Oregon Plant Metal/Non-Metal

While shutting down to change a roller the torch for BC-61 was not shut down properly causing the belt to catch on fire and the fire department was called and had the fire was out at 4:50AM.

Employee was using a grinder and slipped and lost balance while grinding. Employee received an injury to right index finger which required 3 stitches.

Employee was driving a club car in the quarry when they reached for their radio releasing the steering wheel, which caused the wheel to spin hard to the left. When the employee attempted to correct the steering wheel, they also pressed the brakes. This caused the mobile equipment to ascend the berm and tip over on the passenger side.

The Dryer operator was using a mini skid to perform general cleanup of the Dryer Building. While traveling in reverse, they pinched their little finger between the mini skid and an I-beam cross member.

The miner lost footing while entering DR-02. When they went to catch themselves their left elbow came in contact with a sharp edge inside of the dryer drum. This caused a laceration and they received 5 stiches.

On 6/22/22 at 9:00am a maintenance employee was tightening a bolt on the jaw crusher and the wind blew something into EE's eye. EE tried washing it out but was unsuccessful. The miner went to the local doctor office and they were able to remove a foreign object from EE's eye.

The miner injured EE's knee while stepping across the wet screen to perform maintenance. The miner slipped when stepping from the top of the eccentric housing to a round support member.

Employee was using a bar to try to unplug HO-18. It became plugged due to extreme cold weather and frozen chunks of sand. While trying to free the hopper of frozen sand employee strained left shoulder.

At approx. 3:15am the belt tender lit a torch on BC-09 then started walking to truck. While EE was walking to truck, EE lost footing and twisted ankle. EE called supervisor and reported the incident. EE stated that the soft spot on the bottom of the foot was hurting. The miner has a fractured bone in foot.

On 11/4/21 at 6:45am employee was leaving the trailer to drop off paperwork in the main office. While going down the stairs they missed the last step and fell to the ground. EE stated it was their first week in the new office and was use to having 3 steps not the 4 we have now. EE missed the last step thinking they were on the ground level.

Employee was tasked with cleaning frozen material from quarry hoppers. While using an ice scraper to free the material employee felt pain in shoulder and neck.

Employee was attempting to clean out the sump hole at the west end of the reclaim building. When EE tried to lift the sump pump from the hole EE felt a pop in EE's right forearm. Employee reported the incident to EE's supervisor and finished EE's shift. The following Monday (9/14/20) the employee visited a doctor who placed EE on modified duty and suggested an MRI.

The employee works in a position where frequent shoveling is required. EE's shoulder has been sore for a while and aggravated by shoveling. Is experiencing tingling in EE's arm when trying to sleep. Went to Dr. who says scar tissue has built up and prescribed 6 weeks of physical therapy.

FLW was removing an idler pulley from a piece of tracked equipment. While striking the pulley with a 3# hammer a shard of metal came off of the hammer and struck the worker in upper thigh.

Employee was replacing a troughing roller on BC54 at the head end of the belt. While turning to pick up a bolt to fasten down the new assembly EE hit knee on the torque arm support for the reducer. This caused EE's knee to flex sideways. EE was experiencing some swelling and soreness. Update: Went to doctor on 9-20-19 and scheduled an MRI for 9-25-19.

Employee was thawing out bridged material above BC-107 and a large piece broke off. Employee pulled the torch back that EE was running and in doing so twisted shoulder. Required no medical attention at the time. 8 months after the incident EE was having issues with the shoulder and went to the doctor for an examination.

Miner put ladder into a hopper to unplug frozen sand. Miner had fall protection on. Before standing on frozen sand the area was 'tested' with sledge hammer. The area gave way & miner fell 3 ft. Miner's rt knee hit the hopper causing bruising. The miner grabbed ladder to help arrest fall causing a strained rt shoulder. Miner completed shift & was examined the next day.

Miner was walking to the parking lot at the end of EE's shift. EE removed EE's half face respirator while enroute and took EE's eyes off the ground EE was walking on. As a consequence, EE tripped on the pavement, and fell landing on EE's right shoulder.

Miner was on a step ladder, approximately 5' High. Miner had 3 points of contact while attaching a hose. Miner twisted while installing the hose shifting EE's body weight causing the ladder to kick out from under EE. The miner fell striking EE's rib area. Miner was assessed and had no signs of injury but was taken to emergency room to be checked out.

The employee was carrying a Screen eccentric on shoulder, while taking it off shoulder to load in the back of a pickup truck ee smashed middle finger on right hand between the tailgate and eccentric.

The employee was covering the end loader during the operators lunch and jarred their back. Employee went to the Chiropractor and was given light duty.

