MERCER STONE PLANT Metal/Non-Metal

Crew was changing belt on BC-8 when the roll of belt being suspended by the boom truck shifted while pulling the belt and crushed little finger on right hand between the roll and the handrail of the man lift they was working from.

Employee's right foot slipped on loose ground causing EE to fall down the slope while checking pump. The employee landed on EE's right shoulder and right hip and struck the right side of EE's face. Out of an abundance of caution, emergency responders were called and the employee was taken to the hospital via ambulance.

Standard Threshold Shift

Hauler operator was driving back to the strip after dumping EE's load at the waste area. There was a washout on the road and as EE tried to avoid some of the washout EE's right front tire hit a rock and the cab of the articulated truck EE was driving shifted. EE said EE felt a pain in EE's left lower back down into EE's leg. The employee was taken to be medically examined.

Working in the Mercer Lab, employee was preparing a test sample. EE reached back with right arm to get gloves and said shoulder popped. EE said it hurt but EE worked the remainder of shift. Monday 6/14/21 EE reported the incident. The following Monday 6/21/21 EE reported it was still bothering EE. EE was taken to a medical clinic in Princeton WV to be evaluated.

Rolling a fuel hose off a hose reel and had the nozzle in hand and it twisted their right hand/wrist.

Employee was cleaning up around the shop, lifted a section of drill steel and strained back. EE was treated at clinic and released to work on light duty. Released to full duty on 08/21/2020.

Greasing equipment and while descending the excavator, EE put foot on the ground and EE's back popped. EE immediately felt pain in the lower back. EE was taken to medical office where EE was treated and released with restrictive duty. EE was examined again on Friday 5/29/2020 and was released to full duty.

Employee was returning hurriedly to the control room to shut down a feeder when they slipped and fell resulting in a sprain of the right knee.

After completing repair of the electronic eye that monitors belt rotation of the #10 belt, employee was returning to the man lift. While fully protected from falling by a fall protection system employee was preparing to re-enter the man lift. As man lift boomed closer employees fingers (left ring and pinky) were caught between the man lift and the structure.

While walking to the off road fuel tank, employee tripped over a piece of rebar that had extended out of a broken concrete curb. When EE fell a piece of concrete punctured EE's left leg.

Helping load a screen bearing in skid steer loader bucket. Bearing rolled pinching finger against side of loader bucket. Went to hospital some stitches required.

Plant maintenance, slipped in the mud and twisted ankle. Went to hospital found ankle was broke. Did not receive this until this date 03/15/18.

While assisting in carrying a wire cable, both employees slipped and fell due to mud conditions. Employee's wrist was cut by the cable by employee falling. Went to Princeton Community Hospital for attention. Treated and released after application of adhesive in lieu of stitches.

Drill operator had bee sting, allergic to same, used EPI Pen and then we took to Princeton Community Hospital where employee was treated and released.

Mechanic changing fuel filter on rock drill. Complained of chest pain, contacted EMS they responded, transported to Princeton Medical Center. Treated and released that day returned to work next day. Referred to family doctor for more follow up testing.

Routine maintenance, while loosening a bolt with a wrench, felt hand pop in left wrist. Felt like it was from a prior fracture 3 years earlier. Went for medical evaluation found employee had only a sprain.

Employee was handing a box of 1 1/2 inch x 10 inch bolts out the driver side window of a pickup when the box slipped out of his left hand, he tried to grab hold with his right hand and felt a pull in groin area.

Haul truck operator having chest pains and had taken 3 nitroglycerin pills during shift to treat pain. Called emergency response to treat and transport to hospital.

Using a Walk-Behind-Skid Steer loader to clean spillage from surge tunnel, unit slid sideways, causing hand and elbow to strike the side of the tunnel structure.

While descending steps from operators room at High Cal plant, employee stopped five steps from stairs end to pull a 1 1/2 inch water hose used for cleaning and felt a pain in his right bicep. Sent to hospital for evaluation.

Excavator operator loading overburden on truck when rock rolled from face of material against the front of cab of the machine. Weight of rock on the front lower part of the cab bent the operator control pedals partially lodging his right foot, which he quickly removed. Nothing broken or cuts, sent to doctor as a precautionary measure.

