Balcones Quarry Metal/Non-Metal

While cutting belt at tail pulley the blade slipped out and hit employees left arm. Left arm was positioned in a bad area when this happened. The cut was on EE's forearm 3 inches past base of thumb. Cut got fatty tissue and some mussel.

Electrician modifying a threaded nipple with portable bandsaw for conduit installation to transformer and lacerated EE's right middle fingertip.

Employee was removing a conveyer belt when the right outrigger on the forklift they were using shifted downward causing the forks to hit an electrical box where they had their hand. The impact caused a fracture / laceration to their left thumb.

Employee stepped on a concrete floor scraper causing the wooden handle striking their thumb on 4/4/2025, medical treatment was sought later on 4/15/2025 and they were diagnosed with a strain to the thumb and was placed on restrictions and physical therapy.

Employee opened a toolbox drawer when it fell down onto their right thumb and tool box door causing a fracture to their right thumb

EE was cleaning under a conveyor belt when EE stood on the bucket of the skid steer EE was operating. EE began to cut part of the belt and material fell on EE causing EE to lose EE's balance and fell aprox. 24 inches on EE's left side injuring EE's shoulder, left hip and rib.

Electrician was removing spillage buildup on a decommissioned (de-energized) cable tray which had collapsed. While working to pry and break spillage buildup, the material released causing EE to hit the side of their hand on metal box adjacent to cable tray smashing the right small finger (pinky) between the box and the tool handle.

Employee was cutting the old rubber endcaps off of the spray bars at the Wash Plant. While cutting one of them, the retractable-blade utility knife they were using slipped off the rubber and contacted their left inner thigh. This caused a laceration about 1 inch long and 1 inch deep. 3 Sutures required.

Employee was cleaning at the Water reclaim Plant (Sand Plant) and went to retrieve a water hose and slipped on wet slippery surface and twisted left knee.

Ladder not secured; working in awkward position

EMPLOYEE WAS CLEANING AROUND THE PRIMARY CRUSHER WHEN THEY SPRAINED THEIR ANKLE ON AN UNEVEN SURFACE.

Employee arrived to work, had parked car and was getting out when some debris in the wind entered their eye. They flushed eye but it didn't get better so they then notified management.

While working on a tire, the tire manipulator slipped catching the technicians thumb between the manipulator and the driver key the technician was holding in place by hand.

The EE placed right hand inside a pin hole to remove grease before installing a hammer attachment on an excavator. The hammer attachment slipped pinching fingers.

EE was in the process of driving T post when right thumb struck the top of the post while holding the post driver handle. The EE was wearing cut level 4 gloves at the time of the incident.

EE was going up in the man-lift basket and approaching the railing of the screen 3 and 4 deck. EE had EE's left hand gripping the handrail of the man basket, EE's middle two fingers were curled over the rail of the basket. EE leaned forward and pinched EE's two fingers between handrail of basket and handrail of wash plant.

Employee and witness were rolling a section of conveyor belt off a roll that is suspended on a set of I-beams with a 3" shaft. After cutting off the section needed they rolled the belt back up. The shaft fell off of the I-beam and struck employee on the shoulder, knocking them to the ground.

EE was removing barricade on a slight incline when EE slipped backwards. As EE was falling, EE placed hand behind to catch self. In doing this EE injured their finger on rocks in the area.

EE was performing maintenance at Wash Plant on C8 conveyor and wash screen 4 replacing a roller assembly. The assembly hit the handrail and caused it to rotate and pinching the EE's tip of ring finger between the roller assembly and tail pulley frame, causing a laceration to the finger.

The mounting plate for the Secondary Crusher (deflector plate) had built up material behind it creating a force on the plate. When the end of the plate was cut loose from the crusher housing, the plate rapidly released this tension like a spring and swung out impacting the mechanic. The mechanic suffered 2 lacerations on the face and as EE fell back landed on the tail bone.

EE had a tool in a portable vise on the back of a utility truck. Upon pressing with both hands on the lever to release the pressure of the vise it suddenly broke loose and EE put force on the inside of EE's right ring finger causing a fracture.

Employee called and stated they were working at cemex quarry pulling product (caps) from magazine and felt a sharp pain in back.

Employee was cleaning out a conveyor chute when EE reached down onto the flow of material to turn on a water valve and was struck on the right pinky finger by a 5 - 10" rock.

EE works the evening shift and the injury occurred around 4am. The employee was shoveling material out from under a conveyor belt when ee hit a hard spot in the material and felt pain in elbow. The employee was taken to minor emergency. EE was released back to work with non-prescription medication and restrictions of motion to the right arm.

While lugging on a tire, tech was using crane hands to line up tire with bolt holes. Guiding tire into place ee applied down pressure on tire. The tire slipped in the loose gravel causing the boom to surge forward hitting the tech in back, causing ee to lose breath and pain in the lower back.

Employee was moving the chocks on a radial stacker and was bumped by another employee who was operating the skid steer. Employee thought EE was OK but EE went to the doctor the next day and had a hairline fracture to one rib.

Employee was changing out hammers on the crusher. He put one of the old hammers on the ground and left it standing up. it fell over and hit his foot behind his steel toe on top of his foot.