Employee was attempting to clean out auger when EE's left index finger came in contact with the auger blade lacerating tip. First aid and medical treatment was provided. The index finger was partially amputated. Employee returned to work on 4/29/16 with restrictions.

The employee felt a pain in his shoulder while exiting a man hole. This was not re-portable until 10/11/16 when the employee had to have surgery.

Original incident happened on 11/13/2014, has now become an MSHA reportable as of 07/09/2015. Employee was working in a warehouse storage building used for spare parts. He went to open a large spring loaded overhead door, he reached up to pull the chain to open the door, the door did not move and employee felt a pop in his left shoulder.

Employee was helping to remove head pulley lagging on a conveyor, as he was turning the pulley by use of drive belts, his finger became caught in the motor sheave, since conveyor had a back/stop sheave would not reverse, so two drive belts were cut off to free employees index finger from between drive belts and sheave of motor. Tip of employees index finger was broken.

EMPLOYEE WAS WORKING IN MOBILE MAINTENANCE SHOP AS AN ASSISTANT. A MAINTENANCE TRUCK WAS ON THE HOIST AND EMPLOYEE WAS SERVICING FRONT DIFFERENTIAL WITH/80/90 GREASE. FILLING WAS COMPLETE AND HE DUCKED TO GET PAST REAR DIFFERENTIAL AND THEN WALKED INTO THE SHOCK ABSORBER MOUNT, WHICH IS LOCATED UNDER THE REAR AXLE. CUTTING THE TOP OF HIS HEAD.

Injured employee was performing his normal belt tending job. Some of the conveyor belts stopped running and employee had to turn the LP gas off which was heating the conveyor belts. He got out of the truck and started towards the shutoff valve and then slipped on the sand, snow, and ice with his right foot. His left shoulder struck the vertical beam under the BC03 stairway.

Employee electrician was splitting telephone wire with a utility knife, he was splitting wire by pulling the utility knife towards him, in doing so the knife slipped and cut employee in the abdomen requiring (4) stitches.

ORIGINAL INJURY WAS REPORTED TO MSHA ON 10/3/2011 ON FORM 7000-1. RETURN TO FULL DUTY REPORT WAS SENT IN ON 09/04/2012. EMPLOYEE REPORTED HE HAS INJURED HIS SHOULDER AGAIN AND HAS BEEN PUT ON RESTRICTED DUTY AS OF 01/18/2013. THIS FORM IS BEING RESUBMITTED AS A NEW INCIDENT.

EMPLOYEES WERE ATTEMPTING TO CLEAN OUT A SAND SAMPLER 2" PIPE OF WET SAND, ONE EMPLOYEE WAS UP ONE LEVEL AND OTHER EMPLOYEE WAS AT BOTTOM OF THE PIPE TO BE CLEANED OUT. AS UPPER EMPLOYEE WAS RODDING OUT WET MATERIAL BAR SLIPPED FROM HIS HANDS AND IN DOING SO LOWER PERSON WAS HIT WITH BAR ON HIS LEFT INDEX FINGER.

Employee was carrying 24"x24" sheets of roof siding. While carrying pieces of this sheeting a piece fell onto the catwalk he was walking on. Employee did not notice he had dropped a piece and stepped on the piece lying on the catwalk causing him to slip and fall hitting his knee on the expanded metal catwalk.

Employee was picking up (2) 50lb. bags of sand from a pallet, as employee was lifting bags he felt a popping in his stomach area. He continued to carry bags to bagging building loading door to be loaded out into a vehicle.

EMPLOYEE WAS HELPING TO RE-RAIL A RAIL ROAD CAR. RE-RAILING EQUIPMENT WAS BEING PUT INTO PLACE AND RAIL ROAD SPIKES WERE DRIVEN INTO RAILROAD TIES. AS EMPLOYEE WAS DRIVING A SPIKE THE SPIKE CAME OUT OF TIE AND STRUCK EMPLOYEE IN LEFT INDEX FINGER

Maint. needed to be performed in quarry, so production supervisor fueled welder which was mounted in back of pick-up truck. When finished he stepped down from back of pick-up with his right leg. Once his right foot was one foot from ground he stepped down and felt pain in his right knee.

EE was attempting to move a Drisco Pipe 6" Dia X 22'8" in Length with steel flanges on both ends. Steel flange on pipe caught on floor, from a steel block measuring 6"x6" square and sticking up 1/4" that had been welded over a bin hole in screen house. EE jerked on pipe to free up, pipe came loose and rolled into a steel support beam, striking L hand between beam and pipe.

Employee was bagging 100lb bags from a bag conveyor to pallets, while stacking bags he felt a pain in his right shoulder area.

