PRESCOTT QUARRY: 117 MSHA citations Metal/Non-Metal

Employee stepped off concrete pad slipping and falling to the ground causing a concussion

Employee was servicing a loader. While working on the work platform of the loader, Employee mis-stepped and employee's foot left the platform and stepped down onto the top rung of the ladder, causing employee to lose balance falling 70" down onto a concrete floor. The employee landed on employee's feet, however sustained injuries to left foot and hip.

Injury was reported to employer on June 20, 2023 at 12:30 PM. Employee states, in mid-May IE was helping another EE change the top screen cloths on an 8x20' middle deck. The other EE cut the screen in 1/2 while IE was pulling up on the half screen. While pulling up IE states IE's neck and spine began to hurt.

Employee was using a hose to washout an area and strained their back.

Employee tried to push blow bar out of way as it was moving toward the employee, straining left shoulder.

Employee was trying to dislodge bearing in crusher shaft that was stuck, employee used prybar to move bearing, it fell down shaft and struck employee's finger and top of hand.

Employee tripped over rug outside of Scalehouse and fell. Striking head. Employee suffered head laceration and required 4 staples

Employee was walking and struck head on steel beam by the C15 tunnel. Forehead laceration requiring sutures.

Hood of haul truck fell on to employee thumb because it was not latched correctly.

EE was unloading a boxed fan with metal strapping. He reached behind the box where his R index finger caught an unseen piece of strapping sticking out.

Employee was cutting a corner shank off a bucket using a torch. When he chipped away the slag a piece flew on his face. When he went to brush it away, his welding gloves pushed the piece up into his eye.

Incident was not reported by employee until 6/30/09. Employee was using spray hose on water truck when he felt a pain in his groin. Condition has been diagnosed as an inguinal hernia

He was putting a screen on the top deck and felt a pull in his right arm.

GROUND FAILURE UNDER INGERSOL-RAND T4 BLASTHOLE DRILLING. DRILL WAS COMPLETING 150 ANGLE HOLE, 5.75" DIAMETER, APPROX. 40'DEPTH HIT VOID. DRILL HAMMER STUCK COMING UP & WHEN DRILLER "PULLED" ON THE HAMMER THE FACE GAVE WAY. 3-4 THOUSAND TONS OF LIMESTONE SLID OUT FROM UNDER RIG. DRILL LAY ON LEFT SIDE W/OPERATOR CAB UP.

USING A KNIFE TO CUT HOSE FOR WATERLINE, SLIPPED AND CUT HIS HAND.

HAND SLIPPED WHILE CLIMBING THE ACCESS LADDER OF A TEREX HAULER.

EMPLOYEE WAS STANDING BY 7X16 SHAKER PULLING A PUNCH PLATE UP WITH 2 OTHER EMPLOYEES WHEN HE FELT A SHARP PAIN IN THE ABDOMINAL AREA.

WORKING AROUND CRUSHER AREA WHEN A ROCK CAME OF A HIGH CONVEYOR AND HIT HIM IN RIGHT FOOT.

STEPPED ONTO CATWALK AND SLIPPED ON A OBJECT THAT WAS LAYING ON THE CATWALK.

THERE WAS A PILE OF ROCKS ON TAIL PULLY WERE I HAD THE INJURED PORTY CLEAN THEM OUT WHEN HE PULLED HIS LEFT GREM OUT.

COMALONG USED TO TIGHTEN UP HOSE TO NIPPLE ON STEEL LINE AND HANDLE A RACKET HANDLE SLIPPED AND HIT VICTIM IN R SIDE OF HEAD

MAN WAS HELPING TO MOVE ROLLS OF BELTS IN SHOP ASAID HE TWISTED LT KNEE CAUSING PAIN WAS NOT REPORTED UNTIL 1 WEEK LATER.

PIECE OF WIRE FROM WIRE BRUSH. WORKING ON PUMP.

I.NAME WAS IN THE PROCESS OF PERFORMING MORNING MAINTENANCE DUTIES ON OUR PORTABLE CRUSHER I.NAME SLIPPED & FELL HE FX.HIS ANKLE (LEFT FOOT) NOTE PORTABLE CRUSHER WAS NOT RUNNING AT THE TIME O F THE ACCIDENT OCCURRED

EMPL WAS BRIING STONE INTO CRUSHER & WENT TO GET ANOTHER BUC KET OF STONE FOR CRUSHER WHEN STONE GOT CAUGHT IN JAW OF CRUSHER. HE GOT OFF LOADER & WENT UP TO ASSIST IN GETTING STONE THRU C RUSHER WHEN STONE WAS THROUGH BELT WAS ACTIVATED & EMPL WAS ON ANOTHER VELTR NOT VISIBLE FROM CONTROL PANEL. UPON SEEING HIM COMING UP RETURN BELT FOR SCREEN MACHINE WAS SHUT OFF BY EMPL.

EMPLOYEE WAS ASSISTING IN THE INSTALLATION OF A SUMP PUMP FOR DUST CONTROL WATER WHEN HE AGGRAVATED AN OLD KNEE INJURY. KNEES BEGAN TO SWEEL MAKING IT DIFFICULT TO WALK.

PLACING WRENCH ON DRILL HAMMER,OTHER EMPL APPLIED WRONG PRESSURE,PINCHING RIGHT THUMB OF EMPL BETWEEN WRENCH AND DRILL FRAME.FRACURE OF RIGHT THUMB.