IW was standing on ladder installing a part on a 777 truck bed using truck hoist. IW thought brackets were engaged (not visible while mounting part) so released tension from hoist. Using a hammer to knock part down better bracket came loose and fell knocking the ladder out from IW. IW fell to ground catching self with right arm causing injury to right arm and shoulder

The employee was shoveling on the 10th, felt pain at end of shift, Employee worked until the 28th. At that time he came to the supervisor saying it had been hurting since the 10th and that he thought he could work through it. The employee was diagnosed with shoulder strain.

The employee stated that after climbing down the ladder of the water truck, when he went to turn to go to the back of the truck his leg planted when he twisted and he went to the ground hearing a pop in his knee. He refused to go to the doctor that day and on 12/1/2014 he asked for medical treatment and was diagnosed with a Sprain on his right knee with work restrictions.

ELECTRICIAN SUFFERED FLASH BURNS TO THE NECK AND HAND WHEN HE WAS INSTALLING AN ELECTRICAL BOX THAT CAME IN CONTACT WITH AN ENERGIZED BUSS BAR.

The water truck door was opened the EE was reaching in to get his gloves when the door shut pinching his right ring finger.

Contractor Vehicle eletrical fire

EE was lifting at work and strained low back. He experience pain and was taken to Texas Medical Clinic. He was given prescriptions and light duty. EE returned a week later for follow-up and was feeling much better and able to touch toes.

Dizzy feeling, heart racing, feels weak, feels worse after eating, dehydration from working in extreme heat. Effects all over body. No equipment, nothing directly/indirectly effected this employee.

Driller said the wind blew door of drill shut on his hand. Crushed the end of his right index finger.

LOADER STRUCK RAILCAR WHILE CLEANING MATERIAL AROUND TRACK.

STRUCK IN HEAD BY FALLING ROCK.

SPRAYING OFF CATWALK, NEEDED TO SHUT WATER OFF, PLACED HOSE DOWN WENT TO THE SHUT OFF THE VALVE QUICKLY AND TWISTED RIGHT ANKLE.

EE WAS SETTING MOTOR DOWN TO GET READY TO INSTALL THE MOTOR, IT SLIPPED, EE REACHED FOR IT AND RIGHT SHOULDER POPPED.

Driller was checking hole depths. He slipped and fell. Slipped on rocks around hole

TRYING TO SHUT A DOOR TO THE FEEDER USING A HAMMER AND HIT FINGER.

EE was working on the VSI to remove the table and had the crane attached to the table. The table was broken loose with a hyd jack and when pressure was taken off the jack, the table went down on the shaft. As the crane applied pressure, the table jerked off the shaft and rotated catching EE's foot against an anvil in the VSI.

EE was removing a bearing from a piece of machine when it slipped and cut his left thumb.

While bent over and unaware of a piece of metal, the EE walked into it causing a laceration to the face.

EE cleaning chute with a scraper bar when he felt a sharp pain in his right shoulder.

Employee kneeling down welding steel for a junction box, gust of wind blew something in his eye.

EE was shoveling in tunnel, lifted shovel up and turned, felt sharp pain in back.

EMPLOYEE WAS CUTTING THE RIDING BAND. WHEN HE LOOKED UP, LIME DUST FELL IN HIS EYE.

EE was removing a blockage in the #2 chute, hand slipped causing the right ring finger to get lacerated, requiring seven stitches ( SUTURES ONLY).

Employee stated he was climbing up a step ladder when he fell off the ladder resulting in a right knee sprain. Underwent arthroscopy right knee surgery on 1/16/2008.

Employee was being familiarized on a loader, when he stood up employee felt pain in his lower back. As a result employee sustained a lumbar spine sprain. Medical Treatment Only - Physical therapy starting on 8/17/07; 6 sessions, 2 per month for the next three months.

Employee was cutting skirt rubber, blade slipped, cutting left hand between thumb and forefinger, requiring stitches.

Employee fell off of ladder while patching a scurry line hitting left elbow on angle support structure.

While cutting rusty metal with a cutting torch, a piece of slag flew into the employee's left eye.

When employee was pulling come along he caught his left thumb between the guard and shift. This resulted in a hairline fracture to his left thumb.

EMPLOYEE WORKING AT SECONDARY PLANT, PUSHING ROTOR, HIS HAND SLIPPED OFF & WAS CAUGHT BETWEEN THE HAMMER & WALL. EE RECEIVED 13 STITCHES ON HIS RING FINGER ON HIS LEFT HAND.

STANDING, LOOKING UP TRYING TO DISCONNECT COUNTERWEIGHT ON C9 WHEN MATERIAL FELL OFF OF THE CONVEYOR AND INTO EE'S EYE.

EMPLOYEE WAS CLEANING UNDER CONVEYOR BELT FEEDING ALPHA BLENDING PLANT. THE CONVEYOR FEEDING THE PLANT RAN EMPTY WHEN FEED WAS STOPPED, RESULTING IN ONE ROCK TUMBLING BACKWARDS DOWN THE BELT AND STRIKING EMPLOYEE ON THE LOWER BACKSIDE OF THE RIGHT SIDE OF HIS HEAD. REQUIRED FIVE STAPLES.

EE GETTING IN POSITION TO CUT BELT, LANDED ON A ROCK CAUSING HIM TO JERK KNIFE BACK AND AWAY FROM BELT, CATCHING HIS LEFT INDEX FINGER. REQUIRED NINE STITCHES.

EE BECAME DIZZY, LOST HIS BALANCE AND FELL DOWN THE STAIRS IN THE SHOP SUSTAINING A LACERATION TO HIS LEFT KNEE. REQUIRED LIGHT STITCHES.