EE was working on uneven quarry floor. He is not sure what caused injury in his words, more of a cummlative injury by being jostled in the endloader cab.

Employee was exiting F-250 pickup truck-while stepping down he slipped on ice striking his back and ribs on running board. This was reported but did not become reportable until 1/20/10

Due to the heart attack, the operator was not in controll of the truck and ran into the cut wall causing minor damage to the front of the truck. This occured while performing overburden work at the mine

EE had just put a ladder in back of a pick up truck as he was walking to the drivers door he slipped on the ice and fell. A light dusting of snow had fallen and covered the ice.

Employee was working from South Quarry stockpile with endloader. While backing from pile tire entered uneven area swaying endloader. At this time employee felt pain in his right side lower back.

Injury was working on dryer line 3 with other empoyee. After lunch. He went back up the stairs and started across the elevated walkway. As he crossed the walkway, the grating shifted and he fell approx. 10' to the concrete floor below.

EE was performing clean up work with a shovel and wheel barrow, EE was walking behind line #3 cooler when he slipped and fell, EE slipped on the thin layer of ice. EE struck his back when falling on the old cooler.

Employee was cutting weeds on hill beside belt conveyor #11 with hand held gas weed eater. He stepped into a hole twisting and straining his right knee. (Note knee surgery May 1, 2009)

Employee had completed tying up 4" rubber hose with 1/4" nylon rope. He turned to leave area and stepped onto 4' high toe board or toe guard. He fell when his right foot became partially stuck in small hole in floor grating along side hose going thru floor grating.

Employee was welding the edges of a roll crusher, while adjusting his welding hood he exposed himself to welding flash from surrounding equipment.

Employee was walking down steps inside control booth. He was wearing ice creepers on his feet and had not taken them off when he entered the building. His foot slipped on a step twisting his right ankle.

EE was helping co-worker close door on box car. Door moved a couple of feet, became stuck. EE then pulled on the door with both hands. The door traveled a couple of inches, stuck again. When the door stopped, ee felt a pop in both his shoulders and wrist. (surgery on 10/17/06)

Employee was cleaning putty off of 20" x 14" x 1/4" steel door plate while standing on a ladder. Lid slipped off edge of platform and struck employee on top of left foot behind steel toe of shoes.

EE WAS CHANGING LINERS ON DENVER SLURRY PUMP WHEN LINER MOVED PINCHING LEFT RING FINGER, FRACTURING TIP.

OPERATORS WERE WORKING IN BAGGING DEPARTMENT; AN AIR-OPERATED ACTIVATOR AND DIVERTER WERE NOT WORKING. WHILE WORKING ON EQUIPMENT, INJURED STEPPED OFF OF FLOOR GRATING AND TRIPPED, LANDING ON HIS RIGHT SIDE.

INJURED CLAIMS TO HAVE BEEN USING AN OVERHEAD HOIST TO RAISE A CRATE OF SCREEN PANELS UP TWO FLOORS IN THE SCREEN HOUSE. WHEN THE LOAD WAS BEING LOWERED IT BECAME CAUGHT ON A HAND RAILING. WHE N THE CRATE WAS MOVED OFF THE RAILING IT DROPPED SLIGHTLY, WHICH STARTLED THE EMPLOYEE. HE STATED THAT HE MOVED BACK AND OFF TO ONE SIDE AND HE FELT SOMETHING POP IN HIS BACK.

EMPLOYEE WAS HOOKING UP RAIL CARS FOR LOADING WHILE WALKING ALONG THE TRACKS HE STATED HE STEPPED IN A HOLE OR ON A ROCK TWISTING HIS LEFT KNEE.

OPERATOR WAS DESCENDING LADDER ON ENDLOADER YEAR 2000. WHEN HE REACHED SECOND STEP FROM BOTTOM, HIS RIGHT ANKLE GAVE OUT CAUSING HIM TO LOOSE HIS BALANCE AND FALL TO THE GROUND ON HIS BACK AND RIGHT HIP.

OPERATOR WAS EXITING DOZER CAB FOR LUNCH BREAK, AS HE WAS STEPPING OUT OF CAB HIS LOOP ON SIDE OF COVERALLS CAUGHT ON DOOR HANDLE. THE JERKING MOTION CAUSED HIM TO LOSE HIS BALANCE AND SLID FROM DOZER TRACKS, HIS RIGHT KNEE STRUCK THE STEEL GROUZER ON TRACKS.

