEES WERE WORKING SIDE BY SIDE IN BOTTOM OF BUCKET.FIRST EMPLOYEE RECEIVED FLASHES OFF THE SECOND EMPLO YEE ARC AIR.

INJURED WAS DRIVING PIN BACK INTO ELECTRODE HOLDER. STEEL PARTICLES FLEW OFF HITTING WRIST & CUTTING BLOOD VESSEL.

EMP HAD BUILT UP WORN AREA WITH WELD AND WAS GRINDING AREA BACK DOWN WHEN PIECE OF METAL GOT INTO HIS EYE. HE WAS NOT AWARE OF THIS INITIALLY. IT LATER BOTHERED HIM AT NIGHT. HE WAS USING SAFE GLASSES AND WELDING HELMET

INJURED HAD FINISHED STEAMING MACHINE AND WAS IN THE PROCESS OF CUTTING STEAM JENNY OFF AS HE DISCONNECTED THE STEAM LINE SOME STEAM BLEW OUT AND BURNED HIM.

EMPL BENT DOWN TO PICK UP 3"X5"?X6' ANGLE IRON FELT SHARP PAIN IN STOMACH & GROIN.

EMPLOYEE WAS LYING ON LEFT SIDE ON FLOOR WELDING UP UNDER STARTER. WELDING SPARK WENT INTO RT EAR.

EMPL REACHED DO4N WITH BOTH HANDS TO SLIDE STEEL BAR ON TO PIECE OF ANGLE TO ALLOW LIFTING CHAINS TO BE HOOKED.AS HE PULLED ON STEEL FELT PAIN IN LOWER BACK.3/8'' X 9'' X 20'.

FLUME SLIPPED O6T OF SUSPENDED WATER COLLECTION BOX WHEN LIFTING CHAIN TWISTED, FALLING ON INJURED WHO WAS MOVING TO THE OTHER SIDE OF FLUME. INJURIES INCLUDE BRUISED LEFT AND RIGHT ARMS AND S ALSO LACERATION8 TO THE LEFT ARM

INJURED WAS USI3G A STRAIGHT EDGE TO PULL KNIFE ALONG HOLDING STRAIGHT EDGE WITH TGHE LEFT HAND & PULLING THE KNIFE WITH THE R T THE KNIFE SLIPPED OUT OF THE RUBBER CUTTING THE LEFT RING FING ER 3

AIR COMPRESSOR 4AS RUNNING HOT WATER LEVEL WAS LOW.INJURIED THEN CLIMBED UP ON THE SIDE OF THE COMPRESSOR TO THE RAIL WITNESS THEN HANDED THE WATER HOSE TO THE INJURIED THEN HE PRECEEDED TO FI LL THE RADIATOR1THE INJURIED TRIED TO REMOVE WATER HOSE ,DURING THAT TIME GOT CAUGHT ON THE HANDLE THAT'S ON THE SIDE DOOR OF THE COMPRESSOR.THE INJURIED THEN PRECEDED TO MOVE CLOSER TO WHERE

CONVEYOR HAD BE9N STOPPED TO REPAIR EQUIMENT AT AN ADJACENT CONVEYOR SUBJECT WAS SITTING ON CONVEYOR NEAR TAIL END HOLDING A SURVEYOR ROD. PLANT MAINTENACE PERSONNEL REPAIRED TROUBLE AND RESTA RTED CONVEYOR. 8UBJECT STRUCK TRANSFER CHUTE, TRIED TO GRAB CHUTE, LEGS WERE HIT, AGAINST CHUTE INJURING LEFT KNEE, LOST HIS BALANCE AND FEEL OFF CONVEYOR 12 FT.

EMPLOYEE WASIN 5 SMALL OPENING INSTALLING PLATES ON THE HOPPER ON THE SURGE BIN. HE HAD WELDED ON THE FIRST PLATE AND WAS GRINDING OFF THE SLAG WHEN THE GRINDER KICKED BACK AND STRUCK THE EMPL OYEE ON THE LEF7 KNEE INFLICTING THE LACERATION THAT REQUIRED 6 STITCHES.

EMPLOYEE SLIPPE8 ON CERAMIC TILE FLOOR IN RESTROOM OF DIVISION OFFICE AND FALLING ON HER BACK

DURING THE TIME3OF THIS ACIDENT THE WELDER ASKED THE INJURIED PERSON TO ASSIST HIM IN TURNING OVER THE OXYGEN TANK RACK ON THE OPPOSITE SIDE AS RACK WAS BEING LOWERED TO THE FLOOR THE INJ P PERSON MOVED HI8 RT LEG IN DOING SO HIT A PIECE OF ANGLE IRON THAT WAS PART OF THE RACK AT THAT TIME LACERATING HIS LEG

EMPL STANDING O3 FRAME OF HYDRAULIC SHOVEL BESIDE ENGINE.AS HE ATTEMPTED TO POSITION TACHOMETER IN TACH DRIVE WITH RIGHT HAND GLOVED HAND CAME IN CONTACT WITH OR WAS SUCKED INTO FAN THAT WAS R UNNING AT FULL 9PM-2200 RPM.

INJURED WAS STANDING BESIDE DRILL AT OPERATING LEVERS, OPERATING DRILL, WHEN THE SPARE DRILL STEEL FELL FROM THEIR STORAGE RACK. THE FIRST PIECE STRUCK INJURED\S HARD HAT, KNOCKING IT OFF HIS HEAD. THE SECOND PIECE, WHICH FELL IMMEDIATELY AFTER THE FIRST, STRUCK INJURED DIRECTLY ON THE HEAD, NEAR CROWN AREA LEAVING A CUT APPROX. 3" LONG.

BEARINGS ON SECO SCREEN HAD BEEN REPLACED FLYWHEEL HAD BEEN HOISTED AND SLID APPROX 1/2" ONTO SHAFT INJURED WAS ROTATING FLYWHEEL TO ALIGN KEYWATS. FLYWHEEL SLIPPED OFF SHAFT AND MASHED FINGER

LARGE ROCK WAS HUNG IN JAW CRUSHER & INJURED WAS ATTEMPTING TO FREE IT INJURED LOWERED CABLE FROM OVERHEAD HOIST INTO JAW CATCHING HOOK UNDER ROCK WHILE RAISING CABLE ROCK LODGED AGAINST JAW DIE CAUSING CABLE & HOOK TO FLY OUT & OVER GUARD RAIL STRIKING OPERATOR BREAKING RT FOOT

EMP HAD ENTERED EMPLOYEE BLDG TO LEAVE FUEL REPORT AS HE LEFT BLDG HE STUMBLED AND FELL DOWN STEPS FRACTURING LEFT FOOT