Mechanic was removing an ID tag from a hydraulic hose with a pocket knife, the knife slipped and he punctured his left palm of hand.

Employee was operating a CAT 236B skid steer loader on irregular surface area, the machine went forward and back shifting his neck in same direction of machine. This happened at 1:00PM employee requested to go to doctor at 2:10PM.

Employee was walking from MCC-1 aggregate primary to aggregate primary control tower and fell in mud and landed on left shoulder.

Employee stated he hurt his back while operating a CAT 226 during clean up of plant area. An inspection on this CAT 225 the following day by MSHA inspector found nothing relative to create a back injury. Employee must now be off work through the end of Sept is reason for filing injury report!

Using a come-a-long, tool broke hitting employee in the head.

Highway truck driver was exiting his truck, his foot slipped off the top step, fell into the truck parked next to him and then fell to the ground.

Plant operator was trimming a belt splice clamp on conveyor belt, knife slipped cutting his leg.

Individual was hammering on metal segment on a CAT D8N dozer when a piece of metal broke and hit him in the neck. Just a cut at the time, later on at 1:30PM he notified his superintendent. When he went to the doctor after his shift 3:00PM and was found that a small piece about the size of a needle had to be surgically removed. This was done on 6/25/13.

Injury not reported until 06/11/2013 at 11:15AM Highway Truck driver possible sprain to stomach area while opening hood on truck. Supervisor was present at the time, no indication given as to supervisor by the driver of any injury at that time. Injury reported as noted.

Highway delivery truck driver-Removing stone buildup on tailgate apron-Schotched the tailgate to keep the tailgate open in order to clean the area-Wheel choked slipped allowing tailgate to close under its own weight striking the drivers hand.

Individual complained of chest pain and shortness of breathe.

Employee was adjusting metal gate on a screen unit. Adjustment required a pry bar to be used to move the gate, the bar slipped and employee tried to catch the gate causing his little finger to be caught under the gate.

Exiting skid steer loader foot slipped both shins hit the bucket causing abrasion on right ankle and small bump on his left foot.

Plant operator was performing preshift check of the Primary screen system when he passed out. Employee was found by another employee who notified the supervisor, 911 was contacted at 7:40AM. Employee was alert and talking, Emergency services arrived 7:50, employee was allowed to walk to ambulance and transported to the hospital.

Removing drive pulley from motor with a come-a-long when metal wedge from the pulley plate broke, striking the EE in the face.

Operator slipped and fell while exiting a CAT 771-D haul truck.

EE was helping drill operator ee in changing bit and driver on Beetle Drill. The pipe wrench was to hold the steel to break the hammer loose to change the drill bit and driver. In doing so the operator moved the control lever to hold the pipe wrench in the opposite direction and the wrench hit ee on left leg above the knee.

Drill operator was helping mechanic remove a broken blow tube from inside the hammer on an Atlas Copco 785 Drill. The hammer and starter rod fell 2 and 1//2 feet from the spindle adapter, the hammer (400 to 500 pounds) landed on the operator left arm pinning between the drill table and hammer. The operators' left forearm was broken.

Operator was access haul truck/Stumbled on access steps to operators cab. Landed on his right wrist, worked for two and one half hours. Wrist began hurting and swelling, went to hospital at 10:00 AM. treated and released. In doctors care to date.

Injury occurred when replacing a conveyor belt, individual was trimming excess rubber from belt splice area when knife slipped, cutting individual in left arm.

Operator was exiting the drill unit cab and turned his right ankle. Operator was taken to Emergency Room due to pain and swelling of ankle.

Slipped on ice when exiting equipment to the ground. Strained back muscle.

Employee climbing access ladder to enter cab of machine pulled tendons in right wrist.

Trip and fall on excavated fill area-irregular surface area, breaking right wrist.

EE parked 769-C truck at fuel pump at end of shift. When preparing to exit cab, he pulled something in lower stomach area. After getting home and taking a shower he called supervisor to inform about going to ER. After leaving ER, he called supervisor to inform he had a hernia and an appointment with Dr. on 1/26/07.

Pulling air hose in shop to air tire up on truck. Pulled bicep muscle in right arm.