INJURED WAS REPAIRING A CRACK IN THE FRAME OF THE DUCLID HAUL TRUCK. THE CRACK WAS ON THE BOTTOM OF THE FRAME. INJURED WAS WEARING ALL WELDING PROTECTIVE EQUIPMENT. HIS HEAD WAS COCKED TO THE SIDE WHEN WELDING SPLATTER ENTERED THE EAR CANAL AND DAMAGED THE EAR DRUM. INJURED WENT TO SEE A DOCTOR ON 11-11-02, RETURNED TO WORK 11-11-02.

EE WAS PREPARING TO SERVICE A PIONEER JAW CRUSHER, HE EXITED CONTROL BOOTH WITH A 5 GAL. GREASE PUMPER WHICH IS USED FOR SERVICING. WHILE WALKING ALONG SIDE OF CONTROL BOOTH HE TRIPPED OVER A WIRE ALONG SIDE OF BUILDING.

EE WAS OPENING BOTTOM DOOR ON RAIL CAR TO CLEAN COMPARTMENT. DOING SO HE STTATED HE STRAINED HIS LOWER BACK.

EE WAS DECENDING DOWN AN EXTENSION LADDER. EE WAS HOLDING ONTO A 5 GALLON BUCKET WITH TOOLS, WHEN HIS FOOT SLIPPED ON THE RUNG OF THE LADDER.

THE BOTTOM DECK BEAMS ON VS-07 WERE BEING TORCHED OUT FOR REPLACEMENT. EE WAS TORCHING THE STEEL BEAMS ON VIBRATING SCREEN-07 WHEN A SPARK LANDED ON HIS LEFT GLOVE (RING FINGER). EE DID NOT NO TICE IT UNTIL THE SPARK HAD BURNT THE END OF THE GLOVE, CAUSING SECOND DEGREE BURN TO THE LEFT RING FINGER.

A RAILCAR WAS PULLED OVER DUMP AREA AFTER LOADING WHEN IT WAS DISCOVERED A CENTER BOTTOM DOOR WAS LEAKING, WHILE EE WAS ATTEMPTING TO OPEN DOOR,HE FELT A PAIN IN HIS UPPER RT. BACK & SHOULDER.

EE WAS HELPING RELOCATE A CABLE ON DREDGE, WHILE WALKING ALONG AREA OF GROUND HE STEPPED INTO AN INDENTATION IN GROUND AND TWISTED HIS RIGHT ANKLE.

EE WAS SHOVLING SAND FROM UNDER JAW CRUSHER, PREPARING TO MOVE. EE WAS INSIDE FRAME OF CURSHER. A JD 555 CRAWLER WAS BEING USED TO CLEAN UP LOOSE SAND FROM AROUND CRUSHER. WHILE DIGGING, CRAWL ER FORCED A ROCK UP INTO SHOVEL AND EE HAD HIS RIGHT HAND ON TOP OF SHOVEL, FORCING SHOVEL INTO FRAME, CATCHING HISRIGHT HAND BETWEEN FRAM OF CRUSHER AND TOP OF SHOVEL HANDLE.

EMPLOYEE WAS GOING TO HOOK UP AIR LINES ON RAIL CARS WHEN LOADOUT OPERATOR PUSHED TOGETHER. WHEN CONNECTING MARK, HE FELT HIS ARM BEING PINCHED BETWEEN KNUCKLE OF NEXT RAILCAR. HIS FORARM WAS CAUGHT.

EMPLOYEES WERE CHANGING PUMP LINERS IN A DENVER SLURRY PUMP. WHEN PUTTING PUMP BACK TOGETHER EE CAUGHT TIP OF RINGER ON BACK SIDE OF PUMP LINER FRACTURING/LACERATING TIP OF FINGER.

EE WAS REMOVING LADDER FROM BACK OF MAINTENANCE TRUCK. WHILE TURNING ON UNEVEN SURFACE HE FELT HIS BACK PULL. EE WENT TO DR ON 2-7-01.

EE WAS SETTING ON DOZER TRACK, ATTEMPTING TO LIFT STARTER MOTOR INTO ENGINE AREA. THE AREA WAS LOWER THAN DOZER TRACK HE HAD TO WORK FROM AND WHILE WORKING IN THE AWKWARD POSITION HE FELT SOME THING PULL IN HIS LOWER BACK.

EMPLOYEE IS NOT SURE WHAT HAPPENED; STATED HE HAS BEEN HAVING BACK AND HIP PAIN FOR SOME TIME.HAS HIP JOINT INFLAMED AND IS ON THERAPY.

EE WAS ATTEMPTING TO REMOVE A 48" X 96" PIECE OF SHEET STEEL FROM STEEL RACK WITH A HOIST. AS HE WAS REMOVING HIS FOOT SLIPPED AND HE FELL BACKWARDS, STRIKING A REDUCER BEHIND HIM.