EE WAS CUTTING CONVEYER BELT, KNIFE SLIPPED LACERATING HIS RIGHT THIGH.

BREAKING OFF FLEXCO BOLTS WITH BREAKER BAR AND HEARD POP IN LEFT ELBOW. ARM STARTED HURTING AFTERWARDS.

EMPLOYEE WAS CLEANING THE CATWALK WHEN A ROCK FELL OFF THE BELT STRIKING HIS LEFT CHEEK.

THE EE WAS MOVING A FEEDER BLOCK WITH A PIPE. HE SLIPPED AND SMASHED HIS LEFT FOURTH FINGER BETWEEN THE PIPE AND THE FEEDER BLOCK. HE SUSTAINED A CONTUSION.

LACERATED RIGHT HAND ACROSS THE PALM AND RIGHT INDEX FINGER. HE WAS MEASURING BEAM ABOVE PULLEY WHILE BELT WAS MOVING WHEN THE TAPE MEASURE GOT CAUGHT IN PULLEY GRABBING HIS HAND AND CUTTING I T TO THE BONE. HE HAS TO HAVE SURGERY TO REPAIR NERVE DAMAGE.

WHILE WORKING IN AN AREA USED FOR WELDING PREPARATION EE FELT AN INSECT STING AND CONTINUED TO WORK THINKING NOTHING MORE OF IT. EE FINISHED HIS SHIFT AND THE NEXT. HE REPORTED THIS TO HIS SUP ERVISOR. HIS SUPERVISOR IMMEDIATELY SENT HIM TO THE DOCTOR. THE RESULTING STING SITE HAS GOTTEN BADLY INFECTED AND NOW REQUIRES FURTHER MEDICAL ATTENTION.

WORKING ON SCREEN, DOOR FELL ON EMPLOYEE, BRUISING NECK.

EE WAS WORKING ON THE DREDGE (WELDING) WHEN AN INSECT CRAWLED INTO HIS BOOT AND BIT HIM ON THE ANKLE. HE DID NOT SUFFER ANY PAIN UNTIL WORKING THE NEXT DAY AND AT 5:20 PM HE ALERTED MYSELF THE QUARRY MANAGER AND I IMMEDIATELY SENT HIM TO THE DOCTOR. HE WAS ABLE TO RETURN ON THE 7TH OF OCTOBER & DID RESUME FULL DUTIES. HE DID NOT RETURN THE NEXT SHIFT AS DR TOLD HIM NOT TO WEAR BOOT

LIFTING SCREEN FROM CATWALK: IN THE PROCESS HIS LEFT HAND CAME INTO CONTACT WITH THE HANDRAIL, SMASHING FINGER WITH SCREEN AGAINST RAIL.

CHANGING SCREEN, PULLING SCREEN FROM SHAKER, HE PULLED A MUSCLE IN HIS BACK.

SPIDER BITE - WORKING ON PRIMARY BELT.

PUTTING GUARD ON C11 CONVEYOR & WAS BITTEN.

JACK SLIPPED & SPRINGS CAUGHT FINGER.

HE PULLED MUSCLE IN LEFT LEG/HIP WHILE SWINGING SLEDGE HAMMER WITH FULL BODY WEIGHT.

LOOSENING COMEALONG, IT GAVE WAY SENDING MOTOR FRAME DOWN TOO QUICK TO RESPOND.

STRAINED ELBOW LIFTING & PULLING SCREENS.

CUTTING GREASE LINE WITH A UTILITY KNIFE, KNIFE SLIPPED AND CUT HIS HAND, REQUIRING FOUR STITCHES.

SHOCK ON FUEL TRUCK SEAT IS BROKEN CAUSING HIS BACK TO BE JARRED.

MAKING A RAMP ON AGGREGATE PILE, WHEN HE PUT THE 926 LOADER IN REVERSE HE HIT A HOLE WITH A TIRE AND IT CAUSED HIS HEAD TO SNAP BACK HE THEN FELT A PAIN IN HIS SHOULDER AND BACK AREA ON RIGHT SIDE.

PROCEEDED TO CLIMB ON EAST OF FEEDER #4, SHOULD HAVE CLIMBED ON NORTH SIDE OF FEEDER INSTEAD WHEN CLIMBING DOWN ON EAST SIDE, SLIPPED AND RIGHT FOOT CUGHT IN HEAD PULLEY.

THE TRUCK DRIVER WAS CLIMBING ONT O THE TRUCK, HE LOST HIS FOOTING CAUSING HIM TO COME DOWN AD HITTING HIMSELF. ON THE FRAME PART OF THE STEPS ON HIS RIB CAGE, ALSO SCRAPE HIS LEG AND ELBOW CR .

THE OPERATOR WAS COMING OUT OF THE CONTROL HOUSE WHEN HE HIT HIS HAND ON THE LIGHT SWITCH THE CORNER HAD A SHARP EDGE ON IT CAUSING THE INJURY. THIS PROBLEM HAS BEEN TAKEN CARE OF.

MAN STANDING ON ROTAR-CLEANING BOULDERS AND MUD FROM BETWEEN THE ROTAR AND CRUSHER BACKWALL. WHEN ROTAR BROKE FREE AND STARTED TO ROTATE, HE STARTED TO STEP OFF ROTAR WHEN HE GOT FOOT CAUGHT.