MECHANIC WAS PREPARING TO WELD PIN LOCK ON BOOM OF EXCAVATOR WHEN WELDER MISFIRED. EMPLOYEE TURNED TO GET AWAY FROM SMOKE & HE TRIPPED OVER A GASOLINE CAN & FELL TO THE GROUND ON HIS LEFT SHOULDER.

EE WAS HELPING DRILL OPERATOR PULL HOSE WHEN EE FELL AND INJURED LEFT ANKLE

HE WAS CUTTING A MINE BELT WITH BOX CUTTER. IT SLIPPED AND CUT HIS LEFT ARM.

EMPLOYEE WAS STANDING ON CATWALK ATTEMPTING TO CUT A CHUTE LOOSE WHEN THE CATWALK HE WAS STANDING ON FELL. EMPLOYEE SUFFERED BACK, PELVIC, ANKLE AND LEG INJURIES.

STEPPING DOWN OUT OF TRUCK LEFT FOOT SLIPPED FELL AND ALL OF BODY WEIGHT WENT ON LEFT SIDE OF BACK.

EE ASSISTING DRILLER LOAD DRILL STEEL AND HAMMER ONTO DRILL RIG.

HEAT EXHAUSTION DUE TO DRIVING HAUL TRUCK.

WAS GOING DOWN AN ENBANKMENT, SLIPPED AND FELL ALANDING ON A ROCK. HAS BACK CONTUSION AND POSSIBLE RIB FRACTURE.

WHILE WORKING ON TRUCK LIGHTS, NECK WAS STRAINED. WHILE DRIVING, PAIN BECAME SEVERE.

GPF-EMPLOYEE HAS RECEIVED A 10.26% AWARD FOR HEARING LOSS FROM THE WEST VIRGINIA WORKMEN'S COMPENSATION BOARD EFFECTIVE 10-22-97.

WAS HOLDING A BOARD FOR ANOTHER EE WHO WAS OPERATING A SAW, WHEN HAND CAME IN CONTACT WITH SAW BLADE.

EE WAS SHOVELING XXX STONE FORM UNDER PULLEY TOMAINTAIN EQUIPMENT OPERATION WHEN HE EXPERINECED LOWER BACK PAIN AND NUMBNESS IN HIP.

EE WAS LIFTING A PIECE OF METAL AND INCURRED BACK PAIN.

HE WAS CARRYING LARGE BOX TO SCALEHOUSE OFFICE FROM SUPERINTENDANTS' OFFICE BUILDING. BOX OBSTRUCTED VIEW AND HIT LEFT KNEE ON METAL POLE THAT WAS PLACED AS BARRIER.

MAINTENANCE MAN WAS REMOVING A PORTION OF EXHAUST PIPE (CAST IRON, APPROX. 16" IN DIA, WEIGHING APPROX. 40-60 LB) FROM A 769-C 35-TON CAT HAUL TRUCK. EXHAUST WAS UNBOLTED, BUT JOINT WAS STUCK. WHILE IN PROCESS OF BREAKING JOINT CONNECTION, THE UNION SUDDENLY BROKE AND SECTION OF EXHAUST FELL ON LEFT HAND, WHICH WAS POSITIONED ON TRUCK FRAME FOR SUPPORT AS SUBJECT WAS STANDING ON TH

EMPLOYEE WAS REMOVING METAL AIR INTAKE TUBING FROM ENGINE OF 988-B CAT END LOADER AND WAS STANDING ON CHAINED TIRE APPROX. 8 FT. ABOVE GROUND LEVEL. HE WAS USING A 3-FT. METAL PRYBAR "BLADE EN D" TO SEPARATE 8 IN. DIAMETER METAL AIR TUBING CONNECTION & WHILE EXERTING WEIGHT ON BAR, CONNECTION UNEXPECTEDLY & SUDDENLY BROKE CAUSING MECH. TO LOSE BALANCE, REACH OUT & HIT ARM ON METAL

STOCK TRUCK OPERATOR WAS OPERATING TRUCK STOCKING STONE. VISIBILITY BECAME POOR THROUGH WINDSHIELD (SNOW ICE BLOWING DUST) AND OPERATOR PARKED TRUCK..MOVED TO STAND ON RIGHT FRONT FENDER TO C LEAN WINDSHIELD. FENDER WAS COVERED WITH ICE WHICH WAS NOT VISIBLE. OPERATOR LOST FOOTING & FELL APPROXIMATELY 8' TO GROUND TEARING CARTILAGE IN LEFT KNEE.