EE WAS TRYING TO CHIP OUT A ROCK THAT WAS STUCK IN THE JAW CRUSHER. THE BAR BOUNCED OFF THE ROCK, PUSHING EE'S WRIST INTO THE HAND RAILING.

EE WAS UNLOADING SCRAP STEEL FROM BACK END OF PICKUP TRUCK. A PIECE OF ANGLE IRON SLIPPED, STRIKING BACK OF HIS LEFT HAND.

EE WAS CUTTING THE BUSHINGS OUT OF THE BOOM ARMS ON THE L-330-C ENDLOADER. SOME HOT METAL BLEW BACK AND UP EE'S LEATHER WELDING COAT, BURNING HIS RIGHT FOREARM.

EE WAS PUSHING A PIPE OUT OF THE WAY IN THE ROLL CRUSHER AREA, STEPPED IN LOOSE SAND AND TWISTED HIS LEFT KNEE AND LEG.

COWORKERS WERE WORKING ON THE JACK AT THE ROLL CRTUSHER--HYDRAULIC HOSE BROKE FREE, PRESSURE TOOK SKIN OFF OF EE'S RIGHT FOREARM.

MECHANIC HAS REMOVED RIGHT FRT TIRE FROM L320 LOADER BEGAN MOVING AXLE UNIT WHEN TIRE ROLLED CATCHING EE RIGHT HAND AGAINST SPINDLE OF FRT AXLE

EE WAS LEAVING THE ROUND HOUSE THROUGH THE NORTH DOORS. STEPPED DOWN OFF THE STEPS AND TWISTED HIS RIGHT ANKLE WHEN HIS FOOT SLIPPED OFF THE STEP.

EE AND OTHER EE WERE UNLOADING A MOTOR BASE FROM THE BACK OF THE DODGE MAINTENANCE TRUCK AT CARLOADING. EE TWISTED HIS BACK WHILE LIFTING ON THE MOTOR BASE. WENT TO CHIROPRACTOR 4-14-99 AFTER BACK BECAME WORSE.

EMPLOYEE WAS CHOPPING A QUARRY PUMP OUT OF ICE WITH A 4' PRY BAR AND A 16 POUND SLEDGE HAMMER.

EE WAS CHANGING A PORTION OF WIRING INSIDE CAB OF MUDCAT DREDGE. SCREW DRIVE SLIPPED OFF HEAD OF MACHINE SCREW MAKING A SMALL PUNCTURE WOUND ON TH4E INDEX FINGER OF EE'S LEFT HAND. EE WORKED R EGULAR SHIF ON 7-13 AND 7-14. ON 7-15 WENT TO ER

INJ WAS STACKING 50# BAGS DURING SECOND PRODUCTION RUN OF BAGS HE FELT A SENSATION IN HIS LOWER BACK. INJ STATED THAT HE FELT HE MUST HAVE TURNED WRONG. HE STATED HE WAS STACKING BAGS IN THE S AME MANNER THAT HE HAD USED BEFORE.

OPERATOR WAS CLEANING OUT SCREEN HOPPERS US-29 &US-30. PROXIMITY ALARM WENT OFF. HE TRIED TO OBSERVE OTHER OPERATOR TO SEE WHICH HOPPER WAS BACKING UP. WHILE LOOKING THROUGH FLOOR GRATING HE W ALKED INTO I-BEAM. CUT FOREHEAD REQUIRING 2 STITCHES TO CLOSE.

EE WAS OPERATING THE SMALL CLEAN-UP LOADER IN THE QUARRY. HE DROVE THE SMALL END-LOADER OVER SOME BUMPS IN THE ROAD, CAUSING THE LOADER TO BOUNCE AND AFFECT THE EMPLOYEE'S BACK.

EE WAS ATTEMPTING TO REMOVE A FILTER CLOTH, WHICH HAD BECOME CAUGHT IN A SCREW AUGER. CLOTH CAME LOOSE AND EE FELL BACKWARDS ONTO FLOOR GRATING AND CUT BACK OF HIS HEAD.

REMOVING BOTTOM SECTION OF HOPPER FROM HYDROSIZER TANK. THIS WAS BEING DONE WITH COME A LONGS. HOPPER WAS LOWERED. WEIGHT OF HOPPER SHIFTED AND HOPPER FELL WITH EMPS HAND GETTING CAUGHT IN CHA IN AGAINST HOPPER THAT WAS BEING LOWERED.