OPERATOR ERROR. OPERATOR WAS NOT PAYING ATTENTION TO FLAGMAN OR EXISTING TRAFFIC CONDITIONS. WE ARE NOT AWARE OF ANY PERMANENT IMPAIRMENT AS A RESULT OF THIS ACCIDENT.

CEMEX CONVEYOR WAS SPILLING MATERIAL SO EE WENT TO TUNNEL #5 TO PICK UP ANOTHER EE TO ADJUST CONVERYOR AND LEGGING ON SKIRTBOARD. EE PUSHED LEGGING BACK IN PLACE AND EE TOLD OTHER EE TO GO UND ER THE CONVEYOR TO ADJUST A RETURN ROLLER. EE FOLLOWED INSTRUCTION TO HIT ROLLER WITH HAMMER AND GOT PULLED BETWEEN ROLLER AND CONVEYOR.

EE WAS WALKING OUT OF CONTROL HOUSE ONTO CATWALK. HE STEPPED ON A ROCK TWISTING HIS RIGHT ANKLE.

EE WAS GREASING ROLLERS ON #5 FEEDR BELT. HE MISSED THE ROLLER GREASE UNDER WHILE TRYING TO CORRECT & T0 GREASE GUN, HIS GLOVE CAUGHT BETWEEN BELT AND ROLLER PULLING AND SMASHING HIS HAND AND FINGERS BETWEEN

EE WAS CLEANING A CHUTE ON WEST SCREEN WHEN A PIECE UP ABOVE BROKE LOOSE HITTING HIS WRIST.

EE WAS TRIMMING A PIECE OF CON EYOR BELT AND STUCK BLADE INTO LEG REQUIRING STITCHES.

EMP WAS CLEANING WEST CHUTE OF SECONDARY PLANT WITH ELECTRIC CHISEL WHEN ROCK FELL FROM TOP FROMVIBRATION HITTING HIM ON WRIST.

EE WAS HITTING ON A BEARIING RACE AT THE CONE PLANT WHEN A PIECE CHIPPED OFF HITTING EE IN ARM CAUSING A PUNCTURE. ANTIBIOTIC & ANTIINFLAMINATORY PRESCRIPTION GIVEN.

WHILE TRYING TO JUMP START UNIT 252 (35 TON TRUCK) THE BATTERY EXPLODED. EMPLOYEE GOT HIT IN THE FACE. HE WAS TAKEN TO ER TO BE CHECKED. THE DR. PRESCRIBED EYE DROPS FOR HIS EYE TO KEEP IT MOI ST.

EE WAS CLEANING BUILDUP MATERIAL ON C-70 BEWLT. SECOND ROLLER FROM BACK WHEN HE STARTED HITTING ROLLER WITH HAMMER. THE BELT CAUGHT THE HAMMER PULLING HIS HAND BETWEEN ROLLER AND SKIRTBOARD.

WHILE LOOSENING HYDRAULIC TANK BOLT ON UNIT 239, BOLT BROKE LOOSE JAMMING HAND AND PUTTING ABRASION ON THUMB. THE THUMB BECAME INFECTED. PLACED ON LIGHT DUTY.

WHILE DIGGNG OUT CRUSHER LINER TO REMOVE, HELPER DROPPED LINER IN EE'S ARM, CAUSING A BREAK.

WHILE WORKING ON BRASS BOWL INTO SOCKET ASSEMBVL, SLEDGE HAMMER BROKE AND HAND HIT BOWL. EE WENT TO DR THAT DAY, BUT DR SAID IT WAS A CONTUSION. ON 3-29-95 EE ASKED TO GO TO ANOTHER DR AS HAND WAS STILL HURTING. SECOND DR FELT THERE WAS A HAIRLINE BREAK IN HAND, MAKING THIS A DR TREATED CASE.

EMPLOYEE WAS MOVING NEW CONVEYOR INTO POSITION ON CATWALK AT THE BLENDING SYSTEM WHEN HIS FINGER JAMMED BETWEEN ROLL OF BELT AND ELECTRICAL CONDUIT STRAP.

INJURED WAS TIGHTENING WEDGE WITH SLEDGE HAMMER. AS HAMMER MISSED WEDGE, HE FELL FORWARD AND STRUCK MOUTH ON FRAME WORK OF CONE CRUSHER.

INJURED WAS DRIVING COTTER PIN WITH HAMMER AND SCREWDRIVER. HE MISSED SCREWDRIVER WITH HAMMER AND STRUCK HIS FINGER.

INJURED WAS HELPING TO HANG CHUTE ON CONVEYOR, WHEN SOMETHING GOT INTO LEFT EYE.

NO KNOWN NEW EVENT OCCURRENCE OR ACCIDENT EE CONTINUES TO HAVE WEEK PAIN POSSIBLY RELAT ED TO HIS INJURY OCCURING ON 04-23-93

INJURED WAS WORKING INSIDE CHUTE, WHEN TORCH HOSE CAUGHT FIRE INFLICTING BURN ON LEFT SIDE OF NECK.

INJURED WAS STEPPING OFF BOTTOM STEP ONTO FEEDER PLATFORM WHEN HE TWISTED HIS LEFT ANKLE

INJURED WAS HELPING TO CHANG ESHAKER SCREEN. OTHER EMPLOYEE MOVED THE SCREEN AND LOST HIS GRIP WHILE INJURED HELD ON THE FALLING SCREEN PULLED ON HIS SHOULDER.

INJURED WAS REMOVING OLD VALVE OFF TUBE WITH TORCH TORCH MELTED INSIDERUBBER AND IT BLEW HOT GAS AND MELTED ALUMINUM ON HIS HAND.

INJURED WAS OPENING DOOR ON ROLL CRUSHER WHEN HIS FINGER WAS MASHED BETWEEN PIPE AND GUARD.

INJURED HAD PLACED CHAIN AND COM A LONG IN BACK OF FOREMANS PICK UP AS HE CLIMBED STIARS TO CRUSHER HE FELT PAIN IN LOWER BACK.

INJURED WAS CUTTING CONVEYOR BELT WHEN BELT KNIFE SLIPPED AND HE CUT HIS THIGH.

INJURED WAS SHOVELING IN AGGREGATE TUNNEL; WHEN HE FELT A POP IN RIGHT SHOULDER.

INJURED'S FOOT FLIPPED WHILE DESCENDING DUST COLLECTOR LADDER. HE PREVENTED A FALL FROM THE LADDER BY HOLDING TIGHTLY WITH HIS RIGHT HAND. HOWEVER, THE EXTRA WEIGHT ON THE RIGHT ARM CAUSED A STRAIN.

INJURED WAS HELPING TO CARRY CONVEYOR ROLLERS UPCATWALK;LATER HE FELT PAIN IN UPPER BACK DOWN TOLOWER BACK. EMPL DID NOT REPORT THIS UNTIL 5/21/93.EMPL HAD BEEN GIVE 8-10 DAYS OF LIGHT DUTY; BUT NOW FULL RELEASE DATE UNKNOWN.

INJURED WAS REMOVING BELT CLAMP OFF OF CONVEYOR; WHEN HE FELT PAIN IN LOWER BACK.

INJURED WAS LOOSENING BOLTS ON V-BELT GUARD, WHEN A BOLT BRAKE, RATCHET HIT HIS TOOTH.

INJURED WAS OPERING CHUTE ROLL AWAY BOX WITH A COME A LONG WHEN HE PULLED ON COME A LONG HE FELT PAIN IN LEFT SHOULDER.

INJURED WAS STEPPING OVER WELDING/TORCH CABLES HANGING OVER CATWALK AND STEPPED DOWN ON SAFETY BELT LYING ON CATWALK AND TWISTED HIS LEFT ANKLE.

INJURED WAS GOING UP TO CHECK DEWATERING SCREENS. THERE WAS WATER IN FRONT OF LADDER. HE STEPPED OFF TO SIDE OF LADDER AND SLIPPED IN MUD. (HIS STEEL TOED BOOTS HAD HOLES AND WOULD HAVE LEAKED IN WATER. HE HAS REPLACED THE BOOTS).

INJURED WAS HELPING REPLACE A FEEDER BELT AND BELT GUARDS. OTHER EMPLOYEES WERE USING HAMMERS TO FIT GUARDS.

INJURED WAS SHOVELING IN TUNNEL. HIS SHOVEL STRUCK MOVING CONVEYOR, CAUSING SHOVEL HANDLE TO STRIKE FACE.

ON 01-06-92 INJURED WAS HELPING INSTALL SHAKER SCREENS SOON AFTER HE FELT PAIN IN RT LOWER BACK HE DID NOT TELL HIS FOREMAN ABOUT INCIDENT ON 01-09-92 HE WAS CHANGING SCFREENS AGAIN & FELT PAI N SOON AFTER HE THEN TOLD HIS FOREMAN ABOUT BOTHINCIDENTS

INJURED WAS STRETCHING TO SPLICE CONVEYOR BELT AND FELT PAIN IN LEFT SIDE.NOTE HE HAD BEEN ASSAULTED OFF THE JOB ON 11-30-91.BADLY BRUISED LEFT SIDE.

POSSIBLE AGRAVATION OF ALLEGED INJURY OF 04-21-91,05-15-91 OR 10-11-91. NO NEW INJURY.INJURED WORKED 1 1/2 HOURS ON 11-13-91 AND SAID HE NEEDED TO GO HOME.HE ALSO,CLAIMED HE HAD BEEN HURTING S INCE HE RETURNED TO WORK ON 10-28-91.WE THOUGHT HE WOULD HAVE BEEN BACK A LONG TIME AGO,BUT HE HAS NOT YET BEEN RELEASED BY THE DOCTOR.

INJURED WAS CHECKING SHAKER SCREEN WHICH HAD BEEN LOCKED OUT. HE GRABBED V-BELTS NEAR THE SHEAVE AND WHEN THE SCREEN SHAFT RELEASED, IT DREW HIS HAND INTO THE PINCH POINT BETWEEN THE V-BELTS A ND THE SHEAVE.

INJURED WAS HELPING TO UNHOOK CABLE FROM TRUCK;AS HE THREW CABLE OFF TO THE SIDE,HE FELT PAIN IN BACK.

THE LAST DAY HE WORKED PRIOR TO A ONE WEEK VACATION, WAS 6/28/91. HE WENT TO THE DR. ON 7/8/91 FOR CRACKED SKIN ON HANDS AND FEET. HE RETURNED TO WORK ON 7/9/91. HE DID NOT TELL US THAT THE DR . VISIT WAS WORK RELATED UNTIL 7/10/91.

INJURED WAS CUTTING WEEDS WITH WEEDEATER AT FRONT ENTRANCE. ABOUT 30 HOURS LATER HE WENT TO THE EMERGENCY ROOM FOR RASH ON HIS FACE; HE DID NOT TELL US UNTIL THE NEXT DAY.

EE TOLD FOREMAN THAT HEHURT HIS BACK WHEN HE TURNED AFTER HE PUT HIS LOCK ON HIS TOOL BOX LATER THAT MORNING EE TOLD DR HOLTMAN AND HE HURT HIS BACK INSTEAD AT 400 AM 5-15-91 WHILE HE WAS USIN G A SLEDGEHAMMER AND PRYBAR.

INJURED ALLEGEDLY HURT HIS LOWER BACK AFTER SHOVELING OFF CONVEYOR BELT.HE DID NOT TELL ANYONE ABOUT ALLEGED INJURY UNTIL 05-07-91.

INJURED WAS USING A HAMMER TO DRIVE WEDGES INTO ADJUSTMENT LOCK POST ON 7' CONE CRUSHER. THE HAMMER SLIPPED STRIKING HIS RIGHT INDEX FINGER CAUSING A SLIGHT FRACTURE TO THE FINGER TIP BONE.

INJ WAS CLEARING BRUSH FROM ENTRANCE OF PLANT. SEVERAL DAYS LATER INJ BEGAN TO BREAK OUT ON FACE HANDS FOREARMS WITH ITCHING

INJURED WAS HELPING WELDER PUT LOGGING ON HEAD PULLEY. LATER THAT NIGHT HE WOKE UP WITH BURNING EYES.

EMPLOYEE WAS ADJUSTING BELT SCRAPER TENSION WHEN THE HANDLE "KICKED" BACK CATCHING HIS FINGER BETWEEN THE HANDLE AND A LOCK DOWN HOOK.

INJURED WAS TIGHTENING EAST DYNAPACTOR MOTOR BY PUSHING DOWN ON WRENCH WITH HIS LEFT FOOT, WHEN HE FELT PAIN IN LOWER BACK.

INJURED WAS HELPING TO MOVE LARGE WOODEN SHELVES WHEN SHELF LEGS BROKE AND FELL OVER INJURED.

INJURED WAS CUTTING A FRAYED PIECE OF CONVEYOR BELT OUT WHEN THE KNIFE PULLED LOOSE AND CUT HIS RIGHT FOREARM.

INJURED WASSTEPPING DOWN FROM LADDER & TWISTED RIGHT ANKLE ON LOW PLACE OF CATWALK.

ALLEGEDLY INJURED WAS OPENING SAND DOOR IN MAIN TUNNEL, PRYBAR SLIPPED, HE FELL AND STRUCK HIS LEFT SIDE ON STEP.

HE ALLEDGEDLY GOT INTO POSION IVY WHILE CLEANING UP FRONT ENTRACNE OF PLANT. HE WENT TO THE EMERGENY ROOM TWICE BEFORE TELLING US THE FULL STORY. THE RASH ALSO COULD HAVE BENN A GROIN RASH S PREAD BY POOR PERSONAL HYGENE AND WASHED CLOTHES.

INJURED WAS WASHING OUT SAND BIN WITH WATER HOSE WHEN DIRT FLEW INTO LEFT EYE.

INJURED WAS STEPPING OFF OF LOADER, WHEN HE STEPPED IN A MUD HOLE AND TWISTED HIS RIGHT ANKLE.

INJURED ALLEDGEDLY HURT BAC WHILE DRIVING HAUL TRUCK OVER ROUGH ROAD.

INJURED WAS USING SLEDGE TO STRIKE A PIPE WHICH HE WAS HOLDING IN HIS LEFT AHND.HE MISSED THE PIPE AND STRUCK HIS LEFT FIRST FINGER.

FELT PAIN IN BACK HANDLING GREASE DRUMS.RX DRUGS ISSUED.

INJURED WAS PICKING UP FIRE EXTINGUISHER,WHEN CUT RIGHT FINGER ON EXTINGUISHER HANDLE.PRESCRIPTION DRUGS WERE ISSUED.

BEING SUBMIT. BECAUSE EMP ALLEDG. MISSING TIME AGAIN BECASUE OF PREV INJ WHICH OCC ON 9-26-89.

INJURED WAS INSIDE DYNAPACTOR THROWING ROCKS TO THE OUTSIDE, WHEN HE FELT PAIN IN LOWER BACK. (PRESCRIPTION DRUGS WERE ISSUED)

INJURED FELT PAIN IN LEFT SHOULDER WHEN HE WAS PULLING ON FIRE HOISE TO WASH OFF STACKER TRACK.

INJURED WAS STRICKING CHUTE WITH SLEDGE HAMMER, WHEN RIGHT MIDDLE FINGER WAS CAUGHT BETWEEN HANDLE AND CHUTE FRAME.

INJURED WAS CLIMBING DOWN LOADER LADDER, STEPPED ON MUD CLOD AND TWISTED LEFT ANKLE.

INJ GOING UP LADDER TO HAMMERMILL WHEN HE MISSED STEP AND RIGHT LEG WENT THROUGH LADDER RUNGS.RX DRUGS ISSUED.

INJURED WAS CLEANING UNDER CONVEYOR BELT WITH HAND SHOVEL WHEN HE FELT PAIN IN LOWER BACK

INJURED WAS WALKING DOWN STEPS WHEN HE MISSED THE LAST STEP AND TWISTED HIS BACK. (PRESCRIPTION DRUGS WERE ISSUED.)_

ALLEDGEDLY INJURED WAS SHOVELING UNDER MAIN CRUSHER; WHEN 8" ROCK FELL DOWN AND STRUCK TOPSIDE OF ARM ABOVE RIGHT WRIST. (PRESCRIPTION DRUGS WERE ISSUED).

INJURED WAS LOWERING TRUCK WINDOW, IT SLIPPED AND CAUGHT TIP OF 1ST FINGER RIGHT HAND. NOTE: HE RECEIVED TETNUS SHOT AND DEBRIDEMENT OF SKIN (1/4" X 3/8")

INJURED HAD LIFTED 5 GAL BUCKET OF ROCK OIL.AS HE WAS POURING INTO DRILL TANK,HE FELT PAIN IN LOWER BACK.PRESCRIPTION DRUGS WERE ISSUED.

EMPL ALLEDGES THAT EH STRAINED LEFT SHOULDER WHILE SHOVELING IN AGGREGATE TUNNEL ON 4/12/89. HE FELT NO PAIN UNTIL HE GOT UP ON MORNING OF 4/13/89. HE KNOWS OF NO SPECIFIC INCIDENT THAT INFLIC TED INJURY. HE WORKED ALL DAY 4/13/89 & UNTIL NOON ON 4/14/89 AT WHICH TIME HE TOLD HIS FOREMAN THAT ARM HURT & HE WANTE TO GO TO DR.

HURT R. ELBOW WHIEL SHOVELING UNDER CRUSHER.

INJURED WAS CLEANING DIRT OFF COUNTER WEIGHT PULLEY WHEN FINGER WAS CAUGHT BETWEEN BAR & GUARD FRAME.

INJURED WAS MOVING CHAIN GUARD WHEN SHARP EDGE CUT SMALL RIGHT FINGER.

INJURED WAS SHOVELING ON CONVEYOR BELT WHEN HE ALLEDGEDLY STRAINED HIS RIGHT ELBOW.

INJURED WAS EXITING TUNNEL WHEN HE TWISTED HIS RIGHT ANKLE.

INJURED WAS OPERATING A CAT D-7 DOZER HE BACKED OVER A SMALL HUMP CAUSING THE MACHINE TO JERK WHICH IN TURN INFLICTED A SLIGHT WHIPLASH INJURY TO HIS NECK

ALLEGEDLY INJURED WAS SHOVELING IN TUNNEL WHEN HE SLIPPED ON CONCRETE FLOOR AND RIGHT LEG SLIPPED OUT.

INJURED WAS WALKING DOWN LADDER AND SLIPPED CAUSING PAIN IN MIDDLE BACK..

INJURED WASS WORKING UNDER TUCK FROM INSIDE GREASE PIT. HE BENT DOWN & STEPPED ON AIR IMPACT HOSE. AIR IMPACT SLIPPED OFF OF CONCRETE SIDE OF PITY & STRUCK INJURED'S HEAD.

HE WAS CLEANING ROCKS FROM FEEDER SLIPPED & FELL ON LEFT HAND.

INJURED WAS MOVING ROLLAWAY CHUTE USING PIPE AS PRY BAR. PIPE SLIPPED & S TRUCK RIGHT KNEE.

INJURED HAD OPENED DOOR ABOVE CHUTE HE BENT OVER TO PICK UP BAR AS HE STOOD UP HE STRUCK BACK ON DOOR EDGE.

INJURED WAS ATTEMPTING TO PICK UP LARGE HYDRAULIC CYLINDER WITH STEEL PLATE ATTACHED HE CU T FINGER ON BURR ON PLATE

REOCCURING SWELLING & PAIN WHILE OPERATING DRAGLINE. INITIAL INJURY ON 8/9/88 WITH MUDDY BOOTS HE SLIPPED OFF DRAGLINE TRACK & STRUCK LEFT SHIN ON TRACK.

INJURED WAS BREAKING BOULDERS WITH DROPBALL CRANE HE CLIMBED DOWN TO MOVE ROCKS IN FRONT OF TRACKS THE GROUND WAS MUDDY AFTER A RAIN AS HE CLIMBED BACK UP HE SLIPPED ON TRACK AND STRUCK LE FT SHIN

INJURED WAS HELPING TO INSTLL BOLTS IN SHAKER SCREEN BEARING. BOLTS WERE SOAKING IN KLEAN SOLVENT. INJURED WIPED SWEAT OFF HIS FACE. DURING THE AFTERNOON HIS FACE STARTED BURNING.

INJURED WAS STADING ON DOZER BLADE HE SLIPPED OFF AND STRUCK WRIST ON BLAD ARM THIS FORM BEING SUBMITTED AS RESULT OF PART 50 AUDIT PRESCRIPTION DRUGS WERE ISSUED

INTINAL INJURY WAS ON 6-29-88. SMALL PIECE OF METAL STRUCK LEFT HAND.

INJURED WAS REMOVING SIMPLICITY BEARING WITH HAMMER AND CHISEL, WHEN SMALL PICEC OF METAL STRUCK LEFT HAND.

EMPLOYEE WAS SHOVELING UNDER CRUSHER WHEN A ROCK FELL DOWN AND STRUCK HIS LEFT SHOULDER

INJURED SLIPPED WHEN ENTERING TUNNEL AND STRUCK LEFT KNEE ON CONVEYOR SUPPORT FRAME.