EMPLOYEE WAS WELDING/WORKING ON METAL FRAMING (PLANT CONTROL BUILDING). CRAWLING UNDER CROSS MEMBER BUMPED RIGHT ELBOW ON 6" CHANNEL IRON CAUSING ELBOW TO SWELL.

OEPRATOR WAS OPERATING NORTHWEST 80-D DROP-BALL MACHINE BREAKING LARGE ROCKS. WAS PULLING BACK ON CABLE HOIST LEVER AND FELT PAIN IN BACK.

STANDING ON CAT WALK RECEIVING CANICA ANVILS (APPROX WT 40- LB EA) FROM FELLOW EMPLOYEE, TWISTED BODY AND TOSSED ANVILS APPROX 8-10 FT. FELT PAIN IN UPPER LEFT ARM AND LEFT CHEST AREA, NUMBNE SS IS LEFT ARM AND SHOULDER.

WHILE IN PROCESS OF CHARGING BATTERY IN PICKUP TRUCK (USING ELECTRICAL BATTERY CHARGER) INDIVIDUAL WAS DISCONNECTING CABLES FROM BATTERY & BATTERLY EXPLODED SMALL PIECE OF BATTERY HIT INDIVIDU AL IN UPPER LIP & ON END OF NOSE CUTTING BOTH

WHILE OPERATING 769-C CAT TRUCK ON HAUL ROAD, FELT PAIN IN LOWER BACK.

HIT LEFT ELBOW ON ENGINE COMPARTMENT DOOR WHILE REACHING WHERE OIL DIPSTICK WAS TO CHECK OIL LEVEL LEFT ELBOW HAS PAIN BUT NO SWELLING

WHILE CLOSING DRIVER'S SIDE DOOR ON #30471 CAT TRUCK, MASHED TIP OF INDEX FINGER ON RIGHT HAND. MASHED INDEX FINGER BETWEEN DOOR AND DOOR FRAME.

WHILE WALKING ON CATWALK OF #5 SCREEN, EE SLIPPED IN SNOW AND ICE AND FELL ON LEFT FOOT. LEFT FOOT NOT INJURED BUT PULLED GROIN.

WHILE WORKING ON CONSTRUCTION OF MAINTENANCE SHOP, WAS HANDING I-BEAM (APPROX. SIZE 22" X 40') WIGH ASSISTANCE OF TWO OTHER EMPLOYEES, TURNED BEAM FOR PURPOSE OF WELDING AND FELT PAIN IN LOWER MID BACK AREA.

CLIMBING ON TO NORTHWEST 180-D SHOVEL TO OEPRATE-STRAINED LEFT FLANK ON RIGHT LEG.

OPERATING JOY AIR TRACK DRILL WIND WAS BLOWING ROCK DUST FROM BORE HOLE BLEW INTO LEFT EYE.

WHILE WORKING ON METAL TOOL BOX IN SHOP WELDING SHED EE PICKED UP A PIECE OF FLAT SHEET METAL 1/4IN THICK X3FTX10FT BY HIMSELF ACCOUNT OF WEIGHT OF SHEET & AWKWARDNESS IT SLIPPED FROM HIS HAND S & MASHED RT HAND BETWEEN GROUND & METAL

USING GRINDER WIND BLEW METAL SHAVINGS IN R EYE

EMPLOYEE WAS BACKING ONTO SERGE PILE IN LOADED TRUCK TWO LARGE ROCKS ROLLED OUT OF TRUCK BED & REAR WHEELS RAN OVER ROCKS TRUCK WHEELS DROPPED OFF ROCKS EMPLOYEE BOUNCED OFF OPERATORS SEAT & W HEN HE LANDED BACK INTO SEAT FELT SHARP PAIN IN HIS BACK

EMPLOYEE STEPPED OFF CAT-WALK ON DRILL ONTO A ROCK AND ROCK TURNED OVER AND EMPLOYEE PULLED LIGAMENTS IN LEFT ANKLE.