AS OPERATOR FILLED HIS BUCKET WITH SANDSTONE A PIECE OF ROCK WAS TRAPPED BEHIND THE BUCKET AND THE TILT ARMS OF THE LOADER. OPERATOR WAS NOT ABLE TO SEE THIS ROCK AS HE WAS TRAVEING TO PRIMAR Y CURSHER. WHILE ATTEMPTING TO DUMP BUCKE THE PIECE OF ROCK CAME DOWN, STRIKING WINDSHIELD ANDA PIECE CAME THROUGH WINDSHIELD STRIKING EE IN PELVIC AREA.

EMPLOYEE WAS WALKING TO HIS LOCKER IN MAINT. BUILDING. AS HE WAS APPROACHING LOCKER HE STEPPED ON PARTLY EXPOSED SPOOL OF GREASE LINE HOSE. EMPLOYEE CAUGHT HIS FOOT ON SPOOL, TRIPPING AND FALL ING TO HIS KNEES.

EE WAS MOVING BLOCKING SETTING CRUSHER UP WHEN HE FELT A PAIN IN HIS GROIN AREA.

EE WAS TRYING TO BREAK A ROCK LOOSE IN THE JAW CRUSHER WITH A WEDGE THAT HAD A CHAIN ATTACHED TO IT. WHEN THE ROCK BROKE AND FELL DOWN INTO THE JAW, A ROCK BEHIND THAT ROCK FELL ON THE WEDGE A ND CHAIN JERKING HIS RIGHT SHOULDER, PULLING HISARM OUT AND DOWN.

EE WAS REMOVING A ROCK FROM CONVEYOR HPPER, EE WAS LEANING OVER SIDE OF HOPPER WHILE LIFTING ROCK. AS HE WAS LIFTING ROCK HE FELT A PAIN IN HIS LOWER PELVIC AREA.

EE WAS REMOVING A LARGE GEAR FROM THE TRIPLE ROLL CRUSHER. HE WAS STANDING ON TOP OF A 250 H.P. MOTOR, WORKING A COME A LONG TURNED TO SET 4' BAR DOWN AND STEPPED ON A SOCKET WRENCH THAT HAD B EEN SET DOWN ON THE ELECTRIC BOX COVER OF THE MOTOR , LOST HIS FOOTING AND FELL APPROX. 2' TO CATWALK, SPRAINING HIS RIGHT WRIST AS HE LANDED ON THE CATWALK. IT WAS LATER FOUND THAT HE HAD A

EE WAS INSTALLING BOLTS ON NEW QUARRY CONVEYOR INSTALLATION THE BOLTS WERE ON TROUGHING IDLERS. SOME OF WHICH DID NOT HAVE BOLT HOLES INSTALLED AND WAS TORCHING HOLES AS NEEDED. EE TORCHED OUT ONE HOLE AT IDLER AND SET LIT TORCH DOWN ON FRAME OF CONVEYOR WHILE LIT, TORCH FELL FROM RESTING PLACE AND LANDED ON HIS LEFT HAND BURNING HAND.

EE WAS CHANGING A LIGHT BULB IN THE HYDRAULIC ROOM AT LOADING, WHEN THE BUCKET HE WAS STANDING ON SLIPPED ON THE OILY FLOOR. EE LOST HIS BALANCE AND FELL. BREAKING THE LIGHT BULB, WHICH CUT TH E PALM OF HIS RIGHT HAND.

EE WAS SETTING RAILCAR BRAKE WHEN HE FELT PAIN BETWEEN HIS SHOULDER BLADES.

EE WAS PRYING ON A CONVEYOR REDUCER WITH A 4IN PRY BAR THINKS HE MAY HAVE STRAINED HIS BACK MUSCLE SPASMS STARTED AROUND 4PM AT HOME

EE WAS SHOVELING SAND FROM THE FLAT ROOF OF THE WASH HOUSE AND DUMPING OVER THE EDGE OF THE BUILDING HE SAYS THAT THE WIND CAUGHT THE WHEELBARROW. CAUSING HIM TO LOSE HIS BALANCE AND FALL 5FT 7 INCH FROM THE ROOF OF THE BLDG ONTO THE SAND PILE BELOW.

INJURED WAS STANDING IN THE LOOSE SAND THAT HE WAS SHOVELING FROM THE TRACKS. AS HE TURNED WITH ASHOVEL FULL OF SAND, HIS LEFT FOOT SLIPPED OFF HTE TRACK RAIL AND HE FELL, STRIKING HIS LEFT KN EE ON THE RAIL TRACK JOINT.

INJURED WAS ATTEMPTING OT MOVE A PUMP VOLUTE SHELL WITH A CHAIN HOIST SO HE COULD RAISE IS UP ONTO A CART. WHENTHE CHAIKN TIGHTENED ON THE SHEELL,THE HOOK CAME LOOSE AND HT ESHELL FELL ON HIS LEFT FOOT ABOVE THE SAFETY SHOE TOE GUARD.