INJURED WAS HELPING TO PULL TOGETHER FEEDER PADS WITH COME A LONG WHEN A WELDED EYE BROKE OFF FEEDER PAD AND STRUCK HIS LEG AND WRIST.

INJURED WAS STEPPING OFF WATER TRUCK LADDER WHEN HE SLIPPED OFF BOTTOM CHAIN STEP AND FELL TO GROUND THIS FORM BEING SUBMITTEED AS RESULT OF PART 50 AUDIT PRESCRIPTION DRUGS WERE ISSUED

INJURED WAS USING FIRE HOSE TO SPRAY SLIPPING BASE FEEDER HE STEPPED ON SUMP PUMP PIPE SLIPPED OFF AND FELL STRIKING REAR END ON CONCRETE FLOOR

EMPLOYEE WAS WALKING ACROSS SHOP FLOOR WHEN HE FIRST NOTICED SOMETHING IN HIS LEFT EYE. HE HAD PREVIOUSLY CHANGED AN OVERHEAD LIGHT IN A TUNNEL WHERE THE FOREIGN OBJECT PROBABLY GOT IN HIS EYE

AT APPROXIMATELY 8:20 AM ON MARCH 15,1988 GILBER BASS, A PARKER BROTHERS EMPLOYEE WAS INJURED IN A FALL AT THE NEW BRAUNFELS QUARRY.INJURIES ARE EXTENSIVE INVOLVING THE HEAD AND NECK AND HE RE MAINS HOSPITALIZED IN SAN ANTONIO TEXAS. ON MARCH 14 THE OPERATOR OF THE DRAGLINE USED A DROP LINE OPERATION TO BREAK BOULDERS,HAD RAISED THE CABLE TOO MUCH CAUSING THE SLEEVE ABOVE THE DROP

INJURY OCCURRED ON 3-14-88 WHEN A BELT CLAMP SLIPPED AND STRUCK INJUREDS RT KNEE THERE WAS NO LOST TIME APPROX 2 MONTHS LATER INJURED HAD SURGERY ON HIS RT KNEE TO RELIEVE PAIN LOST TIME STAR TED 5-24-88 ON 6-15-88 AND 9-21-88 INJURED HAD FURTHER SURGERIES TO REPAIR SURGERY DONE ON 4-21-87 THE SURGERY DONE ON 4-21-87HAD BEEN FOR AN INJURY TO HIS RT KNEE ON 9-23-86

INJURED WAS REMOVING SHAKER SCREEN COUNTERWEIGHT WHEN IT FELL DOWN IT BOUNCED AND STRUCK LEFT FOOT.

WHILE INSTALLING TRACKS ON LOADER INJURED WAS SWINGING SLEDGEHAMMER AND FELT PAIN IN L LOWER BACK THIS FORM BEING SUBMITTED AS RESULT OF PART 50 AUDIT PRESCRIPTION DRUGS WERE ISSUED

INJURED WAS OPERATING LIMA CRANE AS HE PULLED ON THE DRAG BUCKET LEVER HE FELT PAIN IN BACK THIS FORM BEING SUBMITTED AS RESULT OF PART 50 AUDIT PRESCRIPTION DRUGS WERE ISSUED

INJURED WAS COM3NG OUT OF HAMMERMILL, WHEN HE STRUCK HIS FOREARM ON INSIDE DOORWAY.

INJ SHOVELING I3 TUNNEL FELT APIN IN RIGHT SHOUDLER.

INJURED WAS SHO5ELING UNDER HAMMERMILL; WHEN JUNCTION BOX COVER FELL AND STRUCK HIM ON LEFT SHOULDER.

INJURED WAS DRI5ING PIN IN FEEDER PAD WITH BAR LATER HE FELT BACK PAIN

INJURED WAS ATT9MPTING TO PUSH A PARTIALLY STUCK CAROSEL LATCH PIN WITH A HAMMER HANDLE.WHILE PUSHING ON THE PIN WITH THE HAMMER HANDLE HE SIMULTANEOUSLY ACTIVATED CAROSEL CONTROL.THE HAMMER HANDLE WAS SPUN3AROUND AND HIS FINGER WAS PINCHED BETWEEN THE HANDLE AND THE CAROSEL FRAME.

SHOVELING IN TU3NEL FELT PAIN IN UPPER BACK.

INJURED WAS BUR3ED BY RADIATOR WATER WHEN HE REMOVED RADIATOR CAP TO CHECK WATER LEVEL.

INJ WAS HELPING3TO SERVICE AND HAUL TRUCKS, WHEN HE GOT SOME DIRT AND OIL IN HIS LEFT EYE

INJURED WAS CLI4BING OFF LOADER,WHEN HE SLIPPED OFF LAST STEP AND TWISTED RIGHT ANKLE.

WHILE EMPLOYEE 4AS CHANGING FLEXCOA ON CONVEYOR BELT BOLT PUNCTURED RIGHT PALM.

EMP ASSUMES THA7 HE PULLED A MUSCLE WHILE WORKING WITH A LENGTH OF 3/4" CHAIN

INJURED WAS ATT9MPTING TO MOVE ROLLAWAY CHUTE WITH PIPE.PIPE SLIPPED AND CAUGHT FINGER BETWEEN CHUTE AND SPRING MOUNT.