EMPLOYEE WAS WELDING ON DOZER AND LIFTED SHIELD TO CHIP AWAY SLAG AND METAL SLIVER FLEW INTO LEFT EYE. FOREIGN OBJECT BECAME IMBEDDED IN PUPIL OF LEFT EYE.

EMPLOYEE WAS LIFTING A PORTABLE GENERATOR AND PULLED MUSCLES IN BACK ON LEFT SIDE, UPPER PART OF BACK.

EMPLOYEE I.NAME WAS UNLOADING STAPAC ROLLER FROM LOW-BOY TRAILER; ROLLER SLIPPED OFF RAMP SIDEWAYS AND I.NAME (WHO WAS IN THE OPERATOR'S SEAT) WAS THRUST AGAINST BRUISING THE LEFT SIDE OF HIS LOWER BACK.

"SOFTBALL SIZE" ROCK FELL FROM OVERHEAD OFF NO. 2 SCREENING UNIT AT CRUSHING PLANT AND STRUCK SUBJECT ON LOWER BACK.

EMPL I NAME WAS OPERATING A HOUGH H-400-C END LOADER IN PIT LOADING SHOT ROCK AND WHEEL HIT A LARGE ROCK AND CUASED THE STEERING WHEEL TO TURN AND STEERING KNOB STRUCK OPERATORS L WRIST

EMPLOYEE ADVISED OUR COMPANY 4:17 PM JULY 1,1989, THAT HE HAD HURT HIS BACK ON EVENING SHIFT JUNE 22,1989. HE STATED HE HURT HIS BACK ASSISTING IN LIFTING A 120 LB DRUM OF 90-W GREASE.

THE INJURED WAS ASSISTING ANOTHER EMPLOYEE IN ERECTING STRUCTURE FOR STURTEVANT SAND SEPARATOR.THE OTHER EMPLOYEE,OPERATING BANTAM TRUCK CRANE HAD SUSPENDED ON EPIECE OF 8"X21"X28 FT H-BEAM AN D THE EINJURED WAS HELPING PLACE H-BEAM.THE OTHER EMPLOYEE RECEIVED WRONG SIGNAL FROM GROUND AND LOWERED BEAM TRAPPING INJUREDS LEFT AHND BETWEEN TWO H-BEAMS.

EMPL WAS USING GRINDER AND WEARING GREEN TINTED SAFETY GLASSES IN CLOSE PROXIMITY APPROX 2 FEET TO COMPANY WELDERS WHO WERE REPAIRING AND WELDING ON STEEL PLATED IN JAW FEEDER EMPL RECEIVED FL ASH BURNS FORM WELDERS IN BOTH EYES NOT EMPL REPORTED ACCIDENT TO COMPANY 7:30 AM 4-24-89

I.NAME WHILE ASSISTING WELDER WAS ATTEMPTING TO FLIP OVER A PIECE OF 3/8 IN THICK X 7 FT WIDE X 8 FT LONG FLAT SHEET METAL DURING PROCESS OF LIFTING METAL I.NAME FELT BACK PAIN

EMPLOYEE WAS IN8IDE SYMONS CONE CRUSHER WHICH WAS STOPPED UP CLEANING OUT THE CRUSHER EMPLOYEE LEANED OVER IN THE CRUSHER TO REMOVE ROCK AND MATERIAL FROM OVERHEAD WITH A HOOK DURING THIS PRO CESS DUST AND S4ALL SAND PARTICLES FELL AND HIT EMPLOYEE ON LEFT SIDE OF FACE FOREIGN PARTICLES ENTERED LEFT EAR EMPLOYEE DID NOT HAVE CO PROVIEDED EAR PLUGS IN APPLICATION

I NAME WAS INJU9ED ON THE JOB 3-19-86 230 PM HOWEVER HE REPORTED NO ALLEGED INJURY .

F BODY AND FORCE APPLIED, PINNING HAND BETWEEN RATCHET HANDLE AND ROUGH EDGE OF BLADE OF KOMATSU DOZER. RING FINGER ON LEFT HAND BROKEN AND LITTLE FINGER ON LEFT HAND CUT.