INJURED WAS CLEANING WET SAND FROM TEH #7 SILO DISCHARGE WITH HIS HAND. UNAWARE THAT HE WAS CLEANIGN WET SAND FROM TEH SILO DISCHARGE, THE OTHER SCREEN OPERATOR ACTIVATED THE ELECTRIC BIN GAT E CLOSURE FORM THE SCREEN HOUSE, CATCHING HIS FINGER BETWEEN THE BIN CLOSURE GATE AND THE SILO DISCHARGE PIPE.

EMPLOYEE CRAWLED FROM BENEATH VS41 SCREEN AFTER REINSTALLING DRIVE BELT THAT HAD COME OFF. HE RAIRED UP TOO QUICKLY & STRUCK HIS COLLARBONE ON THE SCREEN STRUCTURAL FRAME.

EE WAS IN THE TOP SCREEN FLOOR SHACK WHEN THE ALARM FOR VS63 WENT OFF. AS EE WENT THROUGH THE DOOR, THE RUBBER STRAP USED FOR HOLDING THE DOOR SHUT, BROKE AWAY FROM THE "S" HOOK HOLDING IT TO THE JAM, HITTING HIM ON THE RIGHT ELBOW. EE LATER NOTICED A LARGE KNOT FORMING ON HIS RIGHT ELBOW.

EMPLOYEE WAS USING A BAND SAW TO CUT A REDI SLEEVE SKIRT. HE DID NOT SECURE THE SLEEVE BUT HELD IT IN HIS HAND. STEEL ROTATED IN HIS LEFT HAND, CUTTING THE SECOND FINGER.

EMPLOYEE WAS ATTEMPTING TO DRILL OUT SET SCREW IN BAGGING SPOUT, EMPLOYEE WAS HOLDING SPOUT WHILE ATTEMPTING TO DRILL, BIT BROKE IN DRILL DEFLECTING BIT ACROSS THE TOP OF RIGHT INDEX FINGER CUTTING BETWEEN KNUCKLE AND FIRST JOINT.

EMPLOYEE WAS MOVING 2" CLEAN UP HOSE BETWEEN PUMP #1 AND PUMP #3. EMPLOYEE HAD 6" STEEL ELBOW IN ONE HAND TO USE FOR WIGHT TO HOLD HOSE IN PLACE WHEN NOT BEING HAND HELD. PHONE RANG EMPLOYEE S TARTED TO PUT HOSE DOWN TO ANSER PHONE HE DID NOT REALIZE HOSE HAD BECOME TANGLED AROUND LEGS. THIS CAUSED HIM TO LOOSE HIS BALANCE. WHILE TRYING TO REGAIN HIS BALANCE EE FELT HIS BACK POP. I

54736YEE WAS WALKING UP TO THE CARLOADING AREA VIA THE BASEMENT STAIRWAY, WHEN HIS LEFT FOOT SLIPPED OFF OF THE STEP, TURNING HIS ANKLE SIDEWAYS.

INJURED WAS IN THE PREOCESS OF TROUBLESHOOTING A PLUGGED SUMP DISCHARGE PIPELINE, WALKING IN A WATER SATURATED AREA WHEN HIS RIGHT FOOT GOT STUCK IN THE MUCK. HIS LEFT FOOT ALSO STUCK, CAUSIG N HIM TO FALL FORWARD. HE FELT A TEAR IN THE RIGHT KNEE AS HE FELL FORWARD.

HE WAS RAISING THE DOOR ON DERRICK SCREEN, COUNTER WEIGHT ON LID LOWERED, PINCHING FINGER BETWEEN THE LID AND THE WEIGHT. STITCHES PUT ON RIGHT MIDDLE FINGER TIP.

EMPLOYEE WAS LOADING THE FLOOR OF A BOXCAR WITH 100LB BAGS OF SILICA SAND.WHEN EMPLOYEE TURNED HIS BODY TO STACK BAG OF SAND ON THE FLOOR OF THE BOXCAR.HE FELT PAIN IN HIS NECK AND RIGHT SHOUL DER.

I.NAME WORKING W/SURVEYOR-CONTRACTED TO ESTABLISH SCENIC EASMENT AND PROPERTY LINES AT A FUTURE MINING SITE.AFTER GOING HOME FROM WORK 6-29,DISCOVERED A DEER TICK AND BITE ON RIGHT SHOULDER NE AR ARMPIT.CAUSED NO PROBLEMS UNTIL 7-12-91 WHEN STARTED EXPERIENCING SEVERE HEADACHE.THEN TAKEN TO EMERG RM 7-13.HAD APPLIED INSECT REPELLENT PROIR TO STARTING WORK 6-29-91.

I NAME WAS STANDING ON A LADDER REPAIRING A ROLLER ON A LARGE OVERHEAD DOOR ON THE MAINTENANCE SHOP A DO NOT OPERATE TAG WAS PLACE DON THE DOOR SWITCH BUT THE DOOR WAS NOT LOCKED OUT THE END L OADER OPERATOR HAD AN AUTOMATIC R EMOTE CONT ROLDOOR OPENER WHICH HE USED TO OPEN THE DOOR WHILE I NAME WAS WORKING ON IT INJURED GRABBED ONTO THE TOP OF THE DOOR AS IT OPENED WHEN THE DOOR H

ORIGINAL FORM WAS SENT ON 01-08-90 EXPLAINING THIS ACCIDENT A NEW FORM IS BEING SENT SINCE THIS HAS NOW TURNED INTO A LOST TIME AS OF SATURDAY NOVEMBER 10,1990.

CUTANEOUS SCLERODERMA

HE WAS CLIMBING OVER A ELECTRIC MOTOR, SLIPPED AND FELL APPROX. 2 FEET ON HIS BUTTOCKS. LOWER BACK PAIN.

EMPLOYEE WAS MOVING A PIECE OF 1/2" X 4' X 10' IU.H.M.W. PLASTIC SHEETING. PLASTIC SHEETING SLIPPED OUT OF CO-WORKER'S HANDS AND FELL ON INJURED'S FOOT. HURT GRAND RIGHT TOE.

OPERATOR WAS MOVING DRILL TO EDGE OF LEDGE.TO DRILL ANOTHER HOLE WHEN THER DRILL TRACK RAN OVER END OF SHOE CAUSING STEEL TOE TO BUCKLE AND CUT MIDDLE TOE.

I.NAME OPENING HOPPER LID FELT KNEE POP.USING PROPER LIFTING TECHNIQUES AND DIDNT KNOW WHAT HAPPENED.LID DIDNT SEEM TO BE STUCK IN ANY WAY.

I NAME WAS DOING HIS NORMAL JOB WAS REACHING FOR THE NEXT 100# BAG TO COME OFF CONVEYOR SOMETHING POPPED IN HIS LOWER BACK

EMPL WAS SPOTTING RAILCAR & WAS ADJUSTING LOADING SPOUT SPOUT CAUGHT ON CAR DOOR CAME LOOSE & CAUGHT EMPL AGAINST SHOULDER TWISTING.

EMPL WAS TRYING TO OPEN COFFIN TYPE HOPPER LI TO LOAD CAR WITH SAND. LID WAS STUCK EMPL PULLED TOO HARD TRYING TO OPEN.

EMPLOYEE WAS REMOVING TOOLS & EQUIPMENT FROM THE BUCKET OF A 941 CAT ENDLOADER EMLOYEES FOOT WAS UNDERNEATH A TOOTH OF THE BUCKET WHEN THE BUCKET SETTLED TRAPPING EMPLOYEES LEFT FOOT UNDER BUC KET AND BREAKING SMALL TOE

WHEN EMPL CAME BACK TO JAW SHACK, A 15' PIECE OF CONDUIT WITH LARGE WEATHER HEAD ATTACHED FELL OFF PLATFORM AT SIDE OF JAW SHACK, WEATHER HEAD STRUCK EMPL ON RIGHT FOOT AT BACK OF HIS SAFETY TOE, BREAKING HIS BIG TOE ON RIGHT FOOT.

I.NAME WAS TAKING OFF THE CONVEYOR COVER AND DIDN'T GET HIS FOOT OUT OF THE WAY, SETTING SHARP EDGE DOWN ON FOOT, CUTTING THROUGH BOOT AND CUTTING HIS FOOT.

EE WAS RETURNING TO WASH PLANT FROM ROUND BUILDING WHEN HE SLIPPED ON GRATING CAUGHT HIMSELF BY HANDRAIL BUT TWISTED BACK TRYING TO KEEP FROM FALLING.

HEADED OUT TO DREDGE.I.NAME HAD JUST COMPLETED RAISING SUCTION PIPE AND INDICATED HE WAS PUMPIN GCLEAR WATER.I.NAME MOVED TO REAR OF DREDGE TO ACTIVATE WINCH CONTROLS TO MOVE DREDGE.I.NAME STA RTED WINCH AND DREDGE MOVED A FEW FEET UNTIL CABLE SLIPPED ON DRUM.I.NAME STOPPED WINCH AND STARTED TO REVERSE WINCH.I.NAME LOOKED AT I.NAME,SAW DREDGE WAS TURNING OVER-YELLED TO I.NAME